Search NASA⌕ Search

SEARCH · Search NASA

Results for “parametric optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Dynamic Modeling of a Kaplan Hydroturbine Using Optimal Parametric Tuning and Real Plant Operational Data

To address grid variability caused by renewable energy integration and to maintain grid reliability and resilience, hydropower must quickly adjust its power generation over short time periods. This changing energy generation landscape requires advance technology integration and adaptive parameter optimization for hydropower systems via digital twin effort. However, this is difficult owing to the lack of characterization and modeling for the nonlinear nature of hydroturbines. To solve this issue, this paper first formulates a six-coefficient Kaplan hydroturbine model and then proposes a parametric optimization tuning framework based on the Nelder–Mead algorithm for adaptive dynamic learning of the six-coefficients so as to build models that describe the turbine. To assess the performance of the proposed optimal parametric tuning technique, operational data from a real-world Kaplan hydroturbine unit are collected and used to model the relationship between the gate opening and the generated power production. The findings show that the proposed technique can effectively and adaptively learn the unknown dynamics of the Kaplan hydroturbine while optimally tune the unknown coefficients to match the generated power output from the real hydroturbine unit with an inaccuracy of less than 5%. The method can be used to provides optimal tuning of parameters critical for controller design, operational optimization and daily maintenance for hydroturbines in general.

13 HYDRO ENERGY↗
DOE OSTI2026

Parametric optimization of PCM-enhanced underground thermal energy storage for buildings in moderate cold climates

This study presents a novel underground thermal energy storage (UTES) system designed for space heating in buildings located in moderate cold climates. The proposed UTES features a borehole with a depth of 25 ft. (7.62 m) and a diameter of 3 ft. (0.91 m), containing two helical pipe loops-one for discharge fluid and another for recharge fluid-and a thermally enhanced phase change material (PCM) layer that provides high energy storage capacity. The system requires daily thermal recharging using a low-grade heat source for a few hours and delivers continuous heating at a nearly constant discharge rate without significant performance degradation over a 24-h period. This study demonstrates that the optimized UTES, when recharged with hot fluid at an inlet temperature of 40 degrees C for 6 h daily, can provide a continuous heat discharge rate of approximately 2.9 kW for 24 h or 3.4 kW if operated under a shorter discharge period of 15 h (17:00-08:00). With a round-trip efficiency of 72-97%, the proposed UTES offers an efficient and reliable solution for short- and long-duration thermal energy storage technology, making it a promising technology for cold climates.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Parametric optimization of the liquid sampling-atmospheric pressure glow discharge ionization source coupled to an Orbitrap mass spectrometer for neodymium isotope ratio determinations

Isotope ratio determinations are a valuable tool in several application areas. In nuclear forensics, the isotope ratios of uranium and plutonium are commonly used as a signature for the nuclear material's provenance and processing history. However, signatures from other coexisting elements, such as neodymium and samarium, can offer additional insights. Here, the liquid sampling-atmospheric pressure glow discharge (LS-APGD) ionization source coupled to an Orbitrap mass spectrometer (MS) has demonstrated its utility for actinide measurements. This instrumental platform can leverage the high resolution offered by the Orbitrap MS to overcome potential isobaric interferences, such as 144 Nd- 144 Sm, 148 Nd- 148 Sm, and 150 Nd- 150 Sm pairs. The work presented herein demonstrates the rapid, accurate, and precise determination of the isotope ratios for neodymium using the LS-APGD/Orbitrap MS. Both the LS-APGD and Orbitrap MS parameters were optimized systematically, with NdO + found to be the most abundant, most reduced species after applying the optimal collision-induced dissociation modalities. A limit of detection of 3 pg of 142 Nd was achieved when data was acquired and processed using the FTMS Booster, an external data acquisition and processing system offered by Spectroswiss. Excellent accuracy of better than 99 % and precision of <1 % RSD were achieved when a solution of the well-characterized neodymium standard (JNdi-1 standard) was analyzed under the optimized condition, indicating the LS-APGD/Orbitrap's great potential for isotope ratio analysis of Nd and other REEs for diverse applications.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Parametric Optimization of Nanostructured Alumina Forming Austenitic Alloys

