Search NASA⌕ Search

SEARCH · Search NASA

Results for “off-design analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Loiter performance of turbojet-powered aircraft performance determined by off-design cycle analysis

Loitering performance of airplanes equipped with various turbojet engines was analytically investigated. The engines used in this analysis were selected to show the effects of various engine design variables. Engine performance was determined by means of an off-design cycle analysismaking use of experimentally determined component characteristics. The method of off-design cycle analysis is presented herein and is verified by a check with experimental data.

Koutz, Stanley L↗
NASA NTRS1953

Analysis of Off-design Performance of a 16-stage Axial-flow Compressor with Various Blade Modifications

The over-all performance of a 16-stage axial-flow compressor was determined with various stator-blade resettings and a reduction in solidity of the rotor blades in the last three stages. It was shown that little control over the sudden change in slope of the surge-limit line at intermediate speeds was obtained with the blade modifications attempted, except that some change in speed at which the change in slope occurred could be effected by stator-blade resettings. Interstage data indicated that the severe surge limit at intermediate speeds was caused by stall of the inlet stage, which, because of stage interaction effects, resulted in a simultaneous decrease in performance of the following five or six stages. Stage data are presented which indicate the flow and pressure-ratio range over which each stage is required to operate at compressor speeds from 50 to 100 percent of design speed.

COMPRESSORS - AXIAL-FLOW↗
NASA NTRS1952

Loitering and range performance of turbojet-powered aircraft determined by off-design engine cycle analysis

The loitering and range performance of airplanes equipped with several different turbojet engines was analytically investigated by applying the results of off-design cycle analyses to specific airplane characteristics. The method of off-design cycle analysis is presented herein and is verified by a check with experimental data. For all engines considered, the loitering and the range fuel flows obtained with rated tail-pipe nozzle area, variable engine speed operations were within 2 or 3 percent of the optimum fuel flow obtainable with any method of engines operation. The optimum loitering altitude generally occurred between approximately 25,000 and 35,000 feet with corresponding optimum flight Mach numbers of 0.4 to 0.65. In general, the optimum range fuel flows occurred at 3000 to 5000 feet higher altitude and at approximately 0.15 higher flight Mach numbers than the optimum loitering fuel flow.

Koutz, Stanley L↗
NASA NTRS1951

Investigation of Off-design Performance of Shock-in-rotor Type Supersonic Blading

An analysis of the off-design performance of shock-in rotor-type supersonic blading is presented. The over-all losses are assumed divided into two groups;normal-shock losses, and external-wave losses. Throughout the range of relative entrance Mach numbers from 1.35 to starting, the largest losses can be attributed to the normal shock. An improvement in performance would be expected with a reduction of the normal-shock losses by the introduction of external compression waves.

CASCADES, EXPERIMENT↗
NASA NTRS1971

Analysis of transonic airfoils.

A finite difference scheme for the analysis of transonic airfoils at off-design conditions is described. It is the ultimate goal of the investigations to avoid expensive wind tunnel tests by combining the mathematical techniques in a procedure for designing supercritical airfoils so that they will be effective over a wider range of angles of attack and Mach numbers. A mathematical method is considered for computing two-dimensional transonic flows past a prescribed profile. The method can provide accurate results for a comparison with a known shockless regime. The approach gives also data of engineering reliability concerning the location and the strength of shocks at off-design conditions.

Garabedian, P. R.↗
NASA NTRS1973

Computer simulation of shock wave boundary layer interaction

Development of a boundary layer correction for an analysis program previously used by Bauer et al. (1972) to study two-dimensional flow past transonic airfoils at off-design conditions where shocks which interact with the boundary layer appear. Using a method which combines conformal mapping with a finite-difference scheme due to Murman and Cole (1971), an analysis is made of the interaction between shock waves on a supercritical wing section and a turbulent boundary layer, assuming that the shocks are weak and that separation is insignificant. It is shown that relatively simple shock wave/boundary layer interactions of the kind envisioned in this study can be treated by determining the displacement thickness iteratively together with the flow and altering the profile accordingly. It is concluded that the proposed boundary layer correction appears to furnish an essential improvement in cases where both pronounced aft loading and a large enclosed supersonic region of flow are present.

Bauer, F.↗
NASA NTRS1972

A theory of supercritical wing sections, with computer programs and examples.

Mathematical methods for the design of supercritical wings, which depend on the numerical solution of the partial differential equations of two-dimensional gas dynamics, are developed. The main contribution is a computer program for the design of shockless transonic airfoils using the hodograph transformation and analytic continuation into the complex domain. The mathematical theory is described, and a manual for users of the programs is provided. Numerical examples are given and computational results are discussed, and the computer programs themselves are listed. The analysis routine can be used to ascertain whether the profiles behave well at off-design conditions, or to smooth coordinates and obtain a desirable shape more quickly when perfectly shockless flow is not essential.

Bauer, F.↗
NASA NTRS1954

Analytical Study of Losses at Off-design Conditions for a Fixed Geometry Turbine

An analytical investigation was made to determine the off-design loss characteristics of a fixed-geometry turbine of which the experimental performance was known. The method of analysis utilized an effective loss parameter and assumed that the velocity normal to the blade entrance angle was lost as a total-pressure loss. The method also assumed constant tangential component of velocity between the station just upstream and just downstream of the stator and rotor trailing edge. Good correlation between the analytically and experimentally obtained performance was found over the entire map until limiting loading was approached. The large decrease in efficiency at low-speed high pressure ratios and at high-speed low pressure ratios was found in the analysis to be almost entirely due to the rotor incidence and turbine exit whirl losses. From the results of the investigation it was concluded that for turbines designed to operate efficiently at more than one point, the design must compromise rotor incidence angle and exit whirl losses.

