Search NASA⌕ Search

SEARCH · Search NASA

Results for “lab”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Rust Contamination from Water Leaks in the Cosmic Dust Lab and Lunar and Meteorite Thin Sections Labs at Johnson Space Center

On the early morning of September 15th, 2016, on the first floor of Building 31 at NASA-Johnson Space Center, the hose from a water chiller ruptured and began spraying water onto the floor. The water had been circulating though old metal pipes, and the leaked water contained rust-colored particulates. The water flooded much of the western wing of the building's ground floor before the leak was stopped, and it left behind a residue of rust across the floor, most notably in the Apollo and Meteorite Thin Section Labs and Sample Preparation Lab. No samples were damaged in the event, and the affected facilities are in the process of remediation. At the beginning of 2016, a separate leak occurred in the Cosmic Dust Lab, located in the same building. In that lab, a water leak occurred at the bottom of the sink used to clean the lab's tools and containers with ultra-pure water. Over years of use, the ultra-pure water eroded the metal sink piping and leaked water onto the inside of the lab's flow bench. This water also left behind a film of rusty material. The material was cleaned up and the metal piping was replaced with PVC pipe and sealed with Teflon plumber's tape. Samples of the rust detritus were collected from both incidents. These samples were imaged and analyzed to determine their chemical and mineralogical compositions. The purpose of these analyses is to document the nature of the detritus for future reference in the unlikely event that these materials occur as contaminants in the Cosmic Dust samples or Apollo or Meteorite thin sections.

Kent, J. J.↗

Microbial Monitoring of Astromaterials Curation Labs Reveals Inter-Lab Diversity

The Astromaterials Curation Division at NASA’s Johnson Space Center houses seven sample collections stored in separate clean rooms to avoid cross-contamination. Prior to receiving new sample collections from carbon rich asteroids, we instituted a monitoring program to characterize the microbial ecology of these labs and to understand how organisms could interact with and potentially contaminate current and future collections. Methods: Beginning in Oct. 2017 we sampled the Meteorite (ISO 7 equivalent) and Pristine Lunar (ISO 5 equivalent) labs on a monthly basis. Surface samples were collected using dry swabs. Air samples were collected using an impactor style air sampler. Cultivable organisms were identified and characterized. Aliquots of each sample were also preserved for DNA sequencing. For each sampling event recovery rate was calculated as the percentage of samples showing microbial growth1. Fungal colonies were selected for amino acid extraction and analysis via Ultra- Performance Liquid Chromatography with Fluorescence Detection and Mass Spectrometry.

Regberg, A. B.↗

Micron2 Lab: Microfluidic Microbiology Lab Project

Microbial monitoring during spaceflight is crucial to maintain crew health and ensure water purifications systems are functioning properly. Current protocols for in-flight enumeration of bacteria in potable water systems require culture based methods. In this project, we aim to develop a flight- and microgravity-compatible flow cytometer capable of counting total microbial counts in the water supply and differentiating live from dead bacteria.

Burton, Aaron↗

Spaceport Processing System Development Lab

The Spaceport Processing System Development Lab (SPSDL), developed and maintained by the Systems Hardware and Engineering Branch (NE-C4), is a development lab with its own private/restricted networks. A private/restricted network is a network with restricted or no communication with other networks. This allows users from different groups to work on their own projects in their own configured environment without interfering with others utilizing their resources in the lab. The different networks being used in the lab have no way to talk with each other due to the way they are configured, so how a user configures his software, operating system, or the equipment doesn't interfere or carry over on any of the other networks in the lab. The SPSDL is available for any project in KSC that is in need of a lab environment. My job in the SPSDL was to assist in maintaining the lab to make sure it's accessible for users. This includes, but is not limited to, making sure the computers in the lab are properly running and patched with updated hardware/software. In addition to this, I also was to assist users who had issues in utilizing the resources in the lab, which may include helping to configure a restricted network for their own environment. All of this was to ensure workers were able to use the SPSDL to work on their projects without difficulty which would in turn, benefit the work done throughout KSC. When I wasn't working in the SPSDL, I would instead help other coworkers with smaller tasks which included, but wasn't limited to, the proper disposal, moving of, or search for essential equipment. I also, during the free time I had, used NASA's resources to increase my knowledge and skills in a variety of subjects related to my major as a computer engineer, particularly in UNIX, Networking, and Embedded Systems.

