Simulation study of rate limiting factors of Li-ion batteries using experimental functions of electronic and ionic resistances
Not Available
Kondo, Hiroki (ORCID:0000000227089039)↗
SEARCH · Search NASA
Results for “ionic resistance”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Crossover Flux and Ionic Resistance Metrics in Polysulfide-Permanganate Redox Flow Battery Membranes
A survey of 23 commercially available cation exchange membranes was performed for the downselection of membranes for use in a polysulfide-permanganate redox flow battery (pS-Mn RFB). The survey measured the flux of permanganate ions across a 0.1 mol L −1 concentration gradient as well as the membrane resistance in a 0.5 mol L −1 sodium chloride solution. The membranes exhibited the characteristic flux/resistance trade-off observed in most classes of membranes. To connect the individual membrane testing to how the membranes will perform in a device, cell performance data in a pS-Mn RFB was collected for three membranes from the survey. The coulombic, voltaic, and energy efficiency at low cycle counts aligned with the predictions from the membrane flux and resistance survey results. The study also identified three membranes—Fumapem F-930-RFS, Fumapem FS-715-RFS, and Aquivion E98-09S—that outperformed most other membranes regarding their position on the flux-resistance trade-off curve, indicating them to be good candidates for further testing.
Electrochemistry↗
Ultrathin alkaline membranes with excellent hardness and gas barrier properties to achieve low ionic resistance and mechanical failure in high temperature water electrolyzers with low electrolyte
Explore the source record for details and available documents.
Hugar, Dr. Kristina M. [Ecolectro, Inc., Ithaca, N↗
Effect of H + Exchange and Surface Impurities on Bulk and Interfacial Electrochemistry of Garnet Solid Electrolytes
Contact loss and current constriction pose significant challenges at the Li metal interface of solid-state batteries. For garnet-structured Li 7 La 3 Zr 2 O 12 (LLZO), these effects are amplified by Li + /H + exchange and surface contamination reactions, which lead to conductivity losses and poor Li wetting. In this study, we utilize a variety of surface treatment processes across 37 cells to selectively induce proton exchange and contamination reactions in LLZO. The resulting bulk and surface chemistry is systematically characterized and correlated to changes in electrochemical properties. Additionally, we combine impedance analysis and finite element method modeling to deconvolute sources of impedance contributions at the Li metal interface. Specifically, we show that constriction impedance at the Li metal interface arises not solely from voids, but also from ionically-resistive surface contaminants. Further, these findings emphasize the connection between ionic conductivity and constriction, demonstrating that micron-scale ionically-resistive components increase constriction even with identical contact geometries. Finally, we leverage our comprehensive dataset to highlight unstable overpotential growth as a failure mechanism, additionally showing that the phase of a cell’s impedance is a sensitive indicator for the onset of interfacial instability. Overall, this study clarifies the impacts of proton exchange and surface contamination on electrochemical properties at the Li|solid electrolyte interface and elucidates insights that are generalizable to other solid-state battery systems.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Characterization and growth of epitaxial layers of Gs exhibiting high resistivity for ionic implantation
Either classical or low temperature epitaxial growth techniques can be used to control the deposition of buffer layers of GaAs on semiconducting substrates and to obtain the resistivity and purity desired. Techniques developed to study, as a function of thickness, the evolution of mobilities by photoHall, and the spectroscopy of shallow and deep centers by cathodoluminescence and current transients reveal one very pure layer of medium resistivity and high mobility, and another "dead layer" of elevated resistivity far from the surface. The highly resistive layer remains pure over several microns, which appears interesting for implantation.
