SEARCH · Search NASA

Results for “layered intermediate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS2000

Observations of an Intermediate Layer During the Coqui II Campaign

NASA sounding rocket 21.114, launched March 7, 1998, during the Coqui II campaign, provided neutral wind and plasma density measurements of a weak intermediate layer. The layer was centered near 140 km and had an approximate peak plasma density of 2200 cc. The measured winds were typically less than 40 m/s, in agreement with wind shear formation theory and coincident density observations. The data obtained during the flight allow us to explore the plasma density structure and wind field morphology of the intermediate layer. Coupled with simultaneous data from Arecibo Observatory, the upleg and downleg density profiles provide three spatially separated measurements that enable the first detailed investigation of the horizontal extent and variation of an intermediate layer.

Bishop, R. L.↗

NASA NTRS1981

Observations of the Ca/+/ twilight airglow from intermediate layers of ionization

Optical and incoherent scatter radar techniques are applied to detect the presence of Ca(+) in lower thermospheric intermediate layers over Arecibo. The Arecibo 430 MHz radar is used to measure electron densities, and the altitude distribution and density of the calcium ion is inferred from the variation of twilight resonant scattering with solar depression angle. Ca(+) and electron column densities are compared, and results indicate that the composition of low-altitude intermediate layers is 2% Ca(+), which is consistent with rocket mass spectrometer measurements. Fe(+) and Mg(+) ultraviolet resonance lines are not detected from the ground due to ozone absorbing all radiation short of 3000 A, and measurements of the neutral iron resonance line at 3860 A show that an atmospheric continuum may result in overestimations of emission rates at high solar depression angles.

Tepley, C. A.↗

NASA NTRS2009

Hypervelocity Impact Performance of Open Cell Foam Core Sandwich Panel Structures

Metallic foams are a relatively new class of materials with low density and novel physical, mechanical, thermal, electrical and acoustic properties. Although incompletely characterized, they offer comparable mechanical performance to traditional spacecraft structural materials (i.e. honeycomb sandwich panels) without detrimental through-thickness channeling cells. There are two competing types of metallic foams: open cell and closed cell. Open cell foams are considered the more promising technology due to their lower weight and higher degree of homogeneity. Leading micrometeoroid and orbital debris shields (MMOD) incorporate thin plates separated by a void space (i.e. Whipple shield). Inclusion of intermediate fabric layers, or multiple bumper plates have led to significant performance enhancements, yet these shields require additional non-ballistic mass for installation (fasteners, supports, etc.) that can consume up to 35% of the total shield weight [1]. Structural panels, such as open cell foam core sandwich panels, that are also capable of providing sufficient MMOD protection, represent a significant potential for increased efficiency in hypervelocity impact shielding from a systems perspective through a reduction in required non-ballistic mass. In this paper, the results of an extensive impact test program on aluminum foam core sandwich panels are reported. The effect of pore density, and core thickness on shielding performance have been evaluated over impact velocities ranging from 2.2 - 9.3 km/s at various angles. A number of additional tests on alternate sandwich panel configurations of comparable-weight have also been performed, including aluminum honeycomb sandwich panels (see Figure 1), Nomex honeycomb core sandwich panels, and 3D aluminum honeycomb sandwich panels. A total of 70 hypervelocity impact tests are reported, from which an empirical ballistic limit equation (BLE) has been derived. The BLE is in the standard form suitable for implementation in risk analysis software, and includes the effect of panel thickness, core density, and facesheet material properties. A comparison between the shielding performance of foam core sandwich panel structures and common MMOD shielding configurations is made for both conservative (additional 35% non-ballistic mass) and optimistic (additional mass equal to 30% of bumper mass) considerations. Suggestions to improve the shielding performance of foam core sandwich panels are made, including the use of outer mesh layers, intermediate fabric/composite layers, and varying pore density.

Ryan, Shannon↗

NASA NTRS1984

Schottky-Barrier Photocell With Intermediate Metal Layer

Device output and durability increased. Photosensitive GaAs Schottkybarrier device modified by addition of intermediate layer of refractory or alkaline earth metal. Photovoltaic cells and photosensors made with new design put out higher short-circuit currents and better able to withstand rigors of handling and connection to other circuit components.

