SEARCH · Search NASA

Results for “oxygen partial pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Influence of temperature, oxygen partial pressure, and microstructure on the high-temperature oxidation behavior of the SiC Layer of TRISO particles

Tristructural isotropic (TRISO)-coated fuel particles are designed for use in high-temperature gas-cooled nuclear reactors, featuring a structural SiC layer that may be exposed to oxygen-rich environments over 1000 °C. Surrogate TRISO particles were tested in 0.2–20 kPa O 2 atmospheres to observe the differences in oxidation behavior. Oxide growth mechanisms remained consistent from 1200–1600 °C for each P O$_2$ , with activation energies of 228 ± 7 kJ/mol for 20 kPa O 2 and 188 ± 8 kJ/mol for 0.2 kPa O 2 . At 1600 °C, kinetic analysis revealed a change in oxide growth mechanisms between 0.2 and 6 kPa O2. In 0.2 kPa O 2 , oxidation produced raised oxide nodules on pockets with nanocrystalline SiC. Oxidation mechanisms were determined using Atom probe tomography. Active SiC oxidation occurred in C-rich grain boundaries with low P O$_2$ , leading to SiO 2 buildup in porous nodules. Here, this phenomenon was not observed at any temperature in 20 kPa O 2 environments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS2026

In-suit CO2 Washout Test System (ICWTS) for CO2 Washout Verification in Spacesuits

Since the time of Mercury, Gemini, and Apollo, NASA has been performing CO 2 washout verification of spacesuits with Human in the Loop (HITL) test methods. Classically, the only instrumentation both with the accuracy and response time necessary was that of external mass spectrometers or medical gas analyzers fed by a long capillary line from the oro-nasal region within the suit. The helmet CO 2 washout configuration including the challenges posed by variation of a suited human subject frequently created difficulty in capturing adequate breath by breath data. For example, a nasal cannula could be worn with reasonable comfort however it posed the following challenges: (1) impeded the test subject’s ability to do a proper Valsalva maneuver; (2) frequently provided a corrupted waveform with relative movement; (3) precluded the ability to evaluate the Flow Weighted Average (FWA) at subject interface. A mouthpiece could be used in lieu of a cannula but posed challenges as well: (1) created potential disturbances of the flow field; (2) precluded the test subject from speaking during usage; and (3) presented comfort issues limiting the duration of test points. These challenges made it impractical to use a mouthpiece for anything other than short lab ambient environment tests. Technology development and NASA investment have afforded new capabilities to address some of these measurements providing improved data collection and are implemented in the In-suit CO 2 Washout Test System (ICWTS) which provides suit inlet/outlet pressure, temperature, relative humidity, partial pressure of oxygen, partial pressure of CO 2 , and flow measurement coupled with the acquisition of the inspired PPCO 2 including the ability for FWA measurement. This test system, coupled with use of the In-suit Respiration Mannequin Assembly (IRMA) and Computational Fluid Dynamics (CFD) combine to provide a full picture of the in-suit oro-nasal flow field and effectiveness of CO 2 washout in a spacesuit design.

Colin Campbell↗

NASA NTRS2026

In-suit CO 2 Washout Test System (ICWTS) for CO 2 Washout Verification in Spacesuits

Colin Campbell↗

DOE OSTI2025

Understanding Oxide–Metal Interactions During Hot Isostatic Pressing to Diffusion Bond Aluminum Alloy 6061 Plates

