Search NASA⌕ Search

SEARCH · Search NASA

Results for “optimal recovery”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Optimal recovery from microburst wind shear

The flight path of a twin-jet transport aircraft is optimized in a microburst encounter during approach to landing. The objective is to execute an escape maneuver that maintains safe ground clearance and an adequate stall margin during the climb-out portion of the trajectory. A cost function penalizing rate of climb deviations from a nominal value and rate of elevator deflection produces qualitatively good results in a variety of microburst encounters. The optimal maneuver is a gradual pitch-up that ceases near the core of the microburst, followed by a slight reduction in pitch attitude in the tailwind area of the microburst. A minimum airspeed constraint in the optimization prevents excessive airspeed loss in very severe microbursts. The aircraft equations of motion include short-period dynamics, so that the optimization solves directly for the control surface deflections required to achieve the optimal flight paths.

Mulgund, Sandeep S.↗
NASA NTRS1993

Optimal recovery from microburst wind shear

Severe low-altitude wind variability represents an infrequent but significant hazard to aircraft taking off or landing. During the period from 1964 to 1985, microburst wind shear was a contributing factor in at least 26 civil aviation accidents involving nearly 500 fatalities and over 200 injuries. A microburst is a strong localized downdraft that strikes the ground, creating winds that diverge radially from the impact point. The physics of microbursts have only been recently understood in detail, and it has been found that effective recovery from inadvertent encounters may require piloting techniques that are counter-intuitive to flight crews. The goal of this work was to optimize the flight path of a twin-jet transport aircraft encountering a microburst during approach to landing. The objective was to execute an escape maneuver that maintained safe ground clearance and an adequate stall margin during the climb-out portion of the trajectory.

Mulgund, Sandeep S.↗
NASA NTRS1986

Utilization of non-conventional systems for conversion of biomass to food components: Recovery optimization and characterizations of algal proteins and lipids

Protein isolate obtained from green algae (Scenedesmus obliquus) cultivated under controlled conditions was characterized. Molecular weight determination of fractionated algal proteins using SDS-polyacrylamide gel electrophoresis revealed a wide spectrum of molecular weights ranging from 15,000 to 220,000. Isoelectric points of dissociated proteins were in the range of 3.95 to 6.20. Amino acid composition of protein isolate compared favorably with FAO standards. High content of essential amino acids leucine, valine, phenylalanine and lysine makes algal protein isolate a high quality component of closed environment life support system (CELSS) diets. To optimize the removal of algal lipids and pigments supercritical carbon dioxide extraction (with and without ethanol as a co-solvent) was used. Addition of ethanol to supercritical CO2 resulted in more efficient removal of algal lipids and produced protein isolate with a good yield and protein recovery. The protein isolate extracted by the above mixture had an improved water solubility.

Karel, M.↗
NASA NTRS2007

Tactile Sensory Supplementation of Gravitational References to Optimize Sensorimotor Recovery

Integration of multi-sensory inputs to detect tilts relative to gravity is critical for sensorimotor control of upright orientation. Displaying body orientation using electrotactile feedback to the tongue has been developed by Bach-y- Rita and colleagues as a sensory aid to maintain upright stance with impaired vestibular feedback. This investigation has explored the effects of Tongue Elecrotactile Feedback (TEF) for control of posture and movement as a sensorimotor countermeasure, specifically addressing the optimal location of movement sensors.

Black, F. O.↗
NASA NTRS1974

Optimal and suboptimal control technique for aircraft spin recovery

An analytic investigation has been made of procedures for effecting recovery from equilibrium spin conditions for three assumed aircraft configurations. Three approaches which utilize conventional aerodynamic controls are investigated. Included are a constant control recovery mode, optimal recoveries, and a suboptimal control logic patterned after optimal recovery results. The optimal and suboptimal techniques are shown to yield a significant improvement in recovery performance over that attained by using a constant control recovery procedure.

