SEARCH · Search NASA
Results for “panelized”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Study of Two Dimensional Panel Flutter and Panel Divergence in Subsonic Flow (III) - Experimental Studies of Two Dimensional and Three Dimensional Panels in Low Speed Wind Tunnel
Two-dimensional panel flutter and panel divergence in subsonic flow - wind tunnel testing of two and three-dimensional panels
Experimental Studies of Flutter of Buckled Rectangular Panels at Mach Numbers from 1.2 to 3.0 Including Effects of Pressure Differential and of Panel Width-Length Ratio
Experimental panel flutter data have been obtained at Mach numbers from 1.2 to 3.0 for buckled rectangular panels and the effect of a pressure differential has been determined. Increasing the pressure differential was effective in eliminating flutter on most of the panels tested. The effects of the variables in the panel flutter parameter ((square root of m(exp 2) -1) * (E/q))(exp 1/3) t/l (where M is the Mach number, q is the dynamic pressure, E is Young's modulus, and t and l are the panel thickness and length, respectively) were investigated for buckled panels clamped on the front and rear edges and a critical value of this parameter of 0.44 is indicated at zero pressure differential when the panel width-length ratio is 0.69. An estimated flutter boundary is presented for buckled panels clamped on four edges, with width-length ratios of 0.21 to 4.0. This boundary shows that the panel width is more significant than the panel length when the ratio of width to length is less than approximately 0.5. Panels clamped on four edges and buckled in two half waves in the direction of flow were found to be particularly susceptible to flutter. The results of limited tests on panels with applied damping, curvature, and lengthwise stiffeners are also presented and discussed.
The effect of oblique angle of sound incidence, realistic edge conditions, curvature and in-plane panel stresses on the noise reduction characteristics of general aviation type panels
Experiments and a theoretical analysis were conducted to predict the noise reduction of inclined and curved panels. These predictions are compared to the experimental results with reasonable agreement between theory and experiment for panels under an oblique angle of sound incidence. Theoretical as well as experimental results indicate a big increase in noise reduction when a flat test panel is curved. Further curving the panel slightly decreases the noise reduction. Riveted flat panels are shown to give a higher noise reduction in the stiffness-controlled frequency region, while bonded panels are superior in this region when the test panel is curved. Experimentally measured noise reduction characteristics of flat aluminum panels with uniaxial in-plane stresses are presented and discussed. These test results indicate an important improvement in the noise reduction of these panels in the frequency range below the fundamental panel/cavity frequency.
Investigation of forming curved ablative panels from flat panels for space shuttle
The purpose of this study was to determine the feasibility of reforming flat ablative panels to a curved configuration. The study indicated that if the panels could be shaped to a radius of 2.54 m (100 in.) then 88.7% of the surface area of the orbiter could be covered, and that if they could be shaped to a radius of 3.81 m (150 in.) then 77.2% of the surface could be covered. Two basic approaches were followed to determine the best method for forming the flat panels to a curved shape. The first was to determine if partially cured panels could be formed, allowing the forming heat cycle to complete the curing of the ablator. The second method was to form fully cured flat panels into the desired curvature through a secondary heat cycle. Measurements made on the panels during storage indicated that they continued to straighten out over time. This was attributed to residual stresses locked into the panels that had not been fully relaxed by the heat cycle.
