SEARCH · Search NASA

Results for “material traceability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS2020

Impact Testing of Inconel 718 for Material Impact Model Development

One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain-rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition, there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data, and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration (FAA) William J. Hughes Technical Center. Unique features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all of the raw data is available. Four parallel efforts are currently underway. The Ohio State University conducts both measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles. The George Mason University conducts the development of improved numerical modeling techniques for deformation and failure. Glenn conducts the impact testing of flat panels and substructures. This report describes impact testing performed on Inconel 718 sheet and plate samples of different thicknesses with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

J Michael Pereira↗

NASA NTRS2026

Impact Testing of 410 Stainless Steel for Material Impact Model Development

A project is underway to develop a consistent set of material properties, impact test data, and failure analysis for a variety of metallic aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration William J. Hughes Technical Center. Particular features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all the raw data are available. Four parallel efforts are currently underway: measurement of material deformation and failure response over a wide range of strain rates and temperatures, failure analysis of material property specimens and impact test articles, development of improved numerical modeling techniques for deformation and failure, and impact testing of flat panels and substructures for model validation. This report describes impact testing performed on 410 stainless steel sheet and plate samples of different thicknesses with two different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

410 Stainless Steel↗

NASA NTRSDate not supplied

Materials Informatics at NASA GRC: Machine Learning Surrogate Modeling, Data Management, and Integrated Toolsets for Establishing/Maintaining the Digital Thread

Integrated Computational Materials Engineering (ICME) has recently received widespread attention due to its promises in reducing dependence on physical testing for engineering design by relying on simulation, reducing both time and cost to market for various applications. ICME however requires validated multiscale material models, which heavily depend on available test data with full material and test pedigree, including material processing, test and measurement equipment, raw data collection, and analysis methodology and results that is findable and usable, along with integrated, efficient toolsets for effectively passing information across various length and time scales across such models. At the NASA Glenn Research Center under the Transformational Tools and Technologies Project, significant recent efforts have been directed towards establishing the required cyberinfrastructure to enable optimized ICME processes and the design of “fit-for-purpose” materials to achieve the goals outlined in the NASA Vision 2040 report. Such efforts include development of multiscale physics-based material models, which can be used to train highly efficient surrogate machine learning models, development of best practices and infrastructure for effective, traceable materials information management, and development of toolsets that integrate with physics-based codes, machine learning models, and an information management system to enable high throughput of materials data collection and analysis, establishment of digital twins and the digital thread, and automation of the ICME design process for material optimization.

Machine Learning↗

DOE OSTI2024

North America’s Potential for an Environmentally Sustainable Nickel, Manganese, and Cobalt Battery Value Chain

The Detroit Big Three General Motors (GMs), Ford, and Stellantis predict that electric vehicle (EV) sales will comprise 40–50% of the annual vehicle sales by 2030. Among the key components of LIBs, the LiNixMnyCo1−x−yO2 cathode, which comprises nickel, manganese, and cobalt (NMC) in various stoichiometric ratios, is widely used in EV batteries. This review reveals NMC cathodes from laboratory research. Furthermore, this study examines the environmental effect of NMC cathode production for EV batteries (including coating technologies), encompassing aspects such as energy consumption, water usage, and air emissions. Although gaps persist in NMC cathode environmental assessments (NMC111, NMC532, NMC622, and NMC811), limited life cycle assessments “(LCA)” have been conducted. Most available data originate from Asia (primarily China), accounting for 85% of the production of EV LIB cathode materials. The concept of battery passports for data collection on LIB components has been proposed to facilitate material traceability as a system for ensuring a sustainable supply chain for critical minerals. The automotive industry’s shift to electrification necessitates a sustainable supply chain from mine to vehicle end-of-life. As the critical mineral supply moves from Asia to North America, environmentally friendly industrial methods must be studied to provide this supply chain direction.

25 ENERGY STORAGE↗

DOE OSTI2023

Battery passports for promoting electric vehicle resale and repurposing

Starting in 2026, most batteries sold in the European Union will require a battery passport. This initiative is part of a broader legislative framework, led by the European Commission, to improve sustainable battery materials sourcing practices and enable a circular economy. All batteries having a capacity of greater than 2 kilowatt-hours will be covered under the legislation, effectively encompassing all electric vehicle (EV) batteries and stationary grid storage batteries. At its core, a battery passport defines a minimum, standard set of information that must be reported for every battery made and sold (see Figure 1). Legislative actions have so far focused on labeling standards enabling raw material traceability and recycling, which has received ongoing support from the European Council and Parliament. Furthermore, work remains to finalize the electrochemical performance and durability minimum reporting requirements by 2024, which has been challenging since performance and durability are subject to many different interpretations.

