Search NASA⌕ Search

SEARCH · Search NASA

Results for “metallurgy & metallurgical engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

SA508 low alloy steel to 316L stainless steel dissimilar metal joint made by powder metallurgy hot isostatic pressing

Joining ferritic SA508 low alloy steel (LAS) and austenitic 316 L stainless steel (SS) via powder metallurgy hot isostatic pressing (PM-HIP) was evaluated as an alternative method to welding. This study investigated the mechanical and microstructural evolutions of the bimetallic interface under different joint designs and heat treatments. Here, the direct joining of dissimilar metal alloys by PM-HIP method resulted in two designs: 1) powder SA508 to solid bar 316 L (P508–B316L) and 2) powder 316 L solid bar SA508 (P316L-B508). In both cases, P508–B316L and P316L-demonstrated satisfactory tensile strength, however, high hardness and severe depreciation in toughness were located on the bimetallic interface. The mechanisms responsible for the detrimental mechanical properties were verified. Large oxides were observed in P508–B316L due to the prior powder boundary (PPB) oxides present in SA508 powder. The intense sensitization occurred from the formation of M 23 C 6 carbides, consequently from the slow cooling after PM-HIP in P316L-B508. Post-HIP heat treatments were explored to reduce the distance of carbide formation; however, the heat treatment could not eliminate the carbides. The experimental results were compared to the diffusion couple simulation as a function of carbide formation with distance. The analysis also showed the high hardness at the bimetallic interface was primarily contributed by solid solution strengthening. In conclusion, the direct joining of P316L-B508 and P508–B316L via PM-HIP was deemed to be unfeasible, and a transitional material is necessary to impede the diffusion of carbon.

316L stainless Steel↗
DOE OSTI2020

The effect of Ni doping on the mechanical behavior of tungsten

The effect of nickel (Ni) on activated sintering of tungsten has been known and investigated for decades. However, there are few reports on the mechanical properties of tungsten when Ni is added as a low alloying additive with less than 1 wt%. In this work, the mechanical behaviors of tungsten doped with 0.2–1.0 wt% nickel from room temperature up to 400 °C were investigated. The results show that the compression ductility of as-sintered Ni doped tungsten is drastically higher than that of as-sintered pure tungsten at all tested temperatures including room temperature, and the fracture toughness at room temperature is increased by 92%. The results suggest that the ductile-to-brittle transition temperature (DBTT) of tungsten can be reduced substantially by doping with Ni.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The Effect of Antiphase Boundary Tubes on the Hardness of FeAl

The high work hardening rate unique to ordered intermetallic alloys has long been attributed to antiphase boundary (APB) tubes. In this work, APB tubes are introduced in Fe–40 at. pct Al and Fe–43 at. pct Al by cold-rolling and then removed by annealing. The presence and absence of APB tubes is verified with magnetic measurements. When APB tubes are annealed out the hardness does not change, thus indicating that APB tubes do not contribute to strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of precipitation in gradient Inconel 718 superalloy

Inconel 718 (IN718) superalloy is a well-established material for the application of aircraft engine and power generator due to its excellent performance at high temperatures. The outstanding mechanical properties of IN718 are largely determined by the precipitates. Here, we investigated the precipitation behaviors and the corresponding mechanical properties of the heat-treated gradient IN718 alloy. The microscopy studies reveal that high-density hexagonal η phase with chemistry of Ni 3 (Al,Ti,Nb) formed in the nanograined IN718 alloy after annealing at 700 °C. Additionally, the compressive stress introduced during severe plastic deformation may have prohibited the formation of γ” phase while accelerated the precipitation of γ’ phase, consequently favoring the precipitation of η phase. The corresponding evolution of mechanical behavior of gradient IN718 alloy is investigated.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Computational thermodynamics and its applications

