SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The present report contains three-component forces and mass-flow measurements on a jet nacelle at small inlet-velocity ratios v(sub A)/v(sub o) < 1. The mass-flow measurement on two cross sections of the nacelle demonstrate the local-velocity distribution with varying flow and angle of attack.
New quantitative turbulence measurements were obtained in a constant pressure, nonadiabatic hypersonic boundary layer, including the first higher moment and probability density measurements of mass-flow and total temperature fluctuations in hypersonic flow. The mass-flow and total temperature fluctuations show that the hypersonic data do not follow the trends set by lower Mach number adiabatic results. Measured intermittency distributions indicate substantial intermittency in the viscous sublayer and in the outer flow; significant differences between the present data and incompressible results are apparent. The higher moment and probability density data show that the character of the mass-flow and total temperature fluctuation modes are significantly different across the entire boundary layer. These differences together with turbulence scale and lifetime data obtained from autocorrelation and space-time correlation measurements are also discussed.-
This paper presents an experimental study of a turbulent boundary-layer/shock-wave interaction. The interaction was generated by a two-dimensional compression corner, and the flow was on the point of separating. Measurements were made using both normal and inclined hot wires, and the data include measurements of the longitudinal mass-flow fluctuation intensity and the mass-weighted Reynolds shear stress.
The performance of a constant-temperature normal hot-wire in a supersonic flow is critically examined. It is shown that this instrument is inherently unsuitable for measuring turbulent temperature correlations because of the highly nonlinear response to temperature fluctuations, particularly at low overheat ratios. The instrument is therefore limited to measurements of mean and fluctuating mass-flow rates. Suitable calibration procedures, as well as the limits on spatial and temporal resolution are discussed, and corrections for mean stagnation temperature changes are suggested.
Detailed hot-wire measurements of the longitudinal component of the mass-flow fluctuations have been made in an approximately self-preserving free shear layer reattaching on a 20 degree ramp at Mach number of 2.9. The experimental configuration is especially designed to provide a well-defined initial condition for the reattachment process. The absolute mass-flow turbulence intensity increases dramatically through the compression in the reattachment region, which is in sharp contrast to similar subsonic reattachments. It is clear that the mean dilatation contributes significantly to the turbulence amplification. In addition, the length scale is affected strongly by the presence of extra strain rates. Prediction of this flow will require some sophisticated modelling, and the challenge to the predictor is clear.
Measurements of the longitudinal component of the mass-flow fluctuations have been made in an 8-deg compression corner flow and a reattaching shear layer at a Mach number of approximately 2.9 and unit Reynolds number of about 7 x 10 to the 7th per m. The data include turbulence intensities and probability density distributions. Significant turbulence amplification occurs in both interactions. A qualitative explanation in terms of direct shock effects, extra strain rates, and their relative contribution, is suggested.
The nozzle test chamber was modified to provide a high-pressure-ratio nozzle static-test capability. Experiments were conducted to determine the range of the ratio of nozzle total pressure to chamber pressure and to make direct nozzle thrust measurements using a three-component strain-gage force balance. Pressure ratios from 3 to 285 were measured with several axisymmetric nozzles at a nozzle total pressure of 15 to 190 psia. Devices for measuring system mass flow were calibrated using standard axisymmetric convergent choked nozzles. System mass-flow rates up to 10 lbm/sec are measured. The measured thrust results of these nozzles are in good agreement with one-dimensional theoretical predictions for convergent nozzles.
Detailed interference force-and-pressure data were obtained on a representative supersonic transport wing-body-nacelle combination at Mach numbers of 0.9 to 1.4. The basic model consisted of a delta wing-body aerodynamic model with a length of 158.0 cm (62.2 in.) and a wingspan of 103.6 cm (40.8 in.) and four independently supported nacelles positioned beneath the model. The experimental program was conducted in the Ames 11- by 11-Foot Wind Tunnel at a constant unit Reynolds number. The primary variables examined included Mach number, angle of attack, nacelle position, and nacelle mass-flow ratio. Under the most favorable conditions, the net interference drag was equal to 50 percent the drag of four isolated nacelles at M = 1.4, 75 percent at M = 1.15, and 144 percent at M = 0.90. The overall interference effects were found to be rather constant over the operating angle-of-attack range of the configuration. The effects of mass-flow ratio on the interference pressure distributions were limited to the lip region of the nacelle and the local wing surface in the immediate vicinity of the nacelle lip. The net change in the measured interference forces resulting from variations in the nacelle mass-flow ratio were found to be quite small.
Sonic needle valves were calibrated to measure and control airflow in the suction system for the leading-edge flight test. The procedure and results for the calibration flow test of 4:41 flight valves are given. Mass-flow rates, which ranged from 0.001 to 0.012 lbm/sec, and maximum back pressure were measured for total temperatures from -30 F to 75 F and total pressures from 120 to 540 psf. Correlating equations are obtained for mass-flow rate as a function of total pressure, total temperature, and valve opening length. The most important aspect of flow measurement and control is found to be the measurement of valve opening length.
The measurements of part V (reference 1) of this series of reports, which concerned comparatively long ring profiles, are supplemented by measurements on shorter rings as they are used for shrouded propellers and cowlings of ring-shaped radiators. Mass-flow coefficients and profile drags are given. Furthermore, it has to be determined how far the potential theory describes the flow phenomenon with sufficient accuracy and whether the present theory for the calculation of thin annular profile yields useful profile forms and is suitable for determination of the mass flow for thick profiles.