25 ENERGY STORAGE↗

NASA NTRS1978

Chemical releases

A Chemical Release Module to be carried into orbit by the shuttle is described. The module would release chemicals from orbiting satellites in order understand processes within the Earth's magnetosphere, atmosphere and ionosphere. A large number of potential experiments are identified, ranging from introducing traceable material into the solar wind in order to study its transport to and within the magnetosphere, to injecting material into the outer magnetosphere to simulate the precipitation of trapped charged particles, to the release of material at lower altitudes to create waves both mechanical and electromagnetic.

Heppner, J. P.↗

NASA NTRS2003

PEM-INST-001: Instructions for Plastic Encapsulated Microcircuit (PEM) Selection, Screening, and Qualification

Potential users of plastic encapsulated microcircuits (PEMs) need to be reminded that unlike the military system of producing robust high-reliability microcircuits that are designed to perform acceptably in a variety of harsh environments, PEMs are primarily designed for use in benign environments where equipment is easily accessed for repair or replacement. The methods of analysis applied to military products to demonstrate high reliability cannot always be applied to PEMs. This makes it difficult for users to characterize PEMs for two reasons: 1. Due to the major differences in design and construction, the standard test practices used to ensure that military devices are robust and have high reliability often cannot be applied to PEMs that have a smaller operating temperature range and are typically more frail and susceptible to moisture absorption. In contrast, high-reliability military microcircuits usually utilize large, robust, high-temperature packages that are hermetically sealed. 2. Unlike the military high-reliability system, users of PEMs have little visibility into commercial manufacturers proprietary design, materials, die traceability, and production processes and procedures. There is no central authority that monitors PEM commercial product for quality, and there are no controls in place that can be imposed across all commercial manufacturers to provide confidence to high-reliability users that a common acceptable level of quality exists for all PEMs manufacturers. Consequently, there is no guaranteed control over the type of reliability that is built into commercial product, and there is no guarantee that different lots from the same manufacturer are equally acceptable. And regarding application, there is no guarantee that commercial products intended for use in benign environments will provide acceptable performance and reliability in harsh space environments. The qualification and screening processes contained in this document are intended to detect poor-quality lots and screen out early random failures from use in space flight hardware. However, since it cannot be guaranteed that quality was designed and built into PEMs that are appropriate for space applications, users cannot screen in quality that may not exist. It must be understood that due to the variety of materials, processes, and technologies used to design and produce PEMs, this test process may not accelerate and detect all failure mechanisms. While the tests herein will increase user confidence that PEMs with otherwise unknown reliability can be used in space environments, such testing may not guarantee the same level of reliability offered by military microcircuits. PEMs should only be used where due to performance needs there are no alternatives in the military high-reliability market, and projects are willing to accept higher risk.

Teverovsky, Alexander↗

NASA NTRS1982

Advanced manufacturing development of a composite empennage component for L-1011 aircraft

This is the final report of technical work conducted during the fourth phase of a multiphase program having the objective of the design, development and flight evaluation of an advanced composite empennage component manufactured in a production environment at a cost competitive with those of its metal counterpart, and at a weight savings of at least 20 percent. The empennage component selected for this program is the vertical fin box of the L-1011 aircraft. The box structure extends from the fuselage production joint to the tip rib and includes front and rear spars. During Phase 4 of the program, production quality tooling was designed and manufactured to produce three sets of covers, ribs, spars, miscellaneous parts, and subassemblies to assemble three complete ACVF units. Recurring and nonrecurring cost data were compiled and documented in the updated producibility/design to cost plan. Nondestruct inspections, quality control tests, and quality acceptance tests were performed in accordance with the quality assurance plan and the structural integrity control plan. Records were maintained to provide traceability of material and parts throughout the manufacturing development phase. It was also determined that additional tooling would not be required to support the current and projected L-1011 production rate.

