Search NASA⌕ Search

SEARCH · Search NASA

Results for “lubricant interaction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Investigation of Lubricant Additive Interactions on Gasoline Particulate Filters

To understand how the composition of novel lubricant additives and their ash interact with gasoline particulate filters (GPFs), an accelerated aging protocol was conducted using three lubricant additive formulations and two GPF types. The additive packages (adpaks) consisted of Ca+Mg detergent in a 3:1 or 0:1 ratio and an anti-wear component—either zinc dialkyl dithiophosphate (ZDDP) or a novel phosphonium-phosphinate ionic liquid (IL) substitute. The particulate sampling captured amount/compositions of particulate matter (PM) generated, total particulate number, and size distribution. Five ash loadings were completed. GPF position and adpak composition affected the backpressure, ash composition, ash morphology, and captured mass. The particulate sampling indicated that the ash component consisted primarily of particles less than 50 nm in size and that the Mg-only adpak resulted in more particulate of 50–400 nm in size. Postmortem materials characterization indicated GPFs in the underfloor position had deeper penetration of ash into the walls compared to the close-coupled position. Additionally, the Mg-only adpak had a higher filter collection efficiency (>90%) and the ash particles consisted of a higher concentration of dense ash material. In contrast, four of the 3:1 Ca:Mg lubricant adpaks resulted in a collection efficiency of only 40–50%. Although the collection efficiency was higher with the Mg-only adpak, the ash layer in the GPF was not thicker, nor was the penetration into the wall more significant, and surprisingly the full useful life (FUL) backpressure was lower than with Ca:Mg adpaks. The higher density of the Mg-derived ash was the only detectable difference. A possible explanation of this observation is that Mg ash has a lower melting point and is more susceptible to densification during combustion or GPF regeneration. The substitution of IL in place of the ZDDP did not lead to any notable changes in collection efficiency or location of the ash.

42 ENGINEERING↗
DOE OSTI2021

The quest for efficient oxygenated fuels: Examining interactions between lubricant components and oxygenates

This work empirically evaluated oxygenated blendstock-lubricant compatibility using a novel but simple method. The reactivity or compatibility was evaluated via gas chromatograph equipped with a flame ionization detector (GC-FID) before and after heating for 2h at 150 °C, which would roughly mimic conditions encountered in the combustion chamber of an Spark Ignition (SI) or Compression-Ignition (CI) engine. Five oxygenate blendstocks spanning several functional groups and chain lengths (prenol, isoprenol, butyl acetate, isohexanol, polyoxymethylene dimethyl ethers) were evaluated in a base fuel with nine variations of lubricant components of controlled concentrations, including fully formulated commercial lubricants. Baseline comparative examples were also generated, to decouple the effect of the oxygenate on the mixture, by heating only the base fuel with the lubricant component. Results demonstrate the relative compatibility between noted lubricants and oxygenates in base fuel upon heating. This was illustrated by minimal to no changes in the GC-FID traces. However, reactions of several of the chosen lubricants, especially Molybdenum di (2-ethylhexyl) phosphorodithioate (Molyvan L) and zinc dialkyldithiophosphate (ZDDP), with prenol and polyoxymethylene dimethyl ethers blendstocks showed substantial side reactions compared to corresponding baseline examples. Control experiments without oxygenates but comprising the same lubricant components showed no change in the mixture with heating. We concluded the incompatibility is due to the oxygenate and not the components of the base fuel. This preliminary work is valuable in establishing trends as well as provide useful information when a new component is introduced in the fuel.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Wear penalty for steel rubbing against hard coatings in reactive lubricants due to tribochemical interactions

Hard coatings and surface adsorptive/reactive lubricants are two common strategies for improving wear protection, but what if they are used together? In this study, steel-steel and steel-coating sliding was investigated in boundary lubrication of polar and non-polar oils containing a ZDDP or an ionic liquid. Two hard coatings, diamond-like-carbon (DLC) and chromium nitride (CrN), were used. Furthermore, for a steel-steel contact, wear was effectively reduced by using a more surface reactive lubricant, as expected. However, the steel ball wear was increased against a hard coating and further worsened with a more polar oil and/or a more surface reactive additive. The wear mechanism is proposed as a combined effect of physicochemical interactions with the lubricant, mechanical polishing by the counterface, and material adhesion.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shear Stress Dependence of Force Networks in 3D Dense Suspensions

