Search NASA⌕ Search

SEARCH · Search NASA

Results for “p-i-n architecture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Surface reaction for efficient and stable inverted perovskite solar cells

We report perovskite solar cells (PSCs) with an inverted structure (often referred to as the p-i-n architecture) are attractive for future commercialization due to their easily scalable fabrication, reliable operation, and compatibility with a wide range of perovskite-based tandem device architectures. However, the power conversion efficiency (PCE) of p-i-n PSCs falls behind n-i-p (or normal) structure counterparts. This large performance gap could undermine efforts to adopt p-i-n architectures, despite their other advantages. Given the remarkable advances in perovskite bulk materials optimization over the past decade, interface engineering has become the most important strategy to push PSC performance to its limit. Here, we report a reactive surface engineering approach based on a simple post-growth treatment of 3-(Aminomethyl)pyridine (3-APy) on top of a perovskite thin film. First, the 3-APy molecule selectively reacts with surface FA+, reducing perovskite surface roughness and surface potential fluctuations associated with surface steps/terraces. Second, the reaction product on the perovskite surface decreases the formation energy of charged iodine-vacancies, leading to effective n-type doping with a reduced work function in the surface region. With this reactive surface engineering, the resulting p-i-n PSCs obtained a PCE over 25%, along with retaining 87% of the initial PCE after over 2400 h of one-sun operation at about 55 degrees C in air.

14 SOLAR ENERGY↗
DOE OSTI2020

Perovskite Quantum Dot Solar Cells: Mapping Interfacial Energetics for Improving Charge Separation

Colloidal halide perovskite nanocrystals or quantum dots (QDs) show similar defect tolerance as thin film perovskite materials with added nanoscale phenomena. Perovskite QD solar cells have demonstrated efficiencies of 16.6%, greater than that of any other QD material system. While the efficiency lags behind the best thin-film perovskite devices, these solar cells could have advantages over the thin-film versions in terms of processability, phase stability, and high open-circuit voltages. However, some operating principles behind perovskite quantum dot device stacks and the associated electric field properties are still unknown. Here, we characterize the junction structure within perovskite QD solar cells, by exposing functioning cross-sections and using nanometer-scale Kelvin probe force microscopy to offer insight into the selection and performance of charge selective contacts. We also evaluated various solar cell device architectures with different selective contacts to isolate the role of each junction in device performance. We show that in high-performance n-i-p architectures, both electron- and hole-transport layer (HTL) interfaces possess a strong electric field, but in the case of the inverted p-i-n architecture, we find that high interfacial recombination at the HTL/QD junction is responsible for subpar device performance. Perovskite QD and thin film materials can synergistically be combined to offer more design flexibility in PV devices, and here we demonstrate that the interface between perovskite thin films and QDs are relatively benign and amenable for synergistic device design.

14 SOLAR ENERGY↗
DOE OSTI2025

Flexible transparent conducting electrodes unexpectedly influence MAPbI 3 film morphology and perovskite solar cell performance

Fabricating perovskite solar cells (PSCs) on plastic substrates will enable cost-effective manufacturing of lightweight and portable energy systems. Here, we study the influence of flexible transparent conductive electrodes (TCEs) on the methylammonium lead iodide (MAPbI3) film morphology and PSC performance. Three types of TCEs on polyethylene terephthalate (PET) are compared: a custom-made AgNWs/indium zinc oxide hybrid TCE and two commercial substrates with indium tin oxide (ITO) or metal/insulator/metal (MIM) as the TCE. Using the same p-i-n architecture and hole transport layer (HTL), we find that PSCs fabricated on the hybrid TCE show better performance and stability compared to those made on commercial TCEs. The PSC performance enhancement is attributed to the superior structural and optical properties of MAPbI3 film deposited on the hybrid TCE, which is explained by the surface energy difference of the HTL. While it is anticipated that solar cell performance can be affected by TCEs’ transmittance and sheet resistance as they determine light absorption and carrier transport, respectively, our finding of TCE influencing the morphology and crystallinity of MAPbI3 film, and hence PSC performance, is unexpected.

