Interface engineering of lithium metal anodes via atomic and molecular layer deposition
Atomic and molecular layer deposition (ALD and MLD) are two promising tools for practicing interface engineering of lithium metal anodes precisely.
Chemistry↗
SEARCH · Search NASA
Results for “molecular layer”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Transformational Molecular Layer Deposition Tailor-Made Size-Sieving Sorbents for Post-Combustion CO 2 Capture
This report summarizes the carbon capture research and development conducted by The State University of New York at Buffalo (UB), University of South Carolina (USC), GTI Energy (GTI), and Rensselaer Polytechnic Institute (RPI) for U.S. Department of Energy (DOE) project DE-FE0031730 titled “Transformational Molecular Layer Deposition Tailor-made Size-Sieving Sorbents for Post-Combustion CO 2 capture.” The objective of this project was to develop a transformational molecular layer deposition (MLD) tailor-made size-sieving sorbent integrated with a pressure swing adsorption (PSA) cycle schedule that can be installed in new or retrofitted into existing pulverized coal (PC) power plants for CO 2 capture with a cost of electricity at least 30% lower than a supercritical PC power with CO 2 capture, or approximately $\$$30 per tonne of CO 2 captured, and with it being ready for demonstration by 2030.
20 FOSSIL-FUELED POWER PLANTS↗
Mild-Annealed Molecular Layer Deposition (MLD) Tincone Thin Film as Photoelectrochemically Stable and Efficient Electron Transport Layer for Si Photocathodes
Metalcone thin films, composed of inorganic–organic hybrids, are synthesized using molecular layer deposition (MLD) through reactions between organometallic precursors (e.g., Sn, Al, and Ti) and organic reactants (e.g., ethylene glycol and glycerol). Despite their unique properties, metalcones exhibit significant vulnerability to water due to their organic components, limiting their potential in electrochemical applications. This study focuses on enhancing the photoelectrochemical stability of tincone thin films in aqueous electrolyte while preserving their hybrid characteristics through mild annealing in air at 250 °C. As-deposited and vacuum-annealed tincone thin films exhibited significant degradation under these conditions, while high-temperature-annealed (500 °C) tincone thin films offered improved stability with a significant decline in charge transfer efficiency. In contrast, mild annealing in air maintained the C–O bond at half level and improved the stability and charge transport without compromising the unique characteristics of tincone. This was confirmed by ellipsometry, X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR). Mild-annealed tincone deposited on a lightly doped p-type silicon (p-Si) photocathode produced a 20-fold increase in CO volume compared to high-temperature annealed tincone in a CO 2 -saturated potassium bicarbonate (KHCO 3 ) electrolyte with dispersed graphene oxide–cobalt phthalocyanine (GO-CoPc) under 1 sun illumination at 0.9 V vs reversible hydrogen electrode (RHE), while maintaining the faradaic efficiency for CO and H 2 . These results suggest that mild-annealed tincone thin films hold significant potential as protective charge transport layers on silicon photocathodes for the aqueous CO 2 reduction reaction (CO 2 RR).
Annealing (metallurgy)↗
Effect of Networking Density on the Patterning Performance of Molecular Layer Deposited Alucone Electron Beam/EUV Resists
One of the main barriers to continued device scaling in the era of extreme ultraviolet (EUV) lithography is the need for improved photoresist chemistries to address challenges such as poor EUV sensitivity, inadequate etch resistance, and pattern collapse. Metal-organic photoresists are a promising class of materials that can address many of these challenges, and among them, resists deposited via hybrid molecular layer deposition (MLD) have attracted interest for their unique advantages in thickness control, chemical homogeneity, and compatibility with vacuum processing. However, despite many successful demonstrations of patterning, little is known about how the molecular design of hybrid MLD resists affects their lithographic performance. In this work, we study the effect of the network structure, a common feature among all hybrid MLD resists, via a series of aluminum alkoxide ("alucone") negative tone resists with varying networking density. Their patterning mechanism is investigated via electron beam lithography (EBL)─a common proxy for EUV─and compared to their EUV-induced reactions studied via flood exposure and in situ characterization. In conclusion, we show that the resist with the least networking density demonstrates the best sensitivity and resolution, with the ability to resolve dense line/space gratings as small as 14 nm half pitch via EBL.
