Search NASA⌕ Search

SEARCH · Search NASA

Results for “low temperature heat release (LTHR)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effects of Gasoline Composition and Operating Parameters on the Response of End-Gas Autoignition to Nitric Oxide in a Lean-Burn DI-SI Engine

Lean operation of spark-ignition engines can lead to engine thermal efficiency gains and lower NOx emissions due to reduced combustion temperatures. Yet, lean operation could still face challenges in end-gas autoignition and knock generation due to higher intake pressures and trapped NO in the residual gas. Here, this study evaluates the impact of NO on end-gas autoignition for two gasoline fuels with similar octane rating but different composition: high cycloalkane fuel (HCA) and high olefin fuel (HO). Experiments were performed at stoichiometric and lean (λ = 2) conditions and at two engine speeds of 1400 rpm and 2000 rpm. Accompanying chemical kinetics simulations in CHEMKIN revealed that the mechanisms controlling the effect of NO on autoignition are similar λ = 2 and λ = 1, with NO + HO 2 = NO 2 + OH being the main pathway for enhancing reactivity by promoting low-temperature heat release (LTHR). The compositionally different fuels reacted differently to NO seeding and engine speed, and differences were augmented at λ = 2 compared to λ = 1 as the end-gas autoignition shifted to the low temperature regime. HO, which has inherent low temperature chemistry, was strongly impacted by engine speed at low NO seeding levels, with no noticeable peak of LTHR detected at 2000 rpm. On the other hand, LTHR of HCA was marginally affected by shortened residence time at higher engine speed as NO + HO 2 reaction was not greatly affected by shorter time scales, since HO 2 production was sustained even at 2000 rpm to support OH generation from NO + HO 2 . Contrary to HO, HCA exhibited greater sensitivity to NO seeding, as the increased OH production at higher NO concentrations offset the OH-quenching effect of cyclopentane, which accounts for 28.6% of HCA’s composition. Consequently, a sensitivity analysis revealed that fuels with weak inherent low-temperature chemistry, like HCA, are likely to be more sensitive to variations in NO concentration and charge temperature, whereas fuels with strong low temperature chemistry are more sensitive to variations in end-gas λ and intake pressure.

Energy↗
DOE OSTI2020

Autoignition behavior of gasoline/ethanol blends at engine-relevant conditions

Ethanol is an attractive oxygenate increasingly used for blending with petroleum-derived gasoline yielding beneficial combustion and emissions behavior for a range of internal combustion engine schemes, including stoichiometric spark-ignition and low temperature combustion (LTC). As such, it is important to fundamentally understand the autoignition behavior of gasoline/ethanol blends. This work utilizes a rapid compression machine (RCM) and a homogeneous charge compression ignition (HCCI) engine to experimentally quantify changes in fuel reactivity, through ignition delay times and preliminary heat release, for blends of 0 to 30% vol./vol. into a full boiling range research gasoline (FACE-F). Diluted/stoichiometric and undiluted/fuel-lean conditions are explored covering a wide range of compressed temperatures and pressures relevant to conventional and advanced, gasoline combustion engines. Detailed chemical kinetic modeling is undertaken using a recently updated gasoline surrogate model in conjunction with a five-component surrogate to model the RCM experiments and provide chemical insight into the perturbative effects of ethanol on the autoignition process. The diluted/stoichiometric RCM measurements reveal that within the low-temperature regime ethanol retards first-stage and main ignition delay times, and suppresses both the rates and extents of low-temperature heat release (LTHR), while within the intermediate-temperature regime ethanol only causes slight changes. Good agreement of ignition delay time and preliminary heat release prediction is found between model and experimental results. Sensitivity and flux analyses further show that ethanol blending effects are dominated by the competition between the H-atom abstraction from ethanol and other fuel components by OH radical at low temperatures and by HO 2 radical at intermediate temperatures. These findings are consistent across both fuel loading conditions explored in this study. In addition, when HCCI engine experiments are mapped onto undiluted/lean RCM measurements under a constant combustion phasing scenario, good correspondence between the two apparatuses is observed for LTHR and start of high-temperature heat release. Finally, the current study highlights the importance of characterizing LTHR in predicting fuel behaviors in high-boost/low-temperature engines, and demonstrates that RCM experiments can provide an alternative, and more-efficient avenue for such characterization.

