Search NASA⌕ Search

SEARCH · Search NASA

Results for “iron-chromium-aluminum”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Iron-Chromium-Aluminum Accident Tolerant Fuel Concept Source Term Accident Sequence Analysis - High Burnup Fuel Source Term Accident Sequence Analysis Supplement

To extend NUREG-1465 and high burnup fuel source term (SAND2023-01313) recommendations, representative radiological releases to containment – patterned after NUREG-1465 – have been evaluated for LWRs utilizing iron-chromium-aluminum (FeCrAl) alloys in place of zirconium-based alloys in major core structures (cladding and fuel canisters) and high burnup fuel with enrichments of 8% and 10% for PWRs and BWRs, respectively. Representative radionuclide releases are generated for this accident tolerant fuel concept by applying non-parametric bootstrap methods to MELCOR simulation results. Accident scenarios considered in this analysis include principle contributors to historical core damage frequency estimates for a range of nuclear reactor technologies representative of the operating U.S.A. fleet of nuclear reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Analysis of iron-chromium-aluminum samples exposed to accident conditions followed by quench in the QUENCH-19 experiment

The QUENCH-19 experiment was a first-of-its-kind full-bundle test simulating accident conditions followed by water quench on accident-tolerant fuel (ATF) cladding. Here, a type of FeCrAl(Y) alloy, B136Y3, was developed at Oak Ridge National Laboratory and tested at the Karlsruhe Institute of Technology using Kanthal APM corner rods, a shroud, and Kanthal AF spacer grids. Testing conditions were similar to those in QUENCH-15—which tested ZIRLO cladding behavior—so that B136Y3 and ZIRLO cladding could be compared. QUENCH-19 consisted of an initial pre-oxidation heating followed by a transient. Then, a maximum power hold, which was not present in QUENCH-15, was executed to extend the heating period for the FeCrAl(Y) rods. Finally, a rapid water quench was executed that was similar to emergency core coolant system (ECCS) actuation. Compared with the ZIRLO rods in QUENCH-15, the bundle in QUENCH-19 released significantly less H 2 (9.2 g vs. 47.6 g) and achieved a much lower maximum temperature (1455°C vs. 1880°C). Furthermore, no breakaway oxidation was observed in QUENCH-19. Metallographic mounts revealed that despite the symmetry of the setup, at elevations near the maximum temperature, cladding and thermocouples were heavily damaged, substantial melting and oxidation occurred, and the cladding underwent chemical interaction with the thermocouple sheaths. Additionally, the ZrO 2 spacers detrimentally interacted with the cladding, leading to mixed oxide debris and the full destruction of some rods. Additional failure was found in certain cooler rods that may have risen due to the high thermal expansion coefficient of FeCrAl alloys. This paper presents an analysis of this work, which suggests that FeCrAl cladding can chemically survive anticipated loss-of-coolant accident events followed by rapid ECCS quench if the correct geometry and core design are present.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hydrogen permeation in iron-chromium-aluminum (FeCrAl) alloys and the effects of microstructure and surface oxide

Iron–chromium–aluminum (FeCrAl) class alloys are candidates for use as cladding for accident-tolerant fuels and moderators. In this context, hydrogen isotope permeation in FeCrAl alloys is an important material property. Here, in the present work, the apparent permeability, effective diffusivity, and apparent solubility of hydrogen in the FeCrAl alloys C26M and Kanthal D (KD) were measured with gas-driven hydrogen permeation. Permeation measurements were conducted at temperatures of 400 to 700 °C and at gas-driven pressures from 1 to 100 kPa. In particular, the effect of grain size on hydrogen transport was studied with KD samples with three different microstructures: nanocrystalline (NC), ultra-fine grained (UFG), and coarse-grained (CG). The UFG and NC specimens had higher apparent activation energies (73.4 kJ mol -1 and 65.2 kJ mol -1 , respectively) for hydrogen permeability than the CG sample (46.9 kJ mol -1 ). An aluminum oxide layer formed on the primary- and secondary-side surfaces of all samples subjected to permeation experiments which demonstrated the propensity of FeCrAl alloys to form these innate oxide permeation barriers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Micromechanical aspects of deformation and failure of advanced Iron-Chromium-Aluminum alloys