An inlet-coldpipe assembly was placed in a Mach 0.4 stream to ingest the tip vortex of a forward mounted wing. The strongest vortex was produced by a wing angle of attack of 11 degrees. The vortex displayed a tangential velocity of 57 percent of local stream velocity prior to entering the inlet, and a tangential velocity of 25 percent of local velocity at the simulated compressor-face. The total-pressure profiles measured by standard compressor-face rakes were changed by the presence of the vortex only at the highest tested inlet mass-flow ratios.
Calculation of mass-flow and thrust produced for two-phase fluid mixture passing through choked nozzle
The system provides many of the gas mixtures required for calibrating analytical instruments used in engine exhaust gas analysis and is capable of blending from one to four additive gases with either of two carrier gases in concentrations from 20 ppm to 50%. Two mixtures can be flowing simultaneously. Performance tests were made to determine the stability accuracy of the system while it was in limited use for a period of 2 years. The accuracy of the blender was measured by comparing binary mixtures from the blender with National Bureau of Standards standard reference materials. Analytical instruments were used to make these comparisons. The expected accuracy of 2% was obtained in some of the tests, by the majority showed a systematic biAs of -5%. Although these tests revealed subtle instabilities in the flow controllers that contributed to the random scatter of data, the accuracy of wet test meters and bubble flowmeters used for calibration is marginal for this purpose. A simple procedure is recommended that should enable the full potential of the system to be realized.
Explore the source record for details and available documents.
Increasing the volume and length of the duct behind the inlet affected the inlet stability at Mach 2.0 and zero angle of attack. Close approximation of the inlet stability limit of the J34 engine-inlet configuration was obtained by a cold-pipe configuration having a length and volume approaching that measured to the engine turbine. Variation of these parameters had a small effect on the minimum subcritical stable mass flow below a cowl-lip-position parameter of 44 degrees and appeared to have a negligible effect on the inlet pressure-recovery - mass-flow curve. Initial buzz frequency and minimum cowl-lip-position parameter for complete buzz-free operation varied with configuration.
Wind-tunnel tests have been made to determine the static-pressure error resulting from external interference effects of flow through the static-pressure orifices of an NACA airspeed head at Mach numbers of 2.4, 3.0, and 4.0 for angles of attack of 0 deg, 5 deg, 10 deg, and 15 deg. Within the accuracy of the measurements and for the range of mass flow covered, the static-pressure error increased linearly with increasing mass-flow rate for both the forward and rear sets of orifices at all Mach numbers and angles of attack of the investigation. For a given value of flow coefficient, the static-pressure error varied appreciably with Mach number but only slightly with angle of attack. For example, for a flow coefficient out of the orifices of 0.01 (the approximate value for a vertically climbing airplane for which the airspeed system incorporates an airspeed meter, a Mach meter, and an altimeter), the error increased from about 5 percent to about 12 percent of the static pressure as the Mach number increased from 2.4 to 4.0 with the airspeed head at an angle of attack of 0 deg.
Experimental measurements of the attenuation of plane shock waves moving over rough walls have been made in a shock tube. Measurements of the boundary-layer characteristics, including thickness and velocity distribution behind the shock, have also been made with the aid of new cal techniques which provide direct information on the local boundary-layer conditions at the rough walls. Measurements of shock speed and shock pressure ratio are presented for both smooth-wall and rough-wall flow over lengths of machined-smooth and rough strips which lined all four walls of the shock tube. A simplified theory based on Von Karman's expression for skin-friction coefficient for flow over rough walls, along with a wave-model concept and extensions to include time effects, is presented. In this theory, the shock-tube flow is assumed to be one-dimensional at all times and the wave-model concept is used to relate the local layer growth to decreases in shock strength. This concept assumes that local boundary-layer growths act as local mass-flow sinks, which give rise to expansion waves which, in turn, overtake the shock and lower its mass flow accordingly.
A thermochemically-closed sonic-flow inversion framework (TSIF) is developed to infer bulk enthalpy and total temperature upstream of a choked nozzle in arc-jet flows. The formulation recasts a pressure-rise total enthalpy quantification technique as an inverse problem in characteristic-velocity c * space using measured mass flow rate, upstream total pressure, gas composition, and nozzle throat geometry as inputs. Unlike calorimetric energy-balance approaches or optical diagnostics, the method relies primarily on routinely measured facility quantities combined with explicit thermochemical closure. Thermochemical states are obtained using NASA’s open-source Chemical Equilibrium with Applications (CEA) code, enabling construction of a chemistry-consistent relation between characteristic velocity, total enthalpy, and total temperature under equilibrium or frozen assumptions. A discharge coefficient is self-calibrated using cold-flow (arc-off) operation data and applied to hot-flow (arc-on) measurements, enabling upstream losses to be accounted for without empirical correlations. The framework is applied to air, N 2 , and CO 2 –N 2 arc-jet flows and demonstrates expected trends for the inferred thermochemical states as function of arc power, specific energy input, mass-flow, heater configuration, and test gas. In the air limit, under equilibrium assumptions, the method recovers the classical high-enthalpy asymptotic correlation of Winovich with a mean residual of 4.4%, demonstrating compatibility with established sonic-flow scaling, while extending applicability to arbitrary multi-species mixtures and non-equilibrium chemistry. The framework provides a mixture-flexible methodology for determining bulk thermochemical states in modern arc-jet environments using routine facility pressure, mass-flow, gas-composition, and nozzle-geometry information together with a cold-flow calibration.