The interaction between Mg, Si, and Al 2 O 3 during hot isostatic pressing diffusion bonding of aluminum alloy 6061 (AA6061) plates was investigated through thermodynamic calculations and experimental microstructural characterization. Thermodynamic calculations as functions of temperature, pressure, and composition revealed that the interaction among Mg, Si, and Al 2 O 3 yields Mg 2 Si and either MgO + Al or MgAl 2 O 4 + Al, facilitating the reduction of Al 2 O 3 and allowing Al/Al metallic bonds to form. Total pressure variation had a negligible influence on the oxygen partial pressure, and consequently, the reaction product formation. Oxygen partial pressure variation as a function of temperature and initial amount of Al 2 O 3 determined the formation of either MgO or MgAl 2 O 4 . Experimental Hot Isostatic Pressure (HIP) bonding at 723 K and 833 K under a constant pressure of 1017 atm documented the cooling rate-dependent formation of β–Mg 2 Si precipitates. High-resolution transmission electron microscopy imaging and selected area electron diffraction patterns verified the formation of β–Mg 2 Si and MgO at the interface but did not detect MgAl 2 O 4 . In conclusion, findings from this study clarify the role of thermochemical interactions in oxide disruption and bonding mechanisms during HIP diffusion bonding of AA6061 and provide guidance for optimizing joining processes for monolithic nuclear fuel assemblies.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Microstructure-Based Degradation Modeling in Solid Oxide Cells

The presentation is intended for a graduate class in Georgia Southern University taught by Dr. Hayri Sezer on electrochemistry, SOFC and Li ion battery. It summaries NETL's recent works on microstructure-based modeling of degradation in solid oxide cells. It covers the degradation mechanism of Ni coarsening, Ni migration and the build-up of oxygen partial pressure inside the electrolyte. The phase-field models developed for Ni coarsening and migration are reviewed and the results are compared to experiments in literature to examine different diffusion mechanisms (Ni self-diffusion, Ni(OH)2 diffusion in pores and Ni(OH) surface diffusion) and driving forces (Ni(OH)x concentration and Ni-YSZ contact angle change). It also demonstrates the developed model for oxygen partial pressure and shows that the predicted oxygen partial pressure can explain the Ni oxidation in the hydrogen electrode and crack growth on the electrolyte-oxygen electrode interface under certain operating conditions.

nickel coarsening↗

DOE OSTI2025

Microstructure-based modeling of inner oxygen pressure in solid oxide electrolysis cells: Analysis of electrode delamination and mitigation

One major degradation mechanism during long-term operation of solid oxide electrolysis cells (SOECs) is delamination of oxygen electrodes (OEs). The driving force for the electrode delamination could be the generated high inner oxygen pressure near the electrode-electrolyte interface during operation. However, the effects of transport properties and electrode thickness on the inner oxygen partial pressure are not well understood. Here a microstructure-based electrochemical model, which includes the conduction of electrons and oxygen ions coupled with Butler-Volmer-type chemical reactions at triple-phase-boundaries (TPBs), is employed to investigate the oxygen pressure in lanthanum strontium manganate (LSM)-based SOECs. The model is applied to both two-dimensional (2D) prototype microstructures and three-dimensional (3D) realistic microstructures, and the oxygen pressure is analyzed as a function of transport properties and electrode thickness under both potentiostatic and galvanostatic operations. The simulation results suggest strategies to suppress electrode delamination. The simulation results are compared to an analytical solution, and the discrepancies are attributed to the Butler-Volmer-type kinetics included in the microstructure-based model.

25 ENERGY STORAGE↗

DOE OSTI2025

Vacancy-Dependent Diffusion Mechanism in Oxygen-Defective SrFeO 3 Perovskite Materials: First-Principles Density Functional Theory and Experimental Approach