Alcorn, G. E.↗

NASA NTRS2004

Multilayer Article Characterized by Low Coefficient of Thermal Expansion Outer Layer

A multilayer article comprises a substrate comprising a ceramic or a silicon-containing metal alloy. The ceramic is a Si-containing ceramic or an oxide ceramic with or without silicon. An outer layer overlies the substrate and at least one intermediate layer is located between the outer layer and thc substrate. An optional bond layer is disposed between thc 1 least one intermediate layer and thc substrate. The at least one intermediate layer may comprise an optional chemical barrier layer adjacent the outer layer, a mullite-containing layer and an optional chemical barrier layer adjacent to the bond layer or substrate. The outer layer comprises a compound having a low coefficient of thermal expansion selected from one of the following systems: rare earth (RE) silicates; at least one of hafnia and hafnia-containing composite oxides; zirconia-containing composite oxides and combinations thereof.

Kang N Lee↗

NASA NTRS2005

Stripline/Microstrip Transition in Multilayer Circuit Board

A stripline-to-microstrip transition has been incorporated into a multilayer circuit board that supports a distributed solid-state microwave power amplifier, for the purpose of coupling the microwave signal from a buried-layer stripline to a top-layer microstrip. The design of the transition could be adapted to multilayer circuit boards in such products as cellular telephones (for connecting between circuit-board signal lines and antennas), transmitters for Earth/satellite communication systems, and computer mother boards (if processor speeds increase into the range of tens of gigahertz). The transition is designed to satisfy the following requirements in addition to the basic coupling requirement described above: (1) The transition must traverse multiple layers, including intermediate layers that contain DC circuitry. (2) The transition must work at a frequency of 32 GHz with low loss and low reflection. (3) The power delivered by the transition to top-layer microstrip must be split equally in opposite directions along the microstrip. Referring to the figure, this amounts to a requirement that when power is supplied to input port 1, equal amounts of power flow through output ports 2 and 3. (4) The signal-line via that is necessarily a part of such a transition must not be what is known in the art as a blind via; that is, it must span the entire thickness of the circuit board.

Epp, Larry↗

NASA NTRS2003

Microscope Cells Containing Multiple Micromachined Wells

Tech Briefs, May 2003 19 Manufacturing Microscope Cells Containing Multiple Micromachined Wells The cost per cell has been reduced substantially. John H. Glenn Research Center, Cleveland, Ohio An improved design for multiple-well microscope cells and an associated improved method of fabricating them have been devised. [As used here, "well" denotes a cavity that has a volume of about 1 or 2 L and that is used to hold a sample for examination under a microscope. As used here, "cell" denotes a laminate, based on a standard 1- by 3-in. (2.54- by 7.62-cm) microscope slide, that comprises (1) the slide as the lower layer, (2) an intermediate layer that contains holes that serve as the wells, and (3) a top layer that either consists of, or is similar to, a standard microscope-slide cover slip.] The improved design and method of fabrication make it possible to increase (relative to a prior design and method of fabrication) the number of wells per cell while reducing the fabrication loss and reducing the cost per cell to about one-tenth of the prior value. In the prior design and method, the slide, well, and cover-slip layers were made from silicate glass. The fabrication of each cell was a labor-intensive process that included precise cutting and grinding of the glass components, fusing of the glass components, and then more grinding and polishing to obtain desired dimensions. Cells of the prior design were expensive and fragile, the rate of loss in fabrication was high, and the nature of the glass made it difficult to increase the number of cells per well. Efforts to execute alternative prior designs in plastic have not yielded satisfactory results because, for typical applications, plastics are not sufficiently thermally or chemically stable, not sufficiently optically clear, and/or not hard enough to resist scratching. The figure depicts a cell of the present improved type. The slide and cover-slip layers are made of a low-thermal-expansion glass (Pyrex(TradeMark) or equivalent) and the intermediate (well layer) is made of SiO2 - a combination of materials that results in a laminate stronger than one made from layers of silicate glass. Before the layers are assembled into the laminate, the SiO2 layer is micromachined to form the wells plus shallow grooves that, when subsequently covered with the cover slip, become capillary channels that are used to fill the wells with samples. The micromachining is accomplished by use of the same patterning and etching techniques used to fabricate microelectromechanical systems (MEMS).

