Search NASA⌕ Search

SEARCH · Search NASA

Results for “natural gas hydrates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Numerical simulation of gas production from natural gas hydrate deposits with multi-branch wells: Influence of reservoir properties

Vast amounts of natural gas hydrate are buried in subseafloor sediments without impermeable boundaries, which is recognized as an essential energy source for the future. Previously, the multi-branch well was proposed to enhance the recovery efficiency of natural gas hydrate, and the gas production rate has been dramatically improved comparing with the vertical well. However, the multi-branch well shows a terrible performance in gas production duration. Here, as a continuation of the previous study, numerical simulations were conducted to investigate the influence of hydrate reservoir properties on the gas production potential. Results indicate that it is hard to extract hydrate commercially for hydrate accumulations without impermeable boundaries. A high initial hydrate saturation leads to a long gas production duration but a low gas production rate. An increase in the intrinsic permeability of isotropic reservoirs would shorten the gas production duration and result in a low gas recovery ratio. Permeability anisotropy shows a noticeable effect on enhancing the gas recovery ratio and the gas production duration due to the improved pressure propagation pattern. Therefore, in the upcoming field tests, reservoir reconstructions that enhance permeability anisotropy are strongly suggested to obtain better outcomes.

03 NATURAL GAS↗
DOE OSTI2025

An experimental study on gas-liquid phase fluid migration in hydrate-bearing sediments during hydrate dissociation

Natural gas hydrate production tests face problems such as severe sand blockage, poor gas-liquid phase separation, and significant land subsidence. This is because of the insufficient understanding of the complex phase transition and gas-liquid multi-phase fluid migration during hydrate dissociation. In hydrate-bearing sediment systems, hydrate phase transition couples with gas-liquid fluid migration. The phase transition causes changes in pore structure, which in turn modifies porous infiltration parameters and fluid flow capacity. Meanwhile, alterations in phase interfaces affect key parameters like surface tension and wettability. Gas-liquid fluid migration influences heat and mass transfer, thus affecting phase equilibrium and dissociation rates. To bridge the gap in describing gas-liquid fluid migration during hydrate dissociation in experiments, this research innovatively integrated an unsteady-state gas displacement by water and a quantitative hydrate dissociation process, independently developed a multi-phase seepage experimental system suitable for hydrate dissociation and determined the relationship between seepage parameters and hydrate saturation under different porosity. The results are as follows: a) Core samples with higher initial porosity show a greater recovery rate of fluid flow capacity. b) The retarding effect of multi-phase fluid has a more significant impact on the migration of the wetting phase fluid (water) than that of the non-wetting phase fluid (methane). c) During hydrate dissociation, the evolution of absolute permeability shows an “S-shaped” pattern, and the evolution of relative permeability shows a “wiring-harness” pattern. In conclusion, the findings can provide a theoretical basis for preventing geological disasters and for geotechnical engineering design during hydrate production.

58 GEOSCIENCES↗
DOE OSTI2021

Tools for pressure core sub-coring and pore-scale micro-CT (computed tomography) scans

Abstract. The pore habits of gas hydrate in natural sediment matrices provide essential clues for understanding physical (mechanical, thermal, hydraulic, and electrical) properties of hydrate-bearing sediments, yet there are no tools that can directly visualize the pore habits of natural gas hydrate other than indirect interpretation based on core-scale or field-scale observations. A significant challenge is to obtain a mini-core from pressure cores retrieved from natural reservoirs for high-resolution micro-CT (computed tomography) scans while maintaining pressure and temperature conditions required for stability of gas hydrate during all operational steps including manipulation, cutting, transferring, sub-coring and CT scanning. We present a new set of tools for pore-scale micro-CT imaging of natural hydrate-bearing sediments while maintaining pressure and temperature control. The tests with laboratory-prepared cores and pressure cores successfully demonstrate the capability of this set of tools to subsample a mini-core from pressure cores, transfer the mini-core to an X-ray transparent core holder, and conduct micro-CT scans. Successfully obtained CT images prove the functionality of this set of tools.