Understanding oxygen diffusion at the atomic scale in SrFeO 3−δ perovskites is crucial for developing oxygen storage materials with optimal performance. Such materials are required to have high stability, corrosion resistance, and acceptable oxygen storage capacity at moderate operating temperatures and pressures. Here, in this study, we used first-principles density functional theory and thermogravimetric analysis to study the vacancy-dependent oxygen diffusion in oxygen-deficient SrFeO 3−δ (δ = 0, 0.065, 0.125, 0.25, 0.5) perovskites. The electronic structures, including the partial- and spin-resolved density of states, for different SrFeO 3−δ phases were calculated and compared with available experimental and theoretical results. By mapping the migration pathways, we investigated diffusion mechanisms and calculated the energy barriers for oxygen diffusion in cubic, orthorhombic, and brownmillerite phases of SrFeO 3−δ perovskites. Using the calculated energy barriers, we deduced the diffusion time scales and diffusion coefficients within SrFeO 3−δ . A diffusion coefficient on the order of 10 –8 m 2 /s was obtained for SrFeO 2.875 . We experimentally investigated the roles of temperature and oxygen partial pressures on the redox kinetics and deduced the kinetics rate and diffusion density, which agreed well with the calculated values for the density of diffusing oxygen vacancy in the lattice. Our results showed that the energy barrier tends to reduce at higher oxygen concentrations. Our results serve as an important guideline for designing oxygen storage materials with optimal redox kinetics.

chemical looping with oxygen uncoupling (CLOU)↗

DOE OSTI2025

Structure–property relations of binary ferrite melts

Molten ferrite systems are used in the smelting and refining processes in steelmaking, to reduce the loss of metals in slags and to accelerate reaction rates. Here, high-energy x-ray diffraction experiments have been performed on aerodynamically levitated molten spheres of 43BaO–57FeO X and 43SrO–57FeO X at 1873 K using laser beam heating. The composition was varied within the range of x = 1–1.5 by changing the oxygen partial pressure of the levitation gas. The corresponding x-ray pair distribution functions have been interpreted using empirical potential structure refinement (EPSR) modeling. In oxygen-rich melts (x = 1.5), our EPSR models indicate very similar structures for the different alkaline-earth liquids, with both the Ba–O and Sr–O coordination numbers to be ∼8.4 and the total Fe–O coordination numbers ∼5.7. However, our models show that in reducing environments, the Fe 3+ and Fe 2+ ions exhibit very different behaviors in the Ba- and Sr-ferrite liquids. In the Ba-ferrite melt, the Fe 3+ –O coordination number decreases from 5.7 (at x = 1.5) to 5.2 (at x = 1.07), whereas Fe 2+ –O remains constant at ∼5.0 across the same compositional range. In the Sr melts, both the Fe 2+ –O and Fe 3+ –O coordination numbers rise from ∼5.7 (at x = 1.5) to 6.3 (at x = 1.07). All models show the structures to be heterogeneous with intertwined nanometer sized clusters or channels of Ba/Sr–O and Fe–O polyhedra that grow as oxygen content is reduced. Changes in the viscosity and electrical properties are interpreted in terms of the number of bridging and non-bridging oxygens associated with FeO 4 tetrahedra and concentration of charge carriers, respectively.

