Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase transformation kinetics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

The role of ternary alloying elements in eutectoid transformation of U-10Mo alloy part II. In and Ex-situ Neutron diffraction-based assessment of eutectoid phase transformation kinetics in U-9.8Mo-0.2X alloy (X = Cr, Ni or Co)

HExploring the effects of minor ternary alloying additions, typically impurity elements, on the phase stability of U-10Mo is important for preventing undesirable phase decomposition during processing or during service. This work examines the influence small ternary additions of Cr, Ni, and Co. Both in-situ and ex-situ neutron diffraction measurements made during and after high temperature (450 – 525°C) exposures were used to better define the influence of these elements on the time-temperature-transformation (TTT) behavior of U-10Mo, providing information which is complementary to electron microscopy investigations of the same alloy systems performed in the first part of this work. Minor additions of Ni and Co decrease the ?-phase stability at all temperatures investigated. Signatures of U6X (X = Ni or Co) compounds were shown to be present in amounts of up to 6 wt% in the heat treated alloys, suggesting that the initial precipitation of this phase may catalyze further ?-phase decomposition. On the other hand, the Cr containing alloys were observed to have nearly the same, and in some cases slower, phase transformation kinetics when compared to the binary U-10Mo control samples. The results of the study have enabled preliminary estimates of the TTT curves for the ternary alloys.

phase transformation, kinetics, discontinuous prec↗
DOE OSTI2025

Phase transformation kinetics model for metals

We develop a new model for phase transformation kinetics in metals by generalizing the Levitas–Preston (LP) phase field model of martensite phase transformations (see Levitas and Preston (2002a,b) and Levitas et al. (2003)) to arbitrary pressure. Furthermore, we account for and track: the interface speed of the pressure-driven phase transformation, properties of critical nuclei, as well as nucleation at grain sites and on dislocations and homogeneous nucleation. The volume fraction evolution of each phase is described by employing KJMA (Kolmogorov, 1937; Johnson and Mehl, 1939; Avrami, 1939, 1940, 1941) kinetic theory. We then test our new model for iron under ramp loading conditions and compare our predictions for the α → ϵ iron phase transition to experimental data of Smith et al. (2013). In conclusion, more than one combination of material and model parameters (such as dislocation density and interface speed) led to good agreement of our simulations to the experimental data, thus highlighting the importance of having accurate microstructure data for the sample under consideration.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Predicting phase transformation kinetics during metal additive manufacturing using non-isothermal Johnson-Mehl-Avrami models: Application to Inconel 718 and Ti-6Al-4V

Here, a computational model was developed to predict solid-state phase transformation kinetics within mechanical parts during metal additive manufacturing processes. This model is a modified version of the Johnson-Mehl-Avrami model for non-isothermal phase transformations that can be applied to various material systems undergoing solid-state phase transformations. Using the thermal history of an additive manufacturing fabricated mechanical part, along with the necessary thermodynamic data and kinetic information as inputