SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An accurately dimensioned convex ellipsoidal surface, which will become a master after polishing, is fabricated from 316L stainless steel. When polishing of the master is completed, it is suspended in a modified watt bath for electroforming of nickel reflectors.
Optical laser characterization was performed on reflectors for the GigaBREAD and InfraBREAD experiments to compare to the designs and confirm they were machined properly. These slides go over a background of ultralight dark matter, as well as the optical setup to perform the measurements and the results.
Reflector antennas are widely used in communication satellite systems because they provide high gain at low cost. Offset-fed single paraboloids and dual reflector offset Cassegrain and Gregorian antennas with multiple focal region feeds provide a simple, blockage-free means of forming multiple, shaped, and isolated beams with low sidelobes. Such antennas are applicable to communications satellite frequency reuse systems and earth stations requiring access to several satellites. While the single offset paraboloid has been the most extensively used configuration for the satellite multiple-beam antenna, the trend toward large apertures requiring minimum scanned beam degradation over the field of view 18 degrees for full earth coverage from geostationary orbit may lead to impractically long focal length and large feed arrays. Dual reflector antennas offer packaging advantages and more degrees of design freedom to improve beam scanning and cross-polarization properties. The Cassegrain and Gregorian antennas are the most commonly used dual reflector antennas. A computer program for calculating the secondary pattern and directivity of a generalized dual reflector antenna system was developed and implemented at LeRC. The theoretical foundation for this program is based on the use of physical optics methodology for describing the induced currents on the sub-reflector and main reflector. The resulting induced currents on the main reflector are integrated to obtain the antenna far-zone electric fields. The computer program is verified with other physical optics programs and with measured antenna patterns. The comparison shows good agreement in far-field sidelobe reproduction and directivity.
The next generation of space systems will require large apertures in order to image faint targets or cover large areas of Earth. These large apertures must be able to fit inside a launch vehicle fairing, be light enough for launch into orbit, and deploy on orbit with repeatability and reliability. The current state-of-the-art in flight optics is represented by the 4 meter LAMP telescope, with an areal density of 10 km sq m. Development of a Beryllium mirror demonstration article for NGST (Next Generation Space Telescope) at the University of Arizona indicate areal densities of 0.5 kg sq m with flight hardware in the 12 meter range. With progressive improvements in existing deployment, packaging, and structural technologies, the size of optics and reflectors will continue to increase, while mass is reduced. However, without a breakthrough in materials, packaging and/or deployment technologies, the goal for Gossamer structures of 0.1 kg sq m is unachievable for the near and mid-term NASA missions. Membrane technology provides the best hope of achieving such low areal densities. In combination with advances in membrane materials and structures, development of revolutionary techniques for deployment systems can provide significant improvements in large aperture technology. In this paper, the results of a six-month Phase I research effort to demonstrate the application of thin film NiTi to aerospace-qualified membrane and mesh materials are presented. Deposition of shape memory thin film was achieved Astromesh (trademark) metal mesh and CP-1, and optical-quality polymer membrane. Not only was full-coating deposition demonstrated, but also small segment deposition which holds potential for local surface control. Deployment of these materials was also demonstrated, setting the stage for the development of a larger test article.
Performance of X-ray reflectors affects that of X-ray mirrors. Modern X-ray mirrors have thousands of reflectors to gain large effective area. Evaluation of the reflectors is an important process in production of the mirrors. A diffraction pattern dominates reflector image when the parallel optical beam illuminates the reflector along its optical axis because the reflectors are used at grazing incident angles of around 1 deg and their effective width are 1–10 mm. A diffraction pattern from the entire reflector surface can be acquired at once with the aid of a lens. The diffraction pattern holds information of the surface profiles of the reflectors. To quantitatively evaluate the reflectors with the diffraction pattern, we created a diffraction pattern model by the wave optics with the ideal surface profile and fitted it to data. As a result, a correlation between fitting residual and the normal vector distribution of the surface profile was found. With our method, the reflectors can be evaluated and sorted out more efficiently.
