SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Phase errors cancelled for high frequency stability. Radio-frequency oscillator achieves high stability of frequency through parallel, two-amplifier configuration in which effects cause phase noise tend to cancel each other. Circuit includes two amplifiers with resonating elements, each constitutes part of feedback loop of other. Generate same frequency because each circuit provides other with conditions necessary for oscillation.
The total noise of a phased-array antenna system employing a photonic feed network is analyzed using a model for the individual component noise including both additive and multiplicative equivalent noise generators.
RF differential phase noise (RF modulation sideband phase noise): phase jitter between the optical sideband generated from phase modulation and the optical carrier. Clock noise information of each space craft (s/c) is imprinted on the RF modulation sidebands and transferred between s/c through beating of the sidebands. Therefore, it is necessary to manage the RF modulation phase noise as light propagates from the phase modulator to the power amplifier delivery fiber.
A low phase noise frequency divider composed of a grating arrangement is disclosed. The grating arrangement supplies selected portions of an input reference signal to be divided to a tuned circuit without any phase noise due to the grating action. The arrangement which in one embodiment consists of an FET is connected to the tuned circuit input to short out the input except when the input reference signal amplitude crosses ground level in a positive direction and a gate enabling signal is present at the gate electrode of the FET. The gate enabling signal alone does not decouple the tuned circuit input from ground, therefore phase noise, due to the leading and trailing edges of each gate-enabling signal, is substantially eliminated.
Phase noise of single mode laser diodes, either free-running or using line narrowing technique at room temperature, namely injection-locking, has been investigated. It is shown that free-running diodes exhibit very large excess phase noise, typically more than 80 dB above shot-noise at 10 MHz, which can be significantly reduced by the above-mentioned technique.
The Laser Interferometer Space Antenna (LISA) mission is a collaborative consortium led by the European Space Agency (ESA)in cooperation with the National Aeronautics and Space Administration (NASA). LISA’s goal is to capture gravitational wave events, such as spacetime distortions caused by massive orbiting bodies. Multiple low noise, single frequency master oscillator power amplifier (MOPA) lasers with a polarization-maintaining Yb-fiber amplifier will serve as the light sources for the LISA observatory. The NASA Goddard Space Flight Center (GSFC)is currently developing the laser transmitters for this project. The LISA lasers will carry radio frequency (RF)sidebands for exchanging reference RF clock information between spacecrafts. Excess phase noise, especially carrier-sideband differential phase noise added to the modulation side band by the phase modulator and the fiber amplifier, becomes a concern. In the gravitational wave frequency ranges, leading sources of this RF “differential” phase noise can be both intrinsic and extrinsic. Examples of intrinsic sources include thermal load on the active fiber, thermo-mechanical induced birefringence, and nonlinearities in the various passive and active fibers. Extrinsic sources can include external temperature fluctuations and infrasonic mechanical strain or vibrations. These noise spectra usually include both white and pink (1/f) thermal noise contributions. This work investigates the physical origins and impact of these sources of RF phase noise, and their characteristic spectra and management will be discussed.
As qubit decoherence times are increased and readout technologies are improved, nonidealities in the drive signals, such as phase noise, are going to represent a growing limitation to the fidelity achievable at the end of complex control pulse sequencies. Here we study the impact on fidelity of phase noise affecting reference oscillators with the help of numerical simulations, which allow us to directly take into account the interaction between the phase fluctuations in the control signals and the evolution of the qubit state. Our method is based on the generation of phase noise realizations consistent with a given power spectral density, that are then applied to the pulse carrier in simulations, with Qiskit-Dynamics, of the qubit temporal evolution. By comparing the final state obtained at the end of a noisy pulse sequence with that in the ideal case and averaging over multiple noise realizations, we estimate the resulting degradation in fidelity, and exploiting an approximate analytical representation of a carrier affected by phase fluctuations, we discuss the contributions of the different spectral components of phase noise.
VIPR (Vapor Inside-cloud Profiling Radar) is a differential absorption radar operating over 155-175 GHz, covering a portion of the lower frequency flank of the 183 GHz water vapor absorption resonance. Transmitting at a ~1.9 mm wavelength, VIPR is highly sensitive to scattering from small particles comprising clouds and precipitation. Variation of VIPR’s cloud and precipitation echo power with frequency is often dominated by water vapor absorption, allowing humidity profiles to be retrieved along the radar’s beam path. One confounding effect in practical measurements is phase noise carried by the radar’s transmit signal, which can result in strong range sidelobes extending from bright targets and obscuring the echo signals of more weakly scattering clouds. Here we show that the magnitude and shape of phase-noise induced clutter from extended, bright cloud signals can be accurately modeled using a combination of empirical measurements of surface-echo phase noise and an analytic model based on the phase-noise sidelobe magnitude from a theoretical point target. This improved understanding of a potential clutter source in millimeter-wave imagine radar can lead to better performance modeling, and it provides motivation to improve the phase noise of very high frequency local oscillators.
Close-in optical interferometric noise spectrum and its conversion to RF close-in phase noise are theoretically and experimentally studied. The study also indicates that reflective type devices and optically amplified links enhance the interferometric phase noise degradation.