Here this work investigates the micromechanical deformation and failure mechanisms of advanced FeCrAl alloys developed for use in nuclear reactors as cladding material. Three different FeCrAl alloys (82-X)Fe-13Cr-5Al-X (X=Nb, TiC, 0 for base alloy) were investigated both in their as-received and welded states. In-situ neutron diffraction with simultaneous digital image correlation was used to determine micromechanical deformation mechanisms not only as a function of elemental composition but also as a condition of state (as-received vs. welded). Ex-situ X-ray computed tomography was used on as-deformed samples to help determine the failure mechanisms and void initiation strains.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-temperature steam oxidation study of irradiated FeCrAl defueled specimens

Post irradiation examinations (PIE) were performed on irradiated iron-chromium-aluminum (FeCrAl) specimens. These FeCrAl specimens were fabricated at the US Department of Energy's Oak Ridge National Laboratory (ORNL). The experimental setup involved subjecting FeCrAl cladding, along with UO 2 pellets, to irradiation in the Idaho National Laboratory Advanced Test Reactor (ATR). In parallel, the FeCrAl alloy tubing without UO 2 pellets was irradiated at ORNL's High Flux Isotope Reactor (HFIR). After irradiation, the ATR-irradiated rodlet was transported to an ORNL hot cell, where it was sectioned into multiple samples for the PIE and severe-accident testing. The sectioning process revealed that the fuel was not bonded to the cladding and could be easily detached from sectioned cladding slices. Microstructural analysis of the fuel cross sections demonstrated no significant interaction between the fuel and the cladding. Additionally, high-temperature steam oxidation tests on defueled cladding segments showed minimal oxygen uptake even at 1200 °C. Here, the ATR-irradiated specimens began to exhibit signs of enhanced oxidation upon reaching a temperature of 1300 °C. Furthermore, enhanced oxidation was observed on the inner surface of the ATR-irradiated FeCrAl specimen, which had been subjected to 1300 °C for a duration of 1 min. By contrast, high-temperature steam oxidation experiments indicated that the HFIR-irradiated FeCrAl cladding provided good thermal stability when exposed to 1300 °C for up to 4 h. Comparative analysis encompassing the oxidation behavior of the ATR-irradiated fueled FeCrAl, HFIR-irradiated unfueled FeCrAl, and unirradiated FeCrAl suggests that the fuel–cladding interaction, although not visible via standard microscale electron microscopy measurements, may accelerate the deterioration of FeCrAl cladding in beyond-design-basis accident scenarios.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Hydrogen Permeation in FeCrAl APMT Alloy for Accident Tolerant Fuel Cladding

Iron-chromium-aluminum (FeCrAl) alloys such as APMT (advanced powder metallurgy tubing) are candidate materials to replace zirconium alloys for the light water reactor fuel cladding. This alloy meets the requirements to be a material more tolerant of high-temperature accidents than the current zirconium alloys. One concern is that the use of FeCrAl may result in an increase in tritium presence in the coolant compared to the current design. The aim of the current research was to obtain effective diffusion coefficients (D eff ) for hydrogen through APMT using the Devanathan-Stachurski cell. Results showed that at 30°C the D eff value was 2.8 × 10 -8 cm 2 /s. Results also showed a linear relationship between the permeated hydrogen flux and the inverse of the test specimen thickness, which demonstrated the validity of the permeation measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhanced Mechanical Properties and Wear Resistance of FeCrAl Alloys at ~ 300°C and Higher Temperatures

Abstract Worldwide, light water reactors (LWRs) have been using zirconium (Zr)-based alloys for the cladding of the uranium dioxide fuel for more than 6 decades. Zr alloys oxidize rapidly in the presence of water and steam at temperatures > 450°C; therefore, they do not respond well to scenarios of loss of coolant accidents. There is a global effort by nuclear materials technologists to find more robust or stronger cladding materials for LWRs. One option is to use an iron-chromium-aluminum (FeCrAl) alloy since they have excellent resistance to high temperature oxidation and superior mechanical properties at LWR operation temperatures. Results show that (1) FeCrAl alloys have better mechanical properties than Zr alloy and are orders of magnitude more resistant to creep at temperatures higher than LWR normal operation conditions. (2) FeCrAl alloys have better resistance to fretting wear than Zr alloys at the normal operation conditions of LWRs.

