Search NASA⌕ Search

SEARCH · Search NASA

Results for “normal displacement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Study on the Correlation Between Dynamical Behavior and Friction/Wear Mechanism Under the Effect of Grooves

In this work, the interfacial friction and wear and vibration characteristics are studied by sliding a chromium bearing steel ball (AISI 52100) over both multi-grooved and single-grooved forged steel disks (20CrMnMo) at low and high rotating speeds in order to reveal the effect mechanism of groove-textured surface on tribological behaviors. The results show that the grooves modify the contact state of the ball and the disk at the contact interface. This consequently causes variations in the normal displacement, normal force, and friction force signals. The changes in these three signals become more pronounced with increasing groove width at a low speed. The collision behavior between the ball and the groove increase the amplitude of vibration acceleration at a high speed. The test results suggest that grooves with appropriate widths could trap wear debris on the ball surface while avoiding a strong collision between the disk and the ball, resulting in an improvement in the wear states.

36 MATERIALS SCIENCE↗

Correlation functions for the fractional generalized Langevin equation in the presence of internal and external noise

We study generalized fractional Langevin equations in the presence of a harmonic potential. General expressions for the mean velocity and particle displacement, the mean squared displacement, position and velocity correlation functions, as well as normalized displacement correlation function are derived. We report exact results for the cases of internal and external friction, that is, when the driving noise is either internal and thus the fluctuation-dissipation relation is fulfilled or when the noise is external. The asymptotic behavior of the generalized stochastic oscillator is investigated, and the case of high viscous damping (overdamped limit) is considered. Additional behaviors of the normalized displacement correlation functions different from those for the regular damped harmonic oscillator are observed. In addition, the cases of a constant external force and the force free case are obtained. The validity of the generalized Einstein relation for this process is discussed. The considered fractional generalized Langevin equation may be used to model anomalous diffusive processes including single file-type diffusion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Permeability Evolution of Fractures in Shale in the Presence of Supercritical CO 2

We experimentally examined the impact of supercritical carbon dioxide (scCO 2 ) on fracture permeability and fracture surface characteristics in shales of various compositions. We measured permeability and fracture normal displacement at different effective stresses using both argon and scCO 2 as pore fluids. Both natural fractures and saw cuts in intact samples were used in our study. The permeability and fracture normal displacement decrease after multiple loading/unloading cycles, apparently as the result of inelastic compaction. In samples with high carbonate content, we observe an increase in permeability and fracture surface degradation after more than 3.5 days of exposure to scCO 2 , apparently due to carbonate dissolution. We demonstrate that the sensitivity of permeability to effective normal stress correlates well with the fracture normal displacement. The dependence of permeability on effective normal stress increases after exposure to scCO 2 as the fracture surface became more compliant.

58 GEOSCIENCES↗

Additively Reinforced Thermoformable PETG Composite Sheets for Improved Structural Efficiency

Thermoforming of short-fiber reinforced thermoplastic sheets offers a viable pathway for producing lightweight composite components; however, inherent anisotropy in fiber-reinforced sheets can limit structural performance under multidirectional loading. In this work, short carbon fiber, glass fiber, and hybrid fiber–reinforced PETG sheets were evaluated as candidate feedstock materials for thermoforming, with flexural and tensile testing performed both along the primary fiber direction and in the off-axis orientation to establish baseline stiffness, strength, and anisotropy. As expected, short carbon fiber PETG exhibited the highest stiffness and strength in the primary fiber direction, while all systems showed reduced performance in the off-axis direction. This off-axis performance reduction provides clear justification for the use of additive reinforcement when such thermoformed sheets are intended for structural applications. The intended manufacturing sequence involves thermoforming the reinforced sheet first, followed by the application of additively manufactured lattice reinforcement; therefore, the reinforcement strategy does not impose limitations on sheet formability during thermoforming. Post-forming lattice reinforcement significantly reduced load-normalized displacement by approximately 95–99% relative to non-reinforced sheets and improved weight-normalized stiffness by ~70%. These findings demonstrate that geometry-driven additive reinforcement can effectively compensate for off-axis property reductions in thermoformed PETG composites, enabling enhanced multidirectional structural performance without compromising manufacturability.