Alumina-forming austenitic (AFA) alloys provide excellent oxidation resistance through the formation of a stable alumina scale, but their relatively high Ni content might limit application in core structural components because of helium generation and swelling under irradiation. Increasing the density of nanoscale features in the microstructure is a promising route to improve sink strength and mitigate these effects. Conventional oxide dispersion–strengthened (ODS) steels achieve this through mechanical alloying (MA), but the approach is costly and difficult to scale. In this milestone, additive manufacturing was applied as an alternative pathway to fabricate nanostructured AFA (NAFA) alloys with dual precipitation of oxides and nitrides enabled by reactive atmosphere processing. In FY25, two compositions, NAFA-1 (AFA-05) and NAFA-2, were produced and compared. Both alloys achieved densities above 99% of theoretical values, but NAFA-2 exhibited microcracking associated with Nb-rich intermetallic formation, indicating the need for further chemistry optimization. Nitrogen and oxygen uptake was confirmed on selected builds, demonstrating the intended dual-precipitate dispersion. Mechanical testing showed that AM-processed NAFA alloys exceed conventionally produced ODS steels in high-temperature tensile strength and fracture toughness. Preliminary Cu ion irradiation results further suggest improved resistance compared to wrought austenitic alloys. While the current alloys are promising for their compatibility in high-temperature air or liquid Pb environments, modifications to composition will be required for long-term operation in high-temperature impure sodium systems. Future work will focus on refining alloy chemistry to suppress laser powder bed fusion–induced cracking and scaling production to reactor-relevant dimensions using directed energy deposition as a pathway toward net-shape cladding fabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Control optimization for parametric Hamiltonians by pulse reconstruction

Optimal control techniques provide a means to tailor the control pulses required to generate customized quantum gates, which helps to improve the resilience of quantum simulations to gate errors and device noise. However, the significant amount of (classical) computation required to generate customized gates can quickly undermine the effectiveness of this approach, especially when pulse optimization needs to be iterated. We propose a method to reduce the computational time required to generate the control pulse for a Hamiltonian that is parametrically dependent on a time-varying quantity. We use simple interpolation schemes to accurately reconstruct the control pulses from a set of pulses obtained in advance for a discrete set of predetermined parameter values. We obtain a reconstruction with very high fidelity and a significant reduction in computational effort. We report the results of the application of the proposed method to device-level quantum simulations of the unitary (real) time evolution of two interacting neutrons based on superconducting qubits.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Multiphysics Design Optimization and Additive Manufacturing of Nuclear Components (Final CRADA Report - Executive Summary)

Westinghouse Electric Company (WEC) actively participated in the advancement of the nuclear fuel and reactor design space and requested the help of Oak Ridge National Laboratory (ORNL) in the creation of a new design tool set. This report details the creation of a collection of software tool sets that are linked together to collectively assist WEC design engineers in developing novel ideas outside the normal scope of traditional nuclear fuel and reactor design formulas. Specifically, Siemens HEEDS, a design space exploration and parametric optimization software, monitored and changed parameters in a collection of softwares to meet the team’s objective. The HEEDS parametric optimization method, SHERPA, was developed to control the Siemens NX CAD platform to adjust the native CAD of a hexahedral spacer grid. This new geometry can be used to execute a topological design optimization by the NX Topology software add-in. The resulting geometry is additively manufacturable. This topological optimization occurred twice—once on the spacer grid’s spring, and once on the dimple geometry. These new geometries were imported by Siemens’ STAR-CCM+, a multiphysics structural and fluid dynamic computational solver in which the spring geometry is deflected to match the rod insertion configuration. Along with the dimple geometry, this new deflected spring was used to complete a hydraulic assessment of a single-unit cell comprising one rod, one spring, and two dimples. The HEEDS SHERPA algorithm ranks the design based on the final mass of the unit cell and the hydraulic pressure drop performance. The ORNL team demonstrated the ability to use this software and provided engineering judgement to apply modern aerospace aerodynamic design. The effort has been focused on thinking outside the conventional design space and redesigning a spacer grid to perform beyond the WEC set objectives. Furthermore, the ORNL team also demonstrated that the HEEDS optimization routine can independently develop a design that meets the WEC design goals. Although these designs were at a low technology readiness level, their demonstration confirmed the team’s capability to create novel advanced nuclear concepts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Learning Constrained Parametric Differentiable Predictive Control Policies With Guarantees