Materials Science↗
DOE OSTI2022

Improved irradiation resistance of accident-tolerant high-strength FeCrAl alloys with heterogeneous structures

In this work, post–neutron irradiation examination is performed on advanced accident-tolerant fuel (ATF) cladding iron-chromium-aluminum (FeCrAl) alloys with ~10–13at. % Cr, ~10–12 at. % Al, ~1 at. % Mo, and minor alloying elements including Y irradiated to a damage level of 7 displacements per atom (dpa) at irradiation temperatures of 267–282 °C. A compositional dependency of the Cr and Al content is observed on the ratio of sessile and glissile dislocation loops, where the density of a$\langle$100$\rangle$ type loops is somewhat higher than the a/2$\langle$111$\rangle$ type loops. The α' precipitate number density is inversely correlated to the starting Cr concentration of the alloys of interest. The irradiation to a higher dose of 7 dpa results in a higher density of dislocation loops and α' precipitates for the same alloys at a lower irradiation dose, such as 1.8 dpa. In this work, the effect of α' precipitates on the dislocation loop density is discussed, and the presence of α' appears to inhibit the nucleation of loops. Compared with first-generation FeCrAl alloys, these advanced alloys with heterogeneous structure exhibit a lower Cr concentration in α' precipitation at the same dose level; they act as weaker obstacles deviating from the primary hardening contribution from the mature α'. Hence, the overall irradiation-induced hardening decreases; our alloys show improved radiation resistance because of their stronger sink strengths. The results presented in this paper could provide insights for the design and optimization of ATF cladding materials for future fission and space applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Selective laser melting of oxide dispersion strengthened MA956 alloy and its surface finishing by magnetic field assisted finishing

Selective laser melting (SLM) is a prominent metal additive manufacturing (AM) capable of processing a myriad of engineering materials with high precision and design freedom. However, similar to other AM processes, poor surface finishing has been an omnipresent problem in SLM technology. In this study, magnetic field assisted finishing (MAF) was used to finish SLM fabricated oxide dispersion strengthened (ODS) MA956, an iron-chromium-aluminum alloy. The effect of laser processing parameters on part density and surface roughness was first studied. Using a multi-objective optimization technique, the optimal parameters to obtain the highest density and lowest surface roughness were determined. Finally, MAF was applied to the parts built with the obtained optimal SLM parameters, but without significant improvement on the surfaces of as-printed samples. Hence, the surfaces of as-printed samples were post-processed (ground) to yield better initial surface conditions prior to MAF. The effect of initial roughness, iron particles size, and abrasive size on MAF performance was studied. Initial roughness had the most dominant effect followed by abrasive size. The underlying mechanism behind the dependency on initial roughness on final surface quality was analyzed by studying the change on the surface profiles with different starting initial roughness. The initial roughness required for MAF to be effective was determined. In conclusion, using the optimal processing conditions, MAF was applied to the post-processed samples to attain the final average surface roughness (R a ) as little as 0.36 μm starting from initial average roughness (R a ) of 1.53 μm.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strength and rupture geometry of un-irradiated C26M FeCrAl under LOCA burst testing conditions

Ferritic iron-chromium-aluminum (FeCrAl) alloys are an accident tolerant fuel candidate to replace the incumbent Zr-based claddings. Nuclear grade FeCrAl alloys are marked by superior high temperature mechanical behavior and exceptional steam oxidation resistance, both of which increase safety margins during accident scenarios. In the present study, the loss of coolant accident (LOCA) burst behaviors of three un-irradiated commercially fabricated cladding materials in a simulated LOCA environment were compared: (1) T35Y2, a 1 st generation nuclear grade FeCrAl, (2) C26M, a 2 nd generation nuclear grade FeCrAl, and (3) Zircaloy-2. Both FeCrAl alloys showed improved mechanical strength and steam oxidation resistance compared to Zircaloy-2. C26M claddings burst at significantly higher temperatures for all tested engineering hoop stresses, had limited ballooning, and demonstrated preferential fuel retention behavior in terms of burst opening area and length. High temperature tensile data for C26M is also presented. For both un-irradiated FeCrAl alloys, it was found that a distinct “threshold” burst stress signified the transition between small and large openings. Finally, higher threshold hoop stresses were associated with higher uniaxial strength for the FeCrAl alloys, indicating that tensile data, rather than creep data, could be useful for predicting rupture size and assessing fuel dispersal concerns.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A comparison of wrought and powder metallurgical FeCrAl claddings under simulated LWR accident transients

