SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Junctions formed from materials that contain mobile charged species and fixed counterions can assist in photo-induced charge separation and lead to photovoltaic action, irrespective of whether the mobile charges are electronic or protonic.
Explore the source record for details and available documents.
Effective surface passivation of crystalline silicon (c-Si) surface by reducing the carrier recombination rate has led to modern c-Si solar cells with efficiencies > 25% in both laboratory and industrial settings. Typical mainstream surface passivation techniques include high-temperature silicon oxide (SiOx), amorphous silicon (a-Si:H), hydrogen-rich silicon nitride (SiNx), and aluminum oxide (Al2O3) [1]. They have demonstrated excellent surface recombination velocity of < 1 cm/s owing to both chemical passivation (via the hydrogen saturation of Si dangling bonds at the c-Si surface), and field-effect passivation (via the band bending from the fixed charge of the dielectric layers). Recently, several groups have studied solution-based organic materials for c-Si passivation, including bis(trifluoromethane)sulfonimide (TFSI), polystyrenesulfonate, and Nafion [2, 3] via spin or dip coating. All films were processed at ambient room temperature, and a high lifetime of 12 ms, as well as a low saturation current density (J0) of 16 fA/cm2, have been demonstrated using Nafion passivation [2]. However, despite the air instability, Nafion has several advantages when introduced to PV applications: (a) Wafer quality can be measured at high throughput after several process stages. (b) It is compatible with PL mapping, compared to HF liquid passivation which cannot be performed in room ambient. (c) Nafion process is fast and poses fewer constraints on process complexity, and cleanness, compared to Al2O3 and a-Si:H passivation. (d) Nafion is the ideal room temperature passivation, which can be applied onto a small fragment of a degraded module to investigate microscopic mechanisms when studying degradation mechanisms. Edge passivation is needed for advanced characterization tests such as Electron Paramagnetic Resonance (EPR), Electrically Detected Magnetic Resonance (EDMR), Deep Level Transient Spectroscopy (DLTS), local cell current-voltage (J-V), and Suns-Voc. In such cases, the laser-damaged minicell edges will obscure the true degradation mechanisms, and Nafion can effectively passivate them without causing further degradation through elevated-temperature processes. In this contribution, we show the passivation results of Nafion on bare nCz and compare it with a Al2O3 witness. We highlight the importance of edge pre-treatment before Nafion to achieve good passivation. We show that Nafion can reach decent passivation without undergoing high-temperature processes. We also explore the temperature dependency of Nafion through photoluminescence (PL) study and demonstrate the application of Nafion under cryogenic temperature (~6 K) through EPR. Our results reveal that Nafion can reduce surface and edge Si dangling bonds at low temperatures. Thus, it can be used as an effective room temperature passivation technique for advanced characterization methods.
X-ray photoelectron spectroscopy (XPS) is one of the most common techniques used to analyze the surface composition of catalysts and support materials used in polymer electrolyte membrane (PEM) fuel cells and electrolyzers, providing important insights for further improvement of their properties. Characterization of catalyst layers (CLs) is more challenging, which can be at least partially attributed to the instability of ionomer materials such as Nafion during measurements. This work explores the stability of Nafion during XPS measurements, illuminating and addressing Nafion degradation concerns. The extent of Nafion damage as a function of XPS instrumentation, measurement conditions, and sample properties was evaluated across multiple instruments. Results revealed that significant Nafion damage to the ion-conducting sulfonic acid species (>50% loss in sulfur signal) may occur in a relatively short time frame (tens of minutes) depending on the exact nature of the sample and XPS instrument. This motivated the development and validation of a multipoint XPS data acquisition protocol that minimizes Nafion damage, resulting in reliable data acquisition by avoiding significant artifacts from Nafion instability. The developed protocol was then used to analyze both thin film ionomer samples and Pt/C-based CLs. Comparison of PEM fuel cell CLs to Nafion thin films revealed several changes in Nafion spectral features attributed to charge transfer due to interaction with conductive catalyst and support species. This study provides a method to reliably characterize ionomer-containing samples, facilitating fundamental studies of the catalyst-ionomer interface and more applied investigations of structure-processing-performance correlations in PEM fuel cell and electrolyzer CLs.
