Search NASA⌕ Search

SEARCH · Search NASA

Results for “near net shape”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Methods of forming near-net shape structures from non-stoichiometric oxides

A method of forming a near-net shape structure comprises forming a structure comprising non-stoichiometric metal oxide comprising at least one metal and less than a stoichiometric amount of oxygen, and electrochemically reducing the non-stoichiometric metal oxide in an electrochemical cell to form a structure having a near-net shape and comprising the at least one metal having less than about 1,500 ppm oxygen. Related methods of forming a non-stoichiometric metal oxide by sintering, annealing, or additive manufacturing, and forming a near-net shape structure from the non-stoichiometric metal oxide, as well as related electrochemical cells are also disclosed.

Tripathy, Prabhat K.↗
DOE OSTI2024

Near-Net-Shape Hot Isostatic Press Manufacturing Modality for sCO2 CSP Capital Cost Reduction

Through this DOE funded 3.5-year research project, feasibility of fabricating supercritical carbon dioxide (sCO2) turbine components by powder metallurgy (PM) based near-net-shape (NNS) hot isostatic pressing (HIP) was demonstrated in a turbine nozzle ring, a turbine casing with Haynes 282 powder, and a bimetallic pipe with Haynes 282 and SS415 powder. As-HIP microstructure of various powders and HIP processing conditions was studied to downselect a condition for the prototype components. Tensile strength and low cycle fatigue (LCF) capability of PM HIP 282 was found to be superior to cast 282, despite a debit in creep stress capability that could be mitigated by component design modification. Near-Net-shape with minimal post machining was achieved by modeling the non-uniform shrinkage during HIP cycle and designing the HIP tooling to meet dimensional targets. The prototypes of turbine nozzle ring and bimetallic pipe were successful in achieving overall dimension, microstructure, and properties, despite dimensional tolerance affected by chemical milling rate. The prototype of a 1700lbs turbine casing was partially successful in achieving dimension, microstructure in as-HIP state, and providing consistent mechanical properties, however, cracking issue during post heat treatment required further investigation. The estimated manufacturing cost using NNS HIP was a ~50% reduction compared to forging with extensive machining, which translated into ~$100/kWe CAPEX cost reduction for concentrated solar power (CSP) power block.

14 SOLAR ENERGY↗
DOE OSTI2023

Near-Net-Shape HIP Manufacturing for sCO2 Turbomachinery Cost Reduction

sCO2 turbomachinery that operates above 650°C requires the use of γ' strengthened Ni-based superalloys, leading to high cost and barrier of market adoption. Near-net-shape (NNS) HIP manufacturing with 282® alloy powder is being developed for sCO2 turbine components, with a significant estimated cost reduction. Tensile, creep, low cycle fatigue properties of argon gas atomized and plasma atomized powders were evaluated and compared to sand cast HAYNES® 282®. While tensile strength and fatigue life outperformed sand cast material, a 10~25% debit in the creep stress capability was observed due to the fine grain size and presence of prior particle boundaries (PPBs). Finite element model calibrated by powder rheological properties accurately predicted the nonuniform shrinkage during HIP, providing HIP tooling design to achieve the target dimension. A 20 lbs. turbine nozzle ring was successfully demonstrated within 0.01 inch dimensional tolerance at the vanes. A 1700lbs. turbine casing with complex internal struts and manifolds was also demonstrated being close to the target dimension.

14 SOLAR ENERGY↗
DOE OSTI2024

Near-net shaping of high-density, complex, spatially-tailored ceramics for extreme environments

The purpose of this subcontract is for LLNL to collaborate with the Subcontractor (UCSB) in the areas of binder jet additive manufacturing (BJAM), hot pressing (HP), finite element modeling (FEM), and multi-material sintering studies. LLNL wants to further develop its hot pressing, AM, and modeling capabilities through LLNL’s Early Career Faculty Program. This work will focus on developing a method to hot press complex-shaped ceramic parts through the co-deposition of a structural/functional ceramic and sacrificial mold material in one assembly via multi-material binder jet printing. The method aims to produce dense, near-net shaped parts with applications relevant to a wide variety of fields including aerospace, defense, and energy.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Hydrogen-based ore-to-part manufacturing of near-net-shape stainless steel