Benmore, Chris J. [Argonne National Laboratory (AN↗

NASA NTRS2003

Ultra-High-Temperature Ceramics Evaluated for Aeropropulsion Use

Ultra-high-temperature ceramics (UHTC) are a group of materials consisting of zirconium diboride (ZrB2) or hafnium diboride (HfB2) plus silicon carbide (SiC), and in some instances, carbon (C). They offer a combination of properties that make them candidates for airframe leading edges on sharp-bodied reentry vehicles. These UHTCs perform well in the environment for such applications (i.e., air at low pressures). The purpose of this study at the NASA Glenn Research Center was to examine three of these materials under conditions more representative of a propulsion environment: that is, higher oxygen partial pressure and total pressure. Relatively long, multiple-exposure cycles were emphasized. We completed an in-house study of ZrB2 plus 20 vol% SiC (abbreviated as ZS), ZrB2 plus 14 vol% SiC and 30 vol% C (ZSC), and SCS-9a SiC fiber-reinforced ZrB2 plus 20 vol% SiC (ZSS). HfB2-based compositions were not included in the study because of their high cost. The capability of UHTC for propulsion applications must be compared with that of mature, available, and commercially used ceramics such as silicon nitride (e.g., AS-800) to put things in proper perspective. In terms of mechanical properties, UHTCs fall short in terms of strength and fracture toughness. At about 1300 C, the creep resistance of ZS appears to be superior to the creep resistance reported for AS-800. However, the stress rupture life for Si3N4 under stress and temperature conditions similar to those used in this study is measured in hundreds of hours. Because of oxidation, ZS could not achieve such lives. In terms of oxidation resistance, acceptable amounts of material recession in 1 hour to thousands of hours, depending on the specific propulsion application, are on the order of 100 to 300 mm. This converts to an acceptable range of parabolic recession rate constants kp" of approximately less than or equal to 10(exp -1) to 10(exp -2) square millimeters per hour for a 1-hr application. For a 100-hr application, an acceptable range of kp" would be less than or equal to those values divided by 100. For the more oxidation resistant ZS material, measured parabolic recession rate constants were 4.7 x 10(exp -3) millimeters per hour at 1327 C, 7.8 x 10(exp -2) square millimeters per hour at 1627 C, and 1.3 millimeters per hour at 1927 C. Thus, recession rate constants for ZS are acceptable at 1327 C for a 1-hr application, but here silicon nitride is a superior material. At 1627 C, ZS oxidation is marginal for a 1-hr application, but dimensional growth would be an issue. In a 100-hr application, ZS cannot be considered at any temperature. Our cursory examination of thermal shock, both from a theoretical and experimental viewpoint, indicated that the ZS and ZSC UHTCs are inferior to AS-800 silicon nitride. On the basis of this limited study, UHTCs are not ready to be considered as aeropropulsion materials for any applications longer than a few minutes. Current materials suffer from aggressive oxidation and moisture attack (Quynhgiao Nguyen, NASA Glenn, and Raymond C. Robinson, QSS Group, Inc., Cleveland, OH, 2002, private communication), and they are susceptible to thermal shock. For long-term propulsion applications, major improvements in environmental durability are needed. Work is in progress to improve the oxidation resistance of UHTC materials.

Stanley R Levine↗

DOE OSTI2026

Effects of oxygen on the tensile properties and fracture behavior of the Ta-10 W refractory alloy at quasi-static and impact strain rates

This study investigates effects of pre-charged oxygen at levels up to ∼1750 ppm on the tensile properties of the refractory alloy Ta-10 W. Tests were conducted at temperatures to 1100 °C and strain rates from quasi-static (∼10−3 s−1) to impact (∼103 s−1). At all temperatures, ductility decreased with increasing oxygen concentration and could be visually identified as a ductile-to-brittle transition (DBT). Additionally, for a given oxygen concentration, ductility was lower at impact strain rate than at quasi-static. The DBT was accompanied by a change from ductile transgranular to more brittle modes, intergranular and transgranular cleavage. The oxygen concentrations associated with the DBT depend on test temperature and strain rate. However, the transitions themselves are not sharp and cannot be defined as occurring at a specific oxygen concentration. At impact strain rates, ductility is relatively insensitive to test temperatures in the range 300–1100 °C with similar embrittling effects of oxygen; however, oxygen has a more severe embrittling effect at room temperature. This behavior is reversed at quasi-static strain rates where the embrittling effect of oxygen is more severe at elevated temperatures than at room temperature. It appears this difference is related to the kinetics of oxygen diffusion to grain boundaries and crack tips. Specimens that were not pre-charged with oxygen but tensile tested in various partial pressures of oxygen underwent dynamic embrittlement during the test, with the degree of embrittlement increasing as the partial pressure of oxygen in the environment increased. Consistent with such a mechanism, ductility increased with increasing strain rate for a given oxygen partial pressure, which would be the reverse if only intrinsic dislocation mobilities were controlling.

