SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Vapor phase conversion of 3-hydroxybutyric and crotonic acid to propylene in a continuous-flow reactor over silica–alumina and niobium catalysts demonstrates a new strategy for producing renewable fuels and chemicals from wastewater carbon.
The role of amplitude-to-phase conversion as a factor in feedback oscillator flicker phase noise is examined. A limiting stage consisting of parallel-connected opposite polarity diodes operating in a circuit environment contining reactance is shown to exhibit amplitude-to-phase conversion. This mechanism coupled with resistive upconversion provides an indirect route for very low frequency flicker noise to be transferred into the phase of an oscillator signal. It is concluded that this effect is more significant in the lower frequency regimes where the onlinear reactances associated with active devices are overwhelmed by linear reactive elements.
This study investigates Ga-doped n-type PbTe thermoelectric materials and the dynamic phase conversion process of the second phases via Cu 2 Se alloying. Introducing Cu 2 Se enhances its electrical transport properties while reducing its lattice thermal conductivity (κlat) via weak electron–phonon coupling. Additionally, Cu 2 Te and CuGa(Te/Se) 2 (tetragonal phase) nanocrystals precipitate during the alloying process, resulting in Te vacancies and interstitial Cu in the PbTe matrix. At room temperature, Te vacancies and interstitial Cu atoms serve as n-type dopants, increasing the carrier concentration and electrical conductivity from ≈1.18 × 10 19 cm –3 and ≈1870 S cm –1 to ≈2.26 × 10 19 cm –3 and ≈3029 S cm –1 , respectively. With increasing temperature, the sample exhibits a dynamic change in Cu 2 Te content and the generation of a new phase of CuGa(Te/Se) 2 (cubic phase), strengthening the phonon scattering and obtaining an ultralow k lat . Pb 0.975 Ga 0.025 Te-3%CuSe exhibits a maximum figure of merit of ≈1.63 at 823 K, making it promising for intermediate-temperature device applications.
Sodium ion batteries have been receiving increasing attention and may see potential revival in the near future, particularly in large-scale grid energy storage coupling with wind and solar power generation, due to the abundant sodium resources, low cost, and sufficiently high energy density. Among the known sodium ion conductors, the Na-β”-alumina electrolyte remains highly attractive because of its high ionic conductivity. This study focuses on the vapor phase synthesis of a Na-β”-Alumina + YSZ (Naβ”AY) composite sodium electrolyte, which has higher mechanical strength and stability than conventional single phase β”-Alumina. The objectives are the measurement of conversion kinetics through a newly developed weight-gain based model and the determination of sodium ionic conductivity in the composite electrolyte. Starting samples contained ~70 vol% α-Alumina and ~30 vol% YSZ (3 mol% Y 2 O 3 stabilized Zirconia) with and without a thin alumina surface layer made by sintering in air at 1600 °C. The sintered samples were placed in a powder of Na-β”-alumina and heat-treated at 1250 °C for various periods. Sample dimensions and weight were measured as a function of heat treatment time. The conversion of α-Alumina in the α-Alumina + YSZ composite into Naβ”AY occurred by coupled diffusion of sodium ions through Na-β”-alumina and of oxygen ions through YSZ, effectively diffusing Na2O. From the analysis of the time dependence of sample mass and dimensions, the effective diffusion coefficient of Na 2 O through the sample, D eff , was estimated to be 1.74 x 10 -7 cm2 s -1 , and the effective interface transfer parameter, k eff , was estimated as 2.33 x 10 -6 cm s -1 . By depositing a thin alumina coating layer on top of the bulk composite, the chemical diffusion coefficient of oxygen through single phase Na-β”-alumina was estimated as 4.35 x 10 -10 cm 2 s -1 . An AC impedance measurement was performed on a fully converted Naβ”AY composite, and the conductivity of the composite electrolyte was 1.3 x 10 -1 S cm -1 at 300 °C and 1.6 x 10 -3 S cm -1 at 25 °C, indicating promising applications in solid state or molten salt batteries at low to intermediate temperatures.