Source record↗
Interplay of Electrode Heterogeneity and Lithium Plating
Lateral microstructure heterogeneity in anodes is known to induce nonuniform current density, state of charge, and lithium plating. This means that such electrode heterogeneity can limit the fast charging of lithium-ion batteries. In this work, a combination of experiments and simulation is employed to understand the effect of mm scale lateral heterogeneity on cell aging. A previously developed model was extended to efficiently simulate SEI formation and Li plating for independent regions of an electrode. The model consists of three parallel regions each described under a P2D framework and with a distinct ionic resistance and possibly active material loading. The results suggest that during fast charge when the active material is uniformly distributed across the three regions, the region with the highest resistance reaches the end of life sooner than the other regions. There is also positive feedback from Li metal filling the pores near the separator interface that further accelerates lithium plating. Lastly, when there is a non-uniform active material distribution associated with the ionic resistance heterogeneity, tight competition between regions can occur, leading to less overall lithium plating and plating that is more uniform between regions.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Deconvoluting the benefits of porosity distribution in layered electrodes on the electrochemical performance of Li-ion batteries
Thick Lithium Ion Battery (LIB) electrodes suffer from poor rate capability and high ionic impedance due to their thickness and mesostructure. Therefore, optimizing thick electrode architectures becomes crucial. In this work, we report a systematic assessment of the ionic resistance in heterogeneous porous electrodes through the combination of computational simulations using a 4D-resolved model and experimental measurements. The first part of the study is devoted to a general assessment of Electrochemical Impedance Spectroscopy (EIS) spectra, mapping the impact of ionic and electronic resistances on the overall impedances of uncalendered and calendered LiNi 1/3 Mn 1/3 Co 1/3 O 2 , LiFePO 4 and graphite electrodes. In the second part, in silico-generated electrodes with different porosities are used in computational EIS simulations to analyze the impact of the electrode porosity on the ionic impedance. As expected, the results show that a lower porosity leads to a higher ionic impedance because of a higher electrode tortuosity factor. Furthermore, in silico-generated electrodes with different porosities were stacked and assembled to create heterogeneities of porosity along the thickness, and used in computational EIS and galvanostatic discharge simulations. The computational results show that the porosity heterogeneity along the electrode thickness has a significant effect on the ionic impedance and capacity of the electrode. The electrode architecture with progressively decreasing porosity from separator to current collector shows the highest performance, a trend validated by our in house experimental EIS and galvanostatic discharge also reported in this manuscript. Overall, we conclude that the ionic resistance in a thick electrode can be effectively reduced through proper tuning of the porosity heterogeneity. The proposed heterogeneous electrode architectures presented here could enormously help building efficient thick electrodes for LIBs.
25 ENERGY STORAGE↗
Inexpensive cross-linked polymeric separators made from water soluble polymers
Polyvinyl alcohol (PVA) crosslinked chemically with aldehyde reagents produces membranes which demonstrate oxidation resistance, dimensional stability, low ionic resistivity, low zincate diffusivity, and low zinc dendrite penetration rate which make them suitable for use as alkaline battery separators. They are intrinsically low in cost and environmental health and safety problems associated with commercial production appear minimal. Preparation, property measurements, and cell test results in Ni/Zn and Ag/Zn cells are described and discussed.
Hsu, L. C.↗
Inexpensive cross-linked polymeric separators made from water-soluble polymers
Polyvinyl alcohol (PVA), cross-linked chemically with aldehyde reagents, produces membranes which demonstrate oxidation resistance, dimensional stability, low ionic resistivity (less than 0.8 Ohms sq cm), low zincate diffusivity (less than 1 x 10 to the -7th mols/sq cm per min), and low zinc dendrite penetration rate (greater than 350 min) which make them suitable for use as alkaline battery separators. They are intrinsically low in cost, and environmental health and safety problems associated with commercial production appear minimal. Preparation, property measurements, and cell test results in Ni/Zn and Ag/Zn cells are described and discussed.
Hsu, L.-C.↗
Ab Initio Simulation of Medium-Range Ordering in Ionic Glass Electrolytes LiSiPON and LiNaSiPON
Ionic glasses can exhibit a unique combination of optical transparency, electronic resistivity, ionic conductivity, and mechanical ductility. The origin of the relatively high ionic conductivity and ductility is poorly understood. Recently, these ionic glasses were found to have medium-range ordering (MRO) similar to that of metallic glasses. This MRO significantly impacts the properties of metallic glasses and is also expected to significantly impact the properties of ionic glasses. Here, this work used ab initio molecular dynamics (AIMD) simulations to study the effect of ionic glass composition on the MRO. The AIMD models showed that the degree of MRO increased as the temperature of the LiSiPON ionic glass decreased. The modeling also showed that the MRO is suppressed when 50% of Li is substituted with Na. This work lays the foundation for using AIMD to identify clear structure–property relationships in ionic glasses, allowing their properties to be optimized.
Osetsky, Yuri N. [Oak Ridge National Laboratory (O↗
Exploring the cell: Sodium (beta-alumina) cupric chloride - Aluminum chloride - Sodium chloride between 136 and 200 C
Experiments were done with a molten-salt catholyte (initially CuCl2 in AlCl3-NaCl) separated from molten Na by beta alumina. The open-circuit reduction potentials were 4.3 and 3 volts for Cu++ and Cu+, respectively. High polarization and nonrechargeability characterized the cell's operation. The cell's ohmic resistance during discharge was higher than what would be expected from only the ionic resistance of the beta-alumina.