Alva, T.↗

NASA NTRS2003

Current Developments in Future Planetary Probe Sensors for TPS

In-situ Thermal Protection System (TPS) sensors are required to provide traceability of TPS performance and sizing tools. Traceability will lead to higher fidelity design tools, which in turn will lead to lower design safety margins, and decreased heatshield mass. Decreasing TPS mass will enable certain missions that are not otherwise feasible, and directly increase science payload. NASA Ames is currently developing two flight measurements as essential to advancing the state of TPS traceability for material modeling and aerothermal simulation: heat flux and surface recession (for ablators). The heat flux gage is applicable to both ablators and non-ablators and is therefore the more generalized sensor concept of the two with wider applicability to mission scenarios. This paper describes the development of a microsensor capable of surface and in-depth temperature and heat flux measurements for TPS materials appropriate to Titan, Neptune, and Mars aerocapture, and direct entry. The thermal sensor will be monolithic solid state devices composed of thick film platinum RTD on an alumina substrate. Choice of materials and critical dimensions are used to tailor gage response, determined during calibration activities, to specific (forebody vs. aftbody) heating environments. Current design has maximum operating temperature of 1500 K, and allowable constant heat flux of q=28.7 watts per square centimeter, and time constants between 0.05 and 0.2 seconds. The catalytic and radiative response of these heat flux gages can also be changed through the use of appropriate coatings. By using several co-located gages with various surface coatings, data can be obtained to isolate surface heat flux components due to radiation, catalycity and convection. Selectivity to radiative heat flux is a useful feature even for an in-depth gage, as radiative transport may be a significant heat transport mechanism for porous TPS materials in Titan aerocapture. This paper also reports on progress to adapt a previously flown surface recession sensor, based on the Jupiter probe Galileo Analog Resistance Ablation Detector (ARAD), to appropriate aerocapture conditions.

Martinez, Ed↗

NASA NTRS2005

Development of Solid State Thermal Sensors for Aeroshell TPS Flight Applications

In-situ Thermal Protection System (TPS) sensors are required to provide verification by traceability of TPS performance and sizing tools. Traceability will lead to higher fidelity design tools, which in turn will lead to lower design safety margins, and decreased heatshield mass. Decreasing TPS mass will enable certain missions that are not otherwise feasible, and directly increase science payload. NASA Ames is currently developing two flight measurements as essential to advancing the state of TPS traceability for material modeling and aerothermal simulation: heat flux and surface recession (for ablators). The heat flux gage is applicable to both ablators and non-ablators and is therefore the more generalized sensor concept of the two with wider applicability to mission scenarios. This paper describes the continuing development of a thermal microsensor capable of surface and in-depth temperature and heat flux measurements for TPS materials appropriate to Titan, Neptune, and Mars aerocapture, and direct entry. The thermal sensor is a monolithic solid state device composed of thick film platinum RTD on an alumina substrate. Choice of materials and critical dimensions are used to tailor gage response, determined during calibration activities, to specific (forebody vs. aftbody) heating environments. Current design has maximum operating temperature of 1500K, and allowable constant heat flux of q=28.7 W/cm(sup 2), and time constants between 0.05 and 0.2 seconds. The catalytic and radiative response of these heat flux gages can also be changed through the use of appropriate coatings. By using several co-located gages with various surface coatings, data can be obtained to isolate surface heat flux components due to radiation, catalycity and convection. Selectivity to radiative heat flux is a useful feature even for an in-depth gage, as radiative transport may be a significant heat transport mechanism for porous TPS materials in Titan aerocapture.

Martinez, Ed↗

NASA NTRS2006

Development of Standardized Lunar Regolith Simulant Materials

Carpenter, P.↗

NASA NTRS2006

Development of Standardized Lunar Regolith Simulant Materials

Lunar exploration requires scientific and engineering studies using standardized testing procedures that ultimately support flight certification of technologies and hardware. It is necessary to anticipate the range of source materials and environmental constraints that are expected on the Moon and Mars, and to evaluate in-situ resource utilization (ISRU) coupled with testing and development. We describe here the development of standardized lunar regolith simulant (SLRS) materials that are traceable inter-laboratory standards for testing and technology development. These SLRS materials must simulate the lunar regolith in terms of physical, chemical, and mineralogical properties. A summary of these issues is contained in the 2005 Workshop on Lunar Regolith Simulant Materials [l]. Lunar mare basalt simulants MLS-1 and JSC-1 were developed in the late 1980s. MLS-1 approximates an Apollo 11 high-Ti basalt, and was produced by milling of a holocrystalline, coarse-grained intrusive gabbro (Fig. 1). JSC-1 approximates an Apollo 14 basalt with a relatively low-Ti content, and was obtained from a glassy volcanic ash (Fig. 2). Supplies of MLS-1 and JSC-1 have been exhausted and these materials are no longer available. No highland anorthosite simulant was previously developed. Upcoming lunar polar missions thus require the identification, assessment, and development of both mare and highland simulants. A lunar regolith simulant is manufactured from terrestrial components for the purpose of simulating the physical and chemical properties of the lunar regolith. Significant challenges exist in the identification of appropriate terrestrial source materials. Lunar materials formed under comparatively reducing conditions in the absence of water, and were modified by meteorite impact events. Terrestrial materials formed under more oxidizing conditions with significantly greater access to water, and were modified by a wide range of weathering processes. The composition space of lunar materials can be modeled by mixing programs utilizing a low-Ti basalt, ilmenite, KREEP component, high-Ca anorthosite, and meteoritic components. This approach has been used for genetic studies of lunar samples via chemical and modal analysis. A reduced composition space may be appropriate for simulant development, but it is necessary to determine the controlling properties that affect the physical, chemical and mineralogical components of the simulant.