Talabi, Isaac [ORNL] (ORCID:0000000340215594)↗

Plasticity Under Pressure Using a Windowed Pressure-Shear Impact Experiment

Many experimental techniques have been developed to determine the compressive strength or flow stress of a material under high strain rate or shock loading conditions. In addition, pressure-shear techniques have been developed that allow for the measurement of the shearing response of materials under pressure. The technique described is similar to the traditional pressure-shear plate-impact experiments except that window interferometry is used to measure both the normal and transverse particle velocities at a sample-window interface. The velocities are measured using the normal displacement interferometer (NDI) for the normal velocity, and the transverse displacement interferometer (TDI) for the transverse velocity. A schematic of the experiment is shown in Figure 1. For our experiment, the diameters of the impactor, sample and window are 31.75 mm. A 3 mm thick Ta-10W flyer is used for all the experiments, and the window material is a 10 mm thick c-cut sapphire. Two types of samples, both polycrystalline Cu and V have been tested and have a nominal thickness of 1.5 mm. For the TDI measurement a 1200 lines/mm grating is etched in the sapphire and a thin ({approx}120 nm) metallic film is deposited over the grating. The sample attached to the film side of the window by application of glue at several locations on the outer circumference of the sample. The experimental result for a Cu experiment is shown in figure 2. Figure 2a shows an example of the interferomentric data from the NDI and TDI measurement taken at the sample/window interface. For the TDI measurement (pink) each fringe is equivalent to a the transverse displacement of 416 nm. The velocity is calculated by taking the derivative as a function of time, and the experimental velocity data are shown in Figure 2b. The flow stress of the material is extracted by using a LLNL hydrodynamics code, ALE3D, and an appropriate strength model. For the Cu experiments, the Mechanical Threshold Model (MTS) is used and can be matched to the transverse velocity profile with parameters that calculate a flow stress of 180 MPa. Similar experiments have also been performed on polycrystalline V and calculate a flow stress of approximately 600 MPa.

36 MATERIALS SCIENCE↗

A triangular thin shell finite element: Linear analysis

The formulation of the linear stiffness matrix for a doubly-curved triangular thin shell element, using a modified potential energy principle, is described. The strain energy component of the potential energy is expressed in terms of displacements and displacement gradients by use of consistent Koiter strain-displacement equations. The element inplane and normal displacement fields are approximated by complete cubic polynomials. The interelement displacement admissibility conditions are met in the global representation by imposition of constraint conditions on the interelement boundaries; the constraints represent the modification of the potential energy. Errors due to the nonzero strains under rigid body motion are shown to be of small importance for practical grid refinements through performance of extensive comparison analyses.

Thomas, G. R.↗

Elastic-plastic deformation of a metal-matrix composite coupon with a center slot

A comprehensive experimental analysis of deformations of the surface of a metal-matrix specimen is reported. The specimen is a 6-ply 0 + or - 45 sub s boron-aluminum tensile coupon with a central slot. Moire interferometry is used for high-sensitivity whole-field measurements of in-plane displacements. Normal and shear strains are calculated from displacement gradients. Displacement fields are analyzed at various load levels from 15% to 95% of the failure load. Deformations of the boron fibers could be distinguished from those of the matrix. Highly localized plastic slip zones occur tangent to the ends of the slot. Shear strains and concurrent transverse compressive strains in the slip zones reach approximately 10% and 1%, respectively. Upon unloading, elastic recovery in surrounding regions causes a reverse plastic shear strain in the slip zone of about 4%. Longitudinal normal strains on the unslotted ligament peak at the slot boundary at about 1% strain. The strain concentration factor at the end of the slot decreases with load level and the advance of plasticity.

Post, D.↗

A triangular element based on generalized potential energy concepts

Stiffness equations are formulated for a doubly-curved triangular thin shell finite element. The strain energy component of the potential energy is first expressed in terms of displacements and displacement gradients with the aid of consistent deep shell strain-displacement equations. The element in-plane and normal displacement fields are approximated by complete cubic polynomials. These functions do not satisfy the interelement displacement admissibility conditions. Satisfaction is forced by the imposition of constraint conditions on the interelement boundaries; the constraints represent the modification of the potential energy. Some numerical results for a pinched cylinder, a cylindrical sphere, and a pinched sphere are examined.