02 PETROLEUM↗
DOE OSTI2021

CFD modeling of pre-spark heat release in a boosted direct-injection spark-ignition engine

Accurate predictions of low-temperature heat release (LTHR) are critical for modeling auto-ignition processes in internal combustion engines. While LTHR is typically obscured by deflagration, extremely late ignition phasing can lead to LTHR prior to the spark, a behavior known as pre-spark heat release (PSHR). In this research, PSHR in a boosted direct-injection spark-ignition engine was studied using 3-D computational fluid dynamics (CFD) and detailed chemical kinetics. The turbulent combustion was modeled via a hybrid approach that incorporates the G-equation model for tracking the turbulent flame front, and the well-stirred reactor model with detailed chemistry for assessing the low-temperature reactions in unburnt gas. Simulations were conducted using Co-Optima alkylate and E30 fuels at operating conditions characterized by different PSHR intensities. The predicted in-cylinder pressure and heat release rate were found to agree well with experiments. It was found the estimate of previous-cycle trapped residuals is of utmost importance for capturing PSHR correctly. A simulation best practice was developed which keeps the detailed chemistry solver active throughout the entire simulation, allowing to track the evolution of intermediate species from one cycle to the next. Following the validation, the dynamics of PSHR were analyzed in detail employing the pressure-temperature (P-T) trajectory framework. It was shown that PSHR correlated with the first-stage ignition delay of the fuel, hence showing close relation to the in-cylinder P-T trajectory and the chemical kinetics. Besides, it was indicated that LTHR is a self-limiting process that has the effect of attenuating the thermal stratification in the combustion chamber. Furthermore, it was observed the occurrence of PSHR caused the P-T trajectory of end-gas to overlap with the negative temperature coefficient region of the fuel’s ignition-delay maps. This effect was more significant in the fuel-rich regions where engine knock tendency would be generally higher, with potential implications on knock control and mitigation.

42 ENGINEERING↗
DOE OSTI2021

Numerical Analysis of Fuel Effects on Advanced Compression Ignition Using a Cooperative Fuel Research Engine Computational Fluid Dynamics Model

Growing environmental concerns and demand for a better fuel economy are driving forces that motivate the research for more advanced engines. Multi-mode combustion strategies have gained attention for their potential to provide high thermal efficiency and low emissions for light-duty applications. These strategies target optimizing the engine performance by correlating different combustion modes to load operating conditions. The extension from boosted spark ignition (SI) mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing the compression ratio and utilizing intake air heating. Further, in order to enable an accurate control of intake charge condition for ACI mode and rapid mode-switches, it is essential to gain fundamental insights into the autoignition process. Within the scope of ACI, homogeneous charge compression ignition (HCCI) mode is of significant interest. It is known for its potential benefits, operation at low fuel consumption, low NOx, and particulate matter (PM) emissions. In the present work, a virtual Cooperative Fuel Research (CFR) engine model is used to analyze fuel effects on ACI combustion. In particular, the effect of fuel octane sensitivity (S) (at constant Research Octane Number (RON)) on autoignition propensity is assessed under beyond-RON (BRON) and beyond-MON (BMON) ACI conditions. The three-dimensional CFR engine computational fluid dynamics (CFD) model employs a finite-rate chemistry approach with a multi-zone binning strategy to capture autoignition. Two binary blends with Research Octane Number (RON) of 90 are chosen for this study: primary reference fuel (PRF) with S = 0 and toluene–heptane (TH) blend with S = 10.8, representing paraffinic and aromatic gasoline surrogates. Reduced mechanisms for these blends are generated from a detailed gasoline surrogate kinetic mechanism. Simulation results with the reduced mechanisms are validated against experimental data from an in-house CFR engine, with respect to in-cylinder pressure, heat release rate, and combustion phasing. Thereafter, the sensitivity of combustion behavior to ACI operating condition (BRON versus BMON), air-fuel ratio (λ = 2 and 3), and engine speed (600 and 900 rpm) is analyzed for both fuels. It is shown that the sensitivity of a fuel’s autoignition characteristics to λ and engine speed significantly differs at BRON and BMON conditions. Moreover, this sensitivity is found to vary among fuels, despite the same RON. It is also observed that the presence of low-temperature heat release (LTHR) under BRON condition leads to more sequential autoignition and longer combustion duration than BMON condition. Finally, the study indicates that the octane index (OI) fails to capture the trend in the variation of autoignition propensity with S under the BMON condition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Prospects and Limitations of Predicting Fuel Ignition Properties from Low-Temperature Speciation Data