Turner, Walter↗

NASA NTRS1993

Advanced reinforcement systems for intermetallic applications

A 2-D axisymmetric model was employed to determine the magnitude of the radial, axial, and hoop stresses caused by the thermal expansion difference between fiber and matrix and which result from the fabrication temperature cycle. Finite element analysis was conducted for single fiber model systems based on SCS-6/Ti3Al+Nb and Al2O3/NiAl. The stress distribution due to the imposition of a graded intermediate layer for each system was determined and included variables of layer thickness and gradation in interlayer chemistry in order to vary the expansion gradient between fiber and matrix. Thermal cycling tests were conducted on sputter coated SCS-6 fibers selectively coated with Ti3Al+Nb, with and without an intermediate layer. Cracking of the Ti3Al+Nb layers was prevented by an interlayer based on Ti-TiN-Ti. The interlayer thickness appeared critical to its efficiency. Similarly, for the case of Al2O3/NiAl, an intermediate layer consisting of a Ni bond coat on the sapphire fiber followed by a graded Al2O3-NiAl layer did not crack when given a thermal excursion to 1100 C and then cooled to room temperature. Acoustic emission tests on single fiber specimens were unsuccessful in detecting load drops associated with the successive fracture of the fiber. For the SCS-6/Ti3Al system this was the result of several factors which included the matrix/fiber ratio and poor bonding of the matrix and fiber. In the case of the Al2O3/NiAl system brittle failure of the NiAl matrix precluded fiber breakdown during tensile loading.

Merrick, Howard F.↗

NASA NTRS1972

Lunar properties from transient and steady magnetic field measurements.

The electrical conductivity of the lunar interior has been determined from magnetic field step transients measured on the lunar dark side. The simplest model which best fits the data is a spherically symmetric three layer model having a nonconducting outer crust, an intermediate layer with electrical conductivity of .00035 mhos/m, and an inner core with conductivity of .01 mhos/m. Temperatures calculated from these conductivities in the three regions for an example of an olivine moon are as follows: crust, below 440 K; intermediate layer, 890 K; and core, 1240 K. The whole-moon relative permeability has been calculated from the measurements to be 1.03 plus or minus 0.13.

Dyal, P.↗

NASA NTRS1989

Monolithic III-V/Silicon Spatial Light Modulator

Current techniques for growth of device-quality GaAs on silicon substrates enables fabrication of silicon-based version of photodiode-coupled spatial light modulator. Monolithic photodiode-coupled light-modulator array constructed on silicon substrate by growing InAs/GaAs multiple-quantum-wells over silicon PIN diode layer. Intermediate GaAs buffer layer confines attice-misfit dislocations to vicinity of silicon. Use of silicon makes available wider range of auxiliary on-chip signal-processing circuitry for coding and decoding of data, addition or subtraction of brightness levels, spatial reformatting, and rescaling.

Maserjian, Joseph↗

NASA NTRS2008

Solid-State High-Temperature Power Cells

All-solid-state electrochemical power cells have been fabricated and tested in a continuing effort to develop batteries for instruments for use in environments as hot as 500 C. Batteries of this type are needed for exploration of Venus, and could be used on Earth for such applications as measuring physical and chemical conditions in geothermal and oil wells, processing furnaces, and combustion engines. In the state-of-the-art predecessors of the present solid-state power cells, fully packaged molten eutectic salts are used as electrolytes. The molten-salt-based cells can be susceptible to significant amounts of self-discharge and corrosion when used for extended times at elevated temperatures. In contrast, all-solid-state cells such as the present ones are expected to be capable of operating for many days at temperatures up to 500 C, without significant self-discharge. The solid-state cell described here includes a cathode made of FeS2, an electrolyte consisting of a crystalline solid solution of equimolar amounts of Li3PO4 and Li4SiO4, and an anode made of an alloy of Li and Si (see figure). The starting material for making the solid electrolyte is a stoichiometric mixture of Li3PO4, SiO2, and Li3CO2. This mixture is ball-milled, then calcined for two hours at a temperature of 1,100 C, then placed in a die atop the cathode material. Next, the layers in the die are squeezed together at a pressure between 60 and 120 MPa for one hour at a temperature of 600 C to form a unitary structure comprising the solid electrolyte and cathode bonded together. Finally, the lithium-alloy anode is pressure-bonded to the solid electrolyte layer, using an intermediate layer of pure lithium. In one test of a cell of this type, a discharge rate of about 1 mA per gram of cathode material was sustained for 72 hours at a temperature of about 460 C. This is about three times the discharge rate required to support some of the longer duration Venus-exploration mission scenarios.

