Search NASA⌕ Search

SEARCH · Search NASA

Results for “penetration design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Mechanical Design and Configuration of Penetrations for the Europa Clipper Avionics Vault Structure

The main purpose of the Avionics Vault is to shield radiation sensitive electronics for the Europa Clipper Spacecraft. The vault is a box structure made out of aluminum panels. The panels are roughly 10 mm thick in order to shield the electronics from the orbital total ionizing radiation around Jupiter. The vault requires an electromagnetic interference (EMI) shielding effectiveness (SE) of at least 70 dB in order to mitigate EMI with the spacecraft radar receiver. Overall, the vault accommodates four main types of penetrations: receptacle connectors, pass-through cables, fluid lines, and vent holes. More than 150 cables penetrate the vault panels to connect to electronic boxes inside. Fluid pipes enter and exit the vault to transfer heat to the rest of the spacecraft. Vent holes provide a path for air to escape from the vault during launch. Several novel penetrations designs were created to meet EMI and radiation shielding requirements. Receptacle connectors interface to the vault panels using 1.3 mm thick Ta10W plates. Pass-through cables penetrate the vault using aluminum clamshells after being wrapped with Teflon cushion tape, Kapton tape, and copper tape. Vent hole penetrations consist of a copper mesh for EMI shielding and an aluminum radiation shield bracket to direct air out of the vault during launch. Fluid lines terminate at the vault wall using mechanical fittings that resemble a nut and bolt interface. In addition, most mechanical seams and penetrations utilize EMI gaskets to ensure proper EMI shielding. To reduce risk and confirm that the vault penetration designs were appropriate for EMI shielding, an EMI chamber at the Jet Propulsion Laboratory (JPL) was used to test a mock-up vault panel with multiple variations of all four main types of vault penetrations. This EMI SE test also incorporated different methods for bundling pass-through cables, and a comparison of flange mounted connectors versus jam nut connectors. A low noise preamplifier and a Rohde & Schwarz spectrum analyzer measured E-field levels transmitting through the mock-up vault panel. The results showed a shielding effectiveness of 77 dB for the mock-up vault panel, which exceeds the 70 dB target for Europa Clipper. Both the flange mounted connectors and jam nut connectors exhibited similar EMI SE results at the measured frequencies, and all variations of vault penetrations showed favorable EMI SE levels. Since the flight panels will be much larger and include many more penetrations, there will be testing of the flight vault to confirm its EMI SE is compliant with environmental requirements.

Giersch, Louis↗

Space station integrated wall design and penetration damage control

A methodology was developed to allow a designer to optimize the pressure wall, insulation, and meteoroid/debris shield system of a manned spacecraft for a given spacecraft configuration and threat environment. The threat environment consists of meteoroids and orbital debris, as specified for an arbitrary orbit and expected lifetime. An overall probability of no penetration is calculated, as well as contours of equal threat that take into account spacecraft geometry and orientation. Techniques, tools, and procedures for repairing an impacted and penetrated pressure wall were developed and tested. These techniques are applied from the spacecraft interior and account for the possibility of performing the repair in a vacuum. Hypervelocity impact testing was conducted to: (1) develop and refine appropriate penetration functions, and (2) determine the internal effects of a penetration on personnel and equipment.

Coronado, A. R.↗

Space station integrated wall design and penetration damage control

The analysis code BUMPER executes a numerical solution to the problem of calculating the probability of no penetration (PNP) of a spacecraft subject to man-made orbital debris or meteoroid impact. The codes were developed on a DEC VAX 11/780 computer that uses the Virtual Memory System (VMS) operating system, which is written in FORTRAN 77 with no VAX extensions. To help illustrate the steps involved, a single sample analysis is performed. The example used is the space station reference configuration. The finite element model (FEM) of this configuration is relatively complex but demonstrates many BUMPER features. The computer tools and guidelines are described for constructing a FEM for the space station under consideration. The methods used to analyze the sensitivity of PNP to variations in design, are described. Ways are suggested for developing contour plots of the sensitivity study data. Additional BUMPER analysis examples are provided, including FEMs, command inputs, and data outputs. The mathematical theory used as the basis for the code is described, and illustrates the data flow within the analysis.