14 SOLAR ENERGY↗
DOE OSTI2020

A sensitive and robust thin-film x-ray detector using 2D layered perovskite diodes

Solid-state radiation detectors, using crystalline semiconductors to convert radiation photons to electrical charges, outperform other technologies with high detectivity and sensitivity. Here, we demonstrate a thin-film x-ray detector comprised with highly crystalline two-dimensional Ruddlesden-Popper phase layered perovskites fabricated in a fully depleted p-i-n architecture. It shows high diode resistivity of 10 12 ohm·cm in reverse-bias regime leading to a high x-ray detecting sensitivity up to 0.276 C Gy air –1 cm –3 . Such high signal is collected by the built-in potential underpinning operation of primary photocurrent device with robust operation. The detectors generate substantial x-ray photon–induced open-circuit voltages that offer an alternative detecting mechanism. Furthermore, our findings suggest a new generation of x-ray detectors based on low-cost layered perovskite thin films for future x-ray imaging technologies.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Two-dimensional perovskite templates for durable, efficient formamidinium perovskite solar cells

We present a design strategy for fabricating ultrastable phase-pure films of formamidinium lead iodide (FAPbI 3 ) by lattice templating using specific two-dimensional (2D) perovskites with FA as the cage cation. When a pure FAPbI 3 precursor solution is brought in contact with the 2D perovskite, the black phase forms preferentially at 100°C, much lower than the standard FAPbI 3 annealing temperature of 150°C. X-ray diffraction and optical spectroscopy suggest that the resulting FAPbI 3 film compresses slightly to acquire the (011) interplanar distances of the 2D perovskite seed. The 2D-templated bulk FAPbI 3 films exhibited an efficiency of 24.1% in a p-i-n architecture with 0.5–square centimeter active area and an exceptional durability, retaining 97% of their initial efficiency after 1000 hours under 85°C and maximum power point tracking.

14 SOLAR ENERGY↗
DOE OSTI2022

Deterministic fabrication of 3D/2D perovskite bilayer stacks for durable and efficient solar cells

Realizing solution-processed heterostructures is a long-enduring challenge in halide perovskites because of solvent incompatibilities that disrupt the underlying layer. By leveraging the solvent dielectric constant and Gutmann donor number, we could grow phase-pure two-dimensional (2D) halide perovskite stacks of the desired composition, thickness, and bandgap onto 3D perovskites without dissolving the underlying substrate. Characterization reveals a 3D–2D transition region of 20 nanometers mainly determined by the roughness of the bottom 3D layer. Thickness dependence of the 2D perovskite layer reveals the anticipated trends for n-i-p and p-i-n architectures, which is consistent with band alignment and carrier transport limits for 2D perovskites. Here we measured a photovoltaic efficiency of 24.5%, with exceptional stability of T 99 (time required to preserve 99% of initial photovoltaic efficiency) of >2000 hours, implying that the 3D/2D bilayer inherits the intrinsic durability of 2D perovskite without compromising efficiency.

14 SOLAR ENERGY↗
DOE OSTI2023

Sensitive and robust thin film X-ray detector using 2D layered perovskite diodes

A radiation detector includes a p-i-n architecture including a p-type contact layer, an n-type contact layer, and an intrinsic layer between the p-type contact layer and the n-type contact layer. The intrinsic layer includes a thin film comprising a highly crystalline 2D layered perovskite material. The radiation detectors according to embodiments of the present disclosure generate high open circuit voltages, have good detecting photon density limits and high sensitivities, and can be self-powered.

Tsai, Hsinhan↗
DOE OSTI2026

Phosphonic-Acid-Reinforced Polymer Hole Transport Layers for Deployable p-i-n Perovskite Photovoltaics

The long-term durability prospects of halide perovskite solar cells are rapidly improving; however, the interface between the hole transport layer (HTL) and the perovskite remains a source of degradation. Alone, polymer- or carbazole-based HTLs suffer from incomplete coverage of the underlying indium tin oxide glass, leading to degradation and compromised performance. Here, we show a multi-HTL approach whereby a polymer HTL is reinforced using a phosphonic acid modification leading to better protection of the buried perovskite interface and more columnar growth of perovskite film, resulting in an ~40-mV open-circuit voltage (VOC) improvement indicative of suppressed interfacial recombination across multiple p-i-n device architectures. Solar cells with this reinforced HTL show higher tolerance to several accelerated stress tests. We report, among the best durabilities for unencapsulated cells, a T90 ~3,000 h (T80 ~5,900 h) at 65 degrees C under continuous 1.2 sun AM 1.5G illumination and maximum power point tracking, representing a nearly 4-fold increase compared with [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz)-only devices. Furthermore, we deployed a device with this reinforced HTL on a cube satellite, with long-duration operational space testing results exceeding T80 for the complete mission duration of ~100 days in low Earth orbit.