Decarbonizing iron and steelmaking, combined with global disruptions to raw material supply chains, necessitates novel approaches to iron and steel production. In this work, we demonstrate a direct ore-to-part manufacturing route using a mixture of ore-derived oxide powders of Fe 2 O 3 , Cr 2 O 3 , NiO, and MoO 3 as feedstock for additive manufacturing, combined with sintering under H 2 to produce a near-net-shape austenitic stainless-steel. Complete reduction of all constituent oxides, including MoO 3 and Cr 2 O 3 , is achieved in-situ at 1300 °C, resulting in dense, crack-free bulk alloy. The fabricated part retains geometric fidelity while undergoing substantial volumetric shrinkage inherent to redox and sintering. Thermodynamic calculations elucidate the co-reduction mechanisms and alloying pathways that enable complete metallization. This work is the first demonstration of net-shaping metal parts directly from ore derived oxides, and this ore-to-part approach can minimize the emissions and lead time for manufacturing associated with downstream processing such as rolling, forging, and machining.

Yang, Mingzhang [Univ. of Waterloo, ON (Canada); F↗
DOE OSTI2024

Reduction kinetics of hematite powder using argon/hydrogen plasma with prospects for near net shaping of sustainable iron

Direct reduction of iron ore using hydrogen plasma is being explored as a potential solution to decarbonize the iron and steel sector. The current state-of-the-art demonstrated reduction of hematite pellets via hydrogen plasma using Ar + 10% H 2 but had slow reduction kinetics, requiring 30 minutes of plasma exposure for complete reduction. Here we show that using hematite in a powder form, easily obtainable from beneficiated ore, results in 10× faster kinetics using plasma generated from Ar + 2% H 2 shielding gas compared to the current state-of-the art. Additionally, the increased kinetics using powders and a dilute hydrogen concentration can enable the use of advanced manufacturing techniques like blown powder directed energy deposition using a plasma tungsten arc welding torch to manufacture near net shape components directly from the ore concentrates. This ore to part approach will also reduce the emissions associated with downstream processes like rolling, forging, and machining, thereby further aiding in the sectorial decarbonization efforts.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Near Net Shape Workshop Report

In 2021, President Biden issued Executive Order (EO) 14017, spurring the federal government to build more secure and diverse U.S. supply chains, including energy supply chains, to ensure economic prosperity and national security (White House 2021). In response to EO 14017, the U.S. Department of Energy (DOE) published America’s Strategy to Secure the Supply Chain for a Robust Clean Energy Transition (Igogo 2022) to outline the challenges and opportunities facing the energy supply chain along with key strategies to secure America’s position as a clean energy superpower in the years and decades to come. The expansion of domestic manufacturing capabilities is identified as one of the common risks and vulnerabilities for which DOE should develop comprehensive strategies to secure supply chains for the clean energy transition. The report states that “examples of manufacturing capabilities of concern include … large iron and steel castings for wind turbines, hydropower turbines, and nuclear reactor components.”

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Electroslag additive manufacturing: A pathway for high throughput near net shape production

Electroslag Additive Manufacturing (ESAM), a new high-throughput additive manufacturing (AM) method that combines Electroslag Strip Cladding (ESC) and wire arc AM (WAAM) is introduced. This combination enables the high deposition rate of ESC (more than 20 kg/h with a 60 mm strip electrode) to benefit from the precise geometric control of WAAM. As a precursor to ESAM, the ESC process is investigated in an AM context independently by evaluating both direct and staggered bead-stacking strategies and analyzing the microstructural and mechanical properties of each. This is followed by an ESAM demonstration producing an annular geometry by pairing ESC with gas tungsten arc welding (GTAW), wherein GTAW is utilized to construct annular walls that are subsequently infilled via ESC. The microstructure and mechanical properties of ESC-only AM are compared with that of the ESAM method and it is shown that printed integral retaining walls do not impact the resulting mechanical properties of ESAM. Furthermore, results indicate that ESAM-produced Alloy 625 parts exhibit tensile properties on par with cast counterparts, supporting the method’s scalability to components exceeding one metric ton, and possibly making ESAM a viable future manufacturing approach for competitive production of large-scale components currently manufactured by casting and forging.