We present differentiable predictive control (DPC), a method for offline learning of constrained neural control policies for nonlinear dynamical systems with performance guarantees. We show that the sensitivities of the parametric optimal control problem can be used to obtain direct policy gradients. Specifically, we employ automatic differentiation (AD) to efficiently compute the sensitivities of the model predictive control (MPC) objective function and constraints penalties. To guarantee safety upon deployment, we derive probabilistic guarantees on closed-loop stability and constraint satisfaction based on indicator functions and Hoeffding’s inequality. We empirically demonstrate that the proposed method can learn neural control policies for various parametric optimal control tasks. In particular, we show that the proposed DPC method can stabilize systems with unstable dynamics, track time-varying references, and satisfy nonlinear state and input constraints. Our DPC method has practical time savings compared to alternative approaches for fast and memory-efficient controller design. Specifically, DPC does not depend on a supervisory controller as opposed to approximate MPC based on imitation learning. We demonstrate that, without losing performance, DPC is scalable with greatly reduced demands on memory and computation compared to implicit and explicit MPC while being more sample efficient than model-free reinforcement learning (RL) algorithms.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

DED Additively Manufactured HEAs Optimized via Parametric Study of Functionally Graded Materials

Complex concentrated alloys (CCAs) are a system of alloys composition of nearly equiatomic elements, creating a state of high configurational entropy in the material. These alloys are of interest for various industrial applications due to their high strength and hardness, wide operational temperature range, creep and diffusion resistance, and radiation resistance. In the current work CoCrFeNi-base CCAs are synthesize by combining three commonly industrial alloys: IN718, SS316L, and 70Co30Cr (commercially known as Stellite 21), in-situ utilizing directed energy deposition (DED) additive manufacturing (AM). One bulk specimen is fabricated with a 1:1:1 ratio of IN718, SS316L, and 70Co30Cr where IN718 is a source of nickel and chrome, SS316 is a source of iron and chrome, and 70Co30Cr is a source of cobalt and supplemental chrome. Additionally, a functionally graded material (FGM) of the identified CCA system from SS316 was fabricated with 10 layers, where the initial five layers are the base material of SS316L and graded by steps of 20% to transition to the CCA system. Overall build quality, microstructure, compositional distribution, phases analysis, and microhardness were studied by laser optical microscopy, scanning election microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD), and Vickers microhardness techniques. Overall build quality showed a successful bulk build with acceptable density, however unmelted particles are observed in the as-built alloy. Compositional results show that the system meets the Boltzmann’s hypothesis definition of an HEA, and that an FCC CCA was produced with increased hardness, small grain size, and superior hardness properties to the SS316L substrate. While initial XRD results show predominately FCC structure, EDS analysis of interdendritic regions show the existence of Laves phases in the material. The fabrication of an FGM CCA allowed for potential screening of additional alloy mixes which may be of interest to explore in future research, and the resulting composition is compared to predicted values. This novel method of CCA fabrication results in substantial cost savings of these CCA systems over traditional methods.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Optimization-Inspired Pin-Fin Array for Supercritical Carbon Dioxide Recuperator

Additively manufactured heat exchangers are one possible route to cost-effective sCO 2 power cycles. In this paper, experimental results are obtained for two helical pin fin tubes that were designed following parametric optimization of the fin array. Neither the numerical optimization nor the experimental testing have been previously reported in the literature. The two tube designs were, (1) the optimization inspired design, and (2) the optimization-inspired design with a fin diameter increased by a factor of 2. To characterize the print, the designs were scanned using X-ray computed tomography to measure feature sizes and heat transfer area. The optimization was conducted in a commercial, computational fluid dynamics code. The code solved the Reynolds Averaged Navier-Stokes (RANS) and energy equations with turbulence closure provided by the shear stress transport (SST) k-ω model. In the experiments, the Nusselt number augmentation was measured using the Wilson plot technique and the friction factor was determined with mass flow and pressure drop measurements. The experimental testing indicated that the optimization-inspired design had a friction factor that was four times less than the baseline tube design at equal Nusselt number. Additionally, the optimization-inspired design had a 14% improvement in Nusselt number, at equal friction factor, relative to the best performing computational fluid dynamics (CFD) trial points. Tube design (2), with the larger diameter pin fins, had similar performance, within experimental error, as the tube with the smaller diameter pin fins (1). Both tubes achieved overall fin array efficiencies near 1. A performance factor, V/V 0 , equal to the volume of the enhanced heat exchanger divided by the volume of the baseline (no-fins) heat exchanger, is recommended to quantify internal cooling performance. In conclusion, the experimental shell and tube heat exchanger, using the additively manufactured tube, is competitive with printed circuit heat exchangers in its pressure drop class and could be further improved by optimizing a shell-and-tube heat exchanger utilizing this heat transfer enhancement feature.

