Search NASA⌕ Search

SEARCH · Search NASA

Results for “permanent mold casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Hot-Tearing Assessment of Multicomponent Nongrain-Refined Al-Cu Alloys for Permanent Mold Castings Based on Load Measurements in a Constrained Mold

The hot-tearing resistance of multicomponent Al-Cu alloys during permanent mold casting was investigated using a constrained permanent mold in which the load and temperature were measured. The nominal Cu composition was varied from 5 to 8 wt pct. Casting experiments were conducted without adding any grain-refining inoculants. The following variables, which were obtained from the measured load data during casting, were considered to assess the hot-tearing resistance of the Al-Cu multicomponent alloys: “V”-like signature in the load rate variation, load at solidus point, and load rate average over the freezing range. In addition, a hot-tearing criterion based on the variation of the fraction of solid in the late stages of solidification was used. It was found that all criteria considered can accurately predict the alloys with the lowest and highest hot-tear resistance, respectively. It was found that the rate of measured load during casting could be used to indicate substantial hot tearing. However, the load rate variation could not be used to detect when small hot tears were present. Among all the criteria considered, the load at the solidus point shows an excellent agreement with experimentally observed hot-tearing resistance for all but one alloy. The poorly resistant hot-tearing alloys exhibited mainly coarse columnar grains while the most hot-tearing resistant alloys exhibited a much more refined grain microstructure. This is the first study in which good hot-tear resistance is demonstrated for multicomponent Al-Cu alloys with nominal Cu content greater than 7 wt pct.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Light Metals Permanent Mold Casting

Current vehicles use mostly ferrous components for structural applications. It is possible to reduce the weight of the vehicle by substituting these parts with those made from light metals such as aluminum and magnesium. Many alloys and manufacturing processes can be used to produce these light metal components and casting is known to be most economical. One of the high integrity casting processes is permanent mold casting which is the focus of this research report. Many aluminum alloy castings used in automotive applications are produced by the sand casting process. Also, aluminum-silicon (Al-Si) alloys are the most widely used alloy systems for automotive applications. It is possible that by using high strength aluminum alloys based on an aluminum-copper (Al-Cu) system and permanent mold casting, the performance of these components can be enhanced significantly. This will also help to further reduce the weight. However, many technological obstacles need to be overcome before using these alloys in automotive applications in an economical way. There is very limited information in the open literature on gravity and low-pressure permanent mold casting of high strength aluminum alloys. This report summarizes the results and issues encountered during the casting trials of high strength aluminum alloy 206.0 (Al-Cu alloy) and moderate strength alloy 535.0 (Al-Mg alloy). Five engineering components were cast by gravity tilt-pour or low pressure permanent mold casting processes at CanmetMATERIALS (CMAT) and two production foundries. The results of the casting trials show that high integrity engineering components can be produced successfully from both alloys if specific processing parameters are used. It was shown that a combination of melt processing and mold temperature is necessary for the elimination of hot tears in both alloys.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Hybrid Al Casting + AM Components for Automotive Applications

Although casting Aluminum (Al) alloys is widely used for automotive application, the conventional casting process is showing limitations for modern vehicle production. A hybrid manufacturing method that is capable of fabricating automotive structures with tailored functionality and tuned attributes at a high production rate is proposed in this project, utilizing the merits of conventional casting methods and additive manufacturing (AM) methods. Ford is interested in supplementing conventional casting processes (e.g., shape casting, high pressure die casting) with local modifications to geometry and microstructure using additive manufacturing techniques. Two additive manufacturing methods, wire-arc and laser hot-wire directed energy deposition AM process, were evaluated by deposition of 4043 filler wire onto high-pressure die cast and permanent mold cast Al-Si alloys. The feasibility of this hybrid manufacturing method was determined through trial deposition and evaluation of defects, microstructure, and mechanical properties. Laser hot-wire deposition was found to be beneficial for this application with low porosity, a refined microstructure, and mechanical properties similar to those reported in the literature for 4043. The mechanical properties of the interface between the A356 casting and deposited 4043 were found to be controlled by the weaker deposit material.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Low-Cost Titanium Casting Technology