Systems Engineering↗

Dissemination of information about the technologies of the Vision Research Lab through the World Wide Web

The Vision Research Lab at NASA John Glenn Research Center is headed by Dr. Rafat Ansari. Dr. Ansari and other researchers have developed technologies that primarily use laser and fiber optics to non-invasively detect different ailments and diseases of the eye. One of my goals as a LERCIP intern and ACCESS scholar for the 2004 summer is to inform other NASA employees, researchers and the general public about these technologies through the development of a website. The website incorporates the theme that the eye is a window to the body. Thus by investigating the processes of the eye, we can better understand and diagnosis different ailments and diseases. These ailments occur in not only earth bound humans, but astronauts as well as a result of exposure to elevated levels of radiation and microgravity conditions. Thus the technologies being developed at the Vision Research Lab are invaluable to humans on Earth in addition to those astronauts in space. One of my first goals was to research the technologies being developed at the lab. The first several days were spent immersing myself in the various articles, journals and reports about the theories behind Dynamic Light Scattering, Laser Doppler Flowmetry, Autofluoresence, Raman Spectroscopy, Polarimetry and Oximetry. Interviews with the other researchers proved invaluable to help understand these theories as well gain hands on experience with the devices being developed using these technologies. The rest of the Vision Research Team and I sat down and discussed how the overall website should be presented. Combining this information with the knowledge of the theories and applications of the hardware being developed, I worked out different ideas to present this information. I quickly learned Paint Shop Pro 8 and FrontPage 2002, as well as using online tutorials and other resources to help design an effective website. The Vision Research Lab website incorporates the anatomy and physiology of the eye, different diseases that affect the eye and the technologies being develop at the lab to help diagnosis these diseases. It also includes background information on Dr. Ansari as well as other researchers involved in the lab and it includes segments on patents, awards and achievements. There are links to help viewers navigate to internal and external websites to further investigate different ideas and hrther understand the implications of these technologies at being developed.

Dorais, Christopher M.↗

Commerce Lab - An enabling facility and test bed for commercial flight opportunities

Commerce Lab is conceived as an adjunct to the National Space Transportation System (NSTS) by providing a focal point for commercial missions which could utilize existing NSTS carrier and resource capabilities for on-orbit experimentation in the microgravity sciences. In this context, the Commerce Lab provides an enabling facility and test bed for commercial flight opportunities. Commerce Lab program activities to date have focused on mission planning for private sector involvement in the space program to facilitate the commercial exploitation of the microgravity environment for materials processing research and development. It is expected that Commerce Lab will provide a logical transition between currently planned NSTS missions and future microgravity science and commercial R&D missions centered around the Space Station. The present study identifies candidate Commerce Lab flight experiments and their development status and projects a mission traffic model that can be used in commercial mission planning.