Seol, Yongkoo↗
DOE OSTI2024

Pore-scale visualization of natural hydrate-bearing sediments

Accurate modeling of gas hydrate reservoir productivity and geomechanical risks associated with subsurface dissociation of natural gas hydrates (NGH) requires the determination of model parameters through physical testing on natural hydrate-bearing sediments (HBS). This involves investigating the hydro-mechanical behavior of undisturbed hydrate samples from nature under in situ conditions using pressure core characterization and analysis, which provides a unique opportunity for research. By employing state-of-the-art micro computed tomography imagery on cryogenically preserved, hydrate-bearing sediment samples, we can determine hydrate saturation as well as permeability with and without the presence of hydrates in the sediment. Furthermore, utilizing a machine learning based image segmentation technique, it is possible to extract pore space and grain information. Subsections of the entire image volume were used to determine anisotropic permeabilities using a finite-difference method Stokes solver (FDMSS). Additionally, permeability measurements on whole pressure and temperature preserved hydrate-bearing core were analyzed by utilizing the National Energy Technology Laboratory’s (NETL) Pressure Core Characterization and X-ray CT Visualization Tool (PCXT) to manipulate, cut, and analyze pressure preserved sediment. Permeabilities were measured under a broad range of vertical stress states to simulate expected pressure changes during production scenarios, and the results show that permeabilities derived from images are in agreement with those from traditional core derived experiments. The collected stress-dependent permeability, permeability anisotropy, and corresponding gas hydrate saturations provide valuable input into numerical simulations of reservoir productivity. These properties have been proven to be key parameters determining a long-term reservoir response under depressurization.

Liu, Mengwei [Oak Ridge Institute for Science and ↗
DOE OSTI2020

Timescales and Processes of Methane Hydrate Formation and Breakdown, With Application to Geologic Systems

Abstract Gas hydrate is an ice‐like form of water and low molecular weight gas stable at temperatures of roughly −10°C to 25°C and pressures of ~3 to 30 MPa in geologic systems. Natural gas hydrates sequester an estimated one sixth of Earth's methane and are found primarily in deepwater marine sediments on continental margins, but also in permafrost areas and under continental ice sheets. When gas hydrate is removed from its stability field, its breakdown has implications for the global carbon cycle, ocean chemistry, marine geohazards, and interactions between the geosphere and the ocean‐atmosphere system. Gas hydrate breakdown can also be artificially driven as a component of studies assessing the resource potential of these deposits. Furthermore, geologic processes and perturbations to the ocean‐atmosphere system (e.g., warming temperatures) can cause not only dissociation, but also more widespread dissolution of hydrate or even formation of new hydrate in reservoirs. Linkages between gas hydrate and disparate aspects of Earth's near‐surface physical, chemical, and biological systems render an assessment of the rates and processes affecting the persistence of gas hydrate an appropriate Centennial Grand Challenge. This paper reviews the thermodynamic controls on methane hydrate stability and then describes the relative importance of kinetic, mass transfer, and heat transfer processes in the formation and breakdown (dissociation and dissolution) of gas hydrate. Results from numerical modeling, laboratory, and some field studies are used to summarize the rates of hydrate formation and breakdown, followed by an extensive treatment of hydrate dynamics in marine and cryospheric gas hydrate systems.

58 GEOSCIENCES↗
DOE OSTI2022

Relative permeability of gas and water flow in hydrate-bearing porous media: A micro-scale study by lattice Boltzmann simulation