Using chemical kinetic modeling and statistical analysis, we investigate the possibility of correlating key chemical “markers”–typically small molecules–formed during very lean (φ ~ 0.001) oxidation experiments with near-stoichiometric (φ ~ 1) fuel ignition properties. One goal of this work is to evaluate the feasibility of designing a fuel-screening platform, based on small laboratory reactors that operate at low temperatures and use minimal fuel volume. Buras et al. [Combust. Flame2020,216, 472–484] have shown that convolutional neural net (CNN) fitting can be used to correlate first-stage ignition delay times (IDTs) with OH/HO2 measurements during very lean oxidation in low-T flow reactors with better than factor-of-2 accuracy. In this work, we test the limits of applying this correlation-based approach to predict the low-temperature heat release (LTHR) and total IDT, including the sensitivity of total IDT to the equivalence ratio, φ. We demonstrate that first-stage IDT can be reliably correlated with very lean oxidation measurements using compressed sensing (CS), which is simpler to implement than CNN fitting. LTHR can also be predicted via CS analysis, although the correlation quality is somewhat lower than for first-stage IDT. In contrast, the accuracy of total IDT prediction at φ = 1 is significantly lower (within a factor of 4 or worse). Furthermore, these results can be rationalized by the fact that the first-stage IDT and LTHR are primarily determined by low-temperature chemistry, whereas total IDT depends on low-, intermediate-, and high-temperature chemistry. Oxidation reactions are most important at low temperatures, and therefore, measurements of universal molecular markers of oxidation do not capture the full chemical complexity required to accurately predict the total IDT even at a single equivalence ratio. As a result, we find that φ-sensitivity of ignition delay cannot be predicted at all using solely correlation with lean low-T chemical speciation measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

An experimental and computational analysis of combustion heat release transformation in dual fuel combustion

Dual fuel (DF) diesel-methane combustion, which employs a high-reactivity fuel (diesel) to ignite a low-reactivity fuel (methane), is a widely studied combustion strategy for internal combustion engines, with significant potential for engine-out emissions reductions without the need for major hardware modifications. A phenomenon, which has been reported in the DF literature, but not explained fully, is the transformation of the shape of the apparent heat release rate (AHRR) curve as the start of injection (SOI) of diesel is advanced beyond a certain threshold; coincidentally, this AHRR transformation is usually accompanied by a sharp decrease in engine-out emissions of oxides of nitrogen (NOx). The goal of the present work is to establish the underlying physical reason(s) that cause the AHRR transformation. The AHRR transformation was observed on a single cylinder research engine (SCRE) at an indicated mean effective pressure (IMEP) of 5 bar at a speed of 1500 rev/min. The transformation occurred over a range of SOIs from 330 to 320 crank angle degrees (CAD). While the 330 CAD SOI exhibited a typical two-stage AHRR curve, with a clearly definable first-stage peak followed by a second-stage AHRR with little-to-no low temperature heat release (LTHR) present and high engine-out NOx, the 320 CAD SOI exhibited a single-stage, Gaussian-like AHRR curve, with noticeable LTHR and at least one order-of-magnitude lower NOx emissions. Here, leveraging analysis of experimental data and three-dimensional computational fluid dynamic simulations, the authors show that the AHRR transformation is impacted mainly by differences in local equivalence ratio distributions within the cylinder at ignition onset for different diesel SOIs.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

An Experimental and Numerical Investigation to Characterize the Low-Temperature Heat Release in Stoichiometric and Lean Combustion