A schematic diagram of the electrostatically figured membrane reflector (EFMR) is presented in Figure 1. Here, active reflector figure control is exercised via electrostatic stresses which operate between the reflector and a second surface called the -command surface. The command surface is located a short distance behind the reflector and is pulled firmly into an approximate paraboloid by a network of guy wires or comparable structure. This same surface supports insulated conducting segments which are individually addressable by dedicated control voltages. The control voltages are, in turn, collectively biased with respect to the reflector. The reflector, tensioned by a rigid rim at the perimeter, is distended toward the command surface by the bias. The resulting command surface potential distribution, and hence the electrostatic stress distribution acting on the reflector, is continuously and rapidly refined via the control voltages so as to produce and maintain a precise parabolic reflector figure. Optical reflector figure measurements provide the data necessary for computer-supervised figure control. Finally, in order to prevent command surface discharging by photons and charged particles, the command surface is completely enclosed by a conducting shroud of which the reflector serves as the front side. Guy wires to the back-side shroud can be used to figure the command surface. The complete shroud is not pictured in Figure 1.
Stable optical solar reflector for spacecraft thermal control, summarizing simulated exposures results
Telemetry data are presented for two communications hybrid satellites, Spacenet I and Spacenet II, collected to determine the long-term temperature trend and associated solar absorptance degradation of the optical solar reflectors (OSRs). A thermal model was used to calculate the thermal sensitivity of various OSR components to changes in the solar absorptance and to determine absolute values of solar absorptance. The separation of the data into sunlit and nonsunlit periods made it possible to confirm the hypothesis that degradation occurs under the catalytic activity of direct sunlight on the spacecraft contaminants. The differences found between the degradation rates for Spacenet-I and Spacenet-II satellites and between the present results and published reports on other satellites are considered to be related to variations in the volume of spacecraft contaminants.
Additional frequency bands are needed to satisfy requirements related to the rapid growth of satellite communications, and the utilization of the 30/20 GHz frequencies is being considered. The present investigation is concerned with the experimental verification phase of an antenna technology study sponsored by NASA. The feasibility of narrow (0.3 degree) directive beam scanning over the entire continental U.S. (CONUS) from a single antenna at 30/20 GHz is demonstrated. The POC (Proof-of-Concept) model is based on an employment of an offset shaped dual reflector optics. The main reflector and the subreflector are both fabricated from aluminum. Attention is given to feed array and beam-forming network, multiple beam antenna range tests, an analysis, and test results.
A folded optics reflector system could mitigate problems associated with the pointability and controllability of the large UHF antenna for MSAT. Such a system is comprised of a parabolic main reflector and a hyperboloidal subreflector (Cassegrain arrangement) or an ellipsoidal subreflector (Gregorian arrangement), either of which brings the feed closer to the main reflector. By shaping the subreflector and the main reflector, an improved scan capability might be achieved and the size of the required feed aperture-per-beam could be reduced. In such a shaped dual reflector system, the need for overlapping cluster feed arrangement and its concomitant beam forming network could be removed. In this system, a relatively low gain feed element together with the shaped subreflector would be sufficient to produce the required high illumination taper that at the main reflector.
A 20 GHz downlink satellite antenna design is described. The aperture simultaneously radiates 18 fixed, 0.3 deg width pencil beams directed at 18 cities distributed over CONUS for Trunking Service. All beams use the same trunk frequency allocation for 18 reuses of the band. The same aperture also radiates six additional 0.3 deg spot beams for Customer Premises Service (CPS) for TDMA beam hopping operation to small terminals anywhere in CONUS. Each CPS beam scans one sector of CONUS and all six beams are frequency reused in a CPS band. Offset dual reflector optics are used with a feed array and multiport beam forming network (BFN). For so many frequency reuses, sidelobes per beam must be 30 to 40 dB down over CONUS. Novel dual reflector optics were devised with shaped surfaces providing low aberrations for all beam positions over CONUS (+ or - 12 BW by + or - 5 BW). Scan loss under 1 dB is calculated with nearly constant sidelobes. For each beam position, a 7-element cluster of feeds is activated in the feed array with coefficients adjusted by the BFN to maintain low sidelobes and thus high beam isolation for frequency reuse.
