Search NASA⌕ Search

SEARCH · Search NASA

Results for “lift modulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

A lateral guidance algorithm to reduce the post-aerobraking burn requirements for a lift-modulated orbital transfer vehicle

A lateral guidance algorithm which controls the location of the line of intersection between the actual and desired orbital planes (the hinge line) is developed for the aerobraking phase of a lift-modulated orbital transfer vehicle. The on-board targeting algorithm associated with this lateral guidance algorithm is simple and concise which is very desirable since computation time and space are limited on an on-board flight computer. A variational equation which describes the movement of the hinge line is derived. Simple relationships between the plane error, the desired hinge line position, the position out-of-plane error, and the velocity out-of-plane error are found. A computer simulation is developed to test the lateral guidance algorithm for a variety of operating conditions. The algorithm does reduce the total burn magnitude needed to achieve the desired orbit by allowing the plane correction and perigee-raising burn to be combined in a single maneuver. The algorithm performs well under vacuum perigee dispersions, pot-hole density disturbance, and thick atmospheres. The results for many different operating conditions are presented.

Herman, G. C.↗
NASA NTRS1983

Minimum-fuel aeroassisted coplanar orbit transfer using lift-modulation

Minimum-fuel trajectories and lift controls are computed for aeroassisted coplanar transfer from high orbit to low orbit. The optimal aeroassisted transfer requires less fuel than the all-propulsive Hohmann transfer for a wide range of high orbit to low orbit transfers. The optimal control program for the atmospheric portion of the transfer is to fly at maximum positive L/D initially to recover from the downward plunge, and then, to fly at negative L/D to level off the flight, such that the vehicle skips out of the atmosphere with a flight path angle near zero degrees. To avoid excessive heating rates, the vehicle flies initially at high angle of attack in order to slow down higher in the atmosphere, allowing recovery from the downward plunge, which occurs subsequently using the maximum positive L/D, to take place at a lower atmospheric density, or equivalently, at a higher altitude.

Mease, K. D.↗
NASA NTRS1972

Roll-modulated lifting entry optimization.

Equations of lifting entry are considered for fixed-angle-of-attack vehicular motion with path control for roll modulation of lift. Attention is directed to relocation and its consequences for the fixed-angle-of-attack atmospheric entry problem. Two reduced-order methods for working with the resulting system of equations are briefly examined. The methods are deemed to warrant further study.

Kelley, H. J.↗
NASA NTRS1977

Flight with lift modulation inside a planetary atmosphere

A set of dimensionless variables is introduced to derive the equations for flight with lift and bank modulation inside a planetary atmosphere in a Newtonian gravitational field. Flight subject to constraints on state variables is discussed and a general approach is presented. Two examples are analyzed in detail: flight at constant speed, and flight at constant sinking speed.

Vinh, N. X.↗
NASA NTRS1976

Flight with lift modulation inside a planetary atmosphere

A set of dimensionless variables (modified Chapman's variables) is introduced in a derivation of general equations for lifting flight and bank modulation within a planetary atmosphere. The atmosphere is assumed spherical and at rest, and a generalized lift-drag polar is also introduced. Corresponding equations for flight over a flat planet model are attained via a straightforward transformation. Two planar flight cases: flight at constant absolute speed over a spherical planet, and flight at constant descent rate over a flat planet, are analyzed, and the required lift control law (with negative or positive lift) is exhibited in each case. Glide at very high descent rate and plane flows of trajectories are analyzed.