Whitacre, Jay↗

NASA NTRS1977

Preliminary study of cyclic thermal shock resistance of plasma-sprayed zirconium oxide turbine outer air seal shrouds

Several experimental concepts representing potential high pressure turbine seal material systems were subjected to cyclic thermal shock exposures similar to those that might be encountered under severe engine start-up and shut-down sequences. All of the experimental concepts consisted of plasma-sprayed yttria stabilized ZrO2 on the high temperature side of the blade tip seal shroud. Between the ZrO2 and a cooled, dense metal backing, various intermediate layer concepts intended to mitigate thermal stresses were incorporated. Performance was judged on the basis of the number of thermal shock cycles required to cause loss of seal material through spallation. The most effective approach was to include a low modulus, sintered metal pad between the ZrO2 and the metallic backing. It was also found that reducing the density of the ZrO2 layer significantly improved the performance of specimens with plasma-sprayed metal/ceramic composite intermediate layers.

Bill, R. C.↗

NASA NTRS1981

A sputtered zirconia primer for improved thermal shock resistance of plasma-sprayed ceramic turbine seals

It is shown that the application of sputtered Y2O3-stabilized ZrO2 (YSZ) primer in plasma-sprayed YSZ ceramic-coated turbine blades results in an improvement, by a factor of 5-6, in the thermal shock life of specimens with a sprayed, porous, Ni-Cr-Al-Y intermediate layer. Species with and without the primer were found to be able to survive 1000 cycles when the intermediate layer was used, but reduced laminar cracking was observed in the specimen with the primer. It is suggested that the sputtered YZS primer-induced properties are due to (1) more effective wetting and adherence of the plasma-sprayed YZS particles to the primer, and (2) the primer's retardation of impinging, molten plasma sprayed particles solidification rates, which result in a less detrimental residual stress distribution.

Bill, R. C.↗

NASA NTRS1979

Thermal stress analysis of ceramic gas-path seal components for aircraft turbines

Stress and temperature distributions were evaluated numerically for a blade-tip seal system proposed for gas turbine applications. The seal consists of an abradable ceramic layer on metallic backing with intermediate layers between the ceramic layer and metal substrate. The most severe stresses in the seal, as far as failure is concerned, are tensile stresses at the top of the ceramic layer and shear and normal stresses at the layer interfaces. All these stresses reach their maximum values during the deceleration phase of a test engine cycle. A parametric study was carried out to evaluate the influence of various design parameters on these critical stress values. The influences of material properties and geometric parameters of the ceramic, intermediate, and backing layers were investigated. After the parametric study was completed, a seal system was designed which incorporated materials with beneficial elastic and thermal properties in each layer of the seal. An analysis of the proposed seal design shows an appreciable decrease in the magnitude of the maximum critical stresses over those obtained with earlier configurations.