Thomas, G. R.↗

Digital PIV Measurements of Acoustic Particle Displacements in a Normal Incidence Impedance Tube

Acoustic particle displacements and velocities inside a normal incidence impedance tube have been successfully measured for a variety of pure tone sound fields using Digital Particle Image Velocimetry (DPIV). The DPIV system utilized two 600-mj Nd:YAG lasers to generate a double-pulsed light sheet synchronized with the sound field and used to illuminate a portion of the oscillatory flow inside the tube. A high resolution (1320 x 1035 pixel), 8-bit camera was used to capture double-exposed images of 2.7-micron hollow silicon dioxide tracer particles inside the tube. Classical spatial autocorrelation analysis techniques were used to ascertain the acoustic particle displacements and associated velocities for various sound field intensities and frequencies. The results show that particle displacements spanning a range of 1-60 microns can be measured for incident sound pressure levels of 100-130 dB and for frequencies spanning 500-1000 Hz. The ability to resolve 1 micron particle displacements at sound pressure levels in the 100 dB range allows the use of DPIV systems for measurement of sound fields at much lower sound pressure levels than had been previously possible. Representative impedance tube data as well as an uncertainty analysis for the measurements are presented.

Humphreys, William M., Jr.↗

Interfacial sliding near a free surface in a fibrous or layered composite during thermal cycling

This paper presents a simple shear lag model of interfacial sliding at a free surface in a layered or continuous fiber composite. The interface is characterized by a critical interfacial shear stress, tau0, which might represent the critical stress for frictional sliding at a weakly bonded interface, or the shear flow stress of a thin ductile interface layer at a well bonded interface. The history, during heating and cooling, of the relative normal displacement of the reinforcing inclusions and the matrix on a free surface cut normal to the inclusions is calculated and shown to depend on both the absolute value and the temperature dependence of tau0, as well as on the magnitudes of the bulk residual stresses. The variety of possible displacement histories suggests that they are a rich source of information about tau0 and the residual stresses.

Cox, B. N.↗

Transverse Stress Decay in a Specially Orthotropic Strip Under Localizing Normal Edge Loading

Solutions are presented for the stresses in a specially orthotropic infinite strip which is subjected to localized uniform normal loading on one edge while the other edge is either restrained against normal displacement only, or completely fixed. The solutions are used to investigate the diffusion of load into the strip and in particular the decay of normal stress across the width of the strip. For orthotropic strips representative of a broad range of balanced and symmetric angle-ply composite laminates, minimum strip widths are found that ensure at least 90% decay of the normal stress across the strip. In addition, in a few cases where, on the fixed edge the peak shear stress exceeds the normal stress in magnitude, minimum strip widths that ensure 90% decay of both stresses are found. To help in putting these results into perspective, and to illustrate the influence of material properties on load 9 orthotropic materials, closed-form solutions for the stresses in similarly loaded orthotropic half-planes are obtained. These solutions are used to generate illustrative stress contour plots for several representative laminates. Among the laminates, those composed of intermediate-angle plies, i.e., from about 30 degrees to 60 degrees, exhibit marked changes in normal stress contour shape with stress level. The stress contours are also used to find 90% decay distances in the half-planes. In all cases, the minimum strip widths for 90% decay of the normal stress exceed the 90% decay distances in the corresponding half-planes, in amounts ranging from only a few percent to about 50% of the half-plane decay distances. The 90% decay distances depend on both material properties and the boundary conditions on the supported edge.

Fichter, W. B.↗

A compact fiber optics-based heterodyne combined normal and transverse displacement interferometer

While Photonic Doppler Velocimetry (PDV) has become a common diagnostic tool for the measurement of normal component of particle motion in shock wave experiments, this technique has not yet been modified for the measurement of combined normal and transverse motion, as needed in oblique plate impact experiments. In this study, we discuss the design and implementation of a compact fiber-optics-based heterodyne combined normal and transverse displacement interferometer. Like the standard PDV, this diagnostic tool is assembled using commercially available telecommunications hardware and uses a 1550 nm wavelength 2 W fiber-coupled laser, an optical focuser, and single mode fibers to transport light to and from the target. Two additional optical probes capture first-order beams diffracted from a reflective grating at the target free-surface and deliver the beams past circulators and a coupler where the signal is combined to form a beat frequency. The combined signal is then digitized and analyzed to determine the transverse component of the particle motion. The maximum normal velocity that can be measured by this system is limited by the equivalent transmission bandwidth (3.795 GHz) of the combined detector, amplifier, and digitizer and is estimated to be ~2.9 km/s. Finally, sample symmetric oblique plate-impact experiments are performed to demonstrate the capability of this diagnostic tool in the measurement of the combined normal and transverse displacement particle motion.