14 SOLAR ENERGY↗
DOE OSTI2022

Polymer Hole Transport Material Functional Group Tuning for Improved Perovskite Solar Cell Performance

As lead halide perovskites (LHPs) continue to achieve success as a light-harvesting material in perovskite solar cells (PSCs), exploring and understanding other materials in the device stack become increasingly important. Particularly, selection of suitable hole transport materials (HTMs) that demonstrate high performance and stability is imperative in the design of P-I-N PSCs. Presented here are a family of 12 structurally related polymers based on either fluorene or carbazole main chains with select aromatic side groups that introduce tunable properties for use in PSCs. How properties such as the highest occupied molecular orbital energy level, conductivity, glass-transition temperature, and wettability of the HTM affect the PSC performance is explored. Devices that incorporate the polymer HTMs perform well relative to PTAA in benchmark P-I-N PSC architectures while exhibiting similar or superior stability under accelerated aging studies. The relative synthetic simplicity and resultant performance of the HTMs in PSCs coupled with the ability to customize properties with different functional groups demonstrates the potential of this family of HTMs for a variety of LHP materials.

14 SOLAR ENERGY↗
DOE OSTI2023

Highly efficient bifacial single-junction perovskite solar cells

Bifacial photovoltaics (PV) harvest solar irradiance from both their front and rear surfaces, boosting energy conversion efficiency to maximize their electrical power production. For single-junction perovskite solar cells (PSCs), the performance of bifacial configurations is still far behind that of their state-of-the-art monofacial counterparts. Here, in this paper, we report on highly efficient, bifacial, single-junction PSCs based on the p-i-n (or inverted) architecture. We used optical and electrical modeling to design a transparent conducting rear electrode for bifacial PSCs to enable optimized efficiency under a variety of albedo illumination conditions. The bifaciality of the PSCs was about 91%–93%. Under concurrent bifacial measurement conditions, we obtained equivalent, stabilized bifacial power output densities of 26.9, 28.5, and 30.1 mW/cm 2 under albedos of 0.2, 0.3, and 0.5, respectively. We further showed that bifacial perovskite PV technology has the potential to outperform its monofacial counterparts with higher energy yields and lower levelized cost of energy (LCOE).

14 SOLAR ENERGY↗
DOE OSTI2024

In situ energetics modulation enables high-efficiency and stable inverted perovskite solar cells

In contrast to conventional (n-i-p) perovskite solar cells (PSCs), inverted (p-i-n) PSCs offer enhanced stability and integrability with tandem solar cell architectures, which have garnered increasing interest. However, p-i-n cells suffer from energy level misalignment with transport layers, imbalanced transport of photo-generated electrons and holes, and significant defects with the perovskite films. Here we introduce tris(2,4,6-trimethyl-3-(pyridin-3-yl)phenyl)borane (3TPYMB), a nonionic n-type molecule that, through hydrogen bonding and Lewis acid-base reactions with perovskite surfaces or grain boundaries, enables in situ modulation of perovskite energetics, effectively mitigating the key challenges of p-i-n PSCs. The p-i-n PSCs incorporating 3TPYMB achieve a certified quasi-steady-state power conversion efficiency of 24.55 +- 0.33%, with a reverse scan efficiency of 25.58%. Finally, they also exhibit exceptional stability, with unencapsulated devices retaining 97.8% of their initial efficiency after 1,800 h of continuous operation at maximum power point under N 2 atmosphere, 1 sun illumination and 60 °C conditions.