Not Available
The influence of the rate of heating on the position of the critical points of iron-cobalt alloys was studied. It is shown that when an alloy with 8% Co by weight is heated at the rate of 7000 deg/sec, a shift in the temperature of phase conversion of almost 30 deg occurs. When an alloy with 15% Co by weight is heated at the same rate, the conversion temperature is shifted by approximately 20 deg. For an alloy with 15% Co by weight, for which under ordinary conditions of heating the points of phase conversion and magnetic randomization (the Curie point) coincide, it was possible to show that for high rates of heating, a separation with respect to temperature occurs which clearly confirms the fact of the shift in the critical points of phase conversion.
Not provided.
Explore the source record for details and available documents.
Moiré superlattices have reshaped condensed‐matter physics by enabling twist‐angle engineering of electronic and excitonic states, traditionally in van der Waals (vdW) systems. This Perspective focuses on perovskites as a transformative non‐van der Waals (non‐vdW) platform for twistronics. These materials are distinguished by ionic‐covalent bonding and soft octahedral lattices that support deep moiré potentials (≈100–200 meV), which in turn yield bright, room‐temperature excitons and tunable quantum phenomena. We organize recent advances into two core classes: (i) moiré superlattices constructed from 2D Ruddlesden‐Popper (RP) perovskites via spontaneous or guided twisted stacking; and (ii) moiré architectures in 3D perovskite lamellae, achieved through topotactic 2D RP‐to‐3D conversion and ligand‐induced self‐assembly. Key experimental observations in these systems include twist‐tunable moiré periods, suppressed exciton–exciton annihilation, flat band‐like transport, and ferroelectric vortex lattices in their oxide perovskite counterparts. Here, we outline key bottlenecks, including defects arising during phase conversion, stringent lattice‐matching requirements, and the absence of in situ twist metrology, and highlight opportunities in lattice‐mismatched heterostructures and multifunctional quantum‐optoelectronic devices. Collectively, these advances establish perovskite moiré systems as a critical bridge between fundamental moiré physics and room‐temperature technological applications.
Conventional epitaxy of semiconductor films requires a compatible single crystalline substrate and precisely controlled growth conditions, which limit the price competitiveness and versatility of the process. We demonstrate substrate-tolerant nano-heteroepitaxy (NHE) of high-quality formamidinium-lead-tri-iodide (FAPbI 3 ) perovskite films. The layered perovskite templates the solid-state phase conversion of FAPbI 3 from its hexagonal non-perovskite phase to the cubic perovskite polymorph, where the growth kinetics are controlled by a synergistic effect between strain and entropy. The slow heteroepitaxial crystal growth enlarged the perovskite crystals by 10-fold with a reduced defect density and strong preferred orientation. This NHE is readily applicable to various substrates used for devices. The proof-of-concept solar cell and light-emitting diode devices based on the NHE-FAPbI 3 showed efficiencies and stabilities superior to those of devices fabricated without NHE.
Zeolitic imidazolate frameworks (ZIFs) are nanoporous molecular sieves offering exciting opportunities for membrane- and adsorption-based gas separations. The Tsapatsis group developed an all-vapor-phase ligand induced permselectivation (LIPS) method for the fabrication of ZIF nanocomposite membranes. The LIPS method consists of a combination of atomic layer deposition of a dense oxide inside the mesopores of a porous support followed by transformation of the dense oxide deposit to nanoporous ZIF by exposure to sublimated vapors of an imidazolate ligand. It enables the formation of thin nanocomposite films consisting of ZIF deposited inside pores with diameters smaller than 10 nm. Vapor-phase conversion of the impermeable ZnO to ZIF increases flux of certain gases more than others. Vapor phase linker/ligand treatment (VPLT) can further modify the properties of LIPS and other membranes. The combination of LIPS with VPLT provides an all-vapor methodology for making and modifying ZIF membranes with the ability to control the ZIF deposit composition and the level of confinement in a variety of mesoporous supports. The propylene/propane separation performance of LIPS/VPLT ZIF membranes confined (entirely or partially) inside mesopores is remarkably superior to that of most conventional ZIF membranes consisting of unconfined (deposited on the external surface of porous supports) polycrystalline films. The accomplishments of this award are: (i) understanding of the LIPS process using mathematical models of atomic layer deposition (ALD), (ii) development of surface modification methods (vapor, e-beam, plasma, and X-ray treatments) to tune permeation properties, (iii) microstructural control of ZIF-8 films using ALD (support modification, direct ALD, and by use of in situ permeability monitoring), (iv) molecular simulations, and (v) thin film characterization and adsorption measurements using spectroscopy.