Vibration Response Predictions for Heavy Panel Mounted Components from Panel Acreage Environment Specifications
The development of new launch vehicles in the Aerospace industry often relies on response measurements taken from previously developed vehicles during various stages of liftoff and ascent, and from wind tunnel models. These measurements include sound pressure levels, dynamic pressures in turbulent boundary layers and accelerations. Rigorous statistical scaling methods are applied to the data to derive new environments and estimate the performance of new skin panel structures. Scaling methods have proven to be reliable, particularly for designs similar to the vehicles used as the basis for scaling, and especially in regions of smooth acreage without exterior protuberances or heavy components mounted to the panel. To account for response attenuation of a panel-mounted component due to its apparent mass at higher frequencies, the vibroacoustics engineer often reduces the acreage vibration according to a weight ratio first suggested by Barrett. The accuracy of the reduction is reduced with increased weight of the panel-mounted component, and does not account for low-frequency amplification of the component/panel response as a system. A method is proposed that combines acreage vibration from scaling methods with finite element analysis to account for the frequency-dependent dynamics of heavy panel-mounted components. Since the acreage and mass-loaded skins respond to the same dynamic input pressure, such pressure may be eliminated in favor of a frequency-dependent scaling function applied to the acreage vibration to predict the mass-loaded panel response. The scaling function replaces the Barrett weight ratio, and contains all of the dynamic character of the loaded and unloaded skin panels. The solution simplifies for spatially uncorrelated and fully correlated input pressures. Since the prediction uses finite element models of the loaded and unloaded skins, a rich suite of response data are available to the design engineer, including interface forces, stress and strain, as well as acceleration and displacement. An extension of the method is also developed to incorporate the effect of a local protuberance near a heavy component. Acreage environments from traditional scaling methods with and without protuberance effects serve as the basis for the extension. Authors:
Supersonic Panel Flutter Test Results for Flat Fiber-Glass Sandwich Panels with Foamed Cores
Flutter tests have been made on flat panels having a 1/4 inch-thick plastic-foam core covered with thin fiber-glass laminates. The testing was done in the Langley Unitary Plan wind tunnel at Mach numbers from 1.76 t o 2.87. The flutter boundary for these panels was found to be near the flutter boundary of thin metal panels when compared on the basis of an equivalent panel stiffness. The results also demonstrated that the depth of the cavity behind the panel has a pronounced influence on flutter. Changing the cavity depth from 1 1/2 inches to 1/2 inch reduced the dynamic pressure at start of flutter by 40 percent. No flutter was obtained when the spacers on the back of the panel were against the bottom of the cavity.
Panel Resource Management (PRM) Implementation and Effects within Safety Review Panel Settings and Dynamics
While technical training and advanced degree's assure proficiency at specific tasks within engineering disciplines, they fail to address the potential for communication breakdown and decision making errors familiar to multicultural environments where language barriers, intimidating personalities and interdisciplinary misconceptions exist. In an effort to minimize these pitfalls to effective panel review, NASA's lead safety engineers to the ISS Safety Review Panel (SRP), and Payload Safety Review Panel (PSRP) initiated training with their engineers, in conjunction with the panel chairs, and began a Panel Resource Management (PRM) program. The intent of this program focuses on the ability to reduce the barriers inhibiting effective participation from all panel attendees by bolstering participants confidence levels through increased communication skills, situational awareness, debriefing, and a better technical understanding of requirements and systems.
Effect of boundary conditions and panel geometry on the response of laminated panels subjected to transverse pressure loads
The behavior of thin laminated flat and curved panels subjected to transverse pressure and inplane loads is considered. The effects of panel geometry, boundary conditions and laminate stacking sequence on the response of panels subjected to transverse pressure loads up to 12.4 N/sq cm is presented. The response of thin laminated panels is evaluated analytically and selected results are compared with test data. A parametric study of the deformation and strain responses of panels with radius of curvature ranging from 20 to 305 cm is presented. The combination of inplane tensile and pressure loads is also considered.
Packaging, deployment, and panel design concepts for a truss-stiffened 7-panel precision deployable reflector with feed boom
A concept is presented for achieving a remotely deployable truss-stiffened reflector consisting of seven integrated sandwich panels that form the reflective surface, and an integrated feed boom. The concept has potential for meeting aperture size and surface precision requirements for some high-frequency microwave remote sensing applications. The packaged reflector/feed boom configuration is a self-contained unit that can be conveniently attached to a spacecraft bus. The package has a cylindrical envelope compatible with typical launch vehicle shrouds. Dynamic behavior of a deployed configuration having a 216-inch focal length and consisting of 80-inch-diameter, two-inch-thick panels is examined through finite-element analysis. Results show that the feed boom and spacecraft bus can have a large impact on the fundamental frequency of the deployed configuration. Two candidate rib-stiffened sandwich panel configurations for this application are described, and analytical results for panel mass and stiffness are presented. Results show that the addition of only a few rib stiffeners, if sufficiently deep, can efficiently improve sandwich panel stiffness.
Fabrication of Lower Section and Upper Forward Bulkhead Panels of the Multi-Bay Box and Panel Preparation
NASA and the Boeing Co. have been working together under the Environmentally Responsible Aviation Project to develop stitched unitized structure for reduced weight, reduced fuel burn and reduced pollutants in the next generation of commercial aircraft. The structural concept being evaluated is PRSEUS (Pultruded Rod Stitched Efficient Unitized Structure). In the PRSEUS concept, dry carbon fabric, pultruded carbon rods, and foam are stitched together into large preforms. Then these preforms are infused with an epoxy resin into large panels in an out-of-autoclave process. These panels have stiffeners in the length-wise and width-wise directions but contain no fasteners because all stiffeners are stitched to the panel skin. This document contains a description of the fabrication of panels for use in the 30-foot-long Multi-Bay Box test article to be evaluated at NASA LaRC. The document also describes a panel which explores new PRSEUS concepts for applications beyond the Multi-Bay Box.