Additive manufacturing↗
DOE OSTI2025

Ink-based laser powder bed fusion of barium titanate

Barium titanate (BTO) is a lead-free functional ceramic that is widely used in sensors, transducers, and actuators. The increasing demand for complex geometries and quick design iterations motivates the use of additive manufacturing techniques. Laser powder bed fusion (L-PBF) additive manufacturing technique enables the net-shape or near-net-shape fabrication of metals and alloys. Ceramic L-PBF remains challenging due to their high melting temperature. Here, to address this challenge, a nanoparticle ink feedstock was incorporated into the L-PBF process to allow low power melting of BTO. Key print parameters (i.e. laser power, scanning speed, and hatching spacing) were optimized to fabricate millimeter-scale BTO parts. The printed BTO samples possessed an inhomogeneous equiaxed-columnar-cellular microstructure. Semiconducting current-voltage behavior was observed in as-printed samples, which was attributed to the creation of oxygen vacancies. The piezoelectric d 33 coefficient was measured to be 4.6 pC/N.

Dielectrics↗
DOE OSTI2025

Extending wire-arc directed energy deposition using non-gravity aligned (NGA) torch methods

For standard Additive Manufacturing (AM) processes, traditional path planning typically relies on a 2.5-dimensional approach. In wire-arc directed energy deposition (DED), commonly referred to as wire-arc additive manufacturing (WAAM), this 2.5D approach inherently limits final near net shape due to the stair-step effect and restricts the maximum overhang angle achievable without part degradation. To achieve better near net shape and part quality, a 3D planning approach that modulates the tool tip position and angle without process changes is demonstrated in components containing up to 105° of unsupported overhang. The experimental methods are validated with half and fully enclosed cylinder sections containing 90° of overhang. The non-gravity aligned methods are then applied to a commercial WAAM system for a composite tool mold demonstrator part. As a result, the methods developed in this paper enable expansion of WAAM system capabilities to parts containing large overhangs without compromising the net shape or material structure of the resulting parts and without the need for a part positioner.

Additive manufacturing↗
DOE OSTI2024

Report on use of Inoculants in Missile Application Alloys

This report documents the status of current inoculant research relevant to missile application alloys and MTCR control language. The information is intended to provide data on current inoculants for us determining the current state of development and identifying potential research directions. Although there has been significant scientific research into the development and synthesis of inoculants, their current availability is limited is traditional powder inoculants employed during casting processes. However, research continues the development of complex oxides, ribbon materials, high entropy alloys, and other inoculant product forms, including the use of inoculants in the melt pools produced during additive manufacturing. Research to date has focused primarily on aluminum and steel alloys with emphasis on refining grain structures and evolving equiaxed morphologies while increasing strength and castability. The primary inoculants in steel and cast irons include TiN, SiC, FeSi75, and Ce which have increased strength properties. Chief inoculants for Al alloys often include TiC, SiC, Al3Sc(x) and TiB2 to aid in precipitation and refinement. Ti and Ni alloys have fewer research activities involving inoculants, although TiN, TiB, ZrN and LaB6 (for Ti alloys) and WC, Co3FeNb2, and CrFeNb (for Ni alloys) have been used. Sic, Al2O3, Mg and Ti are key inoculants for Mg alloys. Multiple cast alloys from each of the material classes demonstrated increased strength and performance properties using inoculants, with several approaching requirements applicable to missile service environments. The continued evolution of advanced manufacturing capabilities is making it easier to produce high temperature near net shape structural materials using inoculant powders. These shapes may include the geometric shapes addressed within the MTCR (tubes and limited wall thicknesses). The use of inoculants may enable further development of high temperature alloys into near net shapes traditionally produced via casting processes due to limited ductility. This may decrease material and manufacturing costs. In addition, inoculation provides controlled kinetics and achievable chemical segregation that enables potential for far-from equilibrium thermodynamic microstructures and chemistries that could provide new metastable alloy states and subsequent properties to address co-design engineering constraints, including needs for increased strength and ductility. It is recommended that specific material combinations within these alloy classes be carefully watched as the materials evolve, with controls aimed at those having material properties above current MTCR levels. This specifically includes the use of refractory inoculants in alloys, and the application of inoculants in high strength and high temperature alloys via additive manufacturing processes, with care to link capabilities to product forms similar to the current requirements on tube geometries and material feed stocks. The continued development of nanoparticle inoculants will increase strength and ductility of high strength castings and additive manufactured metallic components. For example, adding inoculants into the casting of maraging steels and other precipitation strengthened alloys may drastically elevate mechanical properties above the control limit of current regulations.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Development of large-scale, 3D Printed high temperature ceramic material