This is the final report of "Low-Cost Titanium Casting Technology" project. Titanium alloys have attracted increasing attentions as structural materials for high performance and weight-sensitive applications in aerospace and biomedical fields. However, in mass-production of civil applications like automotive components, titanium alloys are scarcely used due to the unaffordable costs in manufacturing compared with other metallic materials, such as aluminum, magnesium and steel. Therefore, there is a need to reduce the manufacturing cost of titanium alloys so that titanium alloys can be more competitive in terms of property and cost considerations. In this 4-year project, we started from exploring new low-cost titanium alloy systems with the guidance of Integrated Computational Materials Engineering – Calculation of Phase Diagram (ICME-CALPHAD) framework, and determined several promising alloy systems, alloying elements including Ti-Al-Fe-Mn-B-C, that can allow further development (lab-scale and industry-scale) in the future. During the new alloy system exploration, considerable amount of scientific work was completed regarding CALPHAD modeling, microstructure morphology, mechanical properties, and processing of the new alloy systems. The relevant ternary titanium alloy systems, Ti-Al-Mn and Ti-Al-Fe, were examined and reassessed both computationally and experimentally, leading to more comprehensive understanding of these alloy systems. Based on this above study, a new low-cost casting titanium alloy was developed, Ti-6Al-5Fe-0.05B-0.05C (designated as T65-0.05BC), which has competitive as-cast strength level with current commercial titanium alloys but relatively low ductility. However, in this project, since the target application, automotive engine connecting rod, is a fatigue-limited component and does not require high ductility, this alloy shall suffice as the deliverable alloy in this project. After designing and confirming the potent of the new alloy, we designed and built a lab-scale manufacturing equipment aided by computational tools at OSU labs to conceptually prove that this alloy can be manufactured with permanent mold casting, which is low-cost and potentially a mass production process. We produced a lab-scale prototype connecting rod demonstrating the capability of permanent mold casting of this new alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Hot-tearing of multicomponent Al-Cu alloys based on casting load measurements in a constrained permanent mold

Hot-tearing is a major casting defect that is often difficult to characterize, especially for multicomponent Al alloys used for cylinder head castings. The susceptibility of multicomponent Al-Cu alloys to hot-tearing during permanent mold casting was investigated using a constrained permanent mold in which the load and displacement was measured. The experimental results for hot tearing susceptibility are compared with those obtained from a hot-tearing criterion based temperature range evaluated at fraction solids of 0.87 and 0.94. The Cu composition was varied from approximately 5 to 8 pct. (weight). Casting experiments were conducted without grain refining. The measured load during casting can be used to indicate the severity of hot tearing. However, when small hot-tears are present, the load variation cannot be used to detect and assess hot-tearing susceptibility.

Sabau, Adrian S↗
DOE OSTI2020

Grain Refinement Effect on the Hot-Tearing Resistance of Higher-Temperature Al–Cu–Mn–Zr Alloys

The hot-tearing resistance of Al-Cu-Mn-Zr (ACMZ) alloys was investigated as a step toward introducing these new cast alloys for severe duty, higher-temperature applications, such as cylinder heads for down-sized, turbocharged automotive engines. Alloy Cu compositions were varied from 5 to 8 wt.%. Targeted Ti levels were 0.02, 0.1, and 0.2 wt.% via additions of the Al–5Ti–1B master alloy. Hot-tearing resistance was assessed by visual examination and ranking of the cracking severity in a multi-arm permanent mold casting. It was found that at high impurity contents (Fe and Si of 0.2 wt.% each), the Al–Cu–Mn–Zr alloy with 4.95 wt.% Cu exhibited the poorest hot-tearing resistance, irrespective of the grain refining amount. Microstructural analysis indicated an effective reduction in the grain size, as the Ti additions were increased to 0.02 and 0.1 wt.% Ti via the Al–Ti–B grain refiner. The finest grain size was attained with a 0.1 wt.% Ti. Based on the hot-tearing evaluation, it was found that the additional grain refining via the Al–5Ti–1B master alloy at 0.1 wt.% Ti significantly reduces the hot-tearing susceptibility at Cu contents greater than 7.3 wt.% for ACMZ alloys with low Fe and Si. These findings indicate that the best hot-tearing resistance was observed at a grain refiner level of 0.1 wt.% Ti and high Cu content (greater than 7.3 wt.%). This study to indicates that these Al–Cu–Mn–Zr alloys, which possess excellent microstructural stability and mechanical properties at elevated temperatures, can also possess excellent hot-tearing resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mitigate Stress Corrosion Cracking (SCC) in High-strength Al Castings (CRADA 508)