Optical monitor panel provides flexible test panel configurations
Optical monitor panel projects a chosen panel configuration upon a translucent screen by using a master projector and appropriate slide to project panel board nomenclature and a series of smaller individual projectors to superimpose monitor indicators upon the projected panel board.
A general panel sizing computer code and its application to composite structural panels
A computer code for obtaining the dimensions of optimum (least mass) stiffened composite structural panels is described. The procedure, which is based on nonlinear mathematical programming and a rigorous buckling analysis, is applicable to general cross sections under general loading conditions causing buckling. A simplified method of accounting for bow-type imperfections is also included. Design studies in the form of structural efficiency charts for axial compression loading are made with the code for blade and hat stiffened panels. The effects on panel mass of imperfections, material strength limitations, and panel stiffness requirements are also examined. Comparisons with previously published experimental data show that accounting for imperfections improves correlation between theory and experiment.
Study of noise reduction characteristics of composite fiber-reinforced panels, interior panel configurations, and the application of the tuned damper concept
The application of fiber reinforced composite materials, such as graphite epoxy and Kevlar, for secondary or primary structures developing in the commercial airplane industry was investigated. A composite panel program was initiated to study the effects of some of the parameters that affect noise reduction of these panels. The fiber materials and the ply orientation were chosen to be variables in the test program. It was found that increasing the damping characteristics of a structural panel will reduce the vibration amplitudes at resonant frequencies with attendant reductions in sound reduction. Test results for a dynamic absorber, a tuned damper, are presented and evaluated.
The Payload Advisory Panel and the Data and Information System Advisory Panel of the Investigators Working Group of the Earth Observing System: A joint report
The Payload Advisory Panel of the Investigators Working Group (IWG) for the Earth Observing System (EOS) met 4 to 6 October 1993 in Herndon, Virginia. The Panel, originally composed of the Interdisciplinary Science Principal Investigators, was expanded to include all Principal Investigators and as such is now the IWG itself. The meeting also addressed directly a report from the EOS Data and Information System (EOSDIS) Advisory Panel. The meeting focused on payload issues in the years 2000 to 2005; however, some subjects in the nearer-term, most significantly EOSDIS, were considered. The overarching theme of convergence in Earth observations set a backdrop for the entire meeting. Other themes included: atmospheric chemistry; remote sensing of the global cycles of energy, water, and carbon in EOS; ocean and land-ice altimetry; and the EOSDIS. The Totol Solar Irradiance Monitoring Report and results from the Accelerated Canopy Chemistry Program are included as appendices.
EXPERIMENTAL PANEL FLUTTER RESULTS FOR SOME FLAT AND CURVED TITANIUM SKIN PANELS AT SUPERSONIC SPEEDS
Panel flutter results for flat and curved titanium skin panels at supersonic speed
The Study of Stability of Compression-loaded Multispan Composite Panel Upon Failure of elements Binding it to Panel Supports
The present document is a final technical report under the NCC-1-233 research program (dated September 15, 1998; see Appendix 5) carried out within co-operation between United States'NASA Langley RC and Russia's Goskomoboronprom in aeronautics, and continues similar programs, NCCW-73, NCC-1-233 and NCCW 1-233 accomplished in 1996, 1997, and 1998, respectively. The report provides results of "The study of stability of compression-loaded multispan composite panels upon failure of elements binding it to panel supports"; these comply with requirements established at TsAGI on 24 March 1998 and at NASA on 15 September 1998.
The Study of Stability of Compression-Loaded Multispan Composite Panel Upon Failure of Elements Binding it to Panel Supports
The present document is a final technical report carried out within co-operation between United States'NASA Langley RC and Russia's Goskomoboronprom in aeronautics, and continues similar programs, accomplished in 1996, 1997, and 1998, respectively). The report provides results of "The study of stability of compression-loaded multispan composite panels upon failure of elements binding it to panel supports"; these comply with requirements established at TsAGI on 24 March 1998 and at NASA on 15 September 1998.