Search NASA⌕ Search

SEARCH · Search NASA

Results for “octane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1953

Free fall and evaporation of N-Octane droplets in the atmosphere as applied to the jettisoning of aviation gasoline at altitude

In connection with proposed rapid jettisoning of aviation gasoline at altitude, a theoretical study was made of the free fall and evaporation of N-octane droplets in the atmosphere ; N-octane was selected for study because of the expected similarity of over-all evaporation behavior of N-octane and gasoline. It was concluded that gasoline (or N-octane) droplets larger than 2000 microns in diameter would be unstable ; terminal speeds and Reynolds numbers were obtained for droplets not larger than 2000 microns at altitudes to 11,000 feet. The motion data were used in the calculation of N-octane evaporation rates under various conditions. It was found that a droplet having an original diameter of 2000 microns would fall about 4000 feet from 6000 feet under NACA standard atmosphere conditions before coming virtually to rest. Finally, it was concluded that temperature effects are of paramount importance; at highest air temperatures a 1000-foot ground clearance would probably be adequate to prevent ground contamination, whereas at lowest air temperatures only an atomizing spray arrangement would prevent ground contamination, irrespective of ground clearance.

FIRE HAZARDS↗
NASA NTRS1940

Testing of high-octane fuels in the single-cylinder airplane engine

One of the most important properties of aviation fuels for spark-ignition engines is their knock rating. The CFR engine tests of fuels of 87 octane and above does not always correspond entirely to the actual behavior of these fuels in the airplane engine. A method is therefore developed which, in contrast to the octane number determination, permits a testing of the fuel under various temperatures and fuel mixture conditions. The following reference fuels were employed: 1) Primary fuels; isooctane and n-heptane; 2) Secondary fuels; pure benzene and synthetic benzine.

Seeber, Fritz↗
NASA NTRS1973

A field ionization study of octan-2-one

Electron-impact studies on deuterated aliphatic ketones have demonstrated that partial H/D randomization tends to occur prior to fragmentation. The scope of the studies is extended to include the kinetics and mechanisms of the fragmentation processes induced by field ionization of octan-2-one at very short times within the very high field in the vicinity of the blade emitter and at longer times in the low field regions.

Derrick, P. J.↗
NASA NTRS1939

Activation of hydrocarbons and the octane number

This report presents an examination of the history of research on engine knocking and the various types of fuels used in the investigations of this phenomenon. According to this report, the spontaneous ignition of hydrocarbons doped with oxygen follows the logarithmic law within a certain temperature range, but not above 920 degrees K. Having extended the scope of investigations to prove hydrocarbons, the curves of the mixtures burned by air should then be established by progressive replacement of pure iso-octane with heptane. Pentane was also examined in this report.

Peschard, Marcel↗
NASA NTRS1938

Engine Performance and Knock Rating of Fuels for High-output Aircraft Engines

Data are presented to show the effects of inlet-air pressure, inlet-air temperature, and compression ratio on the maximum permissible performance obtained on a single-cylinder test engine with aircraft-engine fuels varying from a fuel of 87 octane number to one 100 octane number plus 1 ml of tetraethyl lead per gallon. The data were obtained on a 5-inch by 5.75-inch liquid-cooled engine operating at 2,500 r.p.m. The compression ratio was varied from 6.50 to 8.75. The inlet-air temperature was varied from 120 to 280 F. and the inlet-air pressure from 30 inches of mercury absolute to the highest permissible. The limiting factors for the increase in compression ratio and in inlet-air pressure was the occurrence of either audible or incipient knock. The data are correlated to show that, for any one fuel,there is a definite relationship between the limiting conditions of inlet-air temperature and density at any compression ratio. This relationship is dependent on the combustion-gas temperature and density relationship that causes knock. The report presents a suggested method of rating aircraft-engine fuels based on this relationship. It is concluded that aircraft-engine fuels cannot be satisfactorily rated by any single factor, such as octane number, highest useful compression ratio, or allowable boost pressure. The fuels should be rated by a curve that expresses the limitations of the fuel over a variety of engine conditions.

Rothbrock, A M↗
NASA NTRS1939

Compression-ignition engine performance with undoped and doped fuel oils and alcohol mixtures

Several fuel oils, doped fuel oils, and mixtures of alcohol and fuel oil were tested in a high-speed, single-cylinder, compression-ignition engine to determine power output, fuel consumption, and ignition and combustion characteristics. Fuel oils or doped fuel oils of high octane number had shorter ignition lags, lower rates of pressure rise, and gave smoother engine operation than fuel oils or doped fuel oils of low octane number. Higher engine rotative speeds and boost pressures resulted in smoother engine operation and permitted the use of fuel oils of relatively low octane number. Although the addition of a dope to a fuel oil decreased the ignition lag and the rate of pressure rise, the ensuing rate of combustion was somewhat slower than for the undoped fuel oil so that the effectiveness of combustion was practically unchanged. Alcohol used as an auxiliary fuel, either as a mixture or by separate injection, increased the rates of pressure rise and induced roughness. In general, the power output decreased as the proportion of alcohol increased and, below maximum power, varied with the heating value of the total fuel charge.

Moore, Charles S↗
NASA NTRS1993

Fuel-rich catalytic combustion of a high density fuel

Fuel-rich catalytic combustion (ER is greater than 4) of the high density fuel exo-tetrahydrocyclopentadiene (JP-10) was studied over the equivalence ratio range 5.0 to 7.6, which yielded combustion temperatures of 1220 to 1120 K. The process produced soot-free gaseous products similar to those obtained with iso-octane and jet-A in previous studies. The measured combustion temperature agreed well with that calculated assuming soot was not a combustion product. The process raised the effective hydrogen/carbon (H/C) ratio from 1.6 to over 2.0, thus significantly improving the combustion properties of the fuel. At an equivalence ratio near 5.0, about 80 percent of the initial fuel carbon was in light gaseous products and about 20 percent in larger condensable molecules. Fuel-rich catalytic combustion has now been studied for three fuels with H/C ratios of 2.25 (iso-octane), 1.92 (jet-A), and 1.6 (JP-10). A comparison of the product distribution of these fuels shows that, in general, the measured concentrations of the combustion products were monotonic functions of the H/C ratio with the exception of hydrogen and ethylene. In these cases, data for JP-10 fell between iso-octane and jet-A rather than beyond jet-A. It is suggested that the ring cross-linking structure of JP-10 may be responsible for this behavior. All the fuels studied showed that the largest amounts of small hydrocarbon molecules and the smallest amounts of large condensable molecules occurred at the lower equivalence ratios. This corresponds to the highest combustion temperatures used in these studies. Although higher temperatures may improve this mix, the temperature is limited. First, the life of the present catalyst would be greatly shortened when operated at temperatures of 1300 K or greater. Second, fuel-rich catalytic combustion does not produce soot because the combustion temperatures used in the experiments were well below the threshold temperature (1350 K) for the formation of soot. Increasing the temperature above this value would remove the soot-free nature of the process. Since all the fuels studied show a similar breakdown of the primary fuel into smaller molecular combustion products, this technique can be applied to all hydrocarbon fuels.

Brabbs, Theodore A.↗
NASA NTRS1977

Formation of fatty acids in photochemical conversions of saturated hydrocarbons

Abiogenic synthesis of fatty acids was studied in photochemical conversions of saturated hydrocarbons. It was shown that, in a hydrocarbon water CaCO3 suspension, the action of 254 nm UV rays caused the formation of fatty acids with a maximum number of carbon atoms in the chain not exceeding that in the initial hydrocarbon. Synthesis of acetic, propionic, butyric, valeric, caproic, enanthic and caprylic (in the case of octane) acids occurs in heptane water CaCO3 and octane water CaCO3 systems.

Telegina, T. A.↗
NASA NTRS1982

Formation of oxides of nitrogen in monodisperse spray combustion of hydrocarbon fuels

Experimental results of exit plane NO/NO(x) emissions from atmospheric monodisperse fuel spray combustion are presented. Six different hydrocarbon fuels were studied: isopropanol, n-propanol, n-octane, iso-octane, n-heptane and methanol. The results indicate an optimum droplet size for minimizing NO/NO(x) production for all of the test fuels. At the optimum droplet diameter, reductions in NO/NO(x) relative to the NO(x) occurred at droplet diameters of 55 and 48 microns respectively, as compared to a 50-micron droplet size for isopropanol. The occurrence of the minimum NO(x) point at different droplet diameters for the different fuels appears to be governed by the extent of prevaporization of the fuel in the spray, and is consistent with theoretical calculations based on each fuel's physical properties. Estimates are also given for the behavior of heavy fuels and of polydisperse fuel sprays in shifting the minimum NO(x) point compared to a monodisperse situation.

Nizami, A. A.↗
NASA NTRS1988

Experimental verification of the thermodynamic properties for a jet-A fuel

Thermodynamic properties for a Jet-A fuel were determined by Shell Development Company in 1970 under a contract for NASA Lewis Research Center. The polynomial fit necessary to include Jet-A fuel (liquid and gaseous phases) in the library of thermodynamic properties of the NASA Lewis Chemical Equilibrium Program is calculated. To verify the thermodynamic data, the temperatures of mixtures of liquid Jet-A injected into a hot nitrogen stream were experimentally measured and compared to those calculated by the program. Iso-octane, a fuel for which the thermodynamic properties are well known, was used as a standard to calibrate the apparatus. The measured temperatures for the iso-octane/nitrogen mixtures reproduced the calculated temperatures except for a small loss due to the non-adiabatic behavior of the apparatus. The measurements for Jet-A were corrected for this heat loss and showed excellent agreement with the calculated temperatures. These experiments show that this process can be adequately described by the thermodynamic properties fitted for the Chemical Equilibrium Program.