Coronado, A. R.↗

Space station integrated wall design and penetration damage control. Task 3: Theoretical analysis of penetration mechanics

The efforts to provide a penetration code called PEN4 version 10 is documented for calculation of projectile and target states for the impact of 2024-T3 aluminum, R sub B 90 1018 steel projectiles and icy meteoroids onto 2024-T3 aluminum plates at impact velocities from 0 to 16 km/s. PEN4 determines whether a plate is perforated by calculating the state of fragmentation of projectile and first plate. Depth of penetration into the second to n sup th plate by fragments resulting from first plate perforation is determined by multiple cratering. The results from applications are given.

Bjorkman, M. D.↗

Space station integrated wall design and penetration damage control. Task 4: Impact detection/location system

A program to develop a methodology is documented for detecting and locating meteoroid and debris impacts and penetrations of a wall configuration currently specified for use on space station. Testing consisted of penetrating and non-penetrating hypervelocity impacts on single and dual plate test configurations, including a prototype 1.22 m x 2.44 m x 3.56 mm (4 ft x 8 ft x 0.140 in) aluminum waffle grid backwall with multilayer insulation and a 0.063-in shield. Acoustic data were gathered with transducers and associated data acquisition systems and stored for later analysis with a multichannel digitizer. Preliminary analysis of test data included sensor evaluation, impact repeatability, first waveform arrival, and Fourier spectral analysis.

Nelson, J. M.↗

Experience with approximations in the trust-region parallel direct search algorithm.

Recent years have seen growth in the number of algorithms designed to solve challenging simulation-based nonlinear optimization problems. One such algorithm is the Trust-Region Parallel Direct Search (TRPDS) method developed by Hough and Meza. In this paper, we take advantage of the theoretical properties of TRPDS to make use of approximation models in order to reduce the computational cost of simulation-based optimization. We describe the extension, which we call mTRPDS, and present the results of a case study for two earth penetrator design problems. In the case study, we conduct computational experiments with an array of approximations within the mTRPDS algorithm and compare the numerical results to the original TRPDS algorithm and a trust-region method implemented using the speculative gradient approach described by Byrd, Schnabel, and Shultz. The results suggest new ways to improve the algorithm.

97 MATHEMATICS AND COMPUTING↗

Surface penetrators for planetary exploration: Science rationale and development program

Work on penetrators for planetary exploration is summarized. In particular, potential missions, including those to Mars, Mercury, the Galilean satellites, comets, and asteroids are described. A baseline penetrator design for the Mars mission is included, as well as potential instruments and their status in development. Penetration tests in soft soil and basalt to study material eroded from the penetrator; changes in the structure, composition, and physical properties of the impacted soil; seismic coupling; and penetrator deflection caused by impacting rocks, are described. Results of subsystem studies and tests are given for design of entry decelerators, high-g components, thermal control, data acquisition, and umbilical cable deployment.

Murphy, J. P.↗

Energy Efficient Engine exhaust mixer model technology report addendum; phase 3 test program

The Phase 3 exhaust mixer test program was conducted to explore the trends established during previous Phases 1 and 2. Combinations of mixer design parameters were tested. Phase 3 testing showed that the best performance achievable within tailpipe length and diameter constraints is 2.55 percent better than an optimized separate flow base line. A reduced penetration design achieved about the same overall performance level at a substantially lower level of excess pressure loss but with a small reduction in mixing. To improve reliability of the data, the hot and cold flow thrust coefficient analysis used in Phases 1 and 2 was augmented by calculating percent mixing from traverse data. Relative change in percent mixing between configurations was determined from thrust and flow coefficient increments. The calculation procedure developed was found to be a useful tool in assessing mixer performance. Detailed flow field data were obtained to facilitate calibration of computer codes.