Miller, R. O.↗
Experimental observation of electrochemical rate limitations affecting sodium ion-electron recombination at electrodes of the alkali metal thermoelectric converter at T about 1200 K
This paper considers a model of the internal impedances of thin porous Mo and W alkali metal thermoelectric converter (AMTEC), in which the kinetic parameters associated with the reaction of the beta-double-prime alumina solid electrolite (BASE)/porous metal/gas three-phase boundary can be evaluated. Impedance data in the frequency range 0.01-100,000 Hz were collected over a range of AMTEC cell operating voltages for small-area thin porous Mo and W electrodes, yielding apparent charge transfer resistances at a series of cell potentials/currents. The ohmic resistance in the AMTEC cell could be broken down and characterized with three parameters: the BASE ionic resistance, the electrode film sheet resistance, and the contact/lead resistance, all of which could be calculated or measured independently and used to calculate power curves in good agreement with observed power curves. It is shown that these calculations can be used to predict the properties of electrodes with optimized parameters or to detect enhanced transport modes.
Williams, R. M.↗
Quantification of [MTBD][beti] loading and its effects on Pt/HSC electrode performance in hydrogen fuel cells
High surface area carbon-supported platinum catalysts (Pt/HSC) are widely used in polymer electrolyte membrane fuel cells but often suffer from limited proton and oxygen transport within porous domains. To address these challenges, we integrate the ionic liquid [MTBD][beti] into Pt/HSC catalyst layers using two deposition methods-one-pot and sequential deposition-to tune IL distribution within micropores and mesopores. A combination of ex situ and in operando techniques were employed to elucidate electrode structure-performance relationships across a range of IL loadings. Sequential deposition achieved more efficient pore filling and higher IL retention at lower IL:C ratios, enabling enhanced proton conductivity and protection of active sites. Compared to the IL-free Pt/HSC, IL-modified electrodes demonstrated up to 28% improvement in mass activity and enhanced high-current-density performance under low relative humidity, while maintaining comparable performance under humidified conditions. Electrochemical impedance spectroscopy and CO displacement experiments reveal that improvements are linked to reduced ionic resistance and lower sulfonate adsorption on Pt sites, rather than changes in electrochemical surface area. However, excessive IL loading leads to mass transport losses. These results highlight the importance of selective pore filling and efficient IL distribution in achieving kinetic gains without compromising ionic and gas transport.
08 HYDROGEN↗
Interface potentials inside solid-state batteries: Origins and implications
Interface resistance has become a significant bottleneck for solid-state batteries (SSBs). Most studies of interface resistance have focused on extrinsic mechanisms such as interface reactions and imperfect contact between electrodes and solid electrolytes. Interface potentials are an important intrinsic mechanism that is often ignored. Here, we highlight Kelvin probe force microscopy (KPFM) as a tool to image the local potential at interfaces inside SSBs, examining the existing literature and discussing challenges in interpretation. Drawing analogies with electron transport in metal/semiconductor interfaces, we showcase a formalism that predicts intrinsic ionic resistance based on the properties of the contacting phases, and we emphasize that future battery designs should start from material pairs with low intrinsic resistance. Here, we conclude by outlining future directions in the study of interface potentials through both theory and experiment.
25 ENERGY STORAGE↗
Nanoscopic Plugs Block Hydrogen Crossover in Submicron Thick Proton-Conducting SiO 2 Membranes for Water Electrolysis
Zero-gap electrolyzers based on submicron thick proton-conducting oxide membranes (POMs) represent a promising approach to increasing the efficiency of H 2 production from water electrolysis while moving away from conventional perfluorosulfonic acid (PFSA) membranes. A critical barrier to the commercialization of such electrolyzers is that the ultrathin nature of POMs, which is necessary to achieve low cell resistance, makes them more susceptible to defects that can lead to unacceptably high rates of H 2 crossover. Herein, we demonstrate an approach to mitigate this problem through selective deposition of carbon-containing silicon oxide (SiO x C y ) “nanoplugs” into the defects of submicron thick SiO 2 membranes using a facile electrochemically mediated deposition process. Selective deposition of nanoplugs within the defects was verified by multiple characterization techniques, while scanning electrochemical microscopy (SECM) was used to confirm selective plugging of H 2 -crossover hotspots associated with defects at identical locations. Thanks to the use of nanoplugs, the H 2 permeance of 250 nm thick SiO 2 membranes was reduced by 5 to 6 orders of magnitude compared to the unmodified atomic layer deposition (ALD) SiO 2 membranes while having negligible impact on the ionic resistance of the membrane. These plug-modified membranes also enabled safe and stable operation of a zero-gap full cell electrolysis cell, in contrast to cells lacking nanoplugs that produced anode effluent streams having H 2 concentrations near or exceeding the lower flammability limit (LFL) of H 2 . Furthermore, beyond water electrolysis, this defect-sealing strategy has the potential to be broadly implemented in other applications, such as fuel cells and flow batteries, offering a versatile solution to mitigate crossover-related performance losses.