Colloidal Nafion morphology plays a critical role in determining the performance of fuel cells and electrolyzers. While small-angle neutron scattering (SANS) studies previously described Nafion in liquid media as dispersed cylinders, the analysis remains nonunique with multiple possible morphological descriptions of the data. Here, using SANS and all-atomistic molecular dynamics, we confirm that Nafion morphology in liquid media differs substantially depending on dispersing agent and dispersion method. H + Nafion dispersed in N-methyl pyrrolidone forms swollen cluster particles with physically cross-linked ionic groups. Scattering profiles from dispersed Nafion membrane have a large structure factor feature not observed for redispersed Nafion D-521. H + Nafion dispersed in water has a highly elongated cylindrical morphology (radius = 10 ± 1.5 Å, height = 358 ± 4.7 Å) with fully dissociated and solvated sulfonic acid groups on the particle wall. In conclusion, these results highlight an important discrepancy between the methods of preparing Nafion dispersions and the use of simplified analysis techniques to describe Nafion morphology.
We developed a new approach to attach particles onto a conductive layer as a working electrode (WE) in a microfluidic electrochemical cell with three electrodes. Nafion, an efficient proton transfer molecule, is used to form a thin protection layer to secure particle electrodes. Spin coating is used to develop a thin and even layer of Nafion membrane. The effects of Nafion (5 wt% 20 wt%) and spinning rates were evaluated using multiple sets of replicates. The electrochemical performance of various devices was demonstrated. Additionally, the electrochemical performance of the devices is used to select and optimize fabrication conditions. The results show that a higher spinning rate and a lower Nafion concentration (5 wt%) induce a better performance, using cerium oxide (CeO2) particles as a testing model. The WE surfaces were characterized using atomic force microscopy (AFM), scanning electron microscopy-focused ion beam (SEM-FIB), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and X-ray photoelectron spectroscopy (XPS). The comparison between the pristine and corroded WE surfaces shows that Nafion is redistributed after potential is applied. Our results verify that Nafion membrane offers a reliable means to secure particles onto electrodes. Furthermore, the electrochemical performance is reliable and reproducible. Thus, this approach provides a new way to study more complex and challenging particles, such as uranium oxide, in the future.
Here, in monocrystalline Si (c-Si) solar cells, identification and mitigation of bulk defects are crucial to achieving a high photoconversion efficiency. To spectroscopically detect defects in the c-Si bulk, it is desirable to passivate the surface defects. Passivation of the c-Si surface with dielectrics such as Al 2 O 3 and SiNx requires deposition at elevated temperatures, which can influence defects in the bulk. Herein, we report on the passivation of different Czochralski (Cz) Si wafer surfaces by an organic copolymer, Nafion. We test the efficacy of the surface passivation at temperatures ranging from 6 to 473 K to detect bulk defects using electron paramagnetic resonance (EPR) spectroscopy. By comparing with state-of-the-art passivation layers, including Al 2 O 3 and liquid HF/HCl, we found that at room temperature, Nafion can provide comparable passivation of n-type Cz Si with an implied open-circuit voltage (iV oc ) of 713 mV and a recombination current prefactor J o of 5 fA/cm 2 . For p-type Cz Si, we obtained an iV oc of 682 mV with a J o of 22.4 fA/cm 2 . Scanning electron microscopy and photoluminescence reveal that Nafion can also be used to passivate the surface of c-Si solar cell fragments scribed from a solar cell module by using a laser. Consistent with previous studies, analysis of the EPR spectroscopy data confirms that the H-terminated surface is necessary, and fixed negative charge in Nafion is responsible for the field-effect passivation. While the surface passivation quality was maintained for almost 24 h, which is sufficient for spectroscopic measurements, the passivation degraded over longer durations, which can be attributed to surface SiO x growth. These results show that Nafion is a promising room-temperature surface passivation technique to study bulk defects in c-Si.