Larkin, M. J.↗

Design and Use of a Penetrating Deposition Nozzle for Z-Pinning Additive Manufacturing

Fused Filament Fabrication (FFF) involves depositing material layer-by-layer to create athree-dimensional object. This method often demonstrates high mechanical anisotropy in theprinted structure, leading to a drop in the material strength of the part when comparing structuresalong the deposition plane (X/Y-Axis) versus across layers in the build direction (Z-Axis). Initialefforts to improve anisotropy led to the development of the Z-Pinning process, where continuouspins are deposited across layers in the Z-Axis. Z-pinning has demonstrated significant gains intoughness and inter-layer strength, particularly in fiber-reinforced materials. However, thisprocess can also create flaws in the structure that increase in severity and frequency as the pinsgrow in length and diameter. To mitigate this, a penetrating nozzle has been developed thatextends a fine-tipped extrusion nozzle deep into the pin cavity and simultaneously extrudesmaterial as it retracts. This study investigates the printability of the penetrating nozzle for simplegeometries and evaluates the resulting Z-pinning mesostructure. As a result of this study, theprototype penetrating nozzle design was analyzed and built. Through a pressure driven flowanalysis it was determined that the penetrating nozzle extruder can not only flow extrudefilament. After a transient thermal simulation it was found that after a pause of 15 secondsresume printing with no drop in heat at nozzle exit.

Bales, Brenin↗

LaserSnake2: Remote High Powered Laser Cutting in Confined Hazardous Spaces - 16161

LaserSnake2, a UK collaborative project, seeks to deliver remotely operated cutting techniques into high hazard nuclear environments. This paper describes the developments and results of combining proven robotic manipulators with high-powered laser cutting tools, to allow for selective dismantling within complex nuclear process cells. Decommissioning old and poorly catalogued nuclear plant is a problem faced the world over. Designed with little consideration for decommissioning, or adapted significantly from the original drawings, legacy plant and infrastructure is full of spaces where it is undesirable or impossible to send people. Typically, a process cell or cave will require modification to ensure suitability for human entry or deployment of heavy duty equipment to complete the decontamination processes. The process of widening access routes, or selectively moving sections of highly contaminated material, is ideally suited to remote handling technology. The results of TWI's research into fibre-delivered laser cutting techniques, and integration with a dexterous snake-arm robot, are presented. Coupled with novel laser process head design and diffractive optical elements, the result is an integrated system capable of cutting up to 100 mm thick C-Mn steel plate at significant stand-off distances, encompassing the range of infrastructure found in a typical nuclear plant. Two options have been considered for deployment of the laser cutting tool. The first is focused on a fixed installation using a standard industrial robot. The second is a large, highly flexible snake-arm robot capable of entering cluttered cells through existing penetrations. Designed to operate through a standard 11'' MSM port, the 4.5 m snake-arm robot has the capacity to carry grippers, sensors or the laser cutting tool at the tip. The snake-arm is sealed and housed within a glove box for contamination control, allowing operation within a radioactive environment. Significant technical developments and material research are presented which have led to improved operational life, payload and bend. This paper describes the series of inactive trials which have been conducted to demonstrate the LaserSnake2 system's capabilities. These include: horizontal and vertical deployment, underwater operation, object manipulation and laser cutting. With global nuclear decommissioning costs running in to the $trillions, safe and cost efficient tools such as the LaserSnake2 system are essential as part of the decommissioning toolbox. Remote handling can account for up to 20% of a decommissioning project's costs, however significant time and financial savings can be made by utilising this new technology to reduce operator exposure and reach previously inaccessible areas. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Alignment Tool For Welding Sensor

Alignment tool enables accurate positioning of optoelectronic sensor measuring weld penetration. Designed for use on tungsten/inert-gas welding apparatus, used to adjust position of sensor so photodiode puts out maximum signal. Tangs of slotted cap bent slightly inward to provide spring force holding cap snugly on sensor mount. Tool installed and removed without aid of other tools. Length of pointer adjusted with set-screws. Used with variety of gas cup and electrode lengths.