Miller, Roger [ORNL] (ORCID:0000000172155851)↗

DOE OSTI2026

Unraveling Defect-Dependent Conductivity-Type Switching in CuFe 2 O 4 for Enhanced Photoelectrocatalytic Reduction of Benzaldehyde

Photoelectrocatalytic (PEC) reduction provides a sustainable route for upgrading biomass-derived feedstocks with reduced energy requirements, yet remains largely unexplored beyond hydrogen evolution and CO 2 reduction due to the scarcity of stable photocathodes. Here, we report a defect-engineered CuFe 2 O 4 photocathode that enables directly quantified PEC reduction of benzaldehyde to benzyl alcohol using a singlecomponent, earth-abundant oxide. By controlling annealing temperature and oxygen partial pressure, CuFe 2 O 4 is systematically tuned from n-type to p-type conductivity. Electrochemical measurements, X-ray and ultraviolet photoelectron spectroscopy, and firstprinciples defect calculations collectively show that oxygen-rich annealing conditions suppress deep donor-type oxygen vacancies while stabilizing shallow acceptor-type copper vacancies, resulting in enhanced hole concentration and improved charge transport. In a mixed acetonitrile/water electrolyte employing 1,4-benzoquinone as a redox mediator, the optimized CuFe 2 O 4 photocathode achieves stable photoelectrochemical operation over 18 h under continuous illumination with a benzyl alcohol production rate of 2.57 μmol/h at −0.50 V vs Ag/AgNO 3 , corresponding to a Faradaic efficiency of 51.3%. This PEC approach lowers the required applied potential by ∼1 V compared to traditional electrocatalytic methods, offering a more energy-efficient route for carbonyl reduction. These findings establish CuFe 2 O 4 as a viable photocathode platform for sustainable photoelectrocatalytic organic transformations under mild reaction conditions.

benzaldehyde reduction↗

DOE OSTI2026

Pyrite (001) Interface Chemistry is Controlled by a Sulfoxy Termination

Pyrite (FeS 2 ) is the most common sulfide mineral on Earth, forming through inorganic reactions in the crust and oceanic hydrothermal systems and via microbially driven processes in anaerobic sediments. The pyrite–water interface is the site of a wide range of adsorption and reaction processes in Earth systems including oxidation that dramatically affects the geochemistry of surface waters and influences global carbon and oxygen cycles. Mechanistic geochemical models of pyrite interfacial reactivity, however, are limited by the lack of experimentally derived atomistic structures of the reduced and reacting surfaces. Here, in this work, we reveal the atomic-scale structure of the pyrite (001)-water interface that forms at very low oxygen partial pressures, relevant to suboxic environments in Earth. The interface structure and surface speciation were obtained using the crystal truncation rod method supported by ambient-pressure photoelectron spectroscopy and density functional theory calculations. The surface is dominantly composed of disulfide groups bound to a single oxygen atom, forming a sulfoxy group that has no known molecular or bulk mineral analog. This surface is interpreted as the first step in the oxidative dissolution of pyrite. The sulfoxy group is readily protonated through surface acid–base reactions that alter the structure of interfacial water and the free energy of interfacial reactions. Surface iron sites are not oxidized. Surprisingly, this interface can likely develop in equilibrium with bulk pyrite in some reducing and acidic solutions. This termination is therefore likely representative of pyrite surfaces under a vast range of experimental, industrial and Earth conditions.

oxidation↗

DOE OSTI2024

The atomic-level structure and stability of interfaces of Pt nanoparticles in alumina: An experimental and computational evaluation

The atomic-level structure of interfaces between Pt and a transition form of Al2O3 were studied using a combination of electron microscopy and first principles calculations. A model system of Pt nanoprecipitates in Al2O3 were formed in sapphire wafers via high-energy ion implantation of Pt followed by thermal annealing at 1000 °C in air. The Pt nanoparticles took the form of tetrahedra and truncated tetrahedra primarily bound by {111}Pt facets. The high prevalence of these facets motivated the development of density functional theory (DFT) based models of (111)Pt interfaces with six different chemical terminations of ( 2 ¯ 01 ) θ-alumina. The atomic-level structure of the Pt/Al2O3 interfaces was characterized with aberration-corrected scanning transmission electron microscopy (STEM) and the experimental images were compared to STEM image simulations of the DFT models. The model interface with Pt bonded to oxygen-terminated θ-Al2O3, with the Pt located on top of the O and with an underlying layer of octahedral Al, provided the best match to the experimental images. This interfacial termination is also the most stable for the thermal annealing conditions used based on thermodynamic calculations of the interfacial energy as a function of temperature and oxygen partial pressure. This experimentally verified model provides a basis for improving models of Pt/γ-alumina interfaces.