Carpenter, P.↗

NASA NTRS2024

Automation of the ICME Workflow Incorporating Material Digital Twins at Different Length Scales Within a Robust Information Management System

Recent successes in Integrated Computational Materials Engineering (ICME) have demonstrated the potential in designing ‘fit-for-purpose’ materials for a given application in a cost and time efficient manner. However, the material design process must contain a level of judicious automation in the material decision process; that is implementing some optimization algorithms to truly enable the benefits of ICME, particularly when considering materials at multiple length and time scales. Furthermore, the ability to effectively store developed material models, experimental data used for validation, and link models at multiple length and time scales must be implemented to ensure traceability across the material design process, such that the data gathered can be leveraged towards efficient material design. To enable such an optimization scheme a robust framework must exist: (1) that can capture changes made at a given length scale, (2) automatically propagate changes upstream to the highest scale, and (3) evaluate the material’s performance at the structural level. In this work, a developed framework for tracking material changes, automatically running the necessary simulations to determine the properties at the next highest scale, and saving each iteration of the design process to maintain the application’s digital thread is presented for polymer matrix composites (PMCs). The Automated Information Management Across Organizations and Scales (AIMAOS) program offers users an interactive graphical user interface (GUI) for defining constituent materials, building lamina and laminates, and applying effective laminate properties to finite element and composite optimization third party software. At each length scale, the necessary input files are automatically written, and subsequent analysis tools are called to solve for effective properties at the next scale, which are then read by the AIMAOS tool and displayed to the user. As changes are made to the material at lower length scales, information is automatically propagated upstream to higher length scales, and changes made are automatically tracked and versioned to maintain traceability during the design process. The AIMAOS tools serves as the first step in enabling optimized design of composites from the nano to the macroscale for a given application.

Brandon L Hearley↗

NASA NTRS2005

DEVELOPMENT OF STANDARDIZED LUNAR REGOLITH SIMULANT MATERIALS

Lunar exploration activities require scientific and engineering studies that use standardized testing procedures and ultimately support flight certification of hardware and the development of technologies for their use on the lunar surface. It is necessary to anticipate the full range of source materials and environmental constraints that are expected on the Moon and Mars, and to evaluate in-situ resource utilization (ISRU) coupled with testing and development. Historical use of lunar simulants has focused on physical aspects of the lunar regolith for landing and transportation activities. Lunar mare simulants MLS-1 and JSC-1 have been developed, but supplies have been exhausted. Renewed emphasis on exploration and ISRU activities requires development of standardized simulant reference materials that are traceable interlaboratory standards for testing and simulate the lunar regolith in terms of physical, chemical, and mineralogical properties. This new generation of lunar regolith simulants must therefore support both technological development and testing methods. These issues were extensively discussed at the 2005 Lunar Regolith Simulant Materials Workshop.

Carpenter, P.↗

DOE OSTI2022

Technical Guidance for Creation of 237 NP Irradiation Target Fabrication Packages

This document describes the process used to document the fabrication of irradiation targets that may be inserted into either the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL), or the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). The targets are being irradiated to produce 238 Pu (5.48Mev alpha decay, T1/2 = 87.7 y) used in the fabrication of radioisotope thermoelectric generators (RTGs). RTGs powered by 238 Pu are an established power source technology for National Aeronautics and Space Administration space missions where solar power is not viable. The documentation included in fabrication files demonstrates full traceability of all materials, components, and assemblies used to build 237 Np targets. To accomplish this, all documentation (e.g., certified material test reports, weld reports, leak test reports) will be maintained and reviewed throughout materials procurement, component fabrication, and target assembly.