Young, J. W.↗
NASA NTRS2017

Stall Recovery Guidance Using Fast Model Predictive Control

Based on a detailed analysis of recent loss-of-control events, the Aircraft State Awareness Joint Safety Analysis Team has identified the need to develop algorithms and display strategies to provide control guidance for recovery from approach-to-stall or stall. In order to be effective, such guidance should enhance the pilots ability to execute the Federal Aviation Administrations recommended stall recovery procedure. This paper explores the use of a fast model predictive control algorithm that determines near optimal recovery guidance, which quantifies the aircraft configuration and situation dependent recovery information required to maximize the effectiveness of the recovery. This information includes the magnitude of the initial pitch down maneuver, the specific amount of airspeed and thrust needed before pulling out of the recovery dive, as well as the maximum pitch-up rate that can be sustained without causing a secondary stall. The algorithm was integrated and tested with an in-house desktop simulator that implements the General Transport Aircraft model and the associated stall aircraft dynamics. Preliminary results are presented to demonstrate the use of the proposed approach as a recovery aid for pilots.

predictive control↗
NASA NTRS2011

Soyuz 23 Return Samples: Assessment of Air Quality Aboard the International Space Station

Six mini-grab sample containers (m-GSCs) were returned aboard Soyuz 23 because of concerns that new air pollutants had been present in the air and these were getting into the water recovery system. The Total Organic Carbon Analyzer had been giving increasing readings of total organic carbon (TOC) in the potable water, and it was postulated that an increased load into the system was responsible. The TOC began to decline in late October, 2010. The toxicological assessment of 6 m-GSCs from the ISS is shown in Table 1. The recoveries of 13C-acetone, fluorobenzene, and chlorobenzene from the GSCs averaged 73, 82, and 59%, respectively. We are working to understand the sub-optimal recovery of chlorobenzene.

James, John T.↗
NASA NTRS1987

EUREX D: An expert system for failure diagnosis and recovery in the TCS of the European retrievable carrier EURECA

An expert system for diagnosis and recovery of failures in the Freon cooling loop of the European retrievable experiment carrier EURECA is described. The system demonstrates the feasibility of a functional scope of expert diagnostic systems which appears to be essential for practical applications of such systems in space technology. The scope includes early warning and treatment of incomplete information, fault tolerance, identification of failure superpositions, intelligent reaction to unforeseen events, and detailed status display for optimal recovery action.

Kellner, A.↗
NASA NTRS2017

A Method for Estimating Meteorite Fall Mass from Weather Radar Data

Techniques such as weather RADAR, seismometers, and all-sky cameras allow new insights concerning the physics of meteorite fall dynamics and fragmentation during "dark flight", the period of time between the end of the meteor's luminous flight and the concluding impact on the Earth's surface. Understanding dark flight dynamics enables us to rapidly analyze the characteristics of new meteorite falls. This analysis will provide essential information to meteorite hunters to optimize recovery, increasing the frequency and total mass of scientifically important freshly-fallen meteorites available to the scientific community. We have developed a mathematical method to estimate meteorite fall mass using reflectivity data as recorded by National Oceanic and Atmospheric Administration (NOAA) Next Generation RADAR (NEXRAD) stations. This study analyzed eleven official and one unofficial meteorite falls in the United States and Canada to achieve this purpose.