The geometric organization and force networks of 3D dense suspensions that exhibit both shear thinning and thickening have been examined as a function of varying strength of interparticle attractive interactions using lubrication flow discrete element simulations. Significant rearrangement of the geometric topology does not occur at either the local or global scale as these systems transition across the shear thinning and shear thickening regimes. In contrast massive rearrangements in the balance of attractive, lubrication, and contact forces are observed with interesting behavior of network growth and competition. In agreement with prior work, in shear thinning regions the attractive force is dominant, however as the shear thickening region is approached there is growth of lubrication forces. Lubrication forces oppose the attraction forces, but as viscosity continues to increase under increasing shear stress, the lubrication forces are dominated by contact forces that also resist attraction. Contact forces are the dominant interactions during shear thickening and are an order of magnitude higher than their values in the shear-thinning regime. At high attractive interaction strength, contact networks can form even under shear thinning conditions, however high shear stress is still required before contact networks become the driving mechanism of shear thickening. Analysis of the contact force network during shear thickening generally indicate a uniformly spreading network that rapidly forms across empty domains, however the growth patterns have structure that are significantly dependent upon the strength of interparticle interactions, indicating subtle variations in the mechanism of shear thickening.

Edens, Lance E.↗
DOE OSTI2020

Ultralow Boundary Lubrication Friction by Three-Way Synergistic Interactions among Ionic Liquid, Friction Modifier, and Dispersant

Interactions among antiwear additives (AWs), friction modifiers (FMs), and dispersant in a lubricating oil are critical for tribological performance. This study investigates compatibilities of three oil-soluble ionic liquids (ILs, candidate AWs) with an FM, molybdenum dithiocarbamate (MoDTC), and a dispersant, polyisobutene succinimide (PIBSI) under boundary lubrication. Either synergistic or antagonistic effects were observed depending on the IL’s chemistry. Adding an aprotic phosphonium–alkylphosphate or phosphonium–alkylphosphinate IL into the oil containing MoDTC and PIBSI had detrimental impact on the friction and wear behavior. PIBSI was found to preferably interact/react with the aprotic IL to lose its ability of suspending MoDTC and to partially consume or even deplete the IL. In contrast, a protic ammonium–alkylphosphate IL seemed to be able to coexist with PIBSI and work synergistically with MoDTC, yielding a sustainable, ultralow boundary friction. A three-stage tribochemical process is proposed to explain how this IL + MoDTC pair interacts with the contact surface to form a chemically reacted, wear-protective tribofilm supporting a physically adsorbed, friction-reducing film on top. We report this study provides fundamental insights of the compatibilities among three common lubricant components, antiwear, friction modifier, and dispersant, which can be used to guide future lubricant development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Influence of Combustion Gas Temperatures on Piston Deposits for Diesel and Ammonia Dual-Fuel Combustion

As new fuels are adopted for marine engines, it is necessary to understand their impact on lubricant performance. In order to evaluate the performance of existing lubricants and inform the development of new ones, a deposit control test protocol has been developed using the ExxonMobil Enterprise two-stroke marine diesel research engine. Repeated tests at the target speed/load operating condition but different thermal conditions show that the temperature of the combustion gases is a key driver in the formation of deposits on piston surfaces, impacting both the quantity of deposits and whether they are hard or gummy. These impacts are examined for diesel combustion as well as ammonia dual-fuel combustion. Among alternative marine fuels, ammonia has perhaps the most unanswered questions regarding interactions with cylinder lubricants. The influence of ammonia dual-fuel combustion on the thermal conditions experienced by the lubricant are discussed. Scrape down oil samples were collected after operation with ammonia for analysis and comparison with fresh oil. Chemical analysis using a GC/MS instrument did not show significant permanent chemical changes in the lubricant due to ammonia exposure.