Development of high strength, corrosion resistant, aluminum alloys is important to a number of industries, including automotive, aerospace, power, etc. Understanding how processing methods such as casting, chemistry, additives and recycle content affect an alloy’s microstructure and performance in real world environments is crucial to their implementation. One major concern is how the repeated exposure to saline solutions can be detrimental to the structural integrity of aluminum alloy components. This study was undertaken as a collaboration between Eck Industries and PNNL to investigate the stress corrosion cracking (SCC) and corrosion behavior of aluminum alloys. This work examines the SCC response of three different materials set. First is cast A206 Al alloy produced by three different casting techniques (i.e., permanent mold, and sand casting with and without chill) and with or without nano forming additives as potential grain refiners. The second materials set comprises Al alloy tubes extruded by PNNL’s ShAPE process and produced using raw material with three different ratios of twitch and pre-consumer Al 6061 scrap. Finally, the third materials set comprises two Al-Si-Mg-Fe alloys with controlled Si% and Fe% to mimic recycle grade Al alloys. The corrosion behavior of these materials was characterized using SCC testing and scanning electrochemical cell microscopy (SECCM) technique; mechanical behavior was characterized using tensile testing, and microstructure was characterized using optical and electron microscopy techniques. Of the A206 Al alloys, the samples with nano forming additives performed poorly compared to those without. The best SCC performance (i.e. least degradation in mechanical properties) was demonstrated by A206 alloy sand cast with chill while the permanent mold sample showed the worst SCC performance. The SECCM was performed on A206 alloy sand cast with chill to understand the effect of microstructure and determine the location-dependent corrosion properties on grain boundaries (GB) and inside grains (IG) on the sample. The corrosion potential and current measured on GB and IG at various points on the sample established that the GB locations are more cathodic and corrosive than the IG locations. Further work needs to be conducted to investigate the mechanisms behind the observed dependence of SCC on casting technique and nano forming additives. Among the ShAPE extruded tubes, SECCM data suggests the decreasing order of tendency to corrode as follows: 100% twitch > 75% twitch > 50% twitch. Finally, both variants of the Al-Si-Mg-Fe alloys showed a large volume fraction of Fe- and Si-containing intermetallics and additional work is needed to discern differences in their respective corrosion responses. In summary, correlating local electrochemical behavior (e.g. via SECCM) with micro/nanostructure, in conjunction with bulk mechanical behavior, can help identify the right fabrication method and alloy chemistry to minimize SCC issues in Al alloys.

36 MATERIALS SCIENCE↗
NASA NTRS2005

GRCop-84: A High Temperature Copper-based Alloy For High Heat Flux Applications

While designed for rocket engine main combustion chamber liners, GRCop-84 (Cu-8 at.% Cr-4 at.% Nb) offers potential for high heat flux applications in industrial applications requiring a temperature capability up to approximately 700 C (1292 F). GRCop-84 is a copper-based alloy with excellent elevated temperature strength, good creep resistance, long LCF lives and enhanced oxidation resistance. It also has a lower thermal expansion than copper and many other low alloy copper-based alloys. GRCop-84 can be manufactured into a variety of shapes such as tubing, bar, plate and sheet using standard production techniques and requires no special production techniques. GRCop-84 forms well, so conventional fabrication methods including stamping and bending can be used. GRCop-84 has demonstrated an ability to be friction stir welded, brazed, inertia welded, diffusion bonded and electron beam welded for joining to itself and other materials. Potential applications include plastic injection molds, resistance welding electrodes and holders, permanent metal casting molds, vacuum plasma spray nozzles and high temperature heat exchanger applications.