ALD SiO2↗
Broad Applicability of Electrochemical Impedance Spectroscopy to the Measurement of Oxygen Nonstoichiometry in Mixed Ion and Electron Conductors
Oxygen non-stoichiometry is a fundamental feature of mixed ion and electron conductors (MIECs). In this work a general electrochemical method for determining non-stoichiometry in thin film MIECs, via measurement of the chemical capacitance, is demonstrated using ceria and ceria-zirconia (Ce 0.8 Zr 0.2 O 2-δ ) as representative materials. A.C. impedance data are collected from both materials at high temperature (750-900 °C) under reducing conditions with oxygen partial pressure (pO 2 ) in the range 10-13 to 10-20 atm. Additional measurements of ceria-zirconia films are made under relatively oxidizing conditions with pO 2 in the range 0.2 to 10 -4 atm and temperatures of 800-900 °C. Under reducing conditions, the impedance spectra are described by a simple circuit in which a resistor is in series with a resistor and capacitor in parallel, and thickness dependent measurements are used to resolve the capacitance into interfacial and chemical terms. Under more oxidizing conditions, the impedance spectra (of Ce 0.8 Zr 0.2 O 2-δ ) reveal an additional diffusional feature, which enables determination of the ionic resistance of the film in addition to the capacitance, and hence the transport properties. A generalized mathematical formalism is presented for recovering the non-stoichiometry from the chemical capacitance, without recourse to defect chemical models. The ceria non-stoichiometry values are in good agreement with literature values determined by thermogravimetric measurements but display considerably less scatter and are collected on considerably shorter timescales. Here, the thermodynamic analysis of Ce 0.8 Zr 0.2 O 2-δ corroborates earlier findings that introduction of Zr into ceria enhances its reducibility.
08 HYDROGEN↗
Effect of Propagating Dopant Reactivity on Lattice Oxygen Loss in LLZO Solid Electrolyte Contacted with Lithium Metal
Lithium lanthanum zirconium oxide (LLZO) is widely known as the most stable solid electrolyte against lithium metal electrodes. This thermodynamic stability can be lost by the presence of dopants which are required to stabilize the cubic phase of LLZO and can be reduced by lithium metal. However, the role of oxygen in such reactions is taken for granted. In this work, the reduction of Nb-substituted LLZO (Nb-LLZO) is explored by Li metal and shows that interfacial reactions propagate and lead to the decomposition with substantial Nb 5+ reduction deep into the bulk electrolyte. Scanning Transmission Electron Microscopy with Energy Dispersive X-ray Spectroscopy and thermogravimetric analyses show much of the reduction is due to oxygen vacancies formed, leading to increased electronic conductivity mapped with conductive Atomic Force Microscopy. Density functional theory calculations indicate oxygen release is favored by increased excess lithiation of Nb-LLZO. Electrochemical impedance of polycrystalline Nb-LLZO shows the continuous evolution of ionically resistive interphases near the lithium metal interface with Nb-LLZO while single crystals show little reactivity at room temperature and self-limiting reduction at 60°C. This work underlines the role of grain boundaries in propagating destructive solid electrolyte reactions and highlights previously unseen mechanisms involving lattice oxygen in LLZO.
Li metal, solid-state electrolytes↗
Anode‐Free Lithium–Sulfur Cells Enabled by Rationally Tuning Lithium Polysulfide Molecules
Abstract The two major barriers of practical lithium–sulfur batteries are the poor reversibility of lithium‐metal anode and sluggish kinetics of sulfur cathode. Here, we report a simple yet cogent, molecular tailoring approach for lithium polysulfides, enabling a synergistic enhancement of anode reversibility and cathode kinetics. We show that SnI 4 coordinates with lithium polysulfides to form soluble complexes, resulting in a Li 2 SnS 3 ‐rich anode interphase layer. As Li 2 SnS 3 is stable against parasitic reactions and has a lower ionic resistance over cycling, the Li plating/stripping efficiency is greatly improved. In addition, the formation of soluble complexes between SnI 4 and lithium polysulfides play a non‐negligible role in suppressing the clustering behavior of lithium polysulfide molecules, resulting in a significant enhancement in sulfur conversion kinetics under lean electrolyte conditions. The synergistic improvement is validated in anode‐free, lean‐electrolyte pouch cells with a Li 2 S cathode that displays capacity retention of 78 % after 100 cycles.
Ren, Yuxun↗