Thermodynamics is a science concerning the state of a system, whether it is stable, metastable or un- stable, when interacting with the surroundings. In this overview, fundamentals of thermodynamics are briefly reviewed through the combination of first and second laws of thermodynamics for open and nonequilibrium systems to demonstrate that the reversible equilibrium and irreversible nonequilibrium thermodynamics can be integrated to enhance the power and utilities of thermodynamics. The recent progresses in computational thermodynamics, the remaining challenges, and potential impacts in broad scientific fields are discussed here. It is shown that computational thermodynamics enables the modeling of thermodynamics of a state as a function of both external and internal variables and quantitative calculations of a broad range of properties of a multicomponent system in terms of first and second derivatives of energy, including not only equilibrium states when there are no driving forces for any internal processes and but also non-equilibrium states with driving forces for internal processes. Consequently, external constraints such as fixed strain and internal degree of freedoms such as ordering and defects can be described in a coherent framework and applied to materials design. Furthermore, two important but largely overlooked aspects in thermodynamics will be discussed, i.e. the rigorous application of statistical thermodynamics with the probability of configurations and their contributions to system properties, and the applications of second derivatives of energy with respect to either two extensive variables or two potentials or a mixture of them in terms of understanding and predicting emergent behaviors, critical phenomena, kinetic coefficients, and mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Thermodynamics and its prediction and CALPHAD modeling: Review, state of the art, and perspectives

Thermodynamics is a science concerning the state of a system, whether it is stable, metastable, or unstable, when interacting with its surroundings. The combined law of thermodynamics derived by Gibbs about 150 years ago laid the foundation of thermodynamics. In Gibbs combined law, the entropy production due to internal processes was not included, and the 2nd law was thus practically removed from the Gibbs combined law, so it is only applicable to systems under equilibrium, thus commonly termed as equilibrium or Gibbs thermodynamics. Gibbs further derived the classical statistical thermodynamics in terms of the probability of configurations in a system in the later 1800's and early 1900's. With the quantum mechanics (QM) developed in 1920's, the QM-based statistical thermodynamics was established and connected to classical statistical thermodynamics at the classical limit as shown by Landau in the 1940's. In 1960's the development of density functional theory (DFT) by Kohn and co-workers enabled the QM prediction of properties of the ground state of a system. On the other hand, the entropy production due to internal processes in non-equilibrium systems was studied separately by Onsager in 1930's and Prigogine and co-workers in the 1950's. In 1960's to 1970's the digitization of thermodynamics was developed by Kaufman in the framework of the CALculation of PHAse Diagrams (CALPHAD) modeling of individual phases with internal degrees of freedom. CALPHAD modeling of thermodynamics and atomic transport properties has enabled computational design of complex materials in the last 50 years. Our recently termed zentropy theory integrates DFT and statistical mechanics through the replacement of the internal energy of each individual configuration by its DFT-predicted free energy. The zentropy theory is capable of accurately predicting the free energy of individual phases, transition temperatures and properties of magnetic and ferroelectric materials with free energies of individual configurations solely from DFT-based calculations and without fitting parameters, and is being tested for other phenomena including superconductivity, quantum criticality, and black holes. Those predictions include the singularity at critical points with divergence of physical properties, negative thermal expansion, and the strongly correlated physics. Furthermore, those individual configurations may thus be considered as the genomic building blocks of individual phases in the spirit of the materials genome®. This has the potential to shift the paradigm of CALPHAD modeling from being heavily dependent on experimental inputs to becoming fully predictive with inputs solely from DFT-based calculations and machine learning models built on those calculations and existing experimental data through newly developed and future open-source tools. Furthermore, through the combined law of thermodynamics including the internal entropy production, it is shown that the kinetic coefficient matrix of independent internal processes is diagonal with respect to the conjugate potentials in the combined law, and the cross phenomena that the phenomenological Onsager flux and reciprocal relationships are due to the dependence of the conjugate potential of a molar quantity on nonconjugate molar quantities and other potentials, which can be predicted by the zentropy theory and CALPHAD modeling.