47 OTHER INSTRUMENTATION↗

An improved transverse shear deformation theory for laminated antisotropic plates

An improved transverse shear deformation theory for laminated anisotropic plates under bending is presented. The theory eliminates the need for an arbitrarily chosen shear correction factor. For a general laminate with coupled bending and stretching, the constitutive equations connecting resultants with average displacements and rotations are derived. Simplified forms of these relations are also obtained for the special case of a symmetric laminate with uncoupled bending. The governing equation for this special case is obtained as a sixth-order equation for the normal displacement requiring prescription of the three physically natural bounday conditions along each edge. For the limiting case of isotropy, the present theory reduces to an improved version of Mindlin's theory. Numerical results are obtained from the present theory for an example of a laminated plate under cylindrical bending. Comparison with results from exact three-dimensional analysis shows that the present theory is more accurate than other theories of equivalent order.

Murthy, M. V. V.↗

Interaction of optical and interface phonons and their anisotropy in GaAs/AlAs superlattices: Experiment and calculations

The angular anisotropy of interface phonons and their interaction with optical phonons in (001) GaAs/AlAs superlattices are calculated and experimentally studied. Experiments were performed by Raman light scattering in different scattering geometries for phonons with the wave vector directed normally to the superlattice and along its layers. Phonon frequencies were calculated by the extended Born method taking the Coulomb interaction into account in the rigid-ion approximation. Raman scattering spectra were calculated in the Volkenshtein bond-polarizability approximation. Calculations confirmed that the angular anisotropy of phonons observed in experiments appears due to interaction (mixing) of optical phonons, in which atoms are mainly displaced normally to superlattices, with interface phonons (TO-IF modes). In the scattering geometry, when the wave vector lies in the plane of superlattice layers, the mixed TO-IF modes are observed under nonresonance conditions. The Raman spectra for TO-IF modes depend on the mixing of atoms at heteroboundaries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of Wear Test Parameters on the Electrical Contact Performance of Brass Alloy/Copper Contactors Under Fretting Wear

Fretting of mated electronic connectors may be due to extreme increase in contact resistance. We present a detailed analysis of contact resistance by fretting experiments using brass alloys/copper contact pairs. The relationship between wear mechanisms and contact resistance was determined. The influence of fundamental factors such as normal load, displacement amplitude, and current on contact resistance change was also evaluated. It was found out that displacement amplitude, normal load, and current are important parameters for infinite lifetime or stable electrical resistance during fretting condition. Influence of displacement amplitude on the electrical contact performance might be affected by wear debris in the contact area. Electric contact performance could be improved by increasing the power current, which could break down the thick oxide film formed. The predicted working lifetime and reliability requirements of the connector were determined to optimize and extend the service life under the working condition.

36 MATERIALS SCIENCE↗

Digital system for dynamic turbine engine blade displacement measurements

An instrumentation concept for measuring blade tip displacements which employs optical probes and an array of micro-computers is presented. The system represents a hitherto unknown instrumentation capability for the acquisition and direct digitization of deflection data concurrently from all of the blade tips of an operational engine rotor undergoing flutter or forced vibration. System measurements are made using optical transducers which are fixed to the case. Measurements made in this way are the equivalent of those obtained by placing three surface-normal displacement transducers at three positions on each blade of an operational rotor.

Kiraly, L. J.↗

Broadband Calibration of Acoustic Emission and Ultrasonic Sensors from Generalized Ray Theory and Finite Element Models

This paper describes a calibration method for acoustic emission and ultrasonic sensors that is effective from 1 kHz to 1 MHz. The method combines generalized ray theory and finite element analysis to model wave propagation at higher and lower frequencies, respectively. A ball impact is used as a calibration source, a thick aluminum plate is used as the test block, and hot glue is used as the couplant. We demonstrate this method on five commercial piezoelectric sensors: Physical Acoustics (PAC) R15a, PAC WSa, Panametrics V101, Panametrics V103, and Valpey-Fisher Pinducer. Our calibration results show that reflections and other wave phases can be more clearly identified with the less-resonant Panametrics sensors. The PAC sensors have the greatest sensitivity and are able to detect surface normal displacements at least down to 1 pm amplitude in the 100s of kHz frequency band. Aperture effect is minimized by the small size of the Pinducer. Our method focuses on the amplitude response of the sensors (phase is ignored) and extends the calibration to a frequency band that is lower than typical analyses. Low frequency information is useful for determining the seismic moment of a seismic source (analogous to the magnitude of an earthquake) and can increase the amount of information acquired in a single recording.

42 ENGINEERING↗