Clauser, A L↗

DOE OSTI2025

LASSO for CALPHAD Model Selection Enables Data-Efficient Thermodynamic Modeling: An Application in Thermochemical Hydrogen Production Materials

Phenomenological CALPHAD (CALculation of PHAse Diagrams) models, widely used for multicomponent materials, often contain a considerable number of parameters and require fitting using data from a relatively small number of experimental measurements or theoretical calculations. Sometimes these parameters are introduced for the purpose of improving model fits but without clear physical justification, which leads to overparametrized models with poor generalization performance. Automated approaches for optimal model selection based on the available data therefore become critical. Here, in this work, a least absolute shrinkage and selection operator (LASSO)-based approach is developed for model selection by leveraging the linearity of the CALPHAD model with respect to its parameters to convert the model selection and fitting to a LASSO minimization problem. We demonstrate its utility for thermodynamic modeling of thermochemical hydrogen (TCH) production materials using lanthanum strontium manganite (LSM) as an example. Various TCH-relevant properties, including oxygen stoichiometry as a function of oxygen partial pressure, enthalpy of reduction, and entropy of reduction, are successfully predicted with reasonable accuracy using a minimal set of model parameters. Importantly, the model selection and fitting involve minimal human decision; it can therefore be applied to high-throughput DFT defect calculations and yield efficient workflows for TCH material modeling and optimization.

CALPHAD↗

DOE OSTI2026

First-principles thermodynamic assessment of Sr-containing secondary phase formation in strontium-substituted lanthanum manganites for solid oxide cell applications

Sr-secondary phase formation is a potentially significant degradation mode with direct impact upon solid-oxide cell (SOC) commercial viability. A first-principles based thermodynamic study was performed for La 1−x Sr x MnO 3±δ (LSM) perovskites to assess their stability against formation of different Sr-secondary phases, including SrO, SrCrO 4 , SrSO 4 , SrCO 3 , and Sr(OH) 2 , for SOC applications. The Sr-secondary phase formation reaction free energies were determined via a thermodynamic model by combining ab initio lattice dynamics calculations for the solid phases and ab initio thermodynamic data for the gas phases. The current approach expands the previously reported thermodynamic modeling studies by integrating first-principles based point defect equilibria into the thermodynamic analysis. The modeling results obtained using this new approach indicate an increased tendency to form the SrO oxide upon decreasing the oxygen partial pressure. Additionally, the enhancing factors to form the Sr-related secondary phase from the associated SrO activity in LSM are further quantified by considering the equilibrium of SrO reacting with the contaminant gas species as a function of temperature and pressure.

defect thermodynamics modeling↗

DOE OSTI2026

Epitaxial growth and physical properties of Bi 2 Ru 2 O 7 thin films on YSZ(111) substrates

We systematically investigated the growth of Bi 2 Ru 2 O 7 thin films on a Y-stabilized ZrO 2 (111) substrate using pulsed laser deposition by mapping the influence of growth temperature and oxygen partial pressure on phase stability, lattice parameters, and cation ratio. The results show that the epitaxial stabilization requires a minimum growth temperature, which is rather insensitive to the pressure. Meanwhile, the Bi:Ru ratio decreases when increasing growth temperature or decreasing pressure. By constructing the temperature–pressure phase diagram, an optimal growth window within the epitaxial phase was established. On the other hand, the electrical resistivity remains at a similar level within the epitaxial phase with only subtle changes to the temperature dependence, indicative of the robustness of the conductivity against composition variation. Our study provides a foundation for future investigations on thin films and heterostructures that utilize Bi 2 Ru 2 O 7 .