Laird, C.↗
NASA NTRS2019

Safe and Optimal Techniques Enabling Recovery, Integrity, and Assurance

There is a trend in the aviation industry to go from federated to integrated computing systems. Combining a number of traditional stand-alone federated systems into an integrated common platform (called Integrated Modular Avionics, IMA) has the benefit of increased power efficiency, reduced support hardware, and reduced cabling. However, changing from federated to integrated has a significant impact on the system architecture and hence the process of how avionic systems are to be analyzed. Traditional approaches to safety analysis become inefficient when functional boundaries can no longer be assumed for failure independence and fault isolation. In this report, we describe a tool that we developed to accelerate the safety engineer's ability to perform safety analysis of IMA systems through modeling, as well as optimize the system engineer's ability to develop a system through architecture synthesis. This work was the result of a three-year research effort called SOTERIA (Safe and Optimal Techniques Enabling Recovery, Integrity, and Assurance). We developed a compositional modeling language that supports rapid development, modification, and evaluation of architectures. The modeling language is structured such that the end-user defines a library of components with information on component reliability, connectivity, and fault propagation logic. The system model is built by instantiating the components from the library, connecting the components, and identifying the top-level faults of interest. Our tool is compositional in that the end-user only needs to define safety aspects at the component level. The tool takes the model and automatically synthesizes both the qualitative and quantitative safety analyses. We go further by allowing users to describe system information such as components to use in an architecture and their connection compatibility and automatically synthesize an architecture that meets the top-level probability target adhering to end-user specified constraints. This capability allows users to rapidly explore a design space..

Siu, Kit Y.↗
NASA NTRS2002

Optimal Aircraft Control Upset Recovery With and Without Component Failures

This paper treats the problem of recovering sustainable nondescending (safe) flight in a transport aircraft after one or more of its control effectors fail. Such recovery can be a challenging goal for many transport aircraft currently in the operational fleet for two reasons. First, they have very little redundancy in their means of generating control forces and moments. These aircraft have, as primary control surfaces, a single rudder and pairwise elevators and aileron/spoiler units that provide yaw, pitch, and roll moments with sufficient bandwidth to be used in stabilizing and maneuvering the airframe. Beyond this, throttling the engines can provide additional moments, but on a much slower time scale. Other aerodynamic surfaces, such as leading and trailing edge flaps, are only intended to be placed in a position and left, and are, hence, very slow-moving. Because of this, loss of a primary control surface strongly degrades the controllability of the vehicle, particularly when the failed effector becomes stuck in a non-neutral position where it exerts a disturbance moment that must be countered by the remaining operating effectors. The second challenge in recovering safe flight is that these vehicles are not agile, nor can they tolerate large accelerations. This is of special importance when, at the outset of the recovery maneuver, the aircraft is flying toward the ground, as is frequently the case when there are major control hardware failures. Recovery of safe flight is examined in this paper in the context of trajectory optimization. For a particular transport aircraft, and a failure scenario inspired by an historical air disaster, recovery scenarios are calculated with and without control surface failures, to bring the aircraft to safe flight from the adverse flight condition that it had assumed, apparently as a result of contact with a vortex from a larger aircraft's wake. An effort has been made to represent relevant airframe dynamics, acceleration limits, and actuator limits faithfully, since these contribute to the lack of agility and control power that plays an important role in defining what can be achieved with the vehicle when it is in extremis.

Sparks, Dean W.↗
NASA NTRS2021

Thermoelectric System Economics - The Apex: New Paradigms in Manufacturing and Interface Performance Relationships Driving System Cost Optimizations