Kennedy, F. E.↗

NASA NTRSDate not supplied

Alternative MMOD Shielding Concepts

The main types of meteoroid and orbital debris (MMOD) shields are single-layer “monolithic” shields, dual-wall “Whipple” shields, and multi-wall shields (“Stuffed Whipple” and “multi-shock” are common types). Aluminum alloys are typically used for the outer bumper layer and for the rear wall of the dual- and multi-wall shields, although carbon-composites are increasingly employed in MMOD shields given their low-mass and high-strength. Ceramic (NextelTM) and KevlarTM fabrics are commonly used for the intermediate layers of Stuffed Whipple shields. The NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) group is continuously working to improve NASA spacecraft MMOD shielding by evaluating new materials and shielding concepts by test and analysis. HVIT has performed many hypervelocity impact tests over several years to evaluate alternative MMOD shield materials and concepts. This paper will provide results of this work in the following areas: (1) Material substitutions to improve radiation and MMOD protection within Stuffed Whipple shields, (2) Metallic and ceramic foam bumper and intermediate layer materials, (3) Self-sealing materials. In the first two areas listed above, the candidate shield materials were tested under similar test conditions and with fixed shield standoff and mass. Damage to the rear wall was quantified and compared to determine the best performing shield materials. In the self-sealing material evaluations, the test objective was to gauge the ability of different materials and techniques to stop leaks in a rear wall with a 1-atmosphere (air) delta-pressure across the wall. This paper provides results of the investigations and describes forward work to continue the development of the most promising MMOD shield alternatives. KevlarTM is a trademark of DuPont de Nemours, Inc. NextelTM is a trademark of 3M Corporation Note, Trade names and trademarks are used in this report for identification only. Their usage does not constitute an official endorsement, either expressed or implied, by the National Aeronautics and Space Administration.

Hypervelocity↗

NASA NTRSDate not supplied

NNREPAIR: Constraint-based Repair of Neural Network Classifiers

We present NNREPAIR, a constraint-based technique for repairing neural network classifiers by i) fixing the logic of the network at an intermediate layer, and ii) fixing the decision conditions of the network at the last layer. NNREPAIR first uses fault localization to find potentially faulty network parameters (specifically weights) and then performs repair using constraint solving to apply small modifications to remedy the defects. We present novel strategies to enable precise yet efficient repair such as inferring correctness specifications to act as oracles for intermediate layer repair, and generation of experts wrt each class. We demonstrate the technique in the context of three different scenarios: (1) Improving the over all accuracy of a model, (2) Fixing security vulnerabilities caused by poisoning of training data and (3) Improving the robustness of the network against adversarial attacks. Our evaluation on MNIST and CIFAR-10 models shows that NNREPAIR can improve the accuracy by 45.56% on poisoned data and 11.11% on adversarial data. NNREPAIR also provides improvement, albeit modest, in the overall accuracy of models, without requiring new data or re-training.

Repair↗

NASA NTRS1985

Solid-state Bonding of Superplastic Aluminum Alloy 7475 Sheet

Experimental works were carried out to study the feasibility of solid state bonding of superplastic aluminum 7475 sheet. Amount of deformation, bonding time, surface cleaning method and intermediate layer were the process parameters investigated. Other parameters, held constant by the superplastic forming condition which is required to obtain a concurrent solid state bonding, are bonding temperature, bonding pressure and atmosphere. Bond integrity was evaluated through metallographic examination, X-ray line scan analysis, SEM fractographic analysis and lap shear tests. The early results of the development program indicated that sound solid state bonding was accomplished for this high strength 7475 alloy with significant amounts of deformation. A thin intermediate layer of the soft 5052 aluminum alloy aided in achieving a solid state bonding by reducing the required amount of plastic deformation at the interface. Bond strength was substantially increased by a post bond heat treatment.

Byun, T. D. S.↗

NASA NTRS2004

Multilayer article having stabilized zirconia outer layer and chemical barrier layer

A multilayer article includes a substrate that includes at least one of a ceramic compound and a Si-containing metal alloy. An outer layer includes stabilized zirconia. Intermediate layers are located between the outer layer and the substrate and include a mullite-containing layer and a chemical barrier layer. The mullite-containing layer includes 1) mullite or 2) mullite and an alkaline earth metal aluminosilicate. The chemical barrier layer is located between the mullite-containing layer and the outer layer. The chemical barrier layer includes at least one of mullite, hafnia, hafnium silicate and rare earth silicate (e.g., at least one of RE.sub.2 SiO.sub.5 and RE.sub.2 Si.sub.2 O.sub.7 where RE is Sc or Yb). The multilayer article is characterized by the combination of the chemical barrier layer and by its lack of a layer consisting essentially of barium strontium aluminosilicate between the mullite-containing layer and the chemical barrier layer. Such a barium strontium aluminosilicate layer may undesirably lead to the formation of a low melting glass or unnecessarily increase the layer thickness with concomitant reduced durability of the multilayer article. In particular, the chemical barrier layer may include at least one of hafnia, hafnium silicate and rare earth silicate.

Lee, Kang N.↗