Iron-chromium-aluminum (FeCrAl) alloys are potential accident tolerant fuel (ATF) cladding candidates for light-water reactors but are difficult to fabricate as thin-walled tubes via conventional cast-and-wrought routes. Powder metallurgy (PM) offers a manufacturing alternative with improved compositional control, but its transient accident performance has not been directly benchmarked against wrought variants. This study evaluates the burst behavior of commercially developed PM-processed FeCrAl alloys, PM-C26M (Fe-12Cr-6Al-2Mo) and the high precipitate density FA-SMT (Fe-22Cr-5Al-3Mo), under simulated light-water reactor accident transient conditions. Burst testing was conducted using the Severe Accident Test Station with heating rates of 5 °C/s and 50 °C/s and internal pressures ranging from 25 MPa to 100 MPa. PM-C26M reproduced wrought C26M burst behavior within 7–37 °C across the stress range, indicating that PM processing does not compromise transient strength. FA-SMT exhibited markedly higher burst temperatures and reduced heating-rate sensitivity, consistent with its engineered precipitate strengthening. FA-SMT rupture exhibited axial "unzipping" rather than the lateral tearing characteristic of PM- and wrought C26M. Post-test EBSD and fractography indicate that this behavior is strongly correlated with strain-gated intergranular void nucleation associated with the dense precipitate architecture of FA-SMT, a response absent in the comparatively clean PM-C26M matrix and consistent with rupture morphologies reported for oxide-dispersion strengthened (ODS) FeCrAl of similar base-matrix chemistry to PM-C26M. These findings highlight the potential of powder metallurgy as a viable fabrication route for ATF claddings from an accident performance standpoint.

Bell, Sam [ORNL] (ORCID:0000000251905657)↗
DOE OSTI2025

A Standardized Analysis Process Using Digital Image Correlation to Calculate In Situ Cladding Strain from Modified Burst Tests for Fuel Performance Code Validation

Historical data collection on nuclear fuel cladding materials has focused on generating a statistically significant amount of data to assess the material and its failure behavior. Furthermore, data generated to support material model and failure criteria development were previously posttest evaluations, so a large number of tests was required to gain new understanding. A way to expedite this process is to develop techniques capable of generating large, high-fidelity data sets from a single test with lower uncertainty or quantified uncertainty. One such example of this approach is Oak Ridge National Laboratory’s use of modified burst tests (MBTs) to analyze the mechanical behavior and failure conditions of cladding during a simulated reactivity-initiated accident (RIA). Each test incorporates digital image correlation (DIC) analysis techniques that are used to assess the accumulated strain in situ, as well as eventual cladding failure. This work has been fruitful in defining strain-to-failure conditions for materials like silicon carbide (SiC) fiber–reinforced/SiC matrix composite tubes (SiC/SiC), iron-chromium-aluminum (FeCrAl) alloy tubes, and chromium-coated Zircaloy-4 tubes. However, there are numerous DIC software available, including open-source and proprietary software. The different DIC software use various algorithms to process images and calculate displacement values. Using these different software and algorithms can lead to varying results, and perhaps larger-than-expected uncertainties. In the present study, previously published MBT data encompassing a variety of test conditions were reanalyzed with two different DIC software to assess the variance in the calculated strain results. The data consisted of SiC/SiC, FeCrAl, and chromium-coated Zircaloy-4 tubes. Plots of the calculated strains during the transient revealed good agreement between the two DIC software. The average root-mean-square errors between the two software was 0.20% strain, which is slightly larger than a previously reported error value for these tests. In conclusion, this variance in results is low enough that this analysis method can be used for code validation.

Reactivity-initiated accident↗
DOE OSTI2023

Effect of surface oxides on tritium entrance and permeation in FeCrAl alloys for nuclear fuel cladding: a review

Abstract Iron-chromium-aluminum (FeCrAl) alloys are being considered for the cladding of uranium dioxide fuel in light water reactors (LWRs). FeCrAl alloys have good mechanical properties at temperatures of 300 °C and higher, and have superlative resistance to attack by steam at temperatures of up to 1000 °C and higher. A concern has been raised that the use of FeCrAl for cladding would result in a higher content of tritium in the reactor coolant as compared with the current system where the cladding is a zirconium based alloy. This review shows that the flux of tritium from the fuel rod cavities to the coolant across the fuel cladding wall will be greatly reduced by the presence of oxides on the surface of the cladding. The review of current literature and permeation data show that (a) protective oxides are expected to be present on both sides of the FeCrAl cladding, and (b) depending on the characteristics of these oxide layers it is reasonable to expect about two–three orders of magnitude reduction in tritium permeation, relative to the permeation response in clean, unoxidized condition for FeCrAl steels of interest, around 277 °C–377 °C temperatures.