Ionomers act as the solid polymer electrolyte membrane in many modern electrochemical devices, yet the role of their nanostructure in modulating the poroelastic response remains poorly understood, especially in liquid water, where few techniques can measure simultaneous transport-mechanical properties. Poroelastic Relaxation Indentation (PRI) is uniquely suited for measuring time-dependent transport-mechanical properties of porous solids, specifically hydraulic diffusivity, elastic modulus, Poisson’s ratio, and intrinsic permeability, for porous solids. While ionomers such as Nafion are not porous in the typical sense, Nafion has a nanophase-segregated structure that, when fully swollen in liquid water, behaves as a poroelastic solid with a coupled mechanical-transport response. Using a poroelastic framework, we investigate how casting and pretreatment of Nafion membranes alter their poroelastic response in liquid environments. We characterize both extruded and dispersion-cast Nafion membranes pretreated in water at 25 or 100 °C and relate the mechanical-transport properties to the ionomer structure via hydrophilic and intercrystalline domain spacing measured using Small-Angle X-ray Scattering (SAXS). At 25 °C, dispersion-cast membranes exhibit distinctly lower hydraulic diffusivity and intrinsic permeability than extruded membranes but with comparable mechanical properties. Pretreatment at 100 °C increases hydrophilic domain spacing, improving transport but at the expense of mechanical stiffness. Dispersion-cast membranes respond more strongly to pretreatment than extruded membranes. Using the Carman-Kozeny pore network model and the hydrophilic domain-spacing, we estimate the pore radius and tortuosity to show how pretreatment reduces structure-related tortuosity differences between dispersion-cast and extruded membranes. Here, in this work, we show that nanophase-segregated materials such as Nafion can be rigorously characterized using poroelasticity, resulting in physically meaningful transport-mechanical properties. Coupling PRI with SAXS provides insights into the nanostructural features that govern the coupled mechanical-transport response. By establishing PRI for a nanophase-segregated material, this approach opens avenues for this technique’s application in other hydrated polymeric materials not typically considered to be poroelastic.
Driven by environmental and health concerns related to per- and polyfluoroalkyl substances (PFAS), there has been growing interest in developing fluorine-free proton (H + ) exchange membrane (PEM) materials for fuel cells and water electrolyzers. In this study, we present a side-by-side comparison of the key transport properties of submicron thick, PFAS-free amorphous silicon dioxide (SiO 2 ) membranes to Nafion, a fluorinated polymer electrolyte membrane that represents the industry standard for PEM fuel cells and electrolyzers. Here, measurements of proton (H + ) conductivity (σ H + ), hydrogen (H 2 ) permeability (P H 2 ), and electrical resistivity (ρ e – ) were conducted using model thin films comprised of SiO 2 membranes deposited by atomic layer deposition (ALD). Although the H + conductivity of the SiO 2 membranes is 2–3 orders of magnitude lower than Nafion, the addition of phosphorus dopants (PO x ) improves H + conductivity such that the area specific membrane resistance of thin (<50 nm) PO x -doped SiO 2 membranes is more than an order of magnitude lower than Nafion-117. Importantly, the safe operation of such nanoscale membranes within a PEM electrolyzer is feasible thanks to the low H 2 permeability of dense SiO 2 -based membranes, which are predicted to limit H 2 crossover rates to acceptable levels for pressures up to ≈ 100 bar. As a proof-of-principle demonstration, a chip-scale water electrolyzer based on 100 nm thick PO x -SiO 2 membrane is shown to achieve a current density of 2 A cm –2 at a potential of 2.5 V. If this technology can be successfully scaled up, H + conducting oxide membranes offer an attractive PFAS-free alternative to Nafion for efficient and durable water electrolysis and fuel cell technologies.
Scaling up clean-energy applications necessitates the development of platinum group metal (PGM)-free fuel cell electrocatalysts with high activity, stability, and low cost. Here, X-ray absorption (XAS) at the Fe K-edge and Fe K β X-ray emission (XES) spectroscopies were used to study the electronic structure of Fe centers in highly active Fe–N–C oxygen reduction catalysts with significant commercial potential. X-ray absorption near-edge structure (XANES) analysis has shown that the majority (>95%) of Fe centers are in the Fe 3+ oxidation state, while extended X-ray absorption fine structure (EXAFS) detected a mixture of single site Fe–N 4 centers (>95%) and centers with short (~2.5 Å) Fe–Fe interactions of Fe metal and/or Fe-carbide nanoparticles (<5%) featuring the Fe o oxidation state. Surprisingly, addition of Nafion, the most widely used ionomer, resulted in pronounced changes in the XAS spectra, consistent with a strong catalyst–ionomer interaction where long Fe–Fe interactions at ~3.1 Å were shown to be a feature of Fe 3+ ions bound with the Nafion. We conclude that exposure to Nafion during the device formulation has a different effect from the aggressive acid leaching typically used in the preparation of Fe–N–C catalysts. Furthermore, it was hypothesized that the polymer interacts with single sites’ Fe 3+ centers, as well as with graphene layers protecting the Fe o nanoparticles, and extracts some Fe ions into the Nafion matrix.