This work reports on an experimental and modeling study on the low-temperature heat release (LTHR) characteristics for three RON 90 binary blends (n-heptane blended with isooctane, toluene and ethanol) in a Cooperative Fuel Research (CFR) engine at lean and stoichiometric conditions that are representative of homogeneous charge compression ignition (HCCI) and spark-ignition (SI) end-gas combustion conditions, respectively. An analysis of the end-gas temperature-pressure (T-P) trajectories was performed to identify the intake conditions leading to similar T-P trajectories between the two lambdas for each fuel blend. A heat release analysis was then conducted for the identified cases, where fuel-to-fuel differences in LTHR were identified and found to be sensitive to the operating condition. Simulations were conducted for these cases using a recently updated chemical kinetic model and a 0-D engine model, where good qualitative and reasonable quantitative agreements in LTHR were obtained. Sensitivity analysis was also performed directly on the rates of LTHR, to understand the controlling chemical reactions of LTHR, providing further insights into the fuel-to-fuel differences. The results demonstrate the significant promoting effect of n-heptane on LTHR rates, while inhibiting effects were seen for ethanol and toluene. Also highlighted was the importance of H atom abstraction reactions from the chemistry of each fuel component, which could lead to contradictory fuel behavior depending on the locations of the H site of the abstraction reaction due to the different ensuing pathways for the primary fuel radicals.

LTHR, RON 90 binary blends, sensitivity analysis↗
DOE OSTI2022

A Double-Wiebe Function for Reactivity Controlled Compression Ignition Combustion Using Reformate Diesel

Abstract Reactivity controlled compression ignition (RCCI) combustion has previously been proposed as a method to achieve high fuel conversion efficiency and reduce engine emissions. A single-fuel RCCI combustion strategy can have decreased fuel system complexity by using a reformate fuel for port fuel injection and the parent fuel (diesel) for direct injection. This paper presents a one-dimensional computational model of a compression ignition engine with single-fuel RCCI. A Wiebe function is used to predict the combustion process by representing the mass fraction burned (MFB) on a crank angle resolved basis. One single-Wiebe function (SWF) and two double-Wiebe functions(DWFs) were fitted to experimentally derive MFB data using the least-square method. The fitted results were compared with MFBs calculated from experimental data to verify the accuracy. The SWF did not fully capture the MFB curve with high fidelity while the detailed DWF captured the MFB curve within a root mean square error of 1.4%. The reduced double-Wiebe function (RDWF) also resulted in a predicted combustion profile with similar accuracy. Hence, the RDWF was used in a GT-power thermodynamic study to understand the effects of the low-temperature heat release (LTHR) fraction and combustion phasing on combustion characteristics. At optimum phasing of 5–10 crank angle degree after the top dead center, increasing the LTHR fraction from 20% to 60% resulted in the fuel conversion efficiency increasing from 39.5% to 41.1%, thus suggesting that the reformate fuel-based RCCI strategy is viable to unlock improved combustion performance.

Energy & Fuels↗
DOE OSTI2024

Independent Fuel Property Effects of Fuel Volatility on Low Temperature Heat Release and Fuel Autoignition (Final Report)

This Cooperative Research and Development Agreement (CRADA) project between Argonne National Laboratory (ANL), Oak Ridge National Laboratory (ORNL), and Shell Global Solutions (Shell) was initiated as part of a Directed Funding Opportunity (DFO) call for proposals from the Co-Optimization of Fuels and Engines (Co-Optima) initiative. Shell had observed that volatile fuels suppress low temperature heat release (LTHR) more than expected based on conventional gasoline autoignition metrics: research octane number (RON) and motor octane number (MON). The role of LTHR contributes to autoignition phenomena for both boosted spark ignition (BSI) and advanced compression ignition (ACI) combustion modes. ACI combustion modes are applicable to large engines in the hard-to-electrify applications such as off-road, rail, and marine. Thus, having a reliable understanding of autoignition phenomena, including being able to accurately account for the effects of fuel volatility, is particularly important as new synthetic and bio-fuel compositions are considered.This CRADA project aimed to test the hypothesis that the decreased LTHR is due to preferential evaporation of multicomponent fuels when using direct injection (DI) fueling technology, creating composition and reactivity stratification. A custom set of fuels was designed and blended to test this hypothesis by Shell, with experimental engine studies at ORNL and engine combustion modeling by ANL. However, the initial experimental findings did not show the expected effect of fuel volatility suppressing LTHR. Instead, the LTHR propensity observed was independent of the fuel volatility. Due to the unexpected experimental result, the remainder of the experimental effort was redirected to study the effect of fuel volatility on emissions under spark-ignited cold-start conditions. However, as with the LTHR experiments, the cold start effort did not show a meaningful effect of fuel volatility on cold start emissions. Meanwhile, improved engine CFD models have been developed for both LTHR and cold start operations for the Shell fuels with different volatilities. While the simulation efforts were not pursued further due to the insignificant effects of fuel volatility as shown in experiments, the models developed can be easily retooled for off-road, rail, and marine applications.

