Search NASA⌕ Search

SEARCH · Search NASA

Results for “liquid-metals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Review of experimental investigations of liquid-metal heat transfer

Experimental data of various investigators of liquid-metal heat-transfer characteristics were reevaluated using as consistent assumptions and methods as possible and then compared with each other and with theoretical results. The reevaluated data for both local fully developed and average Nusselt numbers in the turbulent flow region were found still to have considerable spread, with the bulk of the data being lower than predicted by existing analysis. An equation based on empirical grounds which represents most of the fully developed heat-transfer data is nu = 0.625 pe(0.4) where nu represents the Nusselt number and pe the Peclet number. The theoretical prediction of the heat transfer in the entrance region was found to give lower values, in most cases, than those found in the experimental work.

Lubarsky, Bernard↗
NASA NTRS1950

Preliminary analysis of three cycles for nuclear propulsion of aircraft

A preliminary study was made of the feasibility of three cycles for nuclear propulsion of aircraft: a direct-air-turbojet, a binary liquid-metal turbojet, and a helium compressor jet. All three cycles appeared feasible for flight at a Mach number of 0.9 and altitudes up to 50,000 feet; the liquid-metal cycle appeared feasible for flight at a Mach number of 1.5. The air and helium cycles resulted in heavier aircraft than did the liquid-metal cycle, particularly at a Mach number of 1.5. The relative advantage of the liquid-metal cycle became greater as the flight speed and altitude increased, and as the reactor wall temperature decreased.

Humble, L V↗
DOE OSTI2025

Accelerating phase field simulations through a hybrid adaptive Fourier neural operator with U-net backbone

Prolonged contact between a corrosive liquid and metal alloys can cause progressive dealloying. For one such process as liquid-metal dealloying (LMD), phase field models have been developed to understand the mechanisms leading to complex morphologies. However, the LMD governing equations in these models often involve coupled non-linear partial differential equations (PDE), which are challenging to solve numerically. In particular, numerical stiffness in the PDEs requires an extremely refined time step size (on the order of 10 -12 s or smaller). This computational bottleneck is especially problematic when running LMD simulation until a late time horizon is required. This motivates the development of surrogate models capable of leaping forward in time, by skipping several consecutive time steps at-once. In this paper, we propose a U-shaped adaptive Fourier neural operator (U-AFNO), a machine learning (ML) based model inspired by recent advances in neural operator learning. U-AFNO employs U-Nets for extracting and reconstructing local features within the physical fields, and passes the latent space through a vision transformer (ViT) implemented in the Fourier space (AFNO). We use U-AFNOs to learn the dynamics of mapping the field at a current time step into a later time step. We also identify global quantities of interest (QoI) describing the corrosion process (e.g., the deformation of the liquid-metal interface, lost metal, etc.) and show that our proposed U-AFNO model is able to accurately predict the field dynamics, in spite of the chaotic nature of LMD. Most notably, our model reproduces the key microstructure statistics and QoIs with a level of accuracy on par with the high-fidelity numerical solver, while achieving a significant 11, 200 × speed-up on a high-resolution grid when comparing the computational expense per time step. Finally, we also investigate the opportunity of using hybrid simulations, in which we alternate forward leaps in time using the U-AFNO with high-fidelity time stepping. We demonstrate that while advantageous for some surrogate model design choices, our proposed U-AFNO model in fully auto-regressive settings consistently outperforms hybrid schemes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Capability in Theory, Modeling, and Validation for a Range of Innovative Fusion Concepts using High-Fidelity Moment-Kinetic Models