electron beam lithography↗
Molecular Layer Deposited Aluminum‐Based Hybrid Resist for High‐Resolution Nanolithography and Direct Ultra‐High Aspect Ratio Pattern Transfer
Inorganic-containing hybrid photoresists are critical for next-generation extreme ultraviolet (EUV) lithography and angstrom-era semiconductor miniaturization. However, associated conventional solution processing struggles to achieve ultrathin, uniform films with high conformality and compositional control, limiting overall patterning performance. Here, this study reports the systematic lithographic patterning characterization of an Al-based hybrid resist synthesized via vapor-phase molecular layer deposition (MLD), using the trimethylaluminum (TMA) metal precursor and the hydroquinone (HQ) aromatic organic linker. The resist supports both sub-20 nm high-resolution nanolithography and virtually infinite silicon plasma etch selectivity. Lithographic performance studied using electron beam lithography (EBL) as a proxy for EUV shows that, under an optimized process adopting post-exposure bake, the resist achieves the best resolution of 15.4 nm linewidth under stringent 1:1 line-space high-density patterning—limited only by the minimum beam size of the EBL system. The resist also shows wide dose latitude and balanced performance in resolution, roughness, and sensitivity. The infinite silicon etch selectivity, stemming from spontaneous aluminum oxyfluoride passivation layer formation, enables fabrication of micrometer-tall, 40 nm-wide silicon nanofin structures using only a ≈30 nm-thick resist layer, without no hard mask. These results highlight the potential of MLD-based hybrid resists for developing next-generation resist materials for micro/nanoelectronics manufacturing.
36 MATERIALS SCIENCE↗
Light-Mediated Contact Printing of Phosphorus Species onto Silicon Using Carbene-Based Molecular Layers
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Modulating spin-valley relaxation in WSe 2 with variable thickness VOPc layers
Combining the synthetic tunability of molecular compounds with the optical selection rules of transition metal dichalcogenides (TMDCs) that derive from spin-valley coupling could provide interesting opportunities for the readout of quantum information. However, little is known about the electronic and spin interactions at such interfaces and the influence on spin-valley relaxation. Here, in this work, vanadyl phthalocyanine (VOPc) molecular layers are thermally evaporated on WSe 2 to explore the effect of molecular layer thickness on excited-state spin-valley polarization. The thinnest molecular layer supports an interfacial state which destroys the spin-valley polarization almost instantaneously, whereas a thicker molecular layer results in longer-lived spin-valley polarization than the WSe 2 monolayer alone. The mechanism appears to involve a tightly bound species at the molecule/TMDC interface that strengthens exchange interactions and is largely avoided in thicker VOPc layers that isolate electrons from WSe 2 holes.
2D materials↗
Lithicone‐Protected Lithium Metal Anodes for Lithium Metal Batteries with Nickel‐Rich Cathode Materials
The high energy density advantage of lithium (Li) metal batteries (LMBs) makes them increasingly desirable; however, problems such as strong reactivity and dendrite growth of Li metal anode limit their practical uses. In this work, a novel Li‐containing glycerol (LiGL) or lithicone protection layer on a 50 μm thick Li metal anode is employed for improving the performance of LMBs. This LiGL layer was accurately deposited via a molecular layer deposition (MLD) process at 150 °C, using lithium tert‐butoxide and glycerol as precursors. The as‐formed LiGL coating layer is highly tunable in its thickness by simply adjusting MLD cycles and shows a good stability and outstanding ionic transport properties. The LiGL layer is found to effectively mitigate side reactions and enhance cycling stability in both symmetric cells and full cells. Specifically, the LMBs with LiGL@Li anode of 400 MLD cycles and LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode enable a capacity retention of ≈87%, much higher than ≈35% of the cells with bare Li after 200 cycles at a charge/discharge current density of 2.1 mA cm −2 . This work paves a feasible way for practical LMBs with improved capacity and stability through applying an innovative protection layer on Li metal anodes.