Ellis, David L.↗
DOE OSTI2017

Casting Development Report for EFF-W Casting Furnace

The Experimental Fuels Facility (EFF) Casting System, which is configured for gravity casting into a permanent mold, was installed to cast billets made up of uranium, uranium alloys, copper and copper alloys, as well as other geometries in support of the TerraPower project. This document describes casting development using.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2000

Low Cost Al-Si Casting Alloy As In-Situ Composite for High Temperature Applications

A new aluminum-silicon (Al-Si) alloy has been successfully developed at NASA- Marshall Space Flight Center (MSFC) that has significant improvement in tensile and fatigue strength at elevated temperatures (500 F-700 F). The alloy offers a number of benefits such as light weight, high hardness, low thermal expansion and high surface wear resistance. In hypereutectic form, this alloy is considered as an in-situ Al-Si composite with tensile strength of about 90% higher than the auto industry 390 alloy at 600 F. This composite is very economically produced by using either conventional permanent steel molds or die casting. The projected material cost is less than $0.90 per pound, and automotive components such as pistons can be cast for high production rate using conventional casting techniques with a low and fully accounted cost. Key Words: Metal matrix composites, In-situ composite, aluminum-silicon alloy, hypereutectic alloy, permanent mold casting, die casting.

Lee, Jonathan A.↗
NASA NTRS2003

Cast Aluminum Alloy for High Temperature Applications

Originally developed by NASA as high performance piston alloys to meet U.S. automotive legislation requiring low exhaust emission, the novel NASA alloys now offer dramatic increase in tensile strength for many other applications at elevated temperatures from 450 F (232 C) to about 750 F (400 C). It is an ideal low cost material for cast automotive components such as pistons, cylinder heads, cylinder liners, connecting rods, turbo chargers, impellers, actuators, brake calipers and rotors. It can be very economically produced from conventional permanent mold, sand casting or investment casting, with silicon content ranging from 6% to 18%. At high silicon levels, the alloy exhibits excellent dimensional stability, surface hardness and wear resistant properties.

Lee, Jonathan A.↗
NASA NTRS2003

High Strength and Wear Resistant Aluminum Alloy for High Temperature Applications

Originally developed by NASA as high performance piston alloys to meet U.S. automotive legislation requiring low exhaust emission, the novel NASA alloys now offer dramatic increase in tensile strength for many other applications at elevated temperatures from 450 F (232 C) to about 750 F (400 C). It is an ideal low cost material for cast automotive components such as pistons, cylinder heads, cylinder liners, connecting rods, turbo chargers, impellers, actuators, brake calipers and rotors. It can be very economically produced from conventional permanent mold, sand casting or investment casting, with silicon content ranging from 6% to 18%. At high silicon levels, the alloy exhibits excellent thermal growth stability, surface hardness and wear resistant properties.

Lee, Jonathan A.↗
NASA NTRS1980

Preparation of cast aluminum alloy-mica particle composites

A method for making aluminum-mica particle composites is presented in which mica particles are stirred in molten aluminum alloys followed by casting in permanent molds. Magnesium is added either as an alloying element or in the form of pieces to the surface of the alloy melts to disperse up to 3 wt% mica powders in the melts and to obtain high recoveries of mica in the castings. The mechanical properties of the aluminum alloy-mica composite decrease with increasing mica content; however, even at 2.2% it has a tensile strength of 14.22 kg/sq mm with 1.1% elongation, a compression strength of 42.61 kg/sq mm, and an impact strength of 0.30 kgm/sq cm. Cryogenic and self-lubricating bearing are mentioned applications.