The water-gas relative permeability is an important parameter to characterize multiphase flow in sediments. To study the water-gas relative permeability of hydrate-bearing porous media, multiphase flow simulations were carried out at the pore scale using the lattice Boltzmann method. In this work, the effects of hydrate saturation and hydrate-growth habits on the water-gas relative permeability, which is scaled by the relative permeability considering the hydrate only, were evaluated in a two-dimensional porous medium. Results show that the increase of hydrate saturation causes the decrease of water-gas effective permeability as expected. However, the effect of hydrate saturation on the water-gas relative permeability is different from that of hydrate saturation on the water-gas effective permeability. The water-gas relative permeability increases with the increase of hydrate saturation in the pore-filling case. The water-gas relative permeability decreases with the increase of hydrate saturation in the grain-coating case. The wettability of solid phase has a different effect on the relative permeability of wetting phase and nonwetting phase. The Jamin effect (phase blocking) was observed and may exist in the production of gas from natural gas hydrate reservoirs. This seriously affects the multiphase flow characteristics. The changes of microscale fluid distribution effect the changes of water-gas relative permeability. The relationship between the water-gas relative permeability and the characterization parameters of microscale fluid distribution was analyzed.

58 GEOSCIENCES↗
DOE OSTI2020

Improved sampling technique to collect natural gas from hydrate-bearing pressure cores

High quality gas compositional data are an important factor in interpreting the genetic source of natural gas hosted in hydrate-bearing sediments and other subsurface systems. In order to accurately characterize the composition of gas samples degassed from hydrate-bearing pressure cores, one must use a reproducible sampling technique that minimizes artifacts of the sampling process. Herein, we review sediment core degassing techniques and compare data obtained from a commonly used degassing approach, which we term the standard quantitative degassing (SQD) technique, to our newly developed modified quantitative degassing (MQD) method designed to minimize atmospheric contamination and gas-water interactions. The SQD method allows sample gas to interact with water in a bubbling chamber, which we hypothesize could alter the gas composition following mixing with water or dissolved gases in the bubbling chamber. Whereas, the MQD method allows for the collection of sample gas prior to the bubbling chamber. To compare the SQD and MQD methods, we performed a side-by-side comparison of noble (He, Ne, Ar, Kr, and Xe), major (H 2 , N 2 , O 2 , and CO 2 ), and hydrocarbon (CH 4 , C 2 H 6 , C 3 H 8 , i-C 4 H 10 , C 4 H 10 , i-C 5 H 12 , C 5 H 12 ) gas concentrations and select isotopic compositions obtained using both sample collection techniques. Gas samples were collected from hydrate-bearing pressure cores recovered and maintained under hydrate stable conditions from the northern Gulf of Mexico during the UT-GOM 2 -1 Expedition. The MQD method displayed significantly lower concentrations of atmospheric gases, higher proportions of hydrocarbon gases, lower ratios of C 1 /C 2 + , and heavier stable carbon and hydrogen isotopes of methane than the SQD method. These results demonstrate that the MQD method reduced air contamination and minimized alteration of the hydrocarbon gases. Finally, we conclude this method may be important for future work that seeks to determine the composition of natural gas from pressure cores using quantitative degassing experiments, especially those seeking to measure major (e.g., N 2 ) and noble gases.