Titanium disulfide (TiS 2 ) with high electric conductivity, fast rate capability, and good cycling performance is a promising candidate for electrode material in sodium (Na)-ion batteries. Despite the well-studied electrochemical behaviors of TiS 2 in Li-ion batteries, the detailed reaction mechanism of TiS 2 in Na-ion batteries is not yet fully understood due to a more complex multi-phase conversion process. In this work, reactions of TiS 2 in Na-ion batteries are investigated via a multi-modal synchrotron approach: operando X-ray Absorption Spectroscopy (XAS) – including X-ray Absorption Near-Edge Structure (XANES) and Extended X-ray Absorption Fine Structure (EXAFS) – and ex situ X-ray Powder Diffraction (XPD), coupled with computational modeling. Operando XANES spectra indicate that the redox reactions occur in both Ti and S during the electrochemically driven phase transformation. Multivariate Curve Resolution-Alternating Least Squares (MCR-ALS) analysis of XAS suggests that different numbers of components are involved in the lithiation and sodiation of TiS 2 , with the sodiation including at least one intermediate phase in addition to the starting material and the final sodiation product. Ex situ XPD and Rietveld refinement further determined and quantified the unknown phases, showing that three phases, TiS 2 , Na 0.55 TiS 2 , and NaTiS 2 , participate in the sodiation of TiS 2 . Operando EXAFS results show the changes in the Ti–Ti coordination number and interatomic distance. This explains the coulombic efficiency decay due to the incomplete recovery of the coordination number of Ti after cycling. Overall, this work reveals the reaction mechanism occurring in Na–TiS 2 batteries with a greater quantitative understanding of the structural evolution. By combining the multi-modal synchrotron approach and computational work, this study provides a framework for studying a broader range of electrochemically driven phase-transformation systems towards advanced energy storage and conversion applications.
Earlier studies on the influence of solar activity variations within a 11-year solar cycle on temperature changes in the middle atmosphere revealed that while the temperature in the mesosphere showed strong responses to changes in solar activity, the stratosphere remained almost unaffected. Recent studies showed that when the temperature data were grouped into east or west phase of the equatorial quasi-biennial oscillation (QBO) in stratospheric zonal wind, significant relationships of temperature in the lower stratosphere and troposphere could be obtained with 10.7 cm solar radio flux. Positive correlations in high latitude regions and negative correlations in mid-latitude and tropical regions were obtained during winter when the QBO was in its west phase. During the east phase, converse relationships were indicated. These results inspired this study on the response of solar activity in 11-year cycle on the temperature structure of the middle atmosphere in the two phases of equatorial QBO of zonal wind at 50 mb, in tropics, mid-latitude and antarctic regions.
Enzymes selectively hydrolyze the carbohydrate fractions of lignocellulosic biomass into corresponding sugars, but these processes are limited by low yields and slow catalytic turnovers. Under certain conditions, the rates and yields of enzymatic sugar production can be increased by pretreating biomass using solvents, heat, and dilute acid catalysts. However, the mechanistic details underlying this behavior are not fully elucidated, and designing effective pretreatment strategies remains an empirical challenge. Herein, using a combination of solid-state and high-resolution magic-angle-spinning NMR, infrared spectroscopy, and X-ray diffractometry, we show that the extent to which cellulase enzymes are able to hydrolyze solvent-pretreated biomass can be understood in terms of the ability of the solvent to break the chemical linkages between cellulose and noncellulosic materials in the cell wall. This finding is of general significance to enzymatic biomass conversion research, and implications for designing improved biomass conversion strategies are discussed. Furthermore, these findings demonstrate the utility of solid-state NMR as a tool to elucidate the key chemical and physical changes that occur during the liquid-phase conversion of real biomass.