42 ENGINEERING↗
DOE OSTI2020

Effect of water vapor on high-temperature oxidation of NiAl alloy

The high-temperature oxidation of NiAl is studied with dry oxygen and water vapor. The oxidation in H 2 O results in a thicker Al 2 O 3 oxide scale than that in O 2 . The oxide scale formed initially is a single layer of γ-Al 2 O 3 that subsequently transforms into a α-Al 2 O 3 /γ-Al 2 O 3 bilayer structure, in which the inner α-Al2O3 layer formed in H2O has a higher porosity than that in O 2 . Finally, further density functional theory calculations show that H protons derived from H 2 O molecules penetrate into the oxide lattice and boost the formation of lattice vacancies in both α-Al 2 O 3 and γ-Al 2 O 3 , thus enhancing the oxide scale growth.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Differences in Sb 2 Te 3 growth by pulsed laser and sputter deposition

High quality van der Waals chalcogenides are important for phase change data storage, thermoelectrics, and spintronics. Using a combination of statistical design of experiments and density functional theory, we clarify how out-of-equilibrium van der Waals epitaxial deposition methods can improve the crystal quality of Sb 2 Te 3 films. We compare films grown by radio frequency sputtering and pulsed laser deposition (PLD). The growth factors that influence the crystal quality for each method are different. For PLD grown films a thin amorphous Sb 2 Te 3 seed layer most significantly influences the crystal quality. In contrast, the crystalline quality of films grown by sputtering is rather sensitive to the deposition temperature and less affected by the presence of a seed layer. This difference is somewhat surprising as both methods are out-of-thermal-equilibrium plasma-based methods. Non-adiabatic quantum molecular dynamics simulations show that this difference originates from the density of excited atoms in the plasma. The PLD plasma is more intense and with higher energy than that used in sputtering, and this increases the electronic temperature of the deposited atoms, which concomitantly increases the adatom diffusion lengths in PLD. In contrast, the adatom diffusivity is dominated by the thermal temperature for sputter grown films. These results explain the wide range of Sb 2 Te 3 and superlattice crystal qualities observed in the literature. Finally, these results indicate that, contrary to popular belief, plasma-based deposition methods are suitable for growing high quality crystalline chalcogenides.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Degradation of solid oxide electrolysis cells: Phenomena, mechanisms, and emerging mitigation strategies—A review

Solid oxide electrolysis cell (SOEC) is a promising electrochemical device with high efficiency for energy storage and conversion. However, the degradation of SOEC is a significant barrier to commercial viability. In this review article, the typical degradation phenomena of SOEC are summarized, with great attention into the anodes/oxygen electrodes, including the commonly used and newly developed anode materials. Meanwhile, mechanistic investigations on the electrode/electrolyte interfaces are provided to unveil how the intrinsic factor, oxygen partial pressure , and the electrochemical operation conditions, affect the interfacial stability of SOEC. At last, this paper also presents some emerging mitigation strategies to circumvent long-term degradation, which include novel infiltration method, development of new anode materials and engineering of the microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Automated identification of deformation twin systems in Mg WE43 from SEM DIC

In this study, the application of machine learning and computer vision approaches to microscale deformation data for the automated identification of deformation twinning systems, and their associated twin area, is introduced. Deformation data was obtained during in-situ SEM compression testing of a WE43 Mg alloy using digital image correlation (DIC) modified for use with electron microscopy. A 5.7 mm × 3.4 mm area of interest was analyzed, generating ~100 million data points of deformation. Experimental twin trace directions were determined by applying k-means clustering, morphological thinning, and Hough transforms to the deformation data. The identification of deformation twinning was achieved by consideration of the twin trace direction, its strain value, and its evolution. The deformation map was divided into areas corresponding to individual active twin systems, enabling the analysis of microstructure dependence of deformation behavior and twinning activity. The performance of the proposed twinning identification approach was evaluated by accuracy, precision, and sensitivity metrics. The effect of the tuning parameters used in the algorithm on the performance is also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Plasticity and fracture behavior of Inconel 625 manufactured by laser powder bed fusion: Comparison between as-built and stress relieved conditions