Graciasalcedo, Carmen M.↗
NASA NTRS1992

Observations of soot during droplet combustion at low gravity - Heptane and heptane/monochloroalkane mixtures

Experimental observations of the combustion of sooting fuel droplets, performed in a drop tower to create a low gravity environment, are reported. Free n-heptane droplets and suspended droplets of heptane, monochloroalkanes, and mixtures of monochloro-octane and heptane were studied. Initial droplet diameters ranged from 0.4 to 1.1. mm. The results suggest that soot may influence droplet vaporization rates. Spherical symmetry of the flame allowed for extended observation of soot agglomerates inside the droplet flame. Effects of slight convective flows were also observed, both through variations of natural convection around the suspended droplets and through variations in the drift velocities of the unsupported droplets. Slight convective flows around the suspended droplets reduced flame luminosity as well as soot accumulation inside the flame and increased droplet vaporization rates. Mixing monochloro-octane with n-heptane demonstrated the effectiveness of n-heptane in reducing soot emissions from the flames of the chlorinated fuels. Finally, trends of initial droplet diameter with burning rate were observed and may be linked to the effect of droplet size upon soot formation inside the flame.

Jackson, G. S.↗
NASA NTRS1940

The Effects of Engine Speed and Mixture Temperature on the Knocking Characteristics of Several Fuels

Six 100-octane and two 87-octane aviation engine fuels were tested in a modified C.F.R. variable-compression engine at 1,500, 2,000 and 2,500 rpm. The mixture temperature was raised from 50 to 300 F in approximately 50 degree steps and, at each temperature, the compression ratio was adjusted to give incipient knock as shown by a cathode ray indicator. The results are presented in tabular form. The results are analyzed on the assumption that the conditions which determine whether a given fuel will knock are the maximum values of density and temperature reached by the burning gases. A maximum permissible density factor, proportional to the maximum density of the burning gases just prior to incipient knock, and the temperature of the burning gases at that time were computed for each of the test conditions. Values of the density factors were plotted against the corresponding end-gas temperatures for the three engine speeds and also against engine speed for several and end-gas temperatures. The maximum permissible density factor varied only slightly with engine speed but decreased rapidly with an increase in the end-gas temperature. The effect of changing the mixture temperature was different for fuels of different types. The results emphasize the desirability of determining the anti knock values of fuels over a wide range of engine and intake-air conditions rather that at a single set of conditions.

Lee, Dana W↗
NASA NTRS1947

Effect of Fuel on Performance of a Single Combustor of an I-16 Turbojet Engine at Simulated Altitude Conditions

As part of a study of the effects of fuel composition on the combustor performance of a turbojet engine, an investigation was made in a single I-16 combustor with the standard I-16 injection nozzle, supplied by the engine manufacturer, at simulated altitude conditions. The 10 fuels investigated included hydrocarbons of the paraffin olefin, naphthene, and aromatic classes having a boiling range from 113 degrees to 655 degrees F. They were hot-acid octane, diisobutylene, methylcyclohexane, benzene, xylene, 62-octane gasoline, kerosene, solvent 2, and Diesel fuel oil. The fuels were tested at combustor conditions simulating I-16 turbojet operation at an altitude of 45,000 feet and at a rotor speed of 12,200 rpm. At these conditions the combustor-inlet air temperature, static pressure, and velocity were 60 degrees F., 12.3 inches of mercury absolute, and 112 feet per second respectively, and were held approximately constant for the investigation. The reproducibility of the data is shown by check runs taken each day during the investigation. The combustion in the exhaust elbow was visually observed for each fuel investigated.

Zettle, Eugene V↗
NASA NTRS1992

Mapping of sea bottom topography

Under suitable conditions the bottom topography of shallow seas is visible in remote sensing radar imagery. Two experiments were performed to establish which remote sensing technique or combination yields optimal imaging of bottom topography and which hydro-meteorological conditions are favorable. A further goal is to gain experience with these techniques. Two experiments were performed over an area in the North Sea near the measuring platform Meetpost Noordwijk (MPN). The bottom topography in the test area is dominated by sand waves. The crests of the sand waves are perpendicular to the coast line and the dominating (tidal-)current direction. A 4x4 sq km wide section of the test area was studied in more detail. The first experiment was undertaken on 16 Aug. 1989. During the experiment the following remote sensing instruments were used: Landsat-Thematic Mapper, and NASA/JPL Airborne Imaging Radar (AIR). The hydro-meteorological conditions; current, wind, wave, and air and water temperature were monitored by MPN, a ship of Rijkswaterstaat (the OCTANS), and a pitch-and-roll WAVEC-buoy. The second experiment took place on 12 July 1992. During this experiment data were collected with the NASA/JPL polarimetric synthetic aperture radar (SAR), and a five-band helicopter-borne scatterometer. Again the hydro-meteorological conditions were monitored at MPN and the OCTANS. Furthermore, interferometric radar data were collected.

Calkoen, C. J.↗