Through this collaborative effort, a new 3D printing platform for ceramics called laser-induced slip casting (LIS) was explored and developed for improving the processing and manufacture of silicon carbide (SiC), a high temperature ceramic material. This method prints layers of ceramic slips/slurries with subsequent selective-laser heating to dry each layer to build a 3D structure. The completed and dried part is then sintered. This manufacturing process is inherently lower cost than alternative ceramic printing methods such as binder jet technology or stereolithography when it comes to the feedstock material but is more expensive than robocasting or direct ink writing. However, it has the potential to make more controlled parts with less defects compared to robocasting. The largest cost is the heating source for the printer. With this technique, there is potential to make large ceramic parts in a near-net shape. Further, there is no known commercial manufacturing of 3D printed ceramics that creates a large range of different high-density ceramics at large scale. The goals and outcomes for the development of the new printing technology were: 1) assessing the technology with alumina by characterizing coupons, 2) printing and sintering of silicon carbide (SiC), and 3) characterization and properties testing of materials printed and a scale-up of SiC part(s). Through this collaborative project, it was sought to provide the best solution to achieving highly dense and near-net shaped ceramic parts at large scale and reduced cost. The goal was to produce high density sintered materials for applications in defense, energy generating systems, armor, and wear parts using 3D printing methods. Variables including powder particle sizes, dispersant molecular weights (MWs), binders, printing parameters, and post processing were explored as well as the characterization of the physical properties (add specifics here).

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ultra-high temperature carbide foams and methods of fabricating the same

Ultra-high temperature carbide (UHTC) foams and methods of fabricating and using the same are provided. The UHTC foams are produced in a three-step process, including UHTC slurry preparation, freeze-drying, and spark plasma sintering (SPS). The fabrication methods allow for the production of any kind of single- or multi-component UHTC foam, while also providing flexibility in the shape and size of the UHTC foams to produce near-net-shape components.

Agarwal, Arvind↗
DOE OSTI2025

A visco-plastic constitutive model for accurate densification and shape predictions in powder metallurgy hot isostatic pressing

Powder metallurgy hot isostatic pressing (PM-HIP) is an advanced manufacturing process that produces near net shape parts with high material utilization and uniform microstructures. Despite being used frequently to produce small-scale components, the application of PM-HIP to large-scale components is limited due to inadequate understanding of its complex mechanisms that cause unpredictable post-HIP shape distortions. A computational model can provide necessary information about the intermediate and final stages of the HIP process that can help understand it better and make accurate predictions. Generally, two types of computational models are employed for PM-HIP of metal powders, namely, plastic and visco-plastic models. Between these, the plastic model is preferred due to its cheaper calibration approach requiring less experimental data. However, the plastic model sometimes produces incorrect predictions when slight variations of the HIP conditions are encountered in practical situations. Therefore, this work presents a visco-plastic model that addresses these limitations of the plastic model. A novel modified calibration approach is employed for the visco-plastic model that utilizes less experimental data than existing approaches. With the new approach, the data requirement is same for both plastic and visco-plastic models. This also enables a quantitative comparison of plastic and visco-plastic models, which have been only qualitatively compared in the past. When calibrated with the same experimental data, both the models are found to produce similar results. In conclusion, the calibrated visco-plastic model is applied to several complex geometries, and the predictions are found to be in good agreement with experimental observations.

Hot isostatic pressing↗
DOE OSTI2026

A fast and robust computational modeling approach for density and shape predictions in powder metallurgy hot isostatic pressing

Powder metallurgy hot isostatic pressing (PM-HIP) is an advanced manufacturing process that produces near-net-shape parts with high material utilization and uniform microstructures. PM-HIP is frequently used for producing small-scale parts with complicated geometries and is potentially economical for producing large-scale parts. However, excessive post-HIP shape distortions can reduce its effectiveness and economic advantage, especially for larger parts. A PM-HIP computational model can predict and help mitigate these distortions. However, due to complex deformation mechanisms and thermo-mechanical coupling present in PM-HIP processes, these non-linear computational models sometimes become numerically unstable. The numerical instabilities in these models can lead to very slow convergence or no convergence at all, which often translates to slow and unreliable models. These limitations are more pronounced in large models with complicated geometries. Hence, in this work, an alternative modeling approach is presented that improves numerical stability and computational performance. The presented approach achieves these improvements through approximating the fully coupled thermo-mechanical PM-HIP model as a decoupled model and adding inertial damping to the model’s mechanical part. In conclusion, a comparison with the fully coupled model indicated a slight dip in prediction accuracy (<5% error) but significant improvements in numerical stability (>20 times larger time step size) and computational performance (5-10 times speed-up with less computational resource usage) when using the presented approach.