Thermoelectric energy recovery systems require cost-optimized designs with high thermal and thermoelectric (TE) performance to surmount common commercialization barriers controlling the acceptance of thermoelectric generator (TEG) systems. Recent work has addressed this requirement with new analytic tools and paradigms that allow integrated TEG cost-performance analysis and optimization. New work herein has identified the existence of optimized TE element design (i.e., TE element length) for minimizing TEG cost and provides design guidelines associated with critical thermal and electrical contact resistance effects and TE manufacturing sensitivities. Once optimum hot-side heat flux criteria are satisfied, this work highlights the tradeoffs between interface resistance effects and manufacturing cost effects in determining optimum-cost TE element lengths, and then quantifies the increase in optimum-cost TE lengths as manufacturing costs become more sensitive to TE element lengths. Optimized TE element design criteria and key non-dimensional design parameters (i.e., [𝐶′′′LTE/𝐶′′], [TE/con], [con/(TE,aveLTE)]) driving the design are presented and explained showing the interdependencies between manufacturing cost parameters and thermal and electrical interface impacts on integrated TE cost-performance analysis and design. Comprehensive TEG system cost-performance relationships clearly demonstrate the two parameters that most greatly impact the TEG system cost are heat exchanger costs ($/(W/K)) and TE hot side heat flux. Reducing heat exhanger cost from $1/(W/K) to $0.5/(W/K) can decrease TEG system cost by $2/W to $4/W depending on TE hot side heat fluxes from 4-10 W/cm2. The impact of TE hot side heat flux on TEG system cost is larger; reducing TE system cost by factors of 2-4 as TE hot side heat flux increases from 4 W/cm2 to high levels around 18 W/cm2. The levels of thermal contact resistance and electrical contact resistance required to even approach the critical TEG system cost level of $1/W are characterized by con = 1.0 x 10-10 -m2 and r = 0.1, respectively. This not only lowers TEG costs, but it also makes the TEG system costs less sensitive to TE manufacturing dependences on TE element length. New design paradigms and relationships create holistic, integrated TE performance-cost models that enhance understanding of crucial interrelationships between component costs, TE design parameters and material properties, heat exchanger design parameters, interfacial heat flux, and now thermal and electrical interface effects in minimizing TEG system costs.

Hendricks, Terry J.↗
NASA NTRS2010

Optimal Flow Control Design

In support of the Blended-Wing-Body aircraft concept, a new flow control hybrid vane/jet design has been developed for use in a boundary-layer-ingesting (BLI) offset inlet in transonic flows. This inlet flow control is designed to minimize the engine fan-face distortion levels and the first five Fourier harmonic half amplitudes while maximizing the inlet pressure recovery. This concept represents a potentially enabling technology for quieter and more environmentally friendly transport aircraft. An optimum vane design was found by minimizing the engine fan-face distortion, DC60, and the first five Fourier harmonic half amplitudes, while maximizing the total pressure recovery. The optimal vane design was then used in a BLI inlet wind tunnel experiment at NASA Langley's 0.3-meter transonic cryogenic tunnel. The experimental results demonstrated an 80-percent decrease in DPCPavg, the reduction in the circumferential distortion levels, at an inlet mass flow rate corresponding to the middle of the operational range at the cruise condition. Even though the vanes were designed at a single inlet mass flow rate, they performed very well over the entire inlet mass flow range tested in the wind tunnel experiment with the addition of a small amount of jet flow control. While the circumferential distortion was decreased, the radial distortion on the outer rings at the aerodynamic interface plane (AIP) increased. This was a result of the large boundary layer being distributed from the bottom of the AIP in the baseline case to the outer edges of the AIP when using the vortex generator (VG) vane flow control. Experimental results, as already mentioned, showed an 80-percent reduction of DPCPavg, the circumferential distortion level at the engine fan-face. The hybrid approach leverages strengths of vane and jet flow control devices, increasing inlet performance over a broader operational range with significant reduction in mass flow requirements. Minimal distortion level requirements are met using vanes alone, avoiding engine stall and increasing robustness of this hybrid inlet flow control approach. This design applies to aerospace applications needing flush-mounted boundary-layer-ingesting inlets.

Allan, Brian↗
NASA NTRS2015

Process Control for Precipitation Prevention in Space Water Recovery Systems

The ability to recover and purify water through physiochemical processes is crucial for realizing long‐term human space missions, including both planetary habitation and space travel. Because of their robust nature, rotary distillation systems have been actively pursued by NASA as one of the technologies for water recovery from wastewater primarily comprised of human urine. A specific area of interest is the prevention of the formation of solids that could clog fluid lines and damage rotating equipment. To mitigate the formation of solids, operational constraints are in place that limits such that the concentration of key precipitating ions in the wastewater brine are below the theoretical threshold. This control in effected by limiting the amount of water recovered such that the risk of reaching the precipitation threshold is within acceptable limits. The water recovery limit is based on an empirically derived worst case wastewater composition. During the batch process, water recovery is estimated by monitoring the throughput of the system. NASA Johnson Space Center is working on means of enhancing the process controls to increase water recovery. Options include more precise prediction of the precipitation threshold. To this end, JSC is developing a means of more accurately measuring the constituent of the brine and/or wastewater. Another means would be to more accurately monitor the throughput of the system. In spring of 2015, testing will be performed to test strategies for optimizing water recovery without increasing the risk of solids formation in the brine.