A computational modeling capability is created and available to the fusion community to understand and design lower-cost and innovative fusion concepts. The approach uses high- fidelity kinetic, moment-kinetic, and moment models and includes sophisticated plasma- boundary interactions. A majority of fusion-relevant simulations are performed with magnetohydrodynamic models and hybrid particle-in-cell codes, with limited-fidelity electron and kinetic physics. However, in fusion configurations like Z-pinches, field-reversed- configurations, plasma jet magneto-inertial fusion, spinning mirrors, and others, kinetic effects (both electron and ions) are critical to understand the physics and design scaling into the highly kinetic regime of a burning fusion plasma. Furthermore, as present fusion machines move towards a burning plasma regime, liquid-metal blankets are needed to handle first-wall heat- flux, reduce erosion, and eventually for energy conversion and fuel breeding. The work performed under this ARPA-E BETHE Capability Team advances the state-of-the-art in modeling and understanding plasma dynamics in fusion devices and its coupling with liquid-metal dynamics. These are critical areas of research for fusion energy to become realizable. To address these complex problems, we have leveraged and extended computational capabilities through the code, Gkeyll (developed jointly with Princeton Plasma Physics Laboratory and academic partners), for kinetic and moment modeling of fusion plasmas. The Concept Teams supported by this Capability Team include the Wisconsin High-field Axisymmetric Mirror (WHAM), Centrifugal Mirror Experiment (CFME), Plasma-Jet Magneto- Inertial Fusion (PJMIF), and solid and liquid wall plasma-material interaction studies relevant to a number of fusion concepts including Zap Energy’s Z-pinch. This software is open-source and available to the fusion community as a high-fidelity tool for the design of lower-cost fusion experiments. 3D gyrokinetic simulations of WHAM are now possible for long enough time scales to understand the evolution of interchange instabilities. 3D multi-fluid simulations of CMFE at higher Mach numbers are now possible for detailed design iterations with the goal of stability. The state-of-the-art in understanding shock formation and shock mitigation regimes in merging liners for PJMIF have been furthered by our kinetic simulations. Our novel models and frameworks studying plasma-material interaction by incorporating wall emission for various solid wall materials of relevance to pulsed and steady fusion concepts have advanced the state-of-the-art in our understanding of particle fluxes, heat fluxes, and other quantities at cathodes and anodes. The results from this work may explain discrepancies between experimental and theoretical predictions of achieved current densities in pulsed concepts such as Z-pinches. Another significant contribution of this Capability Team is the development and deployment of a novel experimental platform, LEX (Liquid Electrode eXperiment), at Virginia Tech to understand liquid metal free-surface response to electromagnetic pulses. The novel experiments along with model validation quantified the effect of different materials and sizes of liquid metal droplets on the radiative power balance of fusion plasmas for pulsed concepts. Furthermore, these experiments provided mitigation strategies for violent liquid metal response for high current pulses as would be expected in fusion regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Development of a conduction-based model for analyzing frozen startup of alkali-metal heat pipes

One key area of interest in heat pipe modeling/simulation is to analyze the startup behavior of the liquid-metal heat pipes (LMHPs) from a frozen state. This so-called ‘frozen startup’ process involves a complex set of nonlinear mass and heat transport phenomena, including phase transitions from solid to liquid and vapor, multiphase interactions, microporous wick flow, and compressible vapor dynamics. The complexity of these processes makes it challenging to simulate LMHP’s frozen startup using conventional numerical methods or commercial computational fluid dynamics (CFD) software. This paper presents a simplified conduction-based modeling approach that can provide practical insights into the entire LMHP frozen startup process, while alleviating the challenges of modeling its complex physics. The theoretical foundation and physical assumptions of the proposed model are based solely on heat-conduction equation, allowing for a more tractable simulation without sacrificing essential physical accuracy. The proposed model was implemented in a commercial CFD software, and its prediction was compared with the experimental data obtained from sodium heat-pipe startup experiments. The comparison highlights the proposed model's ability to capture the transient thermal behavior of LMHP during frozen startup. This study not only validates the conduction-based frozen startup modeling method but also shows its potential as a practical and efficient tool for understanding the startup performance of the LMHP systems.