Deonath, MR.↗
DOE OSTI2017

Casting Characteristics of High Cerium Content Aluminum Alloys

This paper compares the castability of the near eutectic aluminum-cerium alloy system to the aluminum-silicon and aluminum-copper systems. The alloys are compared based on die filling capability, feeding characteristics and tendency to hot tear in both sand cast and permanent mold applications. The castability ranking of the binary Al–Ce systems is as good as the aluminum-silicon system with some deterioration as additional alloying elements are added. In alloy systems that use cerium in combination with common aluminum alloying elements such as silicon, magnesium and/or copper, the casting characteristics are generally better than the aluminum-copper system. In general, production systems for melting, de-gassing and other processing of aluminum-silicon or aluminum-copper alloys can be used without modification for conventional casting of aluminum-cerium alloys.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Commercialization of NASA's High Strength Cast Aluminum Alloy for High Temperature Applications

In this paper, the commercialization of a new high strength cast aluminum alloy, invented by NASA-Marshall Space Flight Center, for high temperature applications will be presented. Originally developed to meet U.S. automotive legislation requiring low- exhaust emission, the novel NASA aluminum alloy offers dramatic improvement in tensile and fatigue strengths at elevated temperatures (450 F-750 F), which can lead to reducing part weight and cost as well as improving performance for automotive engine applications. It is an ideal low cost material for cast components such as pistons, cylinder heads, cylinder liners, connecting rods, turbo chargers, impellers, actuators, brake calipers and rotors. NASA alloy also offers greater wear resistance, dimensional stability, and lower thermal expansion compared to conventional aluminum alloys, and the new alloy can be produced economically from sand, permanent mold and investment casting. Since 2001, this technology was licensed to several companies for automotive and marine internal combustion engines applications.

Lee, Jonathan A.↗
NASA NTRS2009

Cast Aluminum Alloys for High Temperature Applications Using Nanoparticles Al2O3 and Al3-X Compounds (X = Ti, V, Zr)

In this paper, the effect of nanoparticles Al2O3 and Al3-X compounds (X = Ti, V, Zr) on the improvement of mechanical properties of aluminum alloys for elevated temperature applications is presented. These nanoparticles were selected based on their low cost, chemical stability and low diffusions rates in aluminum at high temperatures. The strengthening mechanism at high temperature for aluminum alloy is based on the mechanical blocking of dislocation movements by these nanoparticles. For Al2O3 nanoparticles, the test samples were prepared from special Al2O3 preforms, which were produced using ceramic injection molding process and then pressure infiltrated by molten aluminum. In another method, Al2O3 nanoparticles can also be homogeneously mixed with fine aluminum powder and consolidated into test samples through hot pressing and sintering. With the Al3-X nanoparticles, the test samples are produced as precipitates from in-situ reactions with molten aluminum using conventional permanent mold or die casting techniques. It is found that cast aluminum alloy using nanoparticles Al3-X is the most cost effective method to produce high strength aluminum alloys for high temperature applications in comparison to nanoparticles Al2O3. Furthermore, significant mechanical properties retention in high temperature environment could be achieved with Al3-X nanoparticles, resulting in tensile strength of nearly 3 times higher than most 300- series conventional cast aluminum alloys tested at 600 F.

Lee, Jonathan A.↗
NASA NTRS1998

High-Strength Aluminum Casting Alloy for High-Temperature Applications (MSFC Center Director's Discretionary Fund Final Project No. 97-10)

A new aluminum-silicon alloy has been successfully developed at Marshall Space Flight Center that has a significant improvement in tensile strength at elevated temperatures (550 to 700 F). For instance, the new alloy shows in average tensile strength of at least 90 percent higher than the current 390 aluminum piston alloy tested at 500 F. Compared to conventional aluminum alloys, automotive engines using the new piston alloy will have improved gas mileage, and may produce less air pollution in order to meet the future U.S. automotive legislative requirements for low hydrocarbon emissions. The projected cost for this alloy is less than $0.95/lb, and it readily allows the automotive components to be cast at a high production volume with a low, fully accounted cost. It is economically produced by pouring molten metal directly into conventional permanent steel molds or die casting.

Lee, J. A.↗