Vinh, N. X.↗
NASA NTRSDate not supplied

A Crew and Logistics Lander for the Common Habitat Architecture

The Common Habitat Architecture is a conceptual study that explores the use of a large habitat derived from the Space Launch System (SLS) liquid oxygen tank as a core habitation element that can be used for crew missions or training in 0g, 1/6g, 3/8g, and 1g. This is not part of current NASA Artemis mission planning, but instead represents an architecture that could potentially follow after the Artemis missions and initial human Mars landings. This architecture leverages Starship-derived vehicles for crew landing on and ascent from the Moon and Mars in support of long-duration surface missions with pressurized crew transfer baselined as a nominal capability. This is not the Human Landing System variant of Starship but represents a number of modifications to enable long-duration surface missions with an eight-person crew size. A rapid brainstorming study was conducted in February of 2021, using only public data, to identify options to deliver the 90-ton Common Habitat to the surface and emplace it at the intended habitation site. This study compared three lunar lander concepts and three Mars lander concepts before ultimately selecting the SpaceX Starship as the most viable lander. The Common Habitat Architecture assumes that this Starship variant can further be modified for crew and cargo delivery, assuming that the use of a common system will lead to cost benefits. It is assumed that the Starship will expend too much propellant in landing crew and logistics to be able to launch, given the assumed absence of surface propellant production. Consequently, a separable ascent stage is used for crew ascent. The pressurized elements of this modified Starship are discussed: Starship Ascent Module, Airlock, Transfer Tunnel, Pressurized Crew Transfer Module, and Logistics Modules. For each element, a description, dimensions, rough mass estimates, core capabilities, and design features are presented. Key mechanisms and internal structures of the starship are also discussed. This will include flame diverters for the ascend module, the orbital docking hatch, Pressurized Crew Transfer Module Garage door, Starship Ascent Module fairing, flame diverter blow-out panels, Pressurized Crew Transfer Module lift system, logistics module lift system, contingency crew ascent via the logistics module lift system, internal catwalks, and structural interfaces. Concept of Operations will be discussed for both Moon and Mars. This will include in-space crew rendezvous and transfer, crewed landing, shirtsleeve crew transfer, crew departure, contingency surface operations, and final element disposition. Key differences for Mars will be discussed, such as the Martian atmosphere, dust storms, the absence of crew handover, and Deep Space Exploration Vehicle rendezvous. Contingency microgravity maintenance access will also be discussed. This work will demonstrate viable pressurized crew transfer with a Starship-based lander architecture. Forward work includes Garage lighting and camera systems, Starship Ascent Module propulsion system and docking port trades, contingency habitation trades, and mass/power equipment estimation. Finally, forward work includes developing a heavy cargo return system derived from the Crew and Logistics Starship. The goal of this system is the return of at least 10,000 kg payloads from the surfaces of the Moon and Mars.

Lunar Lander↗
NASA NTRS1986

Electromagnetic braking for Mars spacecraft

Aerobraking concepts are being studied to improve performance and cost effectiveness of propulsion systems for Mars landers and Mars interplanetary spacecraft. Access to megawatt power levels (nuclear power coupled to high-storage inductive or capacitive devices) on a manned Mars interplanetary spacecraft may make feasible electromagnetic braking and lift modulation techniques which were previously impractical. Using pulsed microwave and magnetic field technology, potential plasmadynamic braking and hydromagnetic lift modulation techniques have been identified. Entry corridor modulation to reduce loads and heating, to reduce vertical descent rates, and to expand horizontal and lateral landing ranges are possible benefits. In-depth studies are needed to identify specific design concepts for feasibility assessments. Standing wave/plasma sheath interaction techniques appear to be promising. The techniques may require some tailoring of spacecraft external structures and materials. In addition, rapid response guidance and control systems may require the use of structurally embedded sensors coupled to expert systems or to artificial intelligence systems.

Holt, A. C.↗
NASA NTRS1961

Atmosphere Entries with Vehicle Lift-Drag Ratio Modulated to Limit Deceleration and Rate of Deceleration: Vehicles with Maximum Lift-Drag Ratio of 0.5

An analysis has been made of atmosphere entries for which the vehicle lift-drag ratio was modulated to maintain specified maximum decelerations and/or maximum deceleration rates. The part of the vehicle drag polar used during modulation was from maximum lift coefficient to minimum drag coefficient. The entries were at parabolic velocity and the vehicle maximum lift-drag ratio was 0.5. Two-dimensional trajectory calculations were made for a nonrotating, spherical earth with an exponential atmosphere. The results of the analysis indicate that for a given initial flight-path angle, modulation generally resulted in a reduction of the maximum deceleration to 60 percent of the unmodulated value or a reduction of maximum deceleration rate to less than 50 percent of the unmodulated rate. These results were equivalent, for a maximum deceleration of 10 g, to lowering the undershoot boundary 24 miles with a resulting decrease in total convective heating to the stagnation point of 22 percent. However, the maximum convective heating rate was increased 18 percent; the maximum radiative heating rate and total radiative heating were each increased about 10 percent.