Stewart, Warner L↗
NASA NTRS1974

Computer program for predicting off-design performance of centrifugal compressors

Complete knowledge of compressor overall geometry and working fluid total inlet conditions is required for program's use. On given speed line, compressor performance is calculated for range of inlet velocity levels. Working fluid state conditions and flow properties are calculated using mean stream line one-dimensional analysis.

Galvas, M. R.↗
NASA NTRS1972

Drive turbine systems for 20-inch turbofan simulators. 1: Duct turbine design

A study was made to evolve the turbine drive systems for 20-inch turbofan engine simulators. The fan designs used in the simulators included single-stage and two-stage configurations that covered a wide range of rotative speed and power requirement. The objective assumed for the study was to evolve one core turbine design that could drive all of the single-stage fans and, when operated in combination with one duct turbine design, drive all of the two-stage fans. The duct turbine power output is then needed to determine the make-up power required of the core turbine over the range of two-stage fan operating conditions. The duct turbine design analysis is reported and includes the selection of the duct turbine velocity diagram, a description of the blade design, and a determination of its off-design performance. Adjustable stators were found to be quite advantageous to the duct turbine off-design operation. The use of adjustable stators enabled the duct turbine to accommodate fan mass flow at all operating points and caused the duct turbine power output to increase as the total power requirement increased. This in turn resulted in a core turbine make-up power requirement that was not significantly greater than that required for driving the single-stage fans.

Whitney, W. J.↗
NASA NTRS1972

New technology in turbine aerodynamics

A cursory review is presented of some of the recent work that has been done in turbine aerodynamic research at NASA-Lewis Research Center. Topics discussed include the aerodynamic effect of turbine coolant, high work-factor (ratio of stage work to square of blade speed) turbines, and computer methods for turbine design and performance prediction. An extensive bibliography is included. Experimental cooled-turbine aerodynamics programs using two-dimensional cascades, full annular cascades, and cold rotating turbine stage tests are discussed with some typical results presented. Analytically predicted results for cooled blade performance are compared to experimental results. The problems and some of the current programs associated with the use of very high work factors for fan-drive turbines of high-bypass-ratio engines are discussed. Turbines currently being investigated make use of advanced blading concepts designed to maintain high efficiency under conditions of high aerodynamic loading. Computer programs have been developed for turbine design-point performance, off-design performance, supersonic blade profile design, and the calculation of channel velocities for subsonic and transonic flow fields. The use of these programs for the design and analysis of axial and radial turbines is discussed.

Glassman, A. J.↗
NASA NTRS1972

New technology in turbine aerodynamics.

Cursory review of some recent work that has been done in turbine aerodynamic research. Topics discussed include the aerodynamic effect of turbine coolant, high work-factor (ratio of stage work to square of blade speed) turbines, and computer methods for turbine design and performance prediction. Experimental cooled-turbine aerodynamics programs using two-dimensional cascades, full annular cascades, and cold rotating turbine stage tests are discussed with some typical results presented. Analytically predicted results for cooled blade performance are compared to experimental results. The problems and some of the current programs associated with the use of very high work factors for fan-drive turbines of high-bypass-ratio engines are discussed. Computer programs have been developed for turbine design-point performance, off-design performance, supersonic blade profile design, and the calculation of channel velocities for subsonic and transonic flowfields. The use of these programs for the design and analysis of axial and radial turbines is discussed.

Glassman, A. J.↗
NASA NTRS1974

High-transonic-speed transport aircraft study

An initial design study of high-transonic-speed transport aircraft has been completed. Five different design concepts were developed. These included fixed swept wing, variable-sweep wing, delta wing, double-fuselage yawed-wing, and single-fuselage yawed-wing aircraft. The boomless supersonic design objectives of range = 5560 km (3000 nmi), payload = 18,143 kg (40,000 lb), Mach = 1.2, and FAR Part 36 aircraft noise levels were achieved by the single-fuselage yawed-wing configuration with a gross weight of 211,828 kg (467,000 lb). A noise level of 15 EPNdB below FAR Part 36 requirements was obtained with a gross weight increase to 226,796 kg (500,000 lb). The off-design subsonic range capability for this configuration exceeded the Mach 1.2 design range by more than 20%. Although wing aeroelastic divergence was a primary design consideration for the yawed-wing concepts, the graphite-epoxy wings of this study were designed by critical gust and maneuver loads rather than by divergence requirements. The transonic nacelle drag is shown to be very sensitive to the nacelle installation. A six-degree-of-freedom dynamic stability analysis indicated that the control coordination and stability augmentation system would require more development than for a symmetrical airplane but is entirely feasible. A three-plane development plan is recommended to establish the full potential of the yawed-wing concept.

Kulfan, R. M.↗
NASA NTRS1953

Analysis of turbine stator adjustment required for compressor design-point operation in high Mach number supersonic turbojet engines

For turbojet engines designed for flight Mach numbers of 2.5 and 3.0, use of turbine stator adjustment to maintain compressor design-point operation was evaluated analytically to determine the effect on the aerodynamics of the turbine. Since the effect of turbine stator adjustment is to make the turbine design sensitive to the particular engine design conditions selected, in some cases the turbine must be conservatively designed for the high-speed flight condition to assure satisfactory turbine performance at take-off. A new concept, the break-even point, is introduced to provide quick evaluation of the proximity of turbines to the blade-loading limit at any off-design operation.

ENGINES, CONTROL - TURBOJET↗