Kaul, Brian [ORNL] (ORCID:0000000184813620)↗
DOE OSTI2020

Dynamic clay microstructures emerge via ion complexation waves

Clays control carbon, water and nutrient transport in the lithosphere, promote cloud formation5 and lubricate fault slip through interactions among hydrated mineral interfaces. Clay mineral properties are difficult to model because their structures are disordered, curved and dynamic. Consequently, interactions at the clay mineral-aqueous interface have been approximated using electric double layer models based on single crystals of mica and atomistic simulations. We discover that waves of complexation dipoles at dynamically curving interfaces create an emergent long-range force that drives exfoliation and restacking over time- and length-scales that are not captured in existing models. Curvature delocalizes electrostatic interactions in ways that fundamentally differ from planar surfaces, altering the ratio of ions bound to the convex and concave sides of a layer. Multiple-scattering reconstruction of low-dose energy-filtered cryo electron tomography enabled direct imaging of ion complexes and electrolyte distributions at hydrated and curved mineral interfaces with {\aa}ngstrom resolution over micron length scales. Layers exfoliate and restack abruptly and repeatedly over timescales that depend strongly on the counterion identity, demonstrating that the strong coupling between elastic, electrostatic and hydration forces in clays promote collective reorganization previously thought to be a feature only of active matter.

Whittaker, Michael L↗
DOE OSTI2025

Methods to Observe Tribological Failures in Self-Mated Steel Contacts

Scuffing, a type of wear found in highly stressed or poorly lubricated contacts, is characterized by a rapid increase in friction and severe plastic deformation of the near-surface material. Scuffing has proven difficult to study because it initiates unpredictably, progresses rapidly, and typically develops within an inaccessible contact interface. Although there have been successful in-situ studies of scuffing in real-time, the transparent counter body needed for these studies changes the interactions between the surfaces and the lubricant, which affects the scuffing process in unknown ways. This paper describes the development of X-ray-compatible tribometry to study the scuffing of self-mated steels in-situ and in real-time. The method uses a crossed cylinders configuration with a thin (500 μm thick) stationary component and a small (≈200 μm) contact width to maximize X-ray interactions with atoms within the stress field generated by the contact. The resulting instrument and method are used to benchmark the scuffing response of self-mated 52,100 steel under tribologically challenging ‘oil-off’ lubrication conditions. The results demonstrate reliable scuffing in this configuration despite the relatively small contact areas and loads used. Following scuffing, gross plastic deformation was observed on both surfaces along with significant subsurface grain refinement and flow only on the stationary surface, which experienced constant contact. Interestingly, high friction initiated at specific locations of the migratory surface, which experienced intermittent contact, and then propagated across the track over time, suggesting that local conditions of the migratory surface dominated friction leading into the failure event.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fabrication and durability characterization of superhydrophobic and lubricant-infused surfaces

Hypothesis: Practical applications of non-wetting surfaces require good mechanical durability in the wet environments for which they are intended to be used. Durability of non-wetting surfaces is influenced by the surface features, interaction with the functionalization agent, and the lubricant properties that can be tuned independently to identify optimal combination. Experiments: In this study, superhydrophobic and lubricant-infused surfaces are fabricated on copper tubes using chemical etching and electrodeposition texturing techniques, six different functionalizing agents, and five different infused lubricants. Through 180 fabrication combinations and 102 durability tests, each parameter is systematically studied for contributions to initial non-wetting behavior and its durability in heated, wet environment, under high-energy water jet impingement, and under accelerated flow conditions. Findings: Among the adsorbing and curing functionalization agents investigated, n-Hexadecyl mercaptan that belongs to the sulfhydryl group and Sylgard-184, respectively, showed high durability in heated water immersion and under jet impingement tests. For lubricant-infused surfaces, lubricants with high surface tension demonstrated high durability in heated water immersion test, whereas durability in hydrodynamic conditions is closely correlated to lubricant viscosity. Results showed that a lubricant-infused surface will maintain its non-wetting properties in dropwise condensation conditions for approximately 1.5 years.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shear thinning rheology in a concentrated suspension of fibers: the role of attractive interactions