Microreactor↗
DOE OSTI2026

Numerical implementation of the MOOSE subchannel module (SCM) algorithm

The subchannel module of moose (SCM), previously referred to as Pronghorn-SC, is a subchannel code designed to resolve single-phase flow fields and calculate the relevant flow variables, in nuclear reactor fuel-pin assemblies. The assemblies it models are: water-cooled, with bare fuel-pins in a square ducted, quadrilateral lattice and liquid-metal/water-cooled, with bare/wire-wrapped fuel pins in a hexagonal ducted, triangular lattice. Previous publications have presented the development, validation and verification of SCM. This work presents an comparative overview of the different solvers implemented within SCM. This includes the solver algorithm description, and a performance comparison. The two test cases chosen to demonstrate the solver performance were taken from the PSBT enthalpy mixing benchmark and the ORNL-19 pin benchmark.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

A Three-Component Strategy for Synthesizing High-Entropy Alloy Nanoparticles with High-Index Facets

Controlling the shapes and, more importantly, exposed facets (high-index facets (HIFs), especially) of high-entropy alloy (HEA) nanoparticles is not yet possible. Herein, a three-component synthetic strategy for obtaining tetrahexahedral (THH)-shaped HIF-HEA nanoparticles through a combined alloying-dealloying strategy and liquid-metal mediation process is reported. Metal precursors are first alloyed with Ga to form multielemental nanoparticles and then alloyed with a volatile metal. Selectively dealloying the volatile metal from the nanoparticles is used to regulate their surface energies; the Ga stabilizes the HEA phase, and the trace element stabilizes the HIFs, resulting in THH-shaped HEA nanoparticles (seven different types) with {210} HIFs. Finally, nanoparticle megalibraries containing millions of THH-shaped HIF-HEAs on 4 cm 2 chips with size and composition control shows generalizability and scalability for materials discovery purposes.

alloys↗
DOE OSTI2025

Design and Analysis of the Open-Surface Slow Li Flow Divertor and Comparison to the Fast Li Flow Divertor

In the ongoing U.S. project, “Liquid Metal Plasma Facing Components,” sponsored by the U.S. Department of Energy, efforts have been taken to develop two open-surface divertor designs for the Fusion Nuclear Science Facility using liquid lithium (Li) as a heat and particle flux removal media. The main focus of this study is the design and analysis of a slow (~1 mm/s) and thin (<1 mm) open-surface Li flow divertor with a Li-cooled substrate, which is then compared with an earlier design of a fast (up to 10 m/s) and thick (~0.5 cm) Li flow divertor with the substrate cooled with helium. The slow Li flow divertor design is based on the original LiWall concept developed at the Princeton Plasma Physics Laboratory. Such a thin and slow Li layer can remove the particle flux by reducing the recycling flux, while the heat flux is removed mainly through the heat sink located beneath. In the present study, the heat sink is provided through a Li cooling flow inside the substrate of reduced activation ferritic/martensitic steel. By performing a multiphysics analysis with COMSOL that included liquid-metal magnetohydrodynamics (MHD), heat transfer, and structural mechanics, the impact of various factors on the divertor heat removal capability, such as Li flow velocity, MHD effects, and inlet velocity boundary condition, were examined. Based on comparisons of the two divertor designs, it was shown that the fast-flow divertor significantly outperformed the slow-flow design, whose heat removal capability was limited to ~1 to 2 MW/m2.

Jiang, Yuchen [ORNL] (ORCID:0000000283280284)↗
DOE OSTI2025

Durability and Accelerated Aging Test of the Polymeric Mirror-Film Prototype (CRADA Final Report)

The participant is developing a low-cost liquid metal coating for concentrated solar power (CSP) polymeric mirrors. Current CSP technology uses bulky and costly glass mirrors. As a lighter alternative, polymeric mirror film is cheaper than glass mirrors, yet expensive to manufacture. The participant is working to develop a room temperature liquid-metal thin-film deposition technique and CSP polymeric mirror film that will reduce expenditures by 80% and film cost by 50%.