Robertson, Jack↗

Experiences with Lab-on-a-chip Technology in Support of NASA Supported Research

Under the auspices of the Microgravity Sciences and Application Department at Marshall Space Flight Center, we have custom designed and fabricated a lab-on-a-chip (LOC) device, along with Caliper Technologies, for macromolecular crystal growth. The chip has been designed to deliver specified proportions of up-to five various constituents to one of two growth wells (on-chip) for crystal growth. To date, we have grown crystals of thaumatin, glucose isomerase and appoferitin on the chip. The LOC approach offered many advantages that rendered it highly suitable for space based hardware to perform crystal growth on the International Space Station. The same hardware that was utilized for the crystal growth investigations, has also been used by researchers at Glenn Research Center to investigate aspects of microfluidic phenomenon associated with two-phase flow. Additionally, our LOCAD (Lab-on-a-chip Application Development) team has lent its support to Johnson Space Center s Modular Assay for Solar System Exploration project. At present, the LOCAD team is working on the design and build of a unique lab-on-a-chip breadboard control unit whose function is not commercially available. The breadboard can be used as a test bed for the development of chip size labs for environmental monitoring, crew health monitoring assays, extended flight pharmacological preparations, and many more areas. This unique control unit will be configured for local use and/or remote operation, via the Internet, by other NASA centers. The lab-on-a-chip control unit is being developed with the primary goal of meeting Agency level strategic goals.

Monaco, Lisa↗

Rocket Lab Venus - Enabling Low-Cost Interplanetary Missions

Rocket Lab’s mission to Venus [1], launching in January 2025, aims to demonstrate that small launch vehicles, such as Electron, and high-energy small spacecraft, such as Photon, can enable a new paradigm of regular, low-cost interplanetary missions. The Electron launch vehicle will deliver the Photon spacecraft carrying the entry probe into low earth orbit, at which point Photon will take over and put both itself and the attached probe on an Earth-Venus transfer trajectory, with assistance from a Lunar flyby. The primary science objective of the mission is to sample the Venusian cloud layers between atitudes of 45 and 60 km above the surface with an autofluorescing nephelometer. The ~1kg scientific instrument will be carried by a small ~17 kg direct entry probe which will separate from the Photon spacecraft approximately 30 minutes prior to atmospheric entry. The probe outer mould line is a scaled down version of the Deep Space 2 probes [2]. NASA’s newly developed 3D Woven Carbon Phenolic, a derivative of the Heatshield for Extreme Entry Environment Technology (HEEET) material [3], is an enabling technology for this mission, and it will comprise the probe forebody heat shield.The probe will communicate directly back to the Earth during its descent via a small on-board radio frequency (RF) antenna. The hyperbolic Venus encounter will see the probe enter the Venusia atmosphere at approximately 11 km/s with an entry flight path angle (EFPA) of about 10°. This relatively low entry angle was selected to increase the duration of the descent phase, reduce the peak deceleration, and reduce the sensitivity of the nominal entry environments to navigational errors. For reference, the Pioneer Venus probes entered at EFPAs varying from about 25° to 70°, resulting in peak decelerations between around 220 and 450 g’s and peak stagnation point heat fluxes ranging from about 40 to 75 MW/m2 [4]. In comparison, the Rocket Lab Venus probe will experience a lower preak deceleration of around 60 g’s and a lower peak stagnation point heat flux of about 15 MW/m2, at the cost of a greater total heat load and correspondingly higher thermal protection system (TPS) mass fraction. This paper recounts the development history of the TPS for the Rocket Lab Venus probe, with a focus on the unique requirements of the mission. In particular, the effect on the TPS design of the mission’s tight budget, short development timeline, slim mass and RF link margins, and mild but long duration entry heating. Rocket Lab’s initial investigations into a ‘hybrid’ TPS [5] based on a scaled version of the Pioneer Venus full-density carbon phenolic forebody shield, and the abandonment of this approach in favour of NASA’s 3D Woven Carbon Phenolic is presented. Additionally, the leveraging of previous testing under the HEEET project at higher conditions and the associated TPS margining strategy that was adopted to avoid the need for extensive mission-specific arc jet testing is discussed. Finally, this paper concludes with a brief consideration of the feasibility of a future low-cost aerocapture technology demonstrator mission based on the 2025 Rocket Lab Venus mission and entry probe.