14 SOLAR ENERGY↗
DOE OSTI2025

Predicting Trends in VOC Through Rapid, Multimodal Characterization of State-of-the-Art p-i-n Perovskite Devices

Perovskite photovoltaic technologies are approaching commercial deployment, yet single junction and tandem architectures both still have significant room to improve power conversion efficiency and stability. The ability to perform rapid screening of material quality after altering processing conditions is critical to accelerating the optimization and commercialization of perovskite-based technologies. Currently, researchers utilize a wide range of stand-alone metrology tools to isolate sources of power loss throughout a device stack, which can be slow and labor intensive. Here, we demonstrate the use of a multimodal metrology approach to rapidly determine the maximum achievable and predicted open circuit voltages of >100 perovskite devices during fabrication. Acquisition of these different data is facilitated by combining them into a single integrated measurement platform. We show that these data and automated analysis can be used to rapidly understand and ultimately predict quantitative trends in open circuit voltages of state-of-the-art device architectures. The data and automated analysis workflow presented provides a reliable approach to quickly identify absorber and charge transport layer combinations that can lead to improved open circuit voltages.

14 SOLAR ENERGY↗
DOE OSTI2023

Metal-semiconductor-metal structured p-i-n GaN/AlGaN ultrafast detectors for deep-UV photodetection

We report the productive outcome of the design, fabrication, and testing of a new class of GaN/AlGaN-based ultrafast, sensitive photodiodes for deep-UV solar blind photodetection. Pt was employed as the interdigitated metal electrode to establish that while a Schottky contact was formed at the metal/semiconductor heterojunction, it was the quantum wells in the p-i-n vertical structure that produced the diode characteristics of the detectors. The metal–semiconductor–metal design retained its ultrafast property as expected in the p-i-n structure because the spacing between the interdigitated fingers was asymmetrically implemented to optimize the photogenerated carriers’ transit time from the quantum well to the external circuitry. Also, the vertical p-i-n structure provided its renowned efficient photocarrier generation, which was significantly enhanced by the delta quantum well architecture of the vertical epitaxial structure. The active area of the device was 300 μm × 300 μm with 5-μm finger width, and asymmetric electrode spacing of 2 μm, 3 μm, and 5 μm. Here, the best device had peak responsivity of 3.5 A/W under 262-nm illumination with full width half maximum of 337.2-ps and 37.5-ps rise times when biased with 20 V.

efficient↗
DOE OSTI2020

All-Epitaxial Integration of Long-Wavelength Infrared Plasmonic Materials and Detectors for Enhanced Responsivity

Here, infrared detectors using monolithically integrated doped semiconductor “designer metals” are proposed and experimentally demonstrated. We leverage the “designer metal” groundplanes to form resonant cavities with enhanced absorption tuned across the long-wave infrared (LWIR). Detectors are designed with two target absorption enhancement wavelengths: 8 and 10 μm. The core of our detectors are quantum-engineered LWIR type-II superlattice p-i-n detectors with total thicknesses of only 1.42 and 1.80 μm for the 8 and 10 μm absorption enhancement devices, respectively. Our 8 and 10 μm structures show peak external quantum efficiencies of 45 and 27%, which are 4.5× and 2.7× enhanced, respectively, compared to control structures. We demonstrate the clear advantages of this detector architecture, both in terms of ease of growth/fabrication and enhanced device performance. The proposed architecture is absorber- and device-structure agnostic, much thinner than state-of-the-art LWIR T2SLs, and offers the opportunity for the integration of low dark current LWIR detector architectures for significant enhancement of IR detectivity.

42 ENGINEERING↗
DOE OSTI2023

Improving Stability of Triple-Cation Perovskite Solar Cells under High-Temperature Operation

Metal halide perovskite photovoltaic performance required for commercial technology encompasses both efficiency and stability. Advances in both these parameters have recently been reported; however, these strategies are often difficult to directly compare due to differences in perovskite composition, device architecture, fabrication methods, and accelerated stressors applied in stability tests. In particular, it is found that there is a distinct lack of elevated temperature, operational (light and bias) stability data. Furthermore, significant testing is required to understand the interactions when combinations are used (e.g., additives used with posttreatments). Herein, individual and combined additive, posttreatment, and contact layer strategies from recent literature reports under standardized operational stability tests of p-i-n CsMAFA perovskites at 70 degrees C are evaluated. Through analysis of over 1000 devices, it is concluded that the hole-transport layer (HTL) is the most significant component impacting elevated temperature operational stability. This analysis motivates future development of high-performance HTLs.