09 BIOMASS FUELS↗
DOE OSTI2021

Three-Dimensional CFD Investigation of Pre-Spark Heat Release in a Boosted SI Engine

Low-temperature heat release (LTHR) in spark-ignited internal combustion engines is a critical step toward the occurrence of auto-ignition, which can lead to an undesirable phenomenon known as engine knock. As such, correct predictions of LTHR are of utmost importance to improve the understanding of knock and enable techniques aimed at controlling it. While LTHR is typically obscured by the deflagration following the spark ignition, extremely late ignition timings can lead to LTHR occurrence prior to the spark, i.e., pre-spark heat release (PSHR). In this research, PSHR in a boosted direct-injection SI engine was numerically investigated using three-dimensional computational fluid dynamics (CFD). A hybrid approach was used, based on the G-equation model for representing the turbulent flame front and the multi-zone well-stirred reactor model for tracking the chemical reactions within the unburnt region. A recently developed best practice was also employed which keeps the well-stirred reactor model active throughout the entire simulation. This allowed for correct predictions of the previous cycle trapped residuals which have a considerable effect on the onset of LTHR. Multi-cycle simulations were conducted using Co-Optima alkylate and E30 fuels. The predicted in-cylinder pressure and heat release rate agreed well with the experimental data and served as validation for the CFD model. Following the initial validation, the dynamics of PSHR was discussed and a series of parameters of interest were assessed. First, the effect of exhaust valve temperature was investigated, qualitatively highlighting the importance of boundary conditions uncertainty. Further analyses were carried out on the effects of fuel properties, including laminar flame speed (LFS) and heat of vaporization (HOV). The results indicate that PSHR phasing is slightly advanced with lower LFS as more trapped unburnt fuel is made available for the next cycle. A similar trend was observed with lower HOV as less intense spray cooling led to higher mixture temperatures, i.e., higher mixture reactivity. Finally, a comparison of Co-Optima alkylate and E30 fuels was made using the pressure-temperature trajectory framework. It was shown that the differences between Co-Optima alkylate and E30 in PSHR tendency are correlated with both HOV and chemical effects.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Fuel Effects on Advanced Compression Ignition Load Limits

In order to increase the efficiency of light-duty gasoline engines, the Co-Optimization of Fuels and Engines (Co-Optima) initiative from the U.S. Department of Energy is investigating multi-mode combustion strategies. Multi-mode combustion can be describe as using conventional spark-ignited combustion at high loads, and at the part-load operating conditions, various advanced compression ignition (ACI) strategies are being investigated to increase efficiency. Of particular interest to the Co-Optima initiative is the extent to which optimal fuel properties and compositions can enable higher efficiency ACI combustion over larger portions of the operating map. Extending the speed-load range of these ACI modes can enable greater part-load efficiency improvements for multi-mode combustion strategies. In this manuscript, we investigate fuel effects for six different fuels, including four with a research octane number (RON) of 98 and differing fuel chemistries, iso-octane, and a market representative E10 fuel, on the load limits for two different ACI strategies: spark-assisted compression ignition (SACI) and partial fuel stratification-gasoline compression ignition (PFS-GCI) operation. Experimental results show that limits to intake boosting limit high load operation for most fuels, but high smoke emissions for high particulate matter index (PMI) fuels under SACI conditions could also be a limitation. Contrastingly, low load is limited by combustion efficiency, but these effects have more pronounced variation with fuel chemistry for PFS-GCI than with SACI. Additional, distinct effects affecting autoignition timing and peak heat release at higher speeds were identified for fuels having different low temperature heat release (LTHR) propensities for both ACI modes.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Experimental and Numerical Study on the Effect of Nitric Oxide on Autoignition and Knock in a Direct-Injection Spark-Ignition Engine

