Search NASA⌕ Search

SEARCH · Search NASA

Results for “nickel based”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Application of Gold Electrodes for the Study of Nickel Based Homogeneous Catalysts for Hydrogen Oxidation

Gold and glassy carbon working electrode materials are compared as suitable substrates for the hydrogen oxidation reaction with Ni(PCy2Nt-Bu2)2(BF4)2 used as a catalyst. Voltammetric responses showing electrocatalytic hydrogen oxidation mediated by the homogeneous electrocatalyst Ni(PCy2Nt-Bu2)2(BF4)2 are identical at glassy carbon and gold electrodes, which shows that gold electrode can be used for hydrogen oxidation reaction. This work is supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the US Department of Energy, Office of Science, Office of Basic Energy Sciences under FWP 56073.

"glassy carbon"↗

Unveiling the Stabilities of Nickel–Based Layered Oxide Cathodes at an Identical Degree of Delithiation in Lithium–Based Batteries

Bulk, surface, and interfacial instabilities that impact the cycle and thermal performances are the major challenges with high-energy-density LiNi 1–x–y Mn x Co y O 2 (NMC) cathodes with high nickel contents. It is generally believed that the instabilities and performance losses become exponentially aggravated as the nickel content increases. Disparate from this prevailing belief, it is herein demonstrated that NMC cathodes with higher Ni contents may imply better overall stability than “lower-Ni” cathodes under an identical degree of delithiation (charging) conditions. With two representative cathodes, LiNi 0.8 Mn 0.1 Co 0.1 O 2 and LiNiO 2 , a systematic investigation into their stabilities with control of the degree of delithiation is presented. Electrochemical tests indicate that LiNiO 2 displays better cyclability than LiNi 0.8 Mn 0.1 Co 0.1 O 2 at the same delithiation state. Comprehensive structural and interphase investigations unveil that the inferior cyclability of LiNi 0.8 Mn 0.1 Co 0.1 O 2 predominantly results from aggravated parasitic reactions, and the interphase stability may be more critical than lattice stability in dictating cyclability. Also, LiNiO 2 delivers similar or better thermal behavior than LiNi 0.8 Mn 0.1 Co 0.1 O 2 . Finally, the findings demonstrate a strong correlation of the stability of NMC cathodes to the degree of delithiation state rather than the Ni content itself, highlighting the importance of reassessing the true implications of Ni content and structural and interphasial tuning on the stabilities of NMC cathodes.

25 ENERGY STORAGE↗

Layered nickel based superconductors

We review the properties of Ni-based superconductors which contain Ni{sub 2}X{sub 2} (X=As, P, Bi, Si, Ge, B) planes, a common structural element to the recently discovered FeAs superconductors. We also compare the properties ofthe Ni-and Fe-based systems from a perspective ofelectronic structure as well as structure-property relations.

36 MATERIALS SCIENCE↗

Atomic Diffusion, Segregation, and Grain Boundary Migration in Nickel-Based Alloys from Molecular Dynamics Simulations

Grain boundary diffusion and metal mobility in alloys control material performance in many applications and yet remain poorly understood at a mechanistic level. With advances in accessible time and length scales for computational molecular simulations, and recent force field developments, we now possess tools to help unravel those mechanisms. Using large-scale molecular dynamics simulations, here we examined vacancy-mediated diffusion processes in Ni-5Cr alloy with low and high-energy grain boundaries. We show that atomic diffusion inside the grain boundary plane is about four times higher than bulk diffusion, at any temperature, and exhibits a typical Arrhenius behavior with a very small energy barrier (0~.8 eV for Cr and 0.7 eV for Ni within 1300-1600 K). Additionally, the fastest diffusing species inverts; Cr diffusion was faster than Ni in the bulk but slower in the grain boundaries. This is attributed to the creation of high cohesive energy clusters of Cr at the grain boundary. Grain boundary migration was also observed to be temperature dependent and appears to be two times higher in the 5% Cr alloy than in pure Ni, highlighting the important role of the alloying element on grain boundary motion.

Simonnin, Pauline GN↗

Effects of prior deformation and annealing process on microstructure and annealing twin density in a nickel based alloy

The nickel based alloys with different Σ3 boundary density were achieved by cold-rolling and subsequent annealing treatment. Electron backscattered diffraction analysis showed that the grain size distribution changed with the processing parameters, and the discontinuous Σ3 boundary became continuous with the increase of prior deformation level. Furthermore, the Σ3 boundary density was found to be manipulated by both grain size distribution and Σ3 boundary density per grain which showed an increasing trend with prior deformation level and annealing temperature. - Highlights: • The prior deformation amount influenced the morphology of Σ3 boundary. • The grain size was not the only factor influencing Σ3 boundary density. • The fact that grain size distribution had an important effect on Σ3 boundary density was confirmed. • The nature of grain size distribution on Σ3 boundary density was revealed. • There was a great deviation in Σ3 boundary density between experimental results and predictions.