25 ENERGY STORAGE↗
A novel polymeric lithicone coating for superior lithium metal anodes
Lithium metal (Li) is commonly regarded as the “holy grail” of rechargeable batteries and can serve as anodes for constituting various high-energy lithium metal batteries (LMBs). However, it suffers from two notorious issues: (1) continuous formation of inhomogeneous solid electrolyte interphase and (2) Li dendritic growth. Here, in this study, we developed a novel polymeric lithicone via a new molecular layer deposition (MLD) process, using lithium tert-butoxide (LTB) and hydroquinone (HQ) as precursors. We revealed that such an MLD process enabled the resultant LiHQ to grow linearly in a highly controllable and cyclic mode at a growth rate of 4 Å cycle −1 . Furthermore, its low process deposition temperature of 150 °C made it possible to practice high-quality coatings over Li anodes directly. We demonstrated that, very compellingly, this LiHQ coating could protect Li anodes from corrosion and dendritic growth. As a consequence, this LiHQ coating has enabled Li||Li symmetric cells an extremely long cyclability up to 8000 Li-plating/stripping cycles without failure. More excitingly, we demonstrated that, coupled with LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathodes, the LiHQ-modified Li anodes could help the resultant Li||NMC811 realize a much better capacity retention and much longer cyclability. Thus, this study represents a strategic route for developing commercializeable LMBs.
25 ENERGY STORAGE↗
Harnessing Quantum Capacitance in 2D Material/Molecular Layer Junctions for Novel Electronic Device Functionality
Two-dimensional (2D) materials promise advances in electronic devices beyond Moore’s scaling law through extended functionality, such as non-monotonic dependence of device parameters on input parameters. However, the robustness and performance of effects like negative differential resistance (NDR) and anti-ambipolar behavior have been limited in scale and robustness by relying on atomic defects and complex heterojunctions. In this paper, we introduce a novel device concept that utilizes the quantum capacitance of junctions between 2D materials and molecular layers. We realized a variable capacitance 2D molecular junction (vc2Dmj) diode through the scalable integration of graphene and single layers of stearic acid. The vc2Dmj exhibits NDR with a substantial peak-to-valley ratio even at room temperature and an active negative resistance region. The origin of this unique behavior was identified through thermoelectric measurements and ab initio calculations to be a hybridization effect between graphene and the molecular layer. The enhancement of device parameters through morphology optimization highlights the potential of our approach toward new functionalities that advance the landscape of future electronics.
2D materials↗
Enhanced Performance of Silicon Anodes through Hybrid Surface Engineering
Silicon (Si) is a promising anode material for nextgeneration lithium-ion batteries (LIBs) due to its high theoretical capacity. However, Si-containing anodes typically suffer from unacceptably short lives because of the unrestricted growth of the solid electrolyte interphase (SEI). Here, in this study, hybrid surface coatings are developed to stabilize the SEI in high loading pure Si anodes using atomic and molecular layer deposition. The coatings, consisting of LiF paired with lithicone, create an ionically conductive surface that enhances the capacity retention, rate performance, and longevity. Careful binder selection helps demonstrate the full utility of the coatings by enabling high loading electrodes to cycle continuously at current densities of 1200 mA/g Si . Uncoated controls, in comparison, fail within just 10 cycles at lower loadings. X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy are used to provide supporting evidence of the coating composition and efficacy. The data indicate that our lithicone coating is converted to Li 2 CO 3 upon cycling contributing to favorable LiF/Li 2 CO 3 interfaces that enhance the space-charge effect at the active material’s surface. When applied to electrodes made with thermally stable binders and increasingly higher loadings (approaching 5 mAh/cm 2 ), ion transport through the bulk electrode, rather than SEI growth, is shown to be the limiting factor. Furthermore, data suggests a favorable interaction between lithicone precursors and poly(acrylic acid) binders mitigates thermal decomposition at higher temperatures. The work presented here represents the successful realization of composite coatings containing LiF/Li 2 CO 3 components to stabilize high-loading Si anodes. This work helps inform advanced surface engineering strategies to achieve highly reversible, high-capacity Si anodes capable of fast charging for high-performance LIBs.