Gilbert, Jeffrey L.↗

Assessing the Effects of Various Surface Textures and Features on Turbulent Heat Transfer in Hypersonic Flight

Experiments were conducted in the NASA Ames Hypervelocity Free Flight Aerodynamic Facility (ballistic range) to quantify the effects on turbulent convective heat transfer of distributed surface roughness, and of isolated features, representative of thermal protection systems on atmospheric entry vehicles. The surface textures and features were applied on the conic frusta of 45o sphere-cone models having a nose-to-base radius ratio of 0.5, similar to the forebody geometry of the Galileo and Pioneer-Venus entry probes. Test conditions were selected to provide turbulent roughness Reynolds numbers, k+, in the ranges expected for outer planet entry missions. Turbulent flow on the conic frustum was achieved by tripping the flow on the sphere-segment nose cap with distributed surface roughness, created by sand-blasting the nose cap. Surface textures included distributed, acreage, roughness, as well as cavity and groove discrete features. The majority of the data to be presented are results for distributed roughness, which includes both random, sand-grain-like roughness, and regular pattern roughness. The pattern roughness was designed to represent the roughness on woven thermal protection system materials, such as NASA’s 3-D Medium Density Carbon Phenolic (3MDCP), also known as HEEET, developed by the Heatshield for Extreme Entry Environments Technology project. The pattern roughness tested is a 3-D wavy surface, and includes three different roughness element height-to-spacing ratios representative of two configurations of 3MDCP, and spanning ratios measured both before, and after, ablation in an arc jet test facility. The patterns tested in the ballistic range were laser-etched on metal models, and represented an idealized version of the real-world materials in which each roughness element was nearly identical. Additional tests were performed wherein the laser-etched patterns were degraded by sand-blasting with various sized grit media, to produce regular patterns with superimposed irregular roughness, more representative of flight materials. Results of each will be compared. The discrete features tested included cylindrical cavities and rectangular grooves of various width-to-depth ratios. Cavities represent either heatshield damage, such as from micro-meteoroid and orbital debris (MMOD) damage, or from designed penetrations, such as on the Genesis sample return capsule. The grooves were scaled representations of seams between segments of HEEET material in a notional tiled thermal protection system. The tests examined the effects on turbulent heating downstream of the isolated features. The tests were conducted at speeds between 3 km/s and 4 km/s in air between 0.15 atm and 0.25 atm (Mach numbers between 9 and 12). Roughness Reynolds numbers, k+, ranged from 12 to 70 for the sand roughness, and as high as 200 for the pattern roughness. Boundary-layer parameters required for calculating k+ were evaluated using computational fluid dynamics simulations using the DPLR (Data Parallel Line Relaxation) code. Each model included both rough- and smooth-wall segments, and heat transfer augmentation factors were determined as the ratio of the rough-wall to smooth-wall heat flux measured on each test.

hypersonic↗

Pioneer Mars surface penetrator mission. Mission analysis and orbiter design

The Mars Surface Penetrator mission was designed to provide a capability for multiple and diverse subsurface science measurements at a low cost. Equipment required to adapt the Pioneer Venus spacecraft for the Mars mission is described showing minor modifications to hardware. Analysis and design topics which are similar and/or identical to the Pioneer Venus program are briefly discussed.

Source record↗

Symmetry structure of a Riccati equation appearing in penetration mechanics

In the design of projectile penetration experiments a matter of considerable interest is scaling: that is, the potential relevance of small-scale experiments to their full-scale counterparts, in a manner analogous to that most often encountered in the context of fluid mechanics. From the theoretical standpoint, phenomena associated with scaling and scalability can be assessed using the well-established tools of dimensional analysis and the Buckingham-Pi Theorem. However, the familiar precepts of dimensional analysis are themselves a specific manifestation of the broader group invariance properties or symmetries of a mathematical model. Here, this work explores these notions – that is, dimensional analysis, the conditions for realizing complete similarity, and any additional symmetry structures – in the context of a Riccati differential equation appearing in the context of penetration mechanics. The aim of the investigation is twofold: 1) to complement existing empirical considerations with a concrete theoretical basis, and 2) to provide a deeper theoretical understanding of the projectile penetration model and its many implications.

97 MATHEMATICS AND COMPUTING↗

Mars surface penetrator: System description

A point design of a penetrator system for a Mars mission is described. A strawman payload which is to conduct measurements of geophysical and meteorological parameters is included in the design. The subsystems used in the point design are delineated in terms of power, mass, volume, data, and functional modes. The prospects for survival of the rigors of emplacement are described. Data handling and communications plans are presented to allow consideration of the requirements placed by the penetrator on the orbiter and ground operations. The point design is technically feasible and the payload selection scientifically desirable.

Manning, L. A.↗