Nafion is a well-studied polymer of significant interest as a fuel cell membrane due to rapid transport of protons, which is often ascribed, at least in part, to its phase-separated morphology. The literature detailing ion sorption and transport in Nafion diverges considerably from that of water purification membranes, with contrasting analyses and models. To help bridge these gaps and facilitate comparisons of membranes with various structures, this study presents measurements of ion activity coefficients and sorption in Nafion 117 equilibrated with aqueous solutions of NaCl, MgCl 2 , and Na 2 SO 4 , which are relevant to water purification. The experimental data are compared to a theoretical framework based on Manning's counter-ion condensation theory and Donnan theory. Good agreement between the model and data is observed for NaCl and MgCl 2 , using no adjustable parameters. However, the model significantly underpredicts Na 2 SO 4 solubility, which is attributed to ion pairing effects. Furthermore, the results highlight the general applicability of counter-ion condensation theory to highly charged polymers, including those exhibiting nanoscale ordering, while revealing fundamental limitations related to ion pairing.
Here, we report on the effectiveness of sodium-exchanged Nafion membranes for inhibiting polysulfide crossover during redox flow battery operation. The solubility of polysulfides allows them to be used as a high-capacity catholyte for nonaqueous redox flow batteries (NARFB). The NARFB cathode capacity is controlled by the total tank catholyte volume and polysulfide concentration and, as such, is independent of polysulfide adsorption sites on carbon fibers or nanotubes as found within traditional Na or Li–S batteries. However, one of the major barriers to the realization of polysulfide NARFBs is associated with developing a robust membrane that has minimal polysulfide crossover under the operating conditions. We found that sodium-exchanged Nafion membrane separators effectively inhibit polysulfide crossover within a Na–sulfur NARFB. These membranes significantly improve both capacity retention (70%) and Coulombic efficiencies (99%) after 50 cycles. Commercial porous membranes showed a large crossover as detected by UV–vis spectroscopy and resulted in low capacity retention (20%) and Coulombic efficiency (74%) after 45 cycles. Electrochemical impedance spectroscopy (EIS) measurements highlighted the trade-off between innate reactivity and ionic conduction of the membranes. The results show that dense, single ion conducting Nafion enables a long cycle life; however, it reacts with Na metal to form a resistive passivation layer and increases the cell resistance. On the contrary, the open pore structure of Celgard allows for higher current charge/discharge, and its chemical nature is compatible with Na; however, it has a high degree of polysulfide crossover.
Proton-exchange-membrane water electrolyzer (PEMWE) catalyst layers consist of aggregates of catalyst particles (typically iridium) and ionomer (typically Nafion). Prior work suggests that the oxide form of Ir affects the kinetics of the oxygen-evolution reaction. However, because most catalyst-benchmarking studies are conducted ex situ in liquid electrolytes, it remains unclear how the ionomer is influenced by the catalyst oxide and affects overall cell performance. Using a suite of experimental techniques, we conduct fundamental investigations into model ink (catalyst and ionomer dispersed in solution) and thin-film systems to inform cell-level overpotential analysis as a function of three forms of Ir (metallic Ir m , oxyhydroxide IrOOH, and oxide IrO 2 ). Furthermore, nafion on Ir m has a high degree of phase separation and higher swelling, likely improving the ionic conductivity. Additionally, Nafion binds most strongly to IrOOH, likely yielding reduced kinetic overpotentials. These findings highlight the intricacies of the ionomer/Ir interface and provide insight into all catalyst-layer systems.
Polymer cation exchange membranes (CEMs) are widely used in water treatment processes. The fundamental factors that control the separation and selectivity of cations with different valences in CEMs are not fully understood. In this study, we use atomistic molecular dynamics simulations to investigate the underlying molecular mechanisms that control the mobility of cations with different valences in Nafion membranes. Our results indicate structural differences in binding of monovalent and divalent cations, which gives rise to differences in ion diffusion in Nafion. Monovalent cations are shown to be “territorially” bound, i.e., bound while partially hydrated, to the fixed charge groups whereas divalent cations are shown to be “site” bound, i.e., bound while fully dehydrated, to the charge groups on the polymer. This difference in binding structure gives rise to differences in transport characteristics of cations in Nafion.