Crystallography↗

DOE OSTI2026

Benchtop Autonomous Electrochemical Characterization System for Combinatorial Thin-Film Solid Oxide Electrodes

The design of materials for electrochemical energy conversion is complicated by a vast search space of candidate materials and multifaceted property requirements: multicarrier conductivity, stability, and catalytic activity are all necessary but rarely intersect. Although self-driving laboratories are rapidly rising to address such material optimization problems, the required infrastructure for integrated, large-scale robotic facilities can be cost-prohibitive. Here we develop and evaluate a closed-loop measurement system for efficient screening of proton-conducting oxide electrodes for ceramic fuel cells and electrolyzers, building on top of an existing benchtop instrument and integrating techniques for rapid impedance measurement and automated analysis. This system exemplifies a “minimum viable” self-driving implementation that can deliver substantial benefits with relatively simple infrastructure. Combinatorial thin-film microelectrode libraries are characterized with a recently developed joint time-domain and frequency-domain impedance measurement technique, which provides an order-of-magnitude acceleration relative to conventional impedance spectroscopy. The distribution of relaxation times is extracted from impedance data and analyzed without human intervention. These results feed an active learning and Bayesian optimization process that learns to predict electrochemical impedance as a function of material composition, measurement temperature, oxygen partial pressure, and electrical bias, which further reduces the screening time by tenfold with optimized experimental sequences. We apply this system to Ba⁡(Co,Fe,Zr,Y)⁢O 3−𝛿 combinatorial libraries and evaluate its effectiveness for learning material property trends and optimizing expensive-to-evaluate properties such as activation energy. This offers insights into key methodological aspects of practical autonomous experimentation, including surrogate model validation, cost-aware acquisition functions, and high-throughput data interpretation. Our results demonstrate the efficacy of the system for rapidly gathering information, but also highlight real-world experimental challenges of thin-film degradation and numerical instability in surrogate models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Porous Interlayers that Getter Surface-Segregating Species for Improved Silver Wetting, Adhesion, and Electrical Contact on Stainless Steel SOFC Components

Here, porous nickel interlayers or porous platinum interlayers were shown to promote the wetting, spreading, and adhesion of silver on alumina-forming ferritic stainless steel (AFFSS) and chromia-forming ferritic stainless steel (CFFSS). These interlayers resulted in dense, crack-free AFFSS|Ag-Ni|CFFSS and AFFSS|Ag-Pt|CFFSS braze joints that, after 300 h in 650 °C air, displayed shear strengths up to 70 MPa similar to, or larger than, those of AFFSS|Ag-CuO|CFFSS or AFFSS|Ag|CFFSS joints subjected to identical treatment. Similarly, after exposure to 25 cycles of (50 switches between) 12 h of 650 °C air and 12 h of 650 °C 4%H 2 –96%N 2 , AFFSS|Ag-Ni|CFFSS and AFFSS|Ag-Pt|CFFSS braze joints displayed shear strengths significantly larger than those of AFFSS|Ag-CuO|CFFSS or AFFSS|Ag|CFFSS joints subjected to identical treatment. In addition, nickel and platinum were found to chemically getter surface-segregating steel constituents, particularly Al from the AFFSS. As a result, Ag-Ni and Ag-Pt electrical contact resistances on AFFSS and CFFSS substrates were several orders of magnitude lower than those of conventional Ag-CuO reactive air brazes or Heraeus C8710 Ag contact pastes. Together, these results suggest that Ag-Pt and especially Ag-Ni may be useful for the fabrication of durable joints, seals, and/or electrical contacts in electrical/electrochemical devices exposed to high temperatures and/or variable oxygen partial pressure environments.

36 MATERIALS SCIENCE↗