Lyle Campbell↗

Commerce Lab - A program of commercial flight opportunities

Commerce Lab is conceived as an adjunct to the National Space Transportation System (NSTS) by providing a focal point for commercial missions which could utilize existing NSTS carrier and resource capabilities for on-orbit experimentation in the microgravity sciences. In this context, the Commerce Lab program provides mission planning for private sector involvement in the space program, in general, and the commercial exploitation of the microgravity environment for materials processing research and development. It is expected that Commerce Lab will provide a logical transition between currently planned NSTS missions and future microgravity science and commercial R&D missions centered around the Space Station. The present study identifies candidate Commerce Lab flight experiments and their development status and projects a mission traffic model that can be used in commercial mission planning.

Robertson, J.↗

Virtual Reality Lab Assistant

Virtual Reality Lab Assistant (VRLA) demonstration model is aligned for engineering and material science experiments to be performed by undergraduate and graduate students in the course as a pre-lab simulation experience. This will help students to get a preview of how to use the lab equipment and run experiments without using the lab hardware/software equipment. The quality of the time available for laboratory experiments can be significantly improved through the use of virtual reality technology.

Saha, Hrishikesh↗

Pion and Kaon Lab Frame Differential Cross Sections for Intermediate Energy Nucleus-Nucleus Collisions

Space radiation transport codes require accurate models for hadron production in intermediate energy nucleus-nucleus collisions. Codes require cross sections to be written in terms of lab frame variables and it is important to be able to verify models against experimental data in the lab frame. Several models are compared to lab frame data. It is found that models based on algebraic parameterizations are unable to describe intermediate energy differential cross section data. However, simple thermal model parameterizations, when appropriately transformed from the center of momentum to the lab frame, are able to account for the data.

Norbury, John W.↗

Integration of MSFC Usability Lab with Usability Testing

As part of the Stage Analysis Branch, human factors engineering plays an important role in relating humans to the systems of hardware and structure designs of the new launch vehicle. While many branches are involved in the technical aspects of creating a launch vehicle, human factors connects humans to the scientific systems with the goal of improving operational performance and safety while reducing operational error and damage to the hardware. Human factors engineers use physical and computerized models to visualize possible areas for improvements to ensure human accessibility to components requiring maintenance and that the necessary maintenance activities can be accomplished with minimal risks to human and hardware. Many methods of testing are used to fulfill this goal, such as physical mockups, computerized visualization, and usability testing. In this analysis, a usability test is conducted to test how usable a website is to users who are and are not familiar with it. The testing is performed using participants and Morae software to record and analyze the results. This analysis will be a preliminary test of the usability lab in preparation for use in new spacecraft programs, NASA Enterprise, or other NASA websites. The usability lab project is divided into two parts: integration of the usability lab and a preliminary test of the usability lab.

Cheng, Yiwei↗

Generalized Nanosatellite Avionics Testbed Lab

The Generalized Nanosatellite Avionics Testbed (G-NAT) lab at NASA Ames Research Center provides a flexible, easily accessible platform for developing hardware and software for advanced small spacecraft. A collaboration between the Mission Design Division and the Intelligent Systems Division, the objective of the lab is to provide testing data and general test protocols for advanced sensors, actuators, and processors for CubeSat-class spacecraft. By developing test schemes for advanced components outside of the standard mission lifecycle, the lab is able to help reduce the risk carried by advanced nanosatellite or CubeSat missions. Such missions are often allocated very little time for testing, and too often the test facilities must be custom-built for the needs of the mission at hand. The G-NAT lab helps to eliminate these problems by providing an existing suite of testbeds that combines easily accessible, commercial-offthe- shelf (COTS) processors with a collection of existing sensors and actuators.