Katzen, Elliott D.↗
NASA NTRS2018

Adaptive Deployable Entry Placement Technology (ADEPT) Development for Small Sat Class Venus Missions

The Adaptable, Deployable Entry and Placement Technology (ADEPT) is a novel approach for entry vehicle design. Similar to an umbrella, it is stowed during launch and deployed prior to entry. ADEPT employs a high performance, 3-D woven, carbon fabric to serve as the primary surface of the mechanically deployed system. The successful ADEPT sounding rocket flight test matured the 1-meter Class ADEPT in the areas of deployment and structural integrity, and provided aerodynamic flight characteristics of the ADEPT open-back configuration from Mach 3 to Mach 0.3. Aerocapture uses the aerodynamic drag from a single hyperbolic atmospheric pass to provide the delta-V needed for orbit insertion. Studies suggest that, compared to propulsive orbit insertion, aerocapture could increase delivered payload by 70 percent at Venus. Drag modulation aerocapture, which shows promise of being simpler and more cost-effective than the more-often studied lift modulation methods, uses in-flight transformations of an entry vehicle's drag area to control the amount of deceleration produced during an atmospheric pass. In single-event drag modulation, a drag device is jettisoned after the appropriate deceleration. ADEPT, due to its unique ability to fold and unfold, is being considered for this SmallSat class payload mission applications.

Cassell, Alan M.↗
NASA NTRSDate not supplied

Thermal Protection System to Enable Ice Giant Aerocapture Mission for Delivering Both an Orbiter and an In Situ Probe

The Ice Giants have been identified as high priority science destinations in the last Decadal Survey [1] and could benefit from aerocapture as the primary method for orbit insertion [2]. A mass-efficient aerocapture system will enable the delivery of an orbiter along with an atmospheric probe (for in situ measurements to anchor global data collected by the orbiter) and possibly a lander at Triton [3]. Aerocapture could be executed either using low L/D rigid aeroshell with lift modulation (LMA) [4] or using deployable aeroshell using drag modulation (DMA) [3]. Nearly two decades ago, a NASA-funded team performed Neptune-Triton aerocapture studies with a mid-L/D lifting configuration [5] for achieving orbit using LMA. This study showed aerocapture challenges. Due to very high peak entry conditions combined with very high heat-load, a suite of TPS materials was required and this suite was deemed problematic from a qualification perspective, due test facility limitations. In the past 20 years, progress made in GN&C for lift-guided entry missions such as MSL, Orion EFT1, Mars 2020 and the upcoming Artemis missions, and the expertise in blunt body aerodynamics at large scale (~ 5m) has led the EDL community to conclude that aerocapture is a “go do” engineering activity and most technologies are in hand to propose missions with aerocapture [6] [7]. Aerocapture using DMA, currently in development, is an option for Ice Giant Missions. While DMA is simpler in some sense, due to ballistic entry and no need for lift-guided maneuvering, it has challenges and it’s maturity is lower. LMA and DMA both require one or more ablative Thermal Protection System (TPS) materials for the rigid aeroshell element. The ablative TPS needs to be robust and mass efficient due to the high heat loads and size of the rigid aeroshell. Currently, there are capable ablative thermal protection materials, e.g., Heatshield for Extreme Entry Environments Technology (HEEET), 3-D woven Mid-Density Carbon- Phenolic (3MDCP), and PICA (Phenolic-Impregnated Carbon Ablator) that are mature, i.e., at TRL 6 or higher. NASA also invested in Conformal PICA that was matured to TRL 5. Our goal is to evaluate the applicability of high TRL TPS and consider other design options. We first establish bounding aerocapture trajectories for a wide range of arrival conditions and the associated aerothermal environment. Based on the environments, we then determine the predicted TPS mass for the aeroshell [4]. In this presentation, we will outline the process by which we establish bounding aerocapture trajectories for hyperbolic excess velocities ranging from 27 km/s to 35 km/s, which are shown to be a range of velocities that can reduce the trip time from ~14 years to 8 years. The above velocity range translates to ~12 km/s to ~24 km/s arrival velocities at the planetary entry interface [2]. The velocity reduction required to achieve orbit ranges between ~2.5 km/s to 9.5 km/s for both Neptune and Triton. Propulsive insertion alone, due to the amount of fuel required to achieve the required velocity reduction, limits the science returned [2]. We establish the bounding aerocapture trajectories for a low L/D (~ 0.4) configuration for three different ballistic coefficients. The ballistic coefficient range is determined from three different aeroshell diameters of 3m, 4m and 5m and with an entry system mass of 2200 kg. With the above range of design parameters, we then determine conservative/bounding estimates of aerothermal environments by using a combination of CFD simulations and stagnation point heating estimates [7]. This engineering approach allows us to first assess the TPS need vs. TPS capability and determine the applicability of existing TPS. Once an applicable suite of TPS is determined, the TPS thickness and mass are computed. We show that the TPS mass fraction can be as low as 5% to as high as 20%, depending on total trip time reduction and other design parameters for a range of TPS. This is a large range for TPS mass fraction. We show PICA and HEEET can indeed enable aerocapture missions, but the missions incur a mass penalty. TPS mass savings, can be further reduced with the use of conformal PICA. Advancing the development of Conformal PICA to make it robust across the entire aerothermal environment (peak heat-flux, pressure and shear) range will result in TPS mass fractions of < 10% for Ice Giant aerocapture missions such as the Neptune-Triton mission. Aerocapture allows for not only shortening the trip time but enables larger mass to be placed in orbit. Furthermore, probes deployed from orbit will benefit in reduced entry environments allowing for a lower risk TPS implementation as compared to mission designs where the probe is released prior to orbit insertion. One of the challenges for the Ice Giant community is to ensure mission designs that maximize science and allow flexibility in the placement of the entry probe. The traditional approach to release the probe ahead of the orbiter may not optimize returned science. In this presentation, we will make the case for mature TPS such as HEEET and PICA. While these materials can enable aerocapture missions, completing the development of conformal PICA and extending Conformal PICA to be more robust, will have significant impact to TPS mass efficiency and significantly enhance science return for future Gas- and Ice-Giant missions.