Infrared and Raman spectroscopy techniques were applied to investigate the drying and aggregation behavior of Nafion ionomer particles dispersed in aqueous solution. Gravimetric measurements aided the identification of gel-phase development within a series of time-resolved spectra that tracked transformations of a dispersion sample during solvent evaporation. A spectral band characteristic of ionomer sidechain end group vibration provided a quantitative probe of the dispersion-to-gel change. For sets of attenuated total reflection Fourier transform infrared (ATR FT-IR) spectra, adherence to Beer's law was attributed to the relatively constant refractive index in the frequency region of hydrated –SO$^{–}_{3}$ group vibrations as fluorocarbon-rich ionomer regions aggregate in forming the structural framework of membranes and thin films. Although vibrational bands associated with ionomer backbone CF 2 stretching vibrations were affected by distortion characteristic of wavelength-dependent refractive index change within a sample, the onset of band distortion signaled gel formation and coincided with ionomer mass % values just below the critical gelation point for Nafion aqueous dispersions. Similar temporal behavior was observed in confocal Raman microscopy experiments that monitored the formation of a thin ionomer film from an individual dispersion droplet. For the ATR FT-IR spectroscopy and confocal Raman microscopy techniques, intensity in the water H–O–H bending vibrational band dropped sharply at the ionomer critical gelation point and displayed a time dependence consistent with changes in water content derived from gravimetric measurements. The reported studies lay groundwork for examining the impact of dispersing solvents and above-ambient temperatures on fluorinated ionomer transformations that influence structural properties of dispersion-cast membranes and thin films.
Oxycodone is a strong opioid frequently used as an analgesic. Although proven efficacious in the management of moderate to severe acute pain and cancer pain, use of oxycodone imposes a risk of adverse effects such as addiction, overdose, and death. Fast and accurate determination of oxycodone blood concentration would enable personalized dosing and monitoring of the analgesic as well as quick diagnostics of possible overdose in emergency care. However, in addition to the parent drug, several metabolites are always present in the blood after a dose of oxycodone, and to date, there is no electrochemical data available on any of these metabolites. In this paper, a single-walled carbon nanotube (SWCNT) electrode and a Nafion-coated SWCNT electrode were used, for the first time, to study the electrochemical behavior of oxycodone and its two main metabolites, noroxycodone and oxymorphone. Both electrode types could selectively detect oxycodone in the presence of noroxycodone and oxymorphone. However, we have previously shown that addition of a Nafion coating on top of the SWCNT electrode is essential for direct measurements in complex biological matrices. Therefore, in this work, the Nafion/SWCNT electrode was further characterized and used for measuring clinically relevant concentrations of oxycodone in buffer solution. The limit of detection for oxycodone with the Nafion/SWCNT sensor was 85 nM, and the linear range was 0.5–10 μM in buffer solution. Furthermore, this study shows that the fabricated Nafion/SWCNT sensor has potential to be applied in clinical concentration measurements.
Fourier Transform Infrared Spectroscopy is a valuable low-cost easy to use tool that has helped in understanding the structure and properties of Nafion as a function of environmental changes by closely monitoring the changes in vibrational modes of various functional groups in Nafion.
The formation of the main flue gas species (NOx, SOx, CO2, and CO) in pressurized oxy-fuel combustion can be fundamentally different from oxy-fuel combustion at atmospheric pressure. To accurately obtain the concentration of these gas species in a pressurized oxy-fuel combustor, a gas measurement which maintains the sampling pressure is needed. Very few published studies have accomplished this, and never under the conditions reported herein. In this work, we fire PRB coal in a 100 kWth staged pressurized oxy-fuel combustor (SPOC) under a pressure 15 bara. We utilize a state-of-the-art FTIR (Thermo Scientific Nicolet iS20) with a novel high-pressure gas cell that is under process pressure to measure the in-situ flue-gas concentration in a sampled flow. However, water vapor can significantly interfere with the FTIR measurement, particularly under pressure. To address this problem, we have developed a high-pressure nafion dryer to selectively remove the water vapor from the flue gas while retaining the flue gas species. This approach can significantly increase the signal-noise ratio for the FTIR. By integrating the nafion dryer and the high-pressure gas cell, we were able to successfully measure flue gas species at system pressure with the FTIR.