In this work, the influence of stress relief on the plasticity and fracture behavior of Inconel 625 fabricated through laser powder bed fusion additive manufacturing (AM) was investigated. The as-built versus stress relieved microstructures were compared, showing similar grain structures but the presence of ~10 vol % δ phase in the stress relieved condition, and no δ phase in the as-built condition. Mechanical tests under plane strain tension were performed on the stress relieved samples, and an anisotropic plasticity model was calibrated and validated using finite element simulations. Uniaxial and notched tension tests were performed on both as-built and stress relieved samples to probe the effect of stress relief on stress state- and direction-dependent fracture behavior. It was found that on average, the fracture strain of the stress relieved samples along the build direction was 30% higher than that along the perpendicular build direction in the stress state range studied, and the stress relief heat treatment resulted in a 45% decrease in fracture strain. The fracture strain in stress relieved samples was more strongly dependent on stress state than in as-built samples.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Boron capture stabilizing the diffusion barriers in a two-step Mo-Si-B coated refractory multi-principal element alloy

A Mo-Si-B based coating has been applied on a refractory multi-principal element alloy (RMPEA) using a two-step coating strategy and has endured more than 750 hours of thermal cycling oxidation exposure between room temperature to 1300°C with a minimal weight change. Here, the formation of the Mo 5 SiB 2 diffusion barrier in the coating prevents the inward diffusion of the coating components. Then, boron is captured by the RMPEA, resulting in the formation of a solid solution X 5 SiB 2 (X= W, Mo, Ta, Nb, V) layer and an RMPEA-B boride layer underneath it that acts as the second diffusion barrier.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Nanoscale serration characteristics of additively manufactured superalloys

Structural elements made of nickel-based superalloys usually operate at high temperatures. Many surface failure mechanisms such as creep, fatigue, fretting fatigue, corrosion, and stress corrosion cracking start from the surface. Thus, studying the surface mechanical properties and deformation behavior of materials is vital in order to draw a correlation between the surface properties and failures. Herein, a nanoindentation technique was implemented to characterize surface properties of a widely used additively manufactured (AM) superalloy, i.e., Inconel 625. The specimens were tested in a range of temperatures in a vacuum chamber. Serrated plastic flow characterized by pop-in events during nanoindentation, known as Portevin-Le Chatelier (PLC) effect, was observed in all three tested elevated temperatures. This phenomenon depicts itself as bursts of plasticity in the loading section of the load-displacement curves. These bursts were studied comprehensively to explore incipient plasticity. Hertzian contact mechanics were implemented to extract the maximum shear stress beneath the indenter from the pop-in loads. The results show that the initial pop-in load increases as the temperature increases. The average initial pop-in load increases by almost four times from 300 °C to 650 °C. This was attributed to the formation of strengthening precipitates. The average size of the serrations and the magnitude of dislocation nucleation increase from 300 °C to 500 °C and decrease from 500 °C to 650 °C. Finally, the serrations are attributed to the dislocation generation and movement as well as their interaction with the solute atoms and precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electro-strengthening of the additively manufactured Ti–6Al–4V alloy

Structure-property-processing relationship has been studied in additively manufactured Ti–6Al–4V alloy. The processing was performed using in-situ electron microscope (EM) at a moderate current density of 5 × 105 A/cm2 applied for 5 min, and by suppressing Joule heating with massive heat sinks such that the temperature rise was <180 °C and the mechanical properties were not compromised. Overall, the results show that while the grain size increased by ~15%, the nanohardness increased by 16%. This is attributed to the pronounced dislocation generation, regeneration, and clustering as well as defect healing. Ultimately, there is a reduction in the residual strain and a significant increase in the intrinsic strength as evidenced by the high Taylor factor of the electric current processed specimen. This novel processing technique represents an alternative pathway for active controlling of microstructure and internal defects for parts that might be sensitive to high-temperature processing or conventional methods.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupled solute effects enable anomalous high-temperature strength and stability in nanotwinned Al alloys