36 MATERIALS SCIENCE↗

ON THE INFLUENCE OF COLD WORK ON RESISTIVITY VARIATIONS WITH THERMAL EXPOSURE IN IN-718 NICKEL-BASE SUPERALLOY

In nickel-base superalloys, irreversible electrical conductivity changes occur above a transition temperature where thermally-activated microstructural evolution initiates. The electrical conductivity first decreases above about 450 deg. C then increases above 600 deg. C. However, the presence of plastic deformation results in accelerated microstructure evolution at an earlier transition temperature. It was recently suggested that this well-known phenomenon might explain the notable conductivity difference between the peened near-surface part and the intact part at sufficiently large depth in surface-treated specimens. The influence of cold work on the electrical conductivity change with thermal exposure offers a probable answer to one of the main remaining questions in eddy current residual stress assessment, namely unusually fast and occasionally even non-monotonic decay of the apparent eddy current conductivity (AECC) change that was observed at temperatures as low as 400 deg. C. To validate this explanation, the present study investigates the influence of cold work on low-frequency Alternating Current Potential Drop (ACPD) resistivity variations with thermal exposure. In-situ resistivity monitoring was conducted throughout various heating cycles using the ACPD technique. IN-718 nickel-base superalloy specimens with different levels of cold work were exposed to gradually increasing peak temperatures from 400 deg. C to 800 deg. C. The results indicate that the initial irreversible rise in resistivity is approximately one order of magnitude higher and occurs at about 50 deg. C lower temperature in cold-worked samples of 30% plastic strain than in the intact material.

36 MATERIALS SCIENCE↗

Microstructural, mechanical and weldability assessments of the dissimilar welds between γ′- and γ″-strengthened nickel-base superalloys

Dissimilar welding of γ′- and γ″-strengthened nickel-base superalloys has been investigated to identify the relationship between the microstructure of the welds and the resultant mechanical and weldability characteristics. γ′-Strengthened nickel-base Alloy 500 and γ″-strengthened nickel-base Alloy 718 were used for dissimilar welding. Gas tungsten arc welding operations were utilized for performing the autogenous dissimilar welding. Alloy 500 and Alloy 718 base metals showed various types of phases, carbides, intermetallics and eutectics in their microstructure. The results for Alloy 500 weld metal showed severe segregation of titanium to the interdendritic regions. The Alloy 718 weld metal compositional analysis confirmed the substantial role of Nb in the formation of low-melting eutectic-type morphologies which can reduce the weldability. The microstructure of dissimilar weld metal with dilution level of 65% wt.% displayed semi-developed dendritic structure. The less segregation and less formation of low-melting eutectic structures caused to less susceptibility of the dissimilar weld metal to the solidification cracking. This result was confirmed by analytic modeling achievements. Dissolution of γ″-Ni{sub 3}Nb precipitations took place in the Alloy 718 heat-affected zone leading to sharp decline of the microhardness in this region. Remelted and resolidified regions were observed in the partially-melted zone of Alloy 500 and Alloy 718. Nevertheless, no solidification and liquation cracking happened in the dissimilar welds. Finally, this was concluded that dissimilar welding of γ′- and γ″-strengthened nickel-base superalloys can successfully be performed. - Highlights: • Dissimilar welding of γ′- and γ″-strengthened nickel-base superalloys is studied. • Microstructural, mechanical and weldability aspects of the welds are assessed. • Microstructure of welds, bases and heat-affected zones is characterized in detail. • The type, morphology and distribution of the phases are thoroughly investigated. • Dissimilar welding is successfully performed without occurrence of any hot cracks.

36 MATERIALS SCIENCE↗

Influence of composition on microstructural parameters of single crystal nickel-base superalloys

Fourteen nickel-base superalloy single crystals containing a range of chromium (Cr), cobalt (Co), molybdenum (Mo), and rhenium (Re) levels, and fixed amounts of aluminum (Al) and tantalum (Ta), were examined to determine the effect of bulk composition on basic microstructural parameters, including {gamma} Prime solvus, {gamma} Prime volume fraction, topologically close-packed (TCP) phases, {gamma} and {gamma} Prime phase chemistries, and {gamma}-{gamma} Prime lattice mismatch. Regression models describing the influence of bulk alloy composition on each of the microstructural parameters were developed and compared to predictions by a commercially-available software tool that used computational thermodynamics. Co produced the largest change in {gamma} Prime solvus over the wide compositional range explored and Mo produced the biggest effect on the {gamma} lattice parameter over its range, although Re had a very potent influence on all microstructural parameters investigated. Changing the Cr, Co, Mo, and Re contents in the bulk alloy had an impact on their concentrations in the {gamma} matrix and to a smaller extent in the {gamma} Prime phase. The software tool under-predicted {gamma} Prime solvus temperatures and {gamma} Prime volume fractions, and over-predicted TCP phase volume fractions at 982 Degree-Sign C. However, the statistical regression models provided excellent estimations of the microstructural parameters and demonstrated the usefulness of such formulas. - Highlights: Black-Right-Pointing-Pointer Effects of Cr, Co, Mo, and Re on microstructure in new low density superalloys Black-Right-Pointing-Pointer Co produced a large change in {gamma} Prime solvus; Mo had a large effect on lattice mismatch. Black-Right-Pointing-Pointer Re exhibited very potent influence on all microstructural parameters was investigated. Black-Right-Pointing-Pointer {gamma} and {gamma} Prime phase chemistries both varied with temperature and alloy composition. Black-Right-Pointing-Pointer Computational thermodynamic modeling tool did not accurately predict microstructure.

36 MATERIALS SCIENCE↗