atomic layer deposition↗
Characterization of Polyamide Thin Films by Atomic Force Microscopy
This study directly compares the mechanical behavior of novel molecular layer deposition (MLD) and analogous interfacial polymerization (IP) polyamide thin films in environments relevant to reverse osmosis (RO) membrane operation. The elastic modulus of the films was determined using atomic force microscopy (AFM) in dry, hydrated, and chlorinated states. Surface roughness characteristics were also obtained given their potential influence on AFM modulus measurements. The much smoother MLD films demonstrated a statistically higher modulus in all states as compared to their IP counterparts. The MLD films maintained a modulus ~3X and ~5X greater than that of IP films after hydration and chlorination, respectively. Such differences in behavior may be due to the higher density and correspondingly lower void content of the MLD films. Results from this study provide a rationale for future development of MLD for fabrication of polyamide films for incorporation in RO membranes.
atomic force microscopy↗
Single-Layer Magnet Phase in Intrinsic Magnetic Topological Insulators, [MnTe][Bi 2 Te 3 ] n , Far beyond the Thermodynamic Limit
The intrinsic magnetic topological insulator (IMTI) family [MnTe][Bi 2 Te 3 ]n has demonstrated magneto-topological properties dependent on n, making it a promising platform for advanced electronics and spintronics. However, due to technical barriers in sample synthesis, their properties in the large n limit remain unknown. To overcome this, we utilized the atomic layer-by-layer molecular beam epitaxy (ALL-MBE) technique and achieved IMTIs with n as large as 15, far beyond that previously reported in bulk crystals or thin films. Then, we discover that the “single-layer magnet (SLM)” phase, primarily determined by intralayer ferromagnetic coupling, emerges for n > ∼4 and remains little affected up to n = 15. Nonetheless, still, nonzero, interlayer ferromagnetic coupling is necessary to stabilize the SLM phase, suggesting that the SLM phase eventually disappears in the n → ∞ limit. This study uncovers the secrets of IMTIs beyond the thermodynamic limit and opens a door to diverse magneto-topological applications.
2D ferromagnets↗
Intercalation-Induced Amorphization Boosts Aqueous Magnesium-Ion Storage
The design of aqueous battery cathode materials that can store divalent ions with high capacity and satisfactory reversibility is of great technical importance and challenge. Here, we report that divalent Mg 2+ storage is facilitated by an intercalation-induced amorphization of vanadate electrode materials. Electrokinetic analyses and in situ synchrotron X-ray diffraction and absorption spectroscopy collectively demonstrate that vanadate layered materials (Li–V 3 O 8 ) undergo a structural transformation to amorphization induced by Mg 2+ intercalation, and a reversible restoration of crystalline structure upon Mg 2+ deintercalation. Debye scattering simulations suggest that intercalation-induced turbostratic disorder, especially random rotations, translational shifts, oscillatory motions, or varied interlayer spacing of adjacent V–O molecular layers, could be responsible for the observed amorphization. The highly distorted local structure, in turn, facilitates Mg 2+ intercalation across the vanadate electrode materials, responsible for nearly 3/7 of the total Mg 2+ ions intercalated. The study presented reveals an intriguing relationship between ion transport and the reversible amorphization-to-crystallization dynamics it induces, opening a paradigm for designing advanced aqueous battery electrodes.
36 MATERIALS SCIENCE↗
Ultrafast Formation of Charge Transfer Trions at Molecular‐Functionalized 2D MoS 2 Interfaces
In this work, we investigate trion dynamics occurring at the heterojunction between organometallic molecules and a monolayer transition metal dichalcogenide (TMD) with transient electronic sum frequency generation (tr-ESFG) spectroscopy. By pumping at 2.4 eV with laser pulses, we have observed an ultrafast hole transfer, succeeded by the emergence of charge-transfer trions. This observation is facilitated by the cancellation of ground state bleach and stimulated emission signals due to their opposite phases, making tr-ESFG especially sensitive to the trion formation dynamics. The presence of charge-transfer trion at molecular functionalized TMD monolayers suggests the potential for engineering the local electronic structures and dynamics of specific locations on TMDs and offers a potential for transferring unique electronic attributes of TMD to the molecular layers.