14 SOLAR ENERGY↗
DOE OSTI1992

Nuclear Safety [Vol. 33, No. 4, October-December 1992]

Nuclear Safety is a review journal that covers significant developments in the field of nuclear safety. Its scope includes the analysis and control of hazards associated with nuclear energy, operations involving fissionable materials, and the products of nuclear fission and their effects on the environment. Primary emphasis is on safety in reactor design, construction, and operation; however, the safety aspects of the entire fuel cycle, including fuel fabrication, spent-fuel processing, nuclear waste disposal, handling of radioisotopes, and environmental effects of these operations, are also treated. Table of Contents for this issue follows. GENERAL SAFETY CONSIDERATIONS: 499 Technical Note: Nuclear Regulatory Commission’s Examination Question Bank System, C. L Jensen and N. L. Skinner; 506 Report on the Specialists’ Meeting on Passive and Active Safety Features of Liquid-Metal Fast Breeder Reactors Organized by the International Atomic Energy Agency at Oarai Engineering Centre of Power Reactor and Nuclear Development Corporation, Japan, November 5-7,1991, S. R. Paranjpe; ACCIDENT ANALYSIS: 514 A Review of Hydrogen Production During Melt/Water Interaction in LWRs, D. F. Fletcher, B. D. Turland, and S. P. A. Lawrence; 535 A Review of the U 3 0 8 -Al Reaction as a Potential Heat Source in Research and Test Reactor Accidents, J. L. Snelgrove; CONTROL AND INSTRUMENTATION: 543 Multilevel Interfaces for Power Plant Control Rooms II: A Preliminary Design Space, K. J. Vicente; DESIGN FEATURES: 549 Twenty-Second DOE/NRC Nuclear Air Cleaning and Treatment Conference, R. R. Bellamy, D. W. Moeller, and M. W. First; 562 Book Review: Safety Assessment of Unit 5 (WWER-440/W-213) of the Greifswald Nuclear Power Station, M. H. Fontana; WASTE AND SPENT FUEL MANAGEMENT: 576 Activities Related to Waste and Spent Fuel Management, M. D. Muhlheim and E. G. Silver; OPERATING EXPERIENCES: 586 Analysis of Corrective Actions Applied to Nuclear Power Plant Operations, A. E. Cross; 593 Reactor Shutdown Experience, Compiled by J. W. Cletcher; 596 Operating U.S. Power Reactors, Compiled by M. D. Muhlheim and E. G. Silver; 609 Non-Commercial Power Operating Experience; 614 World Nuclear Performance, Compiled by M. D. Muhlheim; RECENT DEVELOPMENTS: 623 General Administrative Activities, Compiled by M. D. Muhlheim and E. G. Silver; 635 Reports, Standards, and Safety Guides, D. S. Queener; 639 Proposed Rule Changes as of June 30, 1992; ANNOUNCEMENTS: 513 Fourth International Conference on Nuclear Fuel Reprocessing and Waste Management RECOD '94; 585 International Topical Meeting on Advanced Reactors Safety; 622 International Workshop on Implementation of ALARA at Nuclear Power Plants; 648 Short Course on Nuclear Criticality Safety; 648 8th Topical Meeting on Problems in Reactor Physics MEPhi-VOLGA-93; 643 The Authors; 646 Reviewers of Nuclear Safety, Vol. 33

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1959

Experimental Investigation of Gas-Side Performance of a Compact Finned-Tube Heat Exchanger

Heat-transfer and pressure-drop data were obtained experimentally for the gas side of a liquid-metal to air, compact finned-tube heat exchanger. The heat exchanger was fabricated from 0.185-inch Inconel tubing in an inline array. The fins were made of 310 stainless-steel- clad copper with a total thickness of 0.010 inch, and the fin pitch was 15.3 fins per inch. The liquid used as the heating medium was sodium. The heat-exchanger inlet gas temperature was varied from 5100 to 1260 R by burning JP fuel for airflow rates of 0.4 to 10.5 pounds per second corresponding to an approximate Reynolds number range of 300 to 9000. The sodium inlet temperature was held at 1400 R with the exception of a few runs taken at 1700 and 1960 R. The maximum ratio of surface temperature to air bulk temperature was 1.45. Friction-factor data with heat transfer were best represented by a single line when the density and viscosity of Reynolds number were evaluated at the average film temperature. At the lower Reynolds numbers reported, the friction data with heat transfer plotted slightly above the friction data without heat transfer. The density of the friction factor was calculated at the average bulk temperature. Heat-transfer results of this investigation were correlated by evaluating the physical properties of air (specific heat, viscosity, and thermal conductivity) at the film temperature.