We report Nitric Oxide (NO) can significantly influence the autoignition reactivity and this can affect knock limits in conventional stoichiometric SI engines. Previous studies also revealed that the role of NO changes with fuel type. Fuels with high RON (Research Octane Number) and high Octane Sensitivity (S = RON – MON (Motor Octane Number)) exhibited monotonically retarding knocklimited combustion phasing (KL-CA50) with increasing NO. In contrast, for a high-RON, low-S fuel, the addition of NO initially resulted in a strongly retarded KL-CA50 but beyond the certain amount of NO, KL-CA50 advanced again. The current study focuses on same high-RON, low-S Alkylate fuel to better understand the mechanisms responsible for the reversal in the effect of NO on KLCA50 beyond a certain amount of NO. Experiments were conducted to measure the responses of KL-CA50 and trace-autoignition CA50, the latter being indicative of CA50 at which end-gas autoignition starts to become measurable from the apparent heat-release rate. Chemical-kinetics simulations were conducted to reveal the role of NO for end-gas autoignition, with a specific focus on sequential autoignition in a thermally stratified end-gas. The simulation results reveal that the magnitude of low-temperature heat release (LTHR) generally increases with NO. However, the relative importance of NO for enhancing LTHR diminishes when the LTHR inherent to a fuel’s chemistry is strong, such as at lower temperatures in a thermal boundary layer. This rendered more uniform LTHR within a hypothetical thermal boundary and led to a more sequential (i.e. slower) autoignition event. It was also revealed that a change in compression ratio influences the importance of intermediate-temperature heat release (ITHR) due to changes of the temperature-pressure history of the end-gas. Together with the condition where end-gas autoignition occurs more sequentially, the shorter time spent in LTHR and ITHR regime can counter the increase in autoignition reactivity at high NO levels and allow KLCA50 to advance

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Effect of NO on DME-Methanol HCCI Experimental Observations

Methanol is an attractive fuel for the maritime sector due to its wide availability. Its direct use as a fuel, however, is accompanied by challenges such as high latent heat of vaporization and low cetane number. A potential solution to overcome the ignition properties of methanol could be through on-board generation of dimethyl ether (DME) via catalytic dehydration of methanol. The resulting mixture from dehydration can be mixed in with the intake air to generate a homogenous charge compression ignition (HCCI) preburn for subsequent direct injection (DI) and successful ignition methanol at diesel–like timescales. However, if the preburn species are treated separately from the complete methanol MCCI approach the preburn heat release rate (HRR) phasing and behavior do not replicate the preburn behavior of the complete approach. Thus, the presence of the main methanol mixing controlled compression ignition (MCCI) combustion event influences the DME/methanol preburn kinetics. Specifically, it was found that trapped residual temperature alone was insufficient alone to be responsible for the observed differences, and that trace species concentrations of NO in the trapped residual gas also influenced DME/methanol kinetics increasing low temperature heat release (LTHR) magnitude and advancing high temperature heat release (HTHR) phasing. NO is not present in HCCI combustion of neat DME or DME/methanol blends nor is elevated gas temperature in the trapped residuals; both of which result in failure to accurately predict the HCCI combustion of DME/methanol blends when coupled with subsequent DI methanol MCCI. This work experimentally explores the effect of trapped residual temperature and NO on DME and DME/methanol HCCI combustion.

Jatana, Gurneesh [ORNL] (ORCID:0000000288903225)↗
DOE OSTI2020

Influence of pilot-fuel mixing on the spatio-temporal progression of two-stage autoignition of diesel-sprays in low-reactivity ambient fuel-air mixture

The spatial and temporal locations of autoignition for direct-injection compression-ignition engines depend on fuel chemistry, temperature, pressure, and mixing trajectories in the fuel jets. Dual-fuel systems can provide insight into both fuel-chemistry and physical effects by varying fuel reactivities and engine operating conditions. In this context, the spatial and temporal progression of two-stage autoignition of a diesel-fuel surrogate, n-heptane, in a lean-premixed charge of synthetic natural-gas (NG) and air is imaged in an optically accessible heavy-duty diesel engine. The lean-premixed charge of NG is prepared by fumigation upstream of the engine intake manifold. Optical diagnostics include high-speed (15kfps) cool-flame chemiluminescence-imaging as an indicator of low-temperature heat-release (LTHR) and OH* chemiluminescence-imaging as an indicator high-temperature heat-release (HTHR). NG prolongs the ignition delay of the pilot fuel and increases the combustion duration. Zero-dimensional chemical-kinetics simulations provide further understanding by replicating a Lagrangian perspective for mixtures evolving along streamlines originating either at the fuel nozzle or in the ambient gas, for which the pilot-fuel concentration is either decreasing or increasing, respectively. The zero-dimensional simulations predict that LTHR initiates most likely on the air streamlines before transitioning to HTHR, either on fuel-streamlines or on air-streamlines in regions of near-constant φ. Due to the relatively short pilot-fuel injection-durations, the transient increase in entrainment near the end of injection (entrainment wave) is important for quickly creating auto-ignitable mixtures. To achieve desired combustion characteristics, e.g., multiple ignition-kernels and favorable combustion phasing and location (e.g., for reducing wall heat-transfer or optimizing charge stratification), adjusting injection parameters could tailor mixing trajectories to offset changes in fuel ignition chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Octane Index Applicability over the Pressure-Temperature Domain