Time-resolved↗
Adsorption, Orientation, and Speciation of Amino Acids at Air–Aqueous Interfaces for the Direct Air Capture of CO 2
Amino acids make up a promising family of molecules capable of direct air capture (DAC) of CO 2 from the atmosphere. Under alkaline conditions, CO 2 reacts with the anionic form of an amino acid to produce carbamates and deactivated zwitterionic amino acids. The presence of the various species of amino acids and reactive intermediates can have a significant effect on DAC chemistry, the role of which is poorly understood. In this study, all-atom molecular dynamics (MD) based computational simulations and vibrational sum frequency generation (vSFG) spectroscopy studies were conducted to understand the role of competitive interactions at the air–aqueous interface in the context of DAC. We find that the presence of potassium bicarbonate ions, in combination with the anionic and zwitterionic forms of amino acids, induces concentration and charge gradients at the interface, generating a layered molecular arrangement that changes under pre- and post-DAC conditions. In parallel, an enhancement in the surface activity of both anionic and zwitterionic forms of amino acids is observed, which is attributed to enhanced interfacial stability and favorable intermolecular interactions between the adsorbed amino acids in their anionic and zwitterionic forms. The collective influence of these competitive interactions, along with the resulting interfacial heterogeneity, may in turn affect subsequent capture reactions and associated rates. Finally, these effects underscore the need to consider dynamic changes in interfacial chemical makeup to enhance DAC efficiency and to develop successful negative emission and storage technologies.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Ultrafast Formation of Charge Transfer Trions at Molecular‐Functionalized 2D MoS 2 Interfaces
Abstract In this work, we investigate trion dynamics occurring at the heterojunction between organometallic molecules and a monolayer transition metal dichalcogenide (TMD) with transient electronic sum frequency generation (tr‐ESFG) spectroscopy. By pumping at 2.4 eV with laser pulses, we have observed an ultrafast hole transfer, succeeded by the emergence of charge‐transfer trions. This observation is facilitated by the cancellation of ground state bleach and stimulated emission signals due to their opposite phases, making tr‐ESFG especially sensitive to the trion formation dynamics. The presence of charge‐transfer trion at molecular functionalized TMD monolayers suggests the potential for engineering the local electronic structures and dynamics of specific locations on TMDs and offers a potential for transferring unique electronic attributes of TMD to the molecular layers.
Jing, Yuancheng↗
Single-Atom Doping at the Molecule–Metal Interface: How Rh Affects Surface Explosion Kinetics
Controlling chemical reactions at interfaces is central to many fields, including atmospheric, environmental, and biological chemistry as well as catalysis and corrosion. We performed a fundamental study of how catalytically active Rh atoms placed at and above a molecule-metal interface influence the surface reaction kinetics of tartaric acid (TA) decomposition. Specifically, TA decomposition on Cu(100) exhibits autocatalytic decomposition kinetics involving a slow initiation step followed by fast decomposition of the molecular layer. These so-called “surface explosions” are extremely sensitive to initial conditions, making it fundamentally interesting to study how the placement of reactive atoms affects the reaction rate. Temperature-programmed reaction (TPR) experiments reveal that Rh atoms embedded in the Cu(100) surface beneath TA (TA/Rh/Cu) or atop the TA layer (Rh/TA/Cu) reduce the decomposition temperature and modify the reaction rate constants. Isothermal TPR analysis reveals that Rh enhances both the initiation rate constant, k i , and the explosion rate constant, k e , facilitating explosive decomposition at lower temperatures. This result provides evidence that both the initiation and explosion steps occur at the metal-molecule interface and are accelerated by the presence of Rh at this interface. This study illustrates how small amounts of reactive elements may be used to control nonlinear kinetic processes at interfaces.
desorption↗