Testing data and general test protocols↗

The Lunar Lab Initiative

Analogous to terrestrial Antarctic basecamps at our south pole, space exploration outposts will be a combination of habitation and science-focused assets. The Artemis Exploration Roadmap endeavors to establish a sustained human presence on the lunar south pole starting in 2028. Within the planned Artemis Base Camp, most efforts to date have focused on the habitation assets or a mixture of science and habitation assets . With the recent advent of commercial lunar landing capabilities, the trade space can be further expanded to include dedicated science focused assets that ensure adequate science capability. To that end, the Forge, an innovation team initiative created at the Johnson Space Center (JSC), explored alternative ways to increase the science capabilities within the basecamp. The Forge uses structured brainstorming and facilitation to increase innovation within the assigned team, while executing its process in a rapid turnaround fashion for ideation and design study. As a pilot study for the Forge, a multi-disciplinary team investigated a lunar lab module to augment the lunar surface plans for Artemis. This formulation study evaluated the scientific and operational considerations for this dedicated crew space that would increase the capabilities of lunar surface science operations. The trade space evaluated single lunar lander delivery versus multiple lunar lander delivery for module assembly, alternative structural designs, the science instrument outfitting with mapping to scientific goals to maximize lunar science objectives, and how the lab would be operated. The lab operations options explored a stand-alone facility, as well as a facility integrated into a larger lunar surface complex, while evaluating crew usage and habitability considerations. The resulting alternatives were evaluated by the Forge team with a set of metrics to determine their originality, feasibility, and science performance, and thereby provide a recommendation to the lunar architecture planning team. Lessons learned from the lunar lab study were compiled to improve the process and tools for future Forge studies. Forward work, open issues, and challenges to further refine the design of the various science-focused asset options were also documented. By providing a robust science capability at humanity’s furthest outpost, we can plan for a sustained human lunar presence once the initial lunar surface access capability is well established.

Lunar outpost↗

NASA JSC’s Simulant Development Lab Capabilities and Artemis Testing

The Simulant Development Lab (SDL) is a multifunctional collaborative workspace that supports the development, curation, analysis, testing, and distribution of planetary regolith simulants – including lunar, Martian, asteroidal, and other granular materials. The lab provides a multidisciplinary setting for scientific characterization of simulant physical properties and for engineering evaluations conducted with simulant test beds. To enable this work, the SDL curates and maintains a stock of more than 35 metric tons of simulant material. To evaluate these materials and support testing goals, the lab is equipped with a comprehensive suite of processing tools and analytical instruments. These capabilities enable the SDL’s mission at NASA’s Johnson Space Center to distribute, develop, process, characterize, and test regolith simulants for mission relevant applications. Through controlled and repeatable testing environments that replicate the physical and compositional properties of lunar regolith, the SDL supports Artemis hardware maturation, providing safe, Earth‑based analogs for evaluating systems that must withstand regolith dust interactions, physical wear and abrasion, and operational loads. The facility’s extensive simulant inventory and integrated geological and engineering test infrastructure accelerate technology readiness for Artemis and future exploration campaigns (e.g., future crewed or robotic missions to Mars).

Simulant Development Lab↗

Using hypermedia to develop an intelligent tutorial/diagnostic system for the Space Shuttle Main Engine Controller Lab

This is a tutorial/diagnostic system for training personnel in the use of the Space Shuttle Main Engine Controller (SSMEC) Simulation Lab. It also provides a diagnostic capable of isolating lab failures at least to the major lab component. The system was implemented using Hypercard, which is an program of hypermedia running on Apple Macintosh computers. Hypercard proved to be a viable platform for the development and use of sophisticated tutorial systems and moderately capable diagnostic systems. This tutorial/diagnostic system uses the basic Hypercard tools to provide the tutorial. The diagnostic part of the system uses a simple interpreter written in the Hypercard language (Hypertalk) to implement the backward chaining rule based logic commonly found in diagnostic systems using Prolog. Some of the advantages of Hypercard in developing this type of system include sophisticated graphics, animation, sound and voice capabilities, its ability as a hypermedia tool, and its ability to include digitized pictures. The major disadvantage is the slow execution time for evaluation of rules (due to the interpretive processing of the language). Other disadvantages include the limitation on the size of the cards, that color is not supported, that it does not support grey scale graphics, and its lack of selectable fonts for text fields.

Oreilly, Daniel↗