E Venkatapathy↗
NASA NTRS1979

Weight and cost estimating relationships for heavy lift airships

Weight and cost estimating relationships, including additional parameters that influence the cost and performance of heavy-lift airships (HLA), are discussed. Inputs to a closed loop computer program, consisting of useful load, forward speed, lift module positive or negative thrust, and rotors and propellers, are examined. Detail is given to the HLA cost and weight program (HLACW), which computes component weights, vehicle size, buoyancy lift, rotor and propellar thrust, and engine horse power. This program solves the problem of interrelating the different aerostat, rotors, engines and propeller sizes. Six sets of 'default parameters' are left for the operator to change during each computer run enabling slight data manipulation without altering the program.

Gray, D. W.↗
NASA NTRS1980

Trajectories optimization in hypersonic flight

Equations of motion were derived for the three dimensional flight of a lifting vehicles, taking into consideration all the main effects of different forces acting on a vehicle at orbital speeds. A set of equations was formulated which are valid for both the flight with lift modulation inside a planetary atmosphere and the Keplerian motion in the vacuum. The equations are independent of the physical characteristics of the vehicle. The only parameters involved are the maximum lift to drag ratio of the vehicle and a constant characterizing the atmosphere. The results obtained can be applied without modifications to any future reentry vehicle, regardless of its size, shape, and mass.

Vinh, N. X.↗
NASA NTRS1980

Hypersonic and planetary entry flight mechanics

The book treats hypersonic flight trajectories and atmospheric entry flight mechanics in light of their importance for space shuttle entry. Following a review of the structures of planetary atmospheres and aerodynamic forces, equations are derived for flight over a spherical planet, and the performance of long-range hypervelocity vehicles in extra-atmospheric flight is analyzed. Consideration is then given to vehicle trajectories in the powered and atmospheric reentry phases of flight, and several first-order solutions are derived for various planetary entry situations. The second-order theory of Loh for entry trajectories is presented along with the classical theories of Yaroshevskii and Chapman for entry into planetary atmospheres, and the thermal problems encountered in hypersonic flight are analyzed. A unified theory for entry into planetary atmospheres is then introduced which allows the performance of a general type of lifting vehicle to be studied, and applied to the analysis of orbit contraction due to atmospheric drag, flight with lift modulation and lateral maneuvers.

Vinh, N. X.↗