58 GEOSCIENCES↗
DOE OSTI2021

DOE Award No.: DE-FE0023919 Phase 4 Scientific/Technical Report

This is the Phase 4 Report for the ‘Deepwater Methane Hydrate Characterization and Scientific Assessment or Genesis of Methane Hydrates in the Gulf of Mexico (GOM2)’ research project (DOE Award No. DE-FE0023919). The report summarizes activities from October 1, 2019 to September 30, 2020. The project is led by the University of Texas at Austin (UT). The project objective is to gain insight into the nature, formation, occurrence and physical properties of methane hydrate-bearing sediments for the purpose of methane hydrate resource appraisal through the planning and execution of drilling, coring, logging, testing and analytical activities that assess the geologic occurrence, regional context, and characteristics of marine methane hydrate deposits in the Gulf of Mexico outer continental shelf (OCS). We published a dedicated American Association of Petroleum Geologists Bulletin volume describing initial results from the UT-GOM2-1 expedition in Sept. 2020. This is part 1 of a multi-volume commitment by AAPG to this project. We further confirmed that the natural gas in hydrate at GC-955 was formed by primary microbial processes (>76.1 %). The in-situ effective permeability hydrate-bearing sandy silts at the GC-955 reservoir ranges from 0.1 md (1.0×10-16 m2) to 2.4 md (2.4×10-15m2) in cores with 83% to 93% hydrate saturation. The intrinsic permeability (the single phase permeability) is estimated from reconstituted samples to be ~12 md (1.2×10-14 m2) to ~41 md (4.1×10-14 m2). We used observation and models to interpret that the core degradation that is found in pressure cores is due to dissociation of the methane hydrate in the outer circumference of the core and dissolution of that methane into the fresh pore water that the core is stored with. We are designing approaches to minimize this core loss in the future. We spent an enormous amount of effort to further improve the ability of the pressure coring tool (the PCTB) to pressure seal correctly. We completed upgrading the upper section of the PCTB to address poor pressure. We successful tested the modifications at Geotek’s test facility in Salt Lake City (Bench Test II). We completed a Land Test of the PCTB at the Schlumberger Cameron Test and Training Facility (CTTF). The tool did not seal in 6 out of 7 tests and we clearly demonstrated that cuttings were wedging in the ball valve assembly, keeping the ball valve from sealing. We reproduced the failure mechanism observed during the land test at Salt Lake City and confirmed the sensitivity of the ball valve assembly to grit. Geotek designed and tested 9 modifications to address this issue and the PCTB is now 100% successfully sealing in the presence of grit. Our science expedition is scheduled for spring 2022 and we are fully focused on preparing for this. UT and Ohio State completed a Shallow Hazard Assessment report for each proposed UT-GOM2-2 drilling location, pursuant to 30 CFR 250.214(f) and 250.244 (f). The Shallow Hazard Reports will accompany the UT-GOM2-2 Exploration Plan that is submitted to BOEM, and completes the geological and geophysical analysis for UT-GOM2-2 permitting efforts. We updated the UT-GOM2-2 Operations Plan (Version 1). We completed the UT-GOM2-2 Science and Sample Distribution Plan (Version 1). We evaluated the scope, budget, and schedule that would result from using a commercial vessel. We developed detailed drilling schedule, mud volume, and resource estimates. We developed a vessel specification document and a well plan, and sent these documents to prospective vessel contractors.

03 NATURAL GAS↗
DOE OSTI2020

Gas hydrate petroleum systems: What constitutes the “seal”?

The gas hydrate petroleum system (GHPS) approach, which has been used to characterize gas hydrates in nature, uses three distinct components: a methane source, a methane migration pathway, and a reservoir that not only contains gas hydrate, but also acts as a seal to prevent methane loss. Unlike GHPS, a traditional petroleum system (PS) approach further distinguishes between the reservoir, a unit with generally coarser sediment grains, and a separate overlying seal unit with generally finer sediment grains. Adopting this traditional PS distinction in the GHPS approach facilitates assessments of reservoir growth and production potential. The significance of the seal for the formation of a gas hydrate reservoir as well as for efficiency in methane extraction from the reservoir as an energy resource is evident in findings from recent offshore field expeditions, such as India’s second National Gas Hydrate Program expedition (NGHP-02). In regard to gas hydrate-bearing reservoir formations, the NGHP-02 gas chemistry data indicate a primarily microbial methane source. Fine-grained seal sediment in contact with coarser grained reservoir sediment can facilitate that microbial methane production. Logging-while-drilling and sediment core data also indicate that the overlying fine-grained seal sediment is less permeable than the underlying, highly gas hydrate-saturated reservoir sediment. The overlying seal’s capacity to act as a low-permeability boundary is important not only for preventing methane migration out of the reservoir over time, but also for preventing water invasion into the reservoir during methane extraction from the reservoir. Ultimately, the presence of an overlying, fine-grained, low-permeability “seal” influences how gas hydrate initially forms in a coarse-grained reservoir and dictates how efficiently methane can be extracted as an energy resource from the gas hydrate reservoir via depressurization.

Geochemistry & Geophysics↗
DOE OSTI2024

Characterization of the Structural–Stratigraphic and Reservoir Controls on the Occurrence of Gas Hydrates in the Eileen Gas Hydrate Trend, Alaska North Slope

One of the most studied permafrost-associated gas hydrate accumulations in Arctic Alaska is the Eileen Gas Hydrate Trend. This study provides a detailed re-examination of the Eileen Gas Hydrate Trend with a focus on the gas hydrate accumulation in the western part of the Prudhoe Bay Unit. This integrated analysis of downhole well log data and published geophysical data has provided new insight on structural, stratigraphic, and reservoir controls on the occurrence of gas hydrates in the Eileen Gas Hydrate Trend. This study revealed the relatively complex nature of the gas hydrate occurrences in the Eileen Gas Hydrate Trend, with gas hydrates present in a series of coarsening upward, laterally pervasive, mostly fine-grained sand beds exhibiting high gas hydrate saturations. Most of the gas hydrate-bearing reservoirs in the Eileen Gas Hydrate Trend are laterally segmented into distinct northwest- to southeast-trending fault blocks, occur in a combination of structural–stratigraphic traps, and are only partially hydrate filled with distinct down-dip water contacts. These findings suggest that the traditional parts of a petroleum system (i.e., reservoir, gas source, gas migration, and geologic timing of the system formation) also control the occurrence of gas hydrates in the Eileen Gas Hydrate Trend.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Evaluation of a Robust, In-Situ Surface Treatment for Pipeline Solids Deposition Mitigation in Flowing Systems

Abstract The formation/precipitation and deposition of pipeline solids, such as gas hydrates, asphaltenes, and waxes have long plagued production fields. Given the vast differences in chemistries of these solids, any current prevention or mitigation strategy, particularly for cases where multiple issues are a concern, is likely to involve an extensive assortment of undefined chemical additives that are both costly and add complexity to the system. Surface treatments (coatings), on the other hand, present a relatively new viable option for management strategies. A chemically and physically robust surface treatment with the ability to address deposition issues for multiple pipeline solids could not only decrease the operating expenditures for a field through material cost savings and obviation of downstream separation, but could also simplify produced fluids by eliminating additional chemicals from the mixture. The purpose of this study is to explore the feasibility of a particular surface treatment as part of a solids management strategy. This work utilizes an omniphobic surface treatment to probe its effects on gas hydrate, asphaltene, and wax deposition. Specifically, high pressure rocking cells are employed to study gas hydrate nucleation and deposition. A bench-scale flowloop filled with crude oil and heptane is used to quantify the deposition of crude oil and asphaltenes after a set time period. Lastly, a mechanical shear device measures the adhesion force of wax deposits on untreated/treated surfaces. The gas hydrate rocking cell tests demonstrate an increase in induction time and occasional elimination of hydrate nucleation with the surface treatment. Moreover, the same apparatus indicates that the critical shear to avoid hydrate deposition may be lowered in the presence of the surface treatment compared to untreated pristine carbon steel coupons. A custom-built asphaltene flowloop then establishes that this surface treatment is effective in dramatically reducing the deposition of the aliphatic components of a crude oil, with a moderate reduction in the asphaltene fraction. Finally, mechanical adhesion force measurements for solidified paraffin wax display trends in agreement with the asphaltene results. The surface treatment on both pristine and corroded surfaces is able to reduce the adhesion of wax deposits to values below a pristine, untreated surface.

03 NATURAL GAS↗
DOE OSTI2021

Surface Treatment Strategies for Mitigating Gas Hydrate & Asphaltene Formation, Growth, and Deposition in Flowloops