Experimental studies using a pulsed LED, Cerenkov source, and a 100 ps laser were made of various photomultipliers and discriminator combinations. In addition, a new type of neodymium-YAG frequency doubled laser was used as the basis for the development of a stable, short pulse, high repetition rate laser system. This laser was then used in conjunction with atomic clocks to study the effect of gravitational potential on elapsed time. Avenues to promote the development of international cooperation in the area of lunar laser ranging were also explored.
PLOPS system designed to provide high-resolution measurement of change in optical length from optical-system source to any optical reflector, including diffuse reflector. Serves as adjustable optical ruler, providing high resolution in measurements of small and large changes in distance to target. Use is broad and includes most measurement situations requiring information on length, vibration, and their derivatives. Applications include building dynamics, remote sensing of vibrations in such systems as turbine-based machinery, monitoring of structural dynamics, noncontacting sensing of surface contours, measurement of large strains as in earthquake monitoring, measurement of atmospheric dynamics and turbulence, high-resolution sensing of humidity, detection of surface acoustic waves by optical microscopy, and related areas.
An optical pulse stretcher and a mathematical algorithm for the detailed calculation of its design and performance is disclosed. The optical pulse stretcher has a plurality of optical cavities, having multiple optical reflectors such that an optical path length in each of the optical cavities is different. The optical pulse stretcher also has a plurality of beam splitters, each of which intercepts a portion of an input optical beam and diverts the portion into one of the plurality of optical cavities. The input optical beam is stretched and a power of an output beam is reduced after passing through the optical pulse stretcher and the placement of the plurality of optical cavities and beam splitters is optimized through a model that takes into account optical beam divergence and alignment in the pluralities of the optical cavities. The optical pulse stretcher system can also function as a high-repetition-rate (MHz) laser pulse generator, making it suitable for use as a stroboscopic light source for high speed ballistic projectile imaging studies, or it can be used for high speed flow diagnostics using a laser light sheet with digital particle imaging velocimetry. The optical pulse stretcher system can also be implemented using fiber optic components to realize a rugged and compact optical system that is alignment free and easy to use.
Accuracy of laser ranging to optical reflectors on lunar surface
Receiver for optical communications uses rough reflector instead of diffraction-limited reflector customarily thought necessary for such systems. Rough reflector collects and focuses optical signal. Other receiver components include narrow-passband optical filter to reject out-of-band background radiation, spatial filter to limit receiver field of view, optical-detector array (typically two concentric detectors), and postdetection processor to reconstruct transmitted message.
A Cassegrainian solar concentrator, using a 7-meter diameter primary reflector, was analyzed in three forms: (1) an unmodified Cassegrainian, (2) the Ritchey-Chretien configuration, and (3) the unmodified Cassegrainian with a non-imaging tertiary reflector. Optical performance was not significantly improved with the Ritchey-Chretien; however, the tertiary resulted in significant improvement in intercept factor and optical efficiency. The effects of misalignment of the secondary and tertiary reflectors on the optical performance of the collector were also analyzed.
The invention is a device that provides a high resolution measurement of the change in optical phase length from the device optical system source to an optical reflector. The invention consists of a optical phase locked loop that uses a laser beam as a carrier of an intensity modulated energy source. The novelty of the invention appears to lie in the overall combination of elements which provide high resolution without loss of wide dynamic range. The invention does not depend on coherent reflection from a target, and thus can measure targets that do not have special preparation or corner reflectors. The use of carrier modulation achieves high resolution without the problems of high speed pulse duration systems. Thus the invention has the advantages of simplicity, low cost, and small size without sacrificing resolution.