Gedeon, Louis↗
NASA NTRS1959

Heat Transfer in a Liquid Metal Flowing Turbulently through a Channel with a Step Function Boundary Temperature

An analytical heat transfer solution is derived and evaluated for the general case of a turbulently flowing liquid metal which suddenly encounters a step-function boundary temperature in a channel system. Local Nusselt moduli, dimensionless mixed-mean fluid temperatures, and arithmetic-mean Nusselt moduli are given as functions of Reynolds and Prandtl moduli and a dimensionless axial-distance modulus. These solutions are compared with known solutions of more specific systems as well as with a set of experimental liquid-metal heat transfer data for a thermal entrance region.

Poppendiek, H. F.↗
NASA NTRS1959

Details of Exact Low Prandtl Number Boundary-Layer Solutions for Forced and For Free Convection

A detailed report is given of exact (numerical) solutions of the laminar-boundary-layer equations for the Prandtl number range appropriate to liquid metals (0.003 to 0.03). Consideration is given to the following situations: (1) forced convection over a flat plate for the conditions of uniform wall temperature and uniform wall heat flux, and (2) free convection over an isothermal vertical plate. Tabulations of the new solutions are given in detail. Results are presented for the heat-transfer and shear-stress characteristics; temperature and velocity distributions are also shown. The heat-transfer results are correlated in terms of dimensionless parameters that vary only slightly over the entire liquid-metal range. Previous analytical and experimental work on low Prandtl number boundary layers is surveyed and compared with the new exact solutions.

Sparrow, E. M.↗
DOE OSTI2025

Multiscale Thermal-hydraulic analysis of the MARVEL micro-reactor using coupled MOOSE Subchannel (SCM) and SAM

MARVEL is a natural-convection-cooled sodium-potassium microreactor that is anticipated to generate 85 kilowatts of thermal energy. It will operate within Idaho National Laboratory’s Transient Reactor Test Facility and is being developed by the DOE Microreactor Program. MARVEL will be used to test microreactor applications, evaluate systems for remote monitoring, and develop autonomous control technologies. A thermal-hydraulic computational model of this facility is a valuable tool to study important transients and calculate the safety limits of the micro-reactor design. For this purpose, the authors have chosen to use a multiscale coupled simulation: SCM for modeling the reactor core and SAM for the reactor’s primary cooling system. SCM is MOOSE physics module for subchannel analysis, which was designed to model single-phase flows through liquid-metal cooled, wire-wrapped fuel pin sub-assemblies, ordered in a triangular lattice. The SCM code was modified to be able to model MARVEL’s unique geometry. SAM is a systems analysis module based on the MOOSE framework. It aims to provide fast-running, whole-plant transient analyses capability with improved-fidelity for various advanced reactor types. The coupling between the two SCM and SAM for MARVEL modeling is done implementing a domain over-lapping approach. The resulting coupled simulation can model transients such as reactor startup/shutdown and provide an intermediate fidelity picture of the temperature field and other variables, in the core. Results for the steady-state simulations are presented in the article as well as flow blockage transient.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

SCM overview & the EBR-II shutdown heat removal tests validation.

Pronghorn is an engineering-scale, coarse-mesh, thermal-hydraulics tool for supporting reactor-core simulations of advanced nuclear reactors. Most of the current efforts in Pronghorn have been devoted in developing porous finite-volume capabilities and adapting closure correlations for coarse-mesh thermal-hydraulics modeling. However, for liquid-metal reactors (LMRs) with wire-wrapped fuel pin assemblies, a pin-level thermal-hydraulic resolution is required for most safety case studies (pin rupture, channel blockage, etc.). For this purpose, a new Subchannel application is developed in MOOSE, which affords the required flow field resolution, while still preserving an engineering-scale approach. This new solver can be natively coupled to Pronghorn and other MOOSE objects to enable full-core, multi-physics, multi-scale engineering studies. This presentation presents the main features of the SCM code and demonstrates a validation case based on the EBR-II SHRT tests.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