42 ENGINEERING↗
DOE OSTI2022

Learning high-dimensional parametric maps via reduced basis adaptive residual networks

We propose a scalable framework for the learning of high-dimensional parametric maps via adaptively constructed residual network (ResNet) maps between reduced bases of the inputs and outputs. When just few training data are available, it is beneficial to have a compact parametrization in order to ameliorate the ill-posedness of the neural network training problem. By linearly restricting high-dimensional maps to informed reduced bases of the inputs, one can compress high-dimensional maps in a constructive way that can be used to detect appropriate basis ranks, equipped with rigorous error estimates. A scalable neural network learning framework is thus to learn the nonlinear compressed reduced basis mapping. Unlike the reduced basis construction, however, neural network constructions are not guaranteed to reduce errors by adding representation power, making it difficult to achieve good practical performance. Inspired by recent approximation theory that connects ResNets to sequential minimizing flows, we present an adaptive ResNet construction algorithm. This algorithm allows for depth-wise enrichment of the neural network approximation, in a manner that can achieve good practical performance by first training a shallow network and then adapting. We prove universal approximation of the associated neural network class for $L^2_v$ functions on compact sets. Our overall framework allows for constructive means to detect appropriate breadth and depth, and related compact parametrizations of neural networks, significantly reducing the need for architectural hyperparameter tuning. Numerical experiments for parametric PDE problems and a 3D CFD wing design optimization parametric map demonstrate that the proposed methodology can achieve remarkably high accuracy for limited training data, and outperformed other neural network strategies we compared against.

42 ENGINEERING↗
DOE OSTI2023

Temperature dependence of magnetic anisotropy and magnetoelasticity from classical spin-lattice calculations

Here we present a classical molecular-spin dynamics (MSD) methodology that enables accurate computations of the temperature dependence of the magnetocrystalline anisotropy as well as magnetoelastic properties of magnetic materials. The nonmagnetic interactions are accounted for by a spectral neighbor analysis potential (SNAP) machine-learned interatomic potential, whereas the magnetoelastic contributions are accounted for using a combination of an extended Heisenberg Hamiltonian and a Néel pair interaction model, representing both the exchange interaction and spin-orbit-coupling effects, respectively. All magnetoelastic potential components are parameterized using a combination of first-principles and experimental data. Our framework is applied to the α phase of iron. Initial testing of our MSD model is done using a 0 K parametrization of the Néel interaction model. After this, we examine how individual Néel parameters impact the $B$ 1 and $B$ 2 magnetostrictive coefficients using a moment-independent δ sensitivity analysis. The results from this study are then used to initialize a genetic algorithm optimization which explores the Néel parameter phase space and tries to minimize the error in the B 1 and B 2 magnetostrictive coefficients in the range of 0–1200 K. Our results show that while both the 0 K and genetic algorithm optimized parametrization provide good experimental agreement for $B$ 1 and $B$ 2 , only the genetic algorithm optimized results can capture the second peak in the $B$ 1 magnetostrictive coefficient which occurs near approximately 800 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Ultra–high molecular weight polyethylene micro–ribbon fibers gel spun using orange terpenes

Toxic, hazardous petrochemical solvents are commonly used for industrial-scale ultra-high molecular weight polyethylene (UHMWPE) fiber production, but orange terpenes, a byproduct of orange fruit production, present a bio-derived, sustainable alternative. In this work, fine UHMWPE fibers were spun using orange terpenes as the spin solvent, hot-drawn at a draw ratio of 5:1, investigated for their morphology, microstructure, and thermal and mechanical properties. The resulting fibers exhibited a flat, micro-ribbon cross-section, which is highly desirable for achieving high fiber volume fractions in UHMWPE-fiber reinforced composites. After drawing, the fibers possessed 4× greater breaking tenacity than any previously published studies on UHMWPE fibers spun using orange terpenes with a tenacity of 8.6 cN/dtex and tensile modulus of 229.2 cN/dtex. Microstructural analysis via differential scanning calorimetry and X-ray diffraction revealed that the hot drawing process significantly increased molecular orientation, but crystallinity decreased due to crystallite melting during drawing. Therefore, the mechanical properties of these fibers may be significantly improved with optimization of the fiber drawing process. As a work, this work establishes the strong potential of orange terpenes as an environmentally-friendly alternative solvent for UHMWPE gel spinning and sets a foundation for future parametric optimization of the spinning and drawing of these fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Sequential Quadratic Programming Algorithm for Nonsmooth Problems with Upper- \({\boldsymbol{\mathcal{C}^2}}\) Objective