Nanoprecipitates or grain refinement can effectively enhance the mechanical strength of Al alloys, but the room-temperature strengths of precipitation hardened and nanocrystalline Al alloys often fall below 1 GPa. Furthermore, they are largely plagued by precipitous mechanical softening at elevated temperature below 300°C, mostly due to degraded microstructural stability. Here, we report a mechanism of coupled solute effect in nanotwinned Al-Fe-Ti alloys that enables stability of nanograins up to 400°C and an unprecedented high-temperature flow stress of ~ 1.7 GPa at 300°C. The supersaturated Fe solutes in Al act as effective grain refiner, forming superstrong solid solution alloys. More importantly, empirical evidence combined with first principle calculations indicate that the Ti solutes delay the agglomeration of Fe solutes, thereby remarkably extending the temperature window for the stability of nanograins in nanotwinned Al alloys. Finally, this study highlights the opportunity to design ultrastrong and stable nanostructured alloys for potential high temperature applications via a coupled solute effect.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Quantitative study of the effect of grain boundary parameters on the slip system level Hall-Petch slope for basal slip system in Mg-4Al

Several theoretical studies have reported that the geometry and structure of grain boundaries in polycrystalline materials could impose a significant effect on the Hall-Petch slope. However, experimental observations are primarily limited by the ability of the techniques to accurately quantify the grain boundary strength and validate these theoretical models. Using high-resolution electron backscatter diffraction (HR-EBSD), the local stress tensor ahead of a slip band blocked by a grain boundary was quantified and coupled with a continuum dislocation pile-up model to assess the barrier strength of specific grain boundaries to specific slip systems, referred to as micro-Hall-Petch coefficient. For basal slip system in a deformed Mg-4Al alloy, the micro-Hall-Petch coefficient ($k^{basal}_{μ}$) varied significantly, from 0.054 to 0.184 MPa - m 1/2 for nine different grain boundaries. These results were correlated with geometric descriptors of the respective grain boundaries, with three-dimensional GB profile additionally measured via focused ion beam milling. It was found that the angle between the two slip plane traces on the grain boundary plane was the most sensitive parameter affecting $k^{basal}_{μ}$, followed by the angle between the slip directions. A functional form for calculation of $k^{basal}_{μ}$ depending on these two angles is proposed to augment crystal plasticity constitutive models with slip resistance dependent on some measure of the grain size. The method allows a new pathway to calibrate grain size strengthening parameters in crystal plasticity models, allowing further computational investigations of the interrelationship between texture, grain morphology, and the Hall Petch effect.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Oxidation behavior of Fe-Cr-2Si alloys in high temperature steam

FeCrSi alloys have been proposed as alternatives to FeCrAl alloys for accident-tolerant fuel cladding in light water reactors. Experiments on the oxidation resistance of three Fe-Cr-2Si alloys in high-temperature steam, with 12, 16, and 20 wt. % Cr, show that ≥16 % Cr is sufficient to form a thin, passivating, binary oxide layer. Additionally, at 1200 °C, only Cr 2 O 3 and SiO 2 form on Fe 16 Cr 2 Si and Fe 20 Cr 2 Si, while additional ternary Fe oxides form on Fe 12 Cr 2 Si. Decohesion and spalling of oxide were observed on Fe-Cr-Si alloys exposed to steam at 900 °C and above. Fe 20 Cr 2 Si exhibits the best oxidation resistance of the three in high-temperature steam.

36 MATERIALS SCIENCE↗