Electrochemistry↗
DOE OSTI2024

Embedded Aluminum Nitride Sensors for Advanced Reactors

This project aims to manipulate the of growth of aluminum nitride (AlN) inclusions in an iron-chromium-aluminum (FeCrAl) alloy, using the principle of powder metallurgy and heat treatment methods. to promote the formation of AlN phase within FeCrAl for embedded sensing. This effort seeks to fill in a gap with respect to robust sensor hardware for ubiquitous structural health monitoring of advanced nuclear reactors. A systematic evaluation of various solid-state methods will be performed to understand the influence of process conditions on AlN growth and to promote the growth of desirable AlN phase. Fabricated specimens will be analyzed to investigate the AlN structures that are formed using a suite of tools to characterize the concentration, morphology, and distribution of AlN within the FeCrAl substrate.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Acid Dissolution Behavior of Ferritic FeCrAl Tubes Candidates for Nuclear Fuel Cladding

The international materials community is engaged in finding safer alternatives to zirconium alloys for the cladding of fuel in light water reactors. One solution is to replace the zirconium cladding using ferritic iron-chromium-aluminum (FeCrAl) alloys, which offer extraordinary resistance to high-temperature reaction with air or steam due to the formation of a protective alumina layer on the external surface. It is important to characterize the behavior of FeCrAl not only during accident conditions but in the entire fuel cycle, which may include reprocessing of the used fuel after it is removed from the power reactors. The reprocessing may involve the dissolution of the fuel rods in mineral acids. Little or nothing is known on the dissolution of FeCrAl alloys in common mineral acids, therefore the objective of this research was to study the dissolution of typical cladding tubing having two compositions of FeCrAl (APMT and C26M) in three acids (H 2 SO 4 , HNO 3 , and HCl) as a function of the temperature using both standard ASTM immersion tests as well as electrochemical tests. The dissolution behavior of the FeCrAl alloys is compared to the dissolution capability of other traditional nuclear materials such as austenitic stainless steels (304SS and 316SS) and austenitic nickel alloys (Alloy 600 and Hastelloy C-276). Results show that both C26M and APMT have a higher dissolution capability in the studied mineral acids, which will be beneficial for reprocessing procedures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Innovative Accident Tolerant Fuel Materials May Help Extending the Life of Light Water Reactors: A Perspective

One of the main sources of clean electricity in the civilian power grid comes from light water reactors (LWRs). Some of these LWRs are being decommissioned prematurely because they may not be economically sustainable. It is proposed that the use of accident-tolerant fuel concepts may enable for LWR plant operation extension by making them safer and more economically competitive to operate. For example, the use of iron-chromium-aluminum (FeCrAl) alloys for the cladding of the fuel would not only reduce the risk of catastrophic reaction between the cladding and its environment in the case of a loss of coolant accident situation but also, for example, allow for higher fuel burnup during normal plant operation.

Materials Science↗
NASA NTRS1972

Oxidation resistant porous material for transpiration cooled vanes

Porous metal sheet with controlled permeability was made by space winding and diffusion bonding fine wire. Two iron-chromium-aluminum alloys and three-chromium alloys were used: GE 1541 (Fe-Cr-Al-Y), H 875 (Fe-Cr-Al-Si), TD Ni Cr, DH 245 (Ni-Cr-Al-Si) and DH 242 (Ni-Cr-Si-Cb). GE 1541 and H 875 were shown in initial tests to have greater oxidation resistance than the other candidate alloys and were therefore tested more extensively. These two materials were cyclic furnace oxidation tested in air at 1800 and 2000 F for accumulated exposure times of 4, 16, 64, 100, 200, 300, 400, 500, and and 600 hours. Oxidation weight gain, permeability change and mechanical properties were determined after exposure. Metallographic examination was performed to determine effects of exposure on the porous metal and electron beam weld joints of porous sheet to IN 100 strut material. Hundred hour stress rupture life and tensile tests were performed at 1800 F. Both alloys had excellent oxidation resistance and retention of mechanical properties and appear suitable for use as transpiration cooling materials in high temperature gas turbine engines.

Madsen, P.↗
NASA NTRS1985

High temperature static strain gage alloy development program

The literature, applicable theory and finally an experimental program were used to identify new candidate alloy systems for use as the electrical resistance elements in static strain gages up to 1250K. The program goals were 50 hours of use in the environment of a test stand gas turbine engine with measurement accuracies equal to or better than 10 percent of full scale for strains up to + or - 2000 microstrain. As part of this effort, a computerized electrical resistance measurement system was constructed for use at temperatures between 300K and 1250K and heating and cooling rates of 250K/min and 10K/min. The two best alloys were an iron-chromium-aluminum alloy and a palladium base alloy. Although significant progress was made, it was concluded that a considerable additional effort would be needed to fully optimize and evaluate these candidate systems.

Hulse, C. O.↗