EPSD has designed, fabricated and tested, ultra-stable, low phase noise microwave dielectric resonator oscillators (DRO's) at S, X, Ku, and K-bands, for potential application to high dynamic range and low radar cross section target detection radar systems. The phase noise and the temperature stability surpass commercially available DROs. Low phase noise signals are critical for CW Doppler radars, at both very close-in and large offset frequencies from the carrier. The oscillators were built without any temperature compensation techniques and exhibited a temperature stability of 25 parts per million (ppm) over an extended temperature range. The oscillators are lightweight, small and low cost compared to BAW & SAW oscillators, and can impact commercial systems such as telecommunications, built-in-test equipment, cellular phone and satellite communications systems. The key to obtaining this performance was a high Q factor resonant structure (RS) and careful circuit design techniques. The high Q RS consists of a dielectric resonator (DR) supported by a low loss spacer inside a metal cavity. The S and the X-band resonant structures demonstrated loaded Q values of 20,300 and 12,700, respectively.
Low-phase-noise microwave-frequency integrated oscillators provide compact solutions for various applications in signal processing, communications, and sensing. Surface acoustic waves (SAWs), featuring orders-of-magnitude shorter wavelength than electromagnetic waves at the same frequency, enable integrated microwave-frequency systems with much smaller footprint on chip. SAW devices also allow higher-quality (Q) factors than electronic components at room temperature. Here, we demonstrate a low-phase-noise gigahertz-frequency SAW oscillator on 128°Y-cut lithium niobate, where the SAW resonator occupies a footprint of 0.05 mm 2 . Leveraging phononic crystal band-gap-edge modes to balance between Q factors and insertion losses, our 1-GHz SAW oscillator features a low phase noise of -132.5 dBc/Hz at a 10-kHz offset frequency and an overlapping Hadamard deviation of 6.5 × 10 -10 at an analysis time of 64 ms. The SAW resonator-based oscillator holds high potential in developing low-noise sensors and acousto-optic integrated circuits.
A set of measurements performed by the Michigan Tech Sensing and Signal Processing Group on the analog receiver built by the Virginia Polytechnic Institute (VPI) and the Jet Propulsion Laboratory (JPL) for propagation measurements using the Olympus Satellite is described. Measurements of local oscillator (LO) phase noise were performed for all of the LOs supplied by JPL. In order to obtain the most useful set of measurements, LO phase noise measurements were made using the complete VPI receiver front end. This set of measurements demonstrates the performance of the receiver from the Radio Frequency (RF) input through the high Intermediate Frequency (IF) output. Three different measurements were made: LO phase noise with DC on the voltage controlled crystal oscillator (VCXO) port; LO phase noise with the 11.381 GHz LO locked to the reference signal generator; and a reference measurement with the JPL LOs out of the system.
The characterization of precision frequency standard phase noise and spurious outputs is addressed, using the two-oscillator coherent downconversion technique. Focus is on techniques for making accurate measurements of phase noise and spurious outputs within 100 KHz of a carrier. Significant sources of measurement error related to hardware design problems and inadequate measurement procedures are discussed: measurement errors resulting from system noise sources, phase-locked loop effects, and system bandwidth limitations. In addition, methods and design considerations for minimizing the effects of such errors are presented. Analytic discussions and results are supplemented with actual test data and measurements made using measurement hardware developed at the Ball Corporation, Efratom Division.
A digital signal-processing meter for phase noise measurement on sinusoidal signals is dealt with. It enlists a special hardware architecture, made up of a core digital signal processor connected to a data acquisition board, and takes advantage of a quadrature demodulation-based measurement scheme, already proposed by the authors. Thanks to an efficient measurement process and an optimized implementation of its fundamental stages, the proposed meter succeeds in exploiting all hardware resources in such an effective way as to gain high performance and real-time operation. For input frequencies up to some hundreds of kilohertz, the meter is capable both of updating phase noise power spectrum while seamlessly capturing the analyzed signal into its memory, and granting as good frequency resolution as few units of hertz.
The role of amplitude-to-phase conversion as a factor in feedback oscillator flicker phase noise is examined. A limiting stage consisting of parallel-connected opposite polarity diodes operating in a circuit environment contining reactance is shown to exhibit amplitude-to-phase conversion. This mechanism coupled with resistive upconversion provides an indirect route for very low frequency flicker noise to be transferred into the phase of an oscillator signal. It is concluded that this effect is more significant in the lower frequency regimes where the onlinear reactances associated with active devices are overwhelmed by linear reactive elements.
Microwave oscillators of proposed new type incorporate suppressed-carrier/negative-feedback feature to reduce phase noise near their carrier frequencies. Concept results in phase noise less than achievable by cryogenically stabilized microwave components or by room-temperature oscillators stabilized by quartz crystals. Implemented in three different versions.
Measuring the phase fluctuation between a pair of low-power microwave signals, the signals must be amplified before detection. In such cases the phase noise of the amplifier pair is the main cause of 1/f background noise of the instrument. this article proposes a scheme that makes amplification possible while rejecting the close in 1/f (flicker) noise of the two amplifiers. Noise rejection, which relies upon the understanding of the amplifier noise mechanism does not require averaging. Therefore, our scheme can also be the detector of a closed loop noise reduction system. the first prototype, compared to a traditional saturated mixer system under the same condition, show a 24 dB noise reduction of the 1/f region.
The Electron Ion Collider (EIC) presently under construction at Brookhaven National Laboratory will collide polarized high energy electron beams with hadron beams with luminosities up to 10^34 cm?^2 s^?1 in center mass energy range of 20-140 GeV. Crab cavities are used to compensate the geometric luminosity due to a large crossing angle 25 mrad in the EIC. It was found that the phase noise in crab cavities will generate a significant emittance growth for the hadron beams. The phase noise tolerance from the analytical calculation is very small for the Hadron Storage Ring (HSR) of the EIC. In this article, we present our preliminary numerical simulation results with a 6-d symplectic particle tracking to determine the proton emittance growth rate with crab cavity phase noise and beam-beam interaction for the HSR.