Sargusingh, Miriam↗
NASA NTRS2015

Design of the Brine Evaporation Bag for Increased Water Recovery in Microgravity

The existing water recovery system on the International Space Station (ISS) is limited to 75% reclamation; consequently, long duration space missions are currently unfeasible due to the large quantity of water necessary to sustain the crew. The Brine Evaporation Bag (BEB) is a proposed system to supplement the existing water recovery system aboard the ISS that can to increase water recovery to 99%. The largest barrier to high water recovery is mineral scaling inside the water recovery equipment, which leads to equipment failure; therefore, some water must remain to keep the minerals dissolved. This waste stream is liquid brine containing salts, acids, organics, and water. The BEB is designed to recover this remaining water while protecting the equipment from scale. The BEB consists of a sealed bag containing a hydrophobic membrane that allows water vapor and gas to pass through. It is operated under vacuum, heated, and continuously filled with brine to boil away the water. The water vapor is recovered and the solids are contained inside the bag for disposal. The BEB can dry the brine to a solid block. Ongoing work includes improving the design of the BEB and the evaporator to prevent leaks, maximize the rate of water removal, and minimize energy use and weight. Additional testing will determine whether designs are heat- or mass-transfer limited and the optimal water recovery rate.

Brine Evaporation Bag↗
NASA NTRSDate not supplied

Comprehensive Digital Twin of a Macro-fluidic Electrochemical Reactor to Optimize the Electrochemical-based Recovery of O2 from Metabolic CO2

Future long-duration missions will require a sustainable and efficient system capable of yielding a minimum of 75% O 2 recovery from metabolic CO 2 to achieve self-sufficiency for long space missions beyond Earth's low orbit. A Macro-fluidic Electrochemical Reactor (MFECR) development effort to electrochemically recover O 2 from CO 2 is underway at NASA Marshall Space Flight Center (MSFC) to increase current O 2 recovery efficiency and reduce air revitalization (AR) system complexity at the International Space Station (ISS) habitat and future long missions. The authors have developed and deployed a digital twin of an actual single cell of the MFECR via a comprehensive 3D multiphysics model that thoroughly replicates the exact configuration and fluid/material domains of the MFECR. This model's electrochemical physics consists of multicomponent-multiphase electrochemical-driven reactions leading to CO 2 conversion to C 2 H 4 and CO along with the formation of H 2 on the cathode in parallel with the generation of O 2 and H 2 O on the anode. This electrochemical model is coupled with all the physics phenomena involved in the process, including but not limited to fluid and non-ideal mass transfer of reactant and product species in free and porous media, convective/conduction/radiative heat transfer, and conduction of DC electrical current with Joule heating generation. The digital twin has proved to be an essential tool for performing different qualitative studies, including the effect of reducing the height (increasing the respect ratio) of the serpentine walls, leading to a further redesign of the EDU (the newly redesigned MFECR EDU has been fabricated and is expected to be used in future tests), the evaluation of setting different MFECRs connected in series, and the assessment of feeding air directly to the MFECR skipping the preceding metabolic CO 2 separation from air. The MFECR's test stand is fully automated and equipped with several inline measurements (flow, pressure, temperature, pH, component concentration) systems on all six MFECR's IO streams, allowing reliable experimental validation of the model, parametric determination of all electrochemical reactions, and process optimization.

Jesus A Dominguez↗