Flame-spray-pyrolysis (FSP) is a robust and scalable process to synthesize particles at the commodity-scale. FSP has been used to produce the precursor powders which were converted to the layered structure $(R\bar{3m} \text { phase})$ by a postannealing step in making nickel-rich cathode materials (NCMs). Theoretically, the high flame temperature (normally >1500 K) in FSP can provide adequate energy for the phase conversion from rock-salt to layered structures and potentially enables one-step synthesis. However, the high flame temperature is a critical issue to cause lithium loss and structural degradation, preventing the formation of the layered phase. Here, guided by the gaseous nucleation theory, we implemented several FSP processes with different solution recipes. The layered phase concentration in the as-burned products can be increased with the solution enthalpies. By adding a rapid quench step to suppress the lithium loss and phase degradation, the layered phase can be further increased. This work contributes new ideas to innovating process regarding the process efficiency and throughput of manufacturing cathode materials at a large scale.
The fabrication of a nanohybrid photocatalyst that combines α-Fe 2 O 3 nanoparticles with graphitic carbon nitride (g-C 3 N 4 ) is reported. The ensuing direct Z-scheme heterojunction greatly boosts the photocatalytic activity of the α-Fe 2 O 3 /g-C 3 N 4 nanohybrids. This results in organic dye degradation rates more than two times higher than its individual components, promoted by the efficient charge separation and transfer of the Z-scheme heterojunction mechanism of the nanohybrid photocatalyst. In addition, recyclability tests show an outstanding stability of the nanohybrids spanning five consecutive dye degradation experiments, during which the degradation rate is slightly improved. The origin of the improved photocatalytic performance of the nanohybrid lies in the intimate interaction between α-Fe 2 O 3 and g-C 3 N 4 afforded by the two-step fabrication process, which enables the direct and controlled growth of α-Fe 2 O 3 nanoparticles on g-C 3 N 4 . A first ultrasound impregnation step promotes the effective anchoring of stable Fe species via Fe–N and C–N/C–O bonding, while a second microwave phase conversion step induces the subsequent growth of α-Fe 2 O 3 nanoparticles on the g-C 3 N 4 sheets. Careful control of the FeCl 3 precursor concentration up to a threshold value of 0.25 M during impregnation enables complete control over their size and phase. This approach clearly highlights the benefits of microwave reactor systems in the fabrication of hematite-based Z-scheme photocatalytic, overcoming the limitations of conventional thermal treatment technology.
Sodium yttrium fluoride (NaYF 4 ) is an important upconverting material with many potential uses in chemistry, materials science, and biology, which can be synthesized hydrothermally in both cubic (α) and hexagonal (β) crystallographic polymorphs. Understanding the mechanisms underlying the phase conversion between the cubic and hexagonal polymorphs is of great interest to help inform future synthetic efforts, for example in the design of atomically precise quantum materials with well-defined sizes and morphologies. In this work, we use a combination of analytical transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM), powder X-ray diffraction (XRD), in situ liquid cell TEM, atom probe tomography (APT), and extended X-ray absorption fine structure (EXAFS) measurements to show that the hexagonal NaYF 4 nanowires form through a nonclassical crystal growth mechanism involving the formation and subsequent oriented attachment of mesocrystals consisting of cubic (α) phase units. Additionally, EXAFS measurements suggest that substitutional Yb 3+ point defects within NaYF 4 are distributed evenly throughout the crystal lattice without clustering and also that they may exhibit selective substitution into one of the two possible trivalent yttrium sites in the unit cell for hydrothermally synthesized β-NaYF 4 .