Abstract Numerous solids including gas hydrates, waxes, and asphaltenes have the potential to form in the production lines of gas and oil fields. This creates a highly non-ideal scenario as the accumulation of said species leads to flow assurance issues, especially with long-term processes like deposition. Since an ever-increasing amount of material is deposited in place at the pipe surface, production stoppage or active mitigation efforts become inevitable. The latter production issues result in increased safety risks and operational expenditures. Therefore, a cost-effective, passive deposition mitigation technology, such as a pipeline coating or surface treatment is especially appealing. The ability to address multiple pipeline flow assurance issues simultaneously without actively disrupting production would represent a dramatic step forward in this area. This study is part of a long-term ongoing effort that evaluates the performance and application of an omniphobic surface treatment for solids deposition prevention in industrially relevant systems. In particular, this specific work concentrates on the efficacy and robustness of the treatment under fully flowing conditions. The apparatuses utilized for this include two flowloops: a lab-scale, high-pressure flowloop for gas hydrate and surface treatment durability studies, and a bench-scale, atmospheric pressure loop for crude oil and asphaltene experiments. Film growth in high-pressure flowloop tests corroborated previous reports of delayed gas hydrate nucleation observed in rocking cells. Without the aid of the memory effect, treated oil-dominated experiments never experienced hydrate formation, spending upwards of a week in the hydrate stability zone (at the subcooled/fluid test conditions). Subsequent tests which utilized the memory effect then revealed that the hydrate formation rate reduced in the presence of the surface treatment compared to a bare stainless-steel surface. This testing was part of a larger set of trials conducted in the flowloop, which lasted about one year. The surface treatment durability under flowing conditions was evaluated during this time. Even after experiencing ∼4000 operating hours and 2 full pressure cycles, no evidence of delamination or damage was detected. Finally, as part of an extension to previous work, corroded surface asphaltene deposition experiments were performed in a bench-top flowloop. Treated experiments displayed an order of magnitude reduction in both total oil (all fractions of crude oil) and asphaltene fraction deposited.

03 NATURAL GAS↗
DOE OSTI2022

In situ inelastic neutron scattering of mixed CH 4 –CO 2 hydrates

An abundant source of CH 4 can be found in natural hydrate deposits. Recent demonstration of CH 4 recovery from hydrates via CO 2 exchange has revealed the potential as a fuel source that also provides a medium for carbon sequestration. It is vital to understand the structural and dynamic impacts of guest variation in CH 4 , CO 2 , and mixed hydrates and link the results to the stability of various deposits in nature, harvesting methane, and sequestering CO 2 . Molecular vibrations are examined in CH 4 , CO 2 , and mixed CH 4 -CO 2 hydrates at 5 and 190 K and Xe hydrates for comparison. Inelastic neutron scattering (INS) is an ideal spectroscopy technique to observe the dynamic modes in the hydrate structure and enclathrated CH 4 , as it is extremely sensitive to 1 H. The presence of CO 2 in hydrates tightens the lattice. It introduces more active librational modes to the host lattice, while hindering the motion of CH 4 in mixed CH 4 -CO 2 hydrate at 5 K. At 190 K, a large broadening of the CH 4 librational modes indicates disorder in the structure leading to dissociation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Extending TOUGH + HYDRATE with a parallel particle transport simulator: numerical investigation of sand production during gas production from hydrate deposits

A new parallel code for simulating particle transport in porous media is integrated with the TOUGH + HYDRATE simulator to investigate sand production associated with gas production from unconsolidated gas hydrate-bearing sediments (HBS). Here, the parallel coupled simulator is named THMPT and uses the integral finite difference method to describe the Darcian and non-Darcian flow of fluids and heat transport, the finite element method to describe the associated geomechanical changes, and the discrete element method to track the trajectory of individual sand particles within the HBS. The THMPT simulator is written in Fortran, incorporates multiple optimized algorithms, and can comprehensively address the coupled flow, thermal, chemical, geomechanical, and particle transport processes that characterize the system behaviors during gas production from HBS. The simulator can capture all processes involved in sand particle transport in porous media, including sand detachment, collision, clogging (i.e., bridging), and migration. A benchmark case study of sand production in the course of depressurization-induced gas production from a representative HBS reveals various distinct microscopic particle migration mechanisms and the adverse impact of sand particle detachment, transport, and clogging. The numerical investigation also examines the effect of bottomhole pressure on mitigating sand production. The simulation results indicate that sand clogging near the wellbore significantly reduces permeability, decreasing gas production by at least 50%. Lastly, the efficiency of gravel packing in mitigating sand production is numerically evaluated, revealing that the structure of the porous media appears to profoundly influence the macroscopic motion behavior of sand particles and sand clogging characteristics.

discrete element method↗