Modern boosted spark-ignition (SI) engines and emerging advanced compression ignition (ACI) engines operate under conditions that deviate substantially from the conditions of conventional autoignition metrics, namely the research and motor octane numbers (RON and MON). The octane index (OI) is an emerging autoignition metric based on RON and MON which was developed to better describe fuel knock resistance over a broader range of engine conditions. Prior research at Oak Ridge National Laboratory (ORNL) identified that OI performs reasonably well under stoichiometric boosted conditions, but inconsistencies exist in the ability of OI to predict autoignition behavior under ACI strategies. Instead, the autoignition behavior under ACI operation was found to correlate more closely to fuel composition, suggesting fuel chemistry differences that are insensitive to the conditions of the RON and MON tests may become the dominant factor under these high efficiency operating conditions. This investigation builds on earlier work to study autoignition behavior over six pressure-temperature (PT) trajectories that correspond to a wide range of operating conditions, including boosted SI operation, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). A total of 12 different fuels were investigated, including the Co-Optima core fuels and five fuels that represent refinery-relevant blending streams. It was found that, for the ACI operating modes investigated here, the low temperature reactions dominate reactivity, similar to boosted SI operating conditions because their PT trajectories lay close to the RON trajectory. Additionally, the OI metric was found to adequately predict autoignition resistance over the PT domain, for the ACI conditions investigated here, and for fuels from different chemical families. This finding is in contrast with the prior study using a different type of ACI operation with different thermodynamic conditions, specifically a significantly higher temperature at the start of compression, illustrating that fuel response depends highly on the ACI strategy being used.

02 PETROLEUM↗
DOE OSTI2026

Effect of NO on DME-Methanol HCCI Combustion Using a Reduced Chemical Kinetics Mechanism

Methanol is an attractive fuel for the maritime sector due to its wide availability. Its direct use as a fuel, however, is accompanied by challenges such as high latent heat of vaporization and low cetane number. A potential solution to overcome the ignition properties of methanol could be through on-board generation of dimethyl ether (DME) via catalytic dehydration of methanol. The resulting mixture from dehydration can be mixed in with the intake air to generate a homogenous charge compression ignition (HCCI) preburn for subsequent direct injection (DI) mixing controlled compression ignition (MCCI) of neat methanol. Within that context, complementary experimental work found that the influence of combustion residuals on the heat release rate (HRR) was significant, specifically for residual NO. This finding motivated the present computational and kinetic evaluation of the effects of NO on the low (LTHR) and high (HTHR) temperature heat release rates. The strong influence of small quantities of NO on the combustion process of a DME/methanol/H2O mixture (low catalyst or reactor efficiency) necessitated a kinetics-based investigation into this phenomenon. A mechanism sourced from the existing literature with NO had 172 species and 1375 reactions, making it computationally expensive for use. Hence, a mechanism reduction effort was implemented, and a rate constant (k) tuning effort based on sensitivity analysis was needed to validate experimental results using a zero-dimensional engine model in Cantera. The reduced mechanism was able to successfully capture the negligible influence of NO addition on DME HCCI combustion, whereas an advancement in LTHR and HTHR for a DME/methanol/H2O mixture was kinetically confirmed. Reaction pathway analysis showed that addition of NO chemically counteracted the OH sink created by alcohols like methanol, increasing the effectiveness of DME ignition.

Tyrewala, Daanish [ORNL] (ORCID:0000000208599324)↗