An optimization algorithm for nonsmooth nonconvex constrained optimization problems with upper- \({\boldsymbol{\mathcal{C}^2}}\) objective functions is proposed and analyzed. Upper- \({\boldsymbol{\mathcal{C}^2}}\) is a weakly concave property that exists in difference of convex (DC) functions and arises naturally in many applications, particularly certain classes of solutions to parametric optimization problems e.g., recourse of stochastic programming and projection onto closed sets. The algorithm can be viewed as an extension of sequential quadratic programming (SQP) to nonsmooth problems with upper- \({\boldsymbol{\mathcal{C}^2}}\) objectives or a simplified bundle method. It is globally convergent with bounded algorithm parameters that are updated with a trust-region criterion. The algorithm handles general smooth constraints through linearization and uses a line search to ensure progress. The potential inconsistencies from the linearization of the constraints are addressed through a penalty method. In conclusion, the capabilities of the algorithm are demonstrated by solving both simple upper- \({\boldsymbol{\mathcal{C}^2}}\) problems and a real-world optimal power flow problem used in current power grid industry practices.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Multi-objective parametrization of interatomic potentials for large deformation pathways and fracture of two-dimensional materials

Abstract This investigation presents a generally applicable framework for parameterizing interatomic potentials to accurately capture large deformation pathways. It incorporates a multi-objective genetic algorithm, training and screening property sets, and correlation and principal component analyses. The framework enables iterative definition of properties in the training and screening sets, guided by correlation relationships between properties, aiming to achieve optimal parametrizations for properties of interest. Specifically, the performance of increasingly complex potentials, Buckingham, Stillinger-Weber, Tersoff, and modified reactive empirical bond-order potentials are compared. Using MoSe 2 as a case study, we demonstrate good reproducibility of training/screening properties and superior transferability. For MoSe 2 , the best performance is achieved using the Tersoff potential, which is ascribed to its apparent higher flexibility embedded in its functional form. These results should facilitate the selection and parametrization of interatomic potentials for exploring mechanical and phononic properties of a large library of two-dimensional and bulk materials.

Zhang, Xu↗
DOE OSTI2024

Dissimilar Material Joining via Interlocking Metasurfaces

Background The integration of dissimilar materials poses a significant challenge in engineering, necessitating innovative solutions for robust and reliable joining. Interlocking metasurfaces (ILMs) are a new joining technology comprising arrays of autogenous features patterned across two surfaces that interlock to form robust structural joints. Objective Here, this study elucidates the factors influencing the tensile performance of ILM joints formed between dissimilar materials. Methods We employed parametric optimization to identify optimal unit cell geometries for maximal yield strength based on the hypothesis that the elastic tensile properties of the materials are the primary determinants of tensile performance. Experimental validation was performed by mechanically testing the theorized optimal ILM geometry and a range of ILM geometries to capture the overall behavior trends of joints between two additively manufactured polymers, VeroPureWhite (VW) and RGDA8430-DM (8430). Results Experimental validation of optimized designs revealed that additional factors, e.g. flexural strength and localized plasticity, also strongly influenced the tensile performance of T-slot ILMs joining dissimilar materials. The proposed optimal design remained the best performer. Conclusions This study demonstrates the viability of ILMs as a joining method for dissimilar materials. ILMs can join dissimilar materials with no loss in joint yield strength compared to joints composed solely of the weaker of the two constitutive materials. ILMs demonstrated their potential as a versatile and effective joining technology in diverse engineering applications.

Elbrecht, Benjamin James [Sandia National Laborato↗
DOE OSTI2023

Microwave-assisted co-gasification of mixed plastics and corn stover: A synergistic approach to produce clean hydrogen

Co-gasification of waste plastic and corn stover into hydrogen is an effective way of reducing hydrogen cost and carbon footprint. However, current gasification technologies are energy intensive and cannot accommodate flexible feedstock. Microwave gasification offers several advantages including higher H 2 yield and enhanced selectivity to syngas over tars. Herein this work presents parametric optimization study of microwave co-gasification of mixed plastics and corn stover for hydrogen-rich syngas. High hydrogen yields of 30.5 mmol H2 /g feed at 700 °C were obtained using a microwave reactor, as opposed to 0.9 mmolH 2 /g feed at 700-950 °C with conventional heating. Hydrogen yields are >98% of the theoretical extractable hydrogen from feedstock. Microwaves enhanced plastic and corn stover synergy and reduced tar yields. H-poor carbon formation resulting from the dehydrogenation of tar and coke, and light olefins decomposition, triggered by the external microwave electric fields, allowed further cracking of intermediate hydrocarbons to produce additional H 2 .

30 DIRECT ENERGY CONVERSION↗