14 SOLAR ENERGY↗
DOE OSTI2021

Trap-Assisted Dopant Compensation Prevents Shunting in poly-Si Passivating Interdigitated Back Contact Silicon Solar Cells

Interdigitated back contact (IBC) solar cells achieve the highest efficiencies of single-junction architectures, but complicated patterning of the rear fingers and spreading of dopants during processing inhibit their mainstream adoption due to concerns of shunting between the IBC fingers. One method of simplifying patterning at the rear is by using contact masks combined with plasma-enhanced chemical vapor deposition (PECVD) or ion implantation. However, the intrinsic isolation region becomes contaminated during high-temperature annealing by lateral diffusion of dopants and during masked PECVD by spreading of dopant radicals through region between the mask and the substrate. Despite this contamination, we show through scanning spreading resistance microscopy and Kelvin probe force microscopy that a ~20 µm wide compensating region exists with high enough resistivity to prevent shunting. We model this p-i-n poly-Si system using two simulation models: a simple resistor model considering only the capture of charge carriers by trap defects in poly-Si to reduce the conductivity, and a more refined 1-dimensional finite element model using Poisson’s equation, drift-diffusion equations, and recombination of carriers. Using this model, we show that high defect density significantly decreases the current across the region between the p- and n-type fingers, preventing shunting.

atom probe↗
DOE OSTI2026

Improving perovskite solar module stability by understanding and mitigating scribe-induced chemo-thermomechanical degradation

Recognizing the correlation between the design of perovskite solar module (PSM) and their degradation mechanisms under environmental stressors helps to enable their long- term reliability. This work reports on the impact of the hole-transport layer (HTL) on thermal cyclability and degradation mechanisms of p-i-n PSMs by comparing 3 HTLs: NiO x , MeO-2PACz (a self-assembled monolayer), and a bilayer HTL of MeO-2PACz on NiO x . We observe surprising thermal cyclability from a performance standpoint despite generating clear degradation products. We find that without a fully dense HTL, seemingly insignificant moisture/oxygen ingress through the edge of the PSMs can lead to rapid destabilization of the metal halide perovskite (MHP) layer due to reactions between MHP degradation byproducts and the indium-tin oxide layer. We also show that illumination-induced cation phase segregation is dependent on the presence of an inactive area (regions of the substrate uncovered by the top electrode). As such, we find that a dense interface between the MHP and ITO is necessary for chemically robust PSMs and highlight criteria for testing field-relevant configurations in lab-scale architectures.

14 SOLAR ENERGY↗
DOE OSTI2024

Perovskite Grown in Gallium Nitride Nanowire Matrix for Stable and High‐Efficiency X‐Ray Detection

High-quality quasi-2D perovskites in a GaN nano-wire matrix are grown to build a 3D hetero-structure for high-performance X-ray sensing. In the 3D hetero-structure, GaN nano-wire matrix serves as an n-type charge collector that can rapidly extract carriers through the bulk film of the perovskite layer. Together with a p-type top electrode, a p–i–n diode with the 3D hetero-structure is built, that exhibits a rectified current–voltage characteristic. After analyzing the interface energy alignment, it is found that the fermi levels of the perovskite and GaN are aligned in the dark, and a quasi-fermi level splits upon illumination, introducing a built-in electrical field at the interface. As a result, strong photo-induced current is observed from the diode without an external field. Finally, the 3D diode for X-ray detection demonstration is used, revealing a sensitivity of 308.9 µC Gy air -1 cm -2 at an exceptionally low applied field of 0.125 V µm -1 . The X-ray-induced signal from the 3D diode is stable after 155 cycles of X-ray irradiation under a constant electric field. This demonstration informs a new 3D architecture for high-performance X-ray sensing, and it shows that GaN is a robust n-type interface for perovskite optoelectronic devices.

36 MATERIALS SCIENCE↗