Hot isostatic pressing↗
DOE OSTI2023

An Initial Evaluation of the Elevated-Temperature Cyclic Properties of Optimized 316H Stainless Steel Fabricated by Powder Metallurgy Hot Isostatic Pressing

Powder metallurgy hot isostatic pressing (PM-HIP) is a mature advanced manufacturing technology, which can consolidate metallic powder under high temperature and pressure to generate near-net shape components. This process can lower production costs and reduce component lead times for nuclear reactor construction and can be readily deployed in the near term for microreactor components because of their smaller size. The purpose of this work is to continue the evaluation of elevated-temperature cyclic material properties for PM-HIP 316H stainless steel. Prior scoping results have shown that the commercially procured PM-HIP stainless-steel materials have reduced creep-fatigue performance compared to wrought 316 stainless steels. To better understand how PM-HIP processed material properties compare to traditional manufacturing methods, additional billets of PM-HIP 316H stainless steel were procured and tested. This testing is necessary to understand how elevated-temperature properties are influenced by the PM-HIP process and what data are needed for incorporating PM HIP 316H into the American Society of Mechanical Engineers Boiler Pressure Vessel Code, Section III, Division 5 for high temperature reactor construction. Specifically, an additional PM-HIP 316H stainless steel billet with lower oxygen and nitrogen concentrations was fabricated by the Nuclear Advanced Manufacturing Research Centre of the United Kingdom and tested to understand if elevated-temperature cyclic properties can be improved. The creep-fatigue resistance of the material from this new billet did not show appreciable improvement compared to prior testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Assessment of Benefits of Solid-State Advanced Manufacturing Processes for Nuclear Energy Products

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. This overall project provides the U.S. Department of Energy a critical feasibility study comparison of three solid-state processes to other AM processes, thereby providing the feasibility of the solid-state processes examined to manufacture 316H SS and ODS steel components: • Fused-filament fabrication (FFF): This work provides an initial evaluation of the impact of powder morphology and sizes on the FFF process, and the feasibility and adaptability for different material systems, to use FFF for ODS steels and 316 SS. • Shear-assisted processing and extrusion (ShAPE): Specifically for this portion of the project on ShAPE tube forming, the objectives will be to determine the feasibility to direct tube forming of high tensile strength steel tubing, specifically for ODS steel to determine the effect of the patented extrusion process on the dispersoids of the ODS material. Additionally, as often ODS powders are mechanically alloyed and therefore more platelike or angular, this feasibility was to explore the impact on the optimization process and initial feasibility of direct tube forming. • Cold spray and friction stir additive manufacturing as a stretch goal: Bulk and near net shape manufacturing processes for high-temperature, high-strength alloys are needed. Additionally, cold spray techniques can be applied in-situ at the operational level for repair and can provide multiple benefits to the nuclear industry. These tasks aim to provide information to show benefits of cold spray during the full life cycle, namely research and development, product manufacturing, and repair to mention a few key points.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Thermal Spray toolpath development for a capped cylinder (“cake pan”) substrate

A near net shape coating is desired to be applied to the outer surface of a capped cylinder (“cake pan”) type substrate using thermal spray technology. A capped cylinder geometry is more complex than simple coupon-level substrate substrates (e.g., flat panels, cylinders) and thus requires a more complex toolpath to deposit a uniform coating. This report documents a practical theoretical approach to calculating relative torch-to-substrate speeds for coating the cylindrical, corner, and cap region of a rotating capped cylinder based on fundamental thermal spray toolpath principles. A preliminary experimental test deposited a thermal spray coating onto a mock substrate using toolpath speeds calculated by the theoretical approach proposed. The mock substrate was metallographically inspected to assess coating uniformity across the cylindrical, corner, and cap region. Inspection of the mock substrate revealed qualitatively uniform coating microstructure and thickness where theoretically predicted, demonstrating the viability of the proposed toolpath method and associated calculations. Pathways forward to optimizing coating uniformity at the cap center are proposed as near term suggested future work.

42 ENGINEERING↗