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2020

A highly-enriched 244 Pu reference material for nuclear safeguards and nuclear forensics measurements

A highly-enriched 244 Pu isotope dilution reference material has been prepared and characterized for metrologically traceable measurements of very small quantities of plutonium. The amount of plutonium in samples associated with nuclear safeguards and nuclear forensic measurements can be significantly less than 1 ng. Accordingly, the ability to quantify the amount and isotopic composition of plutonium from a single mass-spectrometric analysis is particularly desirable. The highly-enriched 244 Pu reference material, described here, will minimize the magnitude of spike corrections necessary to obtain accurate information on plutonium isotopic composition from isotope dilution measurements.

07 ISOTOPE AND RADIATION SOURCES↗

NASA NTRS2023

NASA GRC ICME Schema for Materials Data Management: An Executive Summary

Integrated Computational Materials Engineering (ICME) has received a growing emphasis in attention due its potential impact on rapid material design, reduction in cost and time to market for new applications, and the promise of ‘fit-for-purpose’ materials coupled with recent advances in high performance computing and material characterization tools. However, for an organization to implement ICME practices for material discovery and design, a series of both technical and cultural challenges must be overcome to foster an environment that enables efficient, traceable, and predictive multiscale simulations of material behavior to enable virtual design of materials. In 2016, NASA sponsored a 2040 Vision study to define the potential 25-year future state required for integrated multiscale modeling of materials and systems to improve both the associated time and cost for aerospace and aeronautical innovation. The study envisions a cyber-physical-social ecosystem of experimentally validated computational models, tools, and techniques, along with the associated digital tapestry, that can enable rapid, optimized, ‘fit-for-purpose’ design of materials, components, and systems. A key requirement for such an ecosystem is the development of a robust information management system for materials across their full lifecycle, including material pedigree, experimental (real) and virtual (simulation) data, developed material models, and the implementation of models in engineering applications, such that process-structure-property-performance relationships can be established, thereby enabling the virtual design and optimization of materials. Such an information management system must be able to effectively capture: i) material information at each length scale; ii) test data and analysis; iii) associated material models; and iv) material and model deployment in engineering applications. These systems must also provide traceability between experimental and virtual representations of the material to ensure, when appropriate, the material digital twin is maintained. Additionally, this robust material information management system must be able to seamlessly connect with both commercial and an organization’s in-house software tools, be they analysis tools, other material databases, product lifecycle management (PLM) or simulation data management (SDM) tools, etc., such that automation of the design and analysis of a material across multiple length scales is possible. In this paper, an executive summary of the NASA GRC ICME Schema for materials information management is presented. The database best practices and schema design philosophy specifically for ICME materials data management and an overview description of each element in the schema is given, along with its associated role in an ICME workflow. Additionally, auxiliary tools that interact with the database and provide judicious automation with regards to importing, exporting, and analyzing materials data are presented. Such tools are critical to an ICME ecosystem, not only for their role in enabling optimization, but also in relieving users of tedious manual tasks, thus helping to promote adoption and combat the cultural challenges organizations face in enabling ICME.

Materials↗

NASA NTRS2016

Information Management Workflow and Tools Enabling Multiscale Modeling Within ICME Paradigm

With the increased emphasis on reducing the cost and time to market of new materials, the need for analytical tools that enable the virtual design and optimization of materials throughout their processing - internal structure - property - performance envelope, along with the capturing and storing of the associated material and model information across its lifecycle, has become critical. This need is also fueled by the demands for higher efficiency in material testing; consistency, quality and traceability of data; product design; engineering analysis; as well as control of access to proprietary or sensitive information. Fortunately, material information management systems and physics-based multiscale modeling methods have kept pace with the growing user demands. Herein, recent efforts to establish workflow for and demonstrate a unique set of web application tools for linking NASA GRC's Integrated Computational Materials Engineering (ICME) Granta MI database schema and NASA GRC's Integrated multiscale Micromechanics Analysis Code (ImMAC) software toolset are presented. The goal is to enable seamless coupling between both test data and simulation data, which is captured and tracked automatically within Granta MI®, with full model pedigree information. These tools, and this type of linkage, are foundational to realizing the full potential of ICME, in which materials processing, microstructure, properties, and performance are coupled to enable application-driven design and optimization of materials and structures.

Materials Engineering↗