Fiber-reinforced composites are ubiquitously encountered in the engineering, automobile, and aerospace industries. Fabrication of these composites requires the mixing of fibers dispersed in a liquid, and the final structure is affected by fiber properties, interactions, and flow fields. A good understanding of the rheology of fiber suspensions can aid in the design and optimization of the fabrication processes. To this end, we simulate the simple shear flow of fiber suspensions by accounting for short range lubrication, van der Waals attractive, electrostatic repulsion interactions, as well as friction between fibers. Direct numerical simulations are performed using the Immersed Boundary Method where the fibers are modeled as flexible slender bodies governed by the Euler-Bernoulli beam theory and the fluid flow is resolved using the Navier-Stokes equations. The simulation results for the suspension viscosity and yield stress are consistent with the experimental data from the literature for polyamide fiber suspensions. The shear-thinning behavior becomes stronger as we increase the magnitude of attractive interactions. Furthermore, we perform a parametric study varying fiber flexibility, volume fraction, aspect ratio, inertia and examine suspension viscosity and yield stress.

Khan, Monsurul↗
DOE OSTI2026

Interfacial Adhesion Mechanism of Anionic Polyelectrolyte Brushes Induced by Oppositely Charged Macromolecular Counterions

Abstract Polyelectrolyte brushes are widely used as model systems for investigating electrostatic interactions at soft interfaces and to achieve exceptional lubrication properties. Previous studies have primarily focused on their behavior in the presence of multivalent counterions, which induce brush collapse, ionic crosslinking, and pronounced changes in interfacial structures. However, interactions between polyelectrolyte brushes and oppositely charged macromolecular counterions, such as polycations, remain poorly understood. Here, we prepare well-defined polystyrene sulfonate (PSS) brushes fabricated via surface-initiated grafting and employ surface forces apparatus measurements to investigate their interactions with oppositely charged polycations. In contrast to multivalent ions, polycations do not induce noticeable brush collapse, but instead generate significant adhesion between symmetric PSS brush layers. This adhesion increases with both contact time and applied load, eventually reaching a steady plateau, indicating that the interaction is governed not simply by electrostatic screening but by the gradual formation of polycation-mediated bridging under confinement. Furthermore, the introduction of monovalent Na+ ions disrupts the adhesive interaction even at very low concentrations, suggesting that the bridging function of the adsorbed polycation is highly sensitive to competitive ionic screening. In comparison, measurements with trivalent counterions reveal the expected brush collapse behavior but minimal dependence of adhesion on contact time, highlighting a clear mechanistic distinction from the polymeric counterion case. Collectively, these results demonstrate that molecular size, configurational restriction, and confinement-induced rearrangement, rather than charge valency alone, govern the interaction behavior of macromolecular counterions at brush interfaces. This work provides new insight into the molecular origins of adhesion and the regulation of interfacial interactions in charged polymer brush systems.

Park, Jinwoo [Argonne National Laboratory , , , ,;↗
DOE OSTI2020

Competitive Adsorption of Ionic Liquids Versus Friction Modifier and Anti-Wear Additive at Solid/Lubricant Interface—Speciation with Vibrational Sum Frequency Generation Spectroscopy

A modern lubricant contains various additives with different functionalities and the interactions or reactions between these additives could induce synergistic or antagonistic effects in tribological performance. In this study, sum frequency generation (SFG) spectroscopy was used to investigate competitive adsorption of lubricant additives at a solid/base oil interface. A silica substrate was used as a model solid surface. The lubricant additives studied here included two oil-soluble ionic liquids (ILs, [N888H][DEHP] and [P8888][DEHP]), an antiwear additive (secondary ZDDP), an organic friction modifier (OFM), and a dispersant (PIBSI). Our results showed that for mixtures of ZDDP and IL in a base oil (PAO4), the silica surface is dominated by the IL molecules. In the cases of base oils containing OFM and IL, the silica/lubricant interface is dominated by OFM over [N888H][DEHP], while it is preferentially occupied by [P8888][DEHP] over OFM. The presence of PIBSI in the mixture of PAO4 and IL leads to the formation of a mixed surface layer at the silica surface with PIBSI as a major component. The SFG results in this investigation provide fundamental insights that are helpful to design the formulation of new lubricant additives of desired properties.

25 ENERGY STORAGE↗
DOE OSTI2025

Bridging microscopic dynamics and rheology in the yielding of charged colloidal suspensions

The yielding of soft materials is critical to many natural and industrial processes, yet experimental insights into microscopic aspects of yielding are limited. This study combines angle X-ray scattering, X-ray photon correlation spectroscopy, and in situ rheology (Rheo-SAXS-XPCS) with fast lubrication dynamics simulations to examine how interparticle interactions influence yielding in charged colloidal suspensions. By tuning attraction through salt addition, we compare repulsive and attractive systems under deformation. Repulsive suspensions yield uniformly with Andrade-like creep and minimal structural change. In contrast, attractive suspensions show complex behaviors, including shear banding, delayed yielding, and resolidification, governed by transient dynamics at shear band interfaces. These results directly link microscopic particle dynamics to macroscopic flow and demonstrate how interaction potentials control rheological behavior. This work offers a framework for designing soft materials with tailored properties for applications in coatings, food processing, drug delivery, and other technologies requiring precise mechanical control.

Molecular Dynamics Simulation↗
DOE OSTI2025

Thermodynamic Water Activity Explains the Unusual Electrochemical Stability of Aqueous Deep Eutectic Solvents

The presence of water in nonaqueous deep eutectic solvent (DES) electrolytes has been debated in recent years, with efforts ranging from its complete removal to willful addition. It was shown that controlled amounts of water can be beneficial, as it not only enhances the physicochemical properties of these electrolytes but also has no significant detrimental effects on their electrochemical stability. Despite these advantages, there is still limited understanding of how water interacts with DES systems at the molecular level. This study examines the water activity in ethylene glycol and glycerol, as well as their binary mixtures with choline chloride to form the DESs ethaline and glyceline, respectively. In this work, we show that the high electrochemical stability of glyceline is related to its lower water activity compared to ethaline and can be attributed to the robust H-bonding network formed by the three hydroxyl groups of glycerol. Its 3D H-bond network effectively integrates water molecules within its solvent structure, reducing degradation and maintaining stability at higher water contents. The deviations from the ideal Raoult's law behavior are reflected in the water activity and activity coefficients, which highlight the intricate H-bond interactions within DES-water mixtures. Water acts like a lubricant within the more viscous DES mixtures without being detrimental to their electrochemical performance. The presented results emphasize the necessity of customizing DES-water compositions to enhance their performance as electrolytes, especially in flow battery applications where electrochemical stability, ionic conductivity, and fluidity are of utmost importance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Interactions of Water with Pristine and Defective MoS 2

Molybdenum disulfide (MoS 2 ) is a lamellar solid lubricant often used in aerospace applications because of its extremely low friction coefficient (~0.01) in inert environments. The lubrication performance of MoS 2 is significantly impaired by exposure to even small amounts of water and oxygen, and the mechanisms behind this remain poorly understood. Here we use density functional theory calculations to study the binding of water on MoS 2 sheets with and without defects. In general, we find that pristine MoS 2 is slightly hydrophilic but that defects greatly increase the binding affinity for water. Intercalated water disrupts the crystal structure of bulk MoS 2 due to the limited space between lamellae (~3.4 Å), and this leads to generally unfavorable adsorption, except in the cases where water molecules are located on the sites of sulfur vacancies. We also find that water adsorption is more favorable directly below a surface layer of MoS 2 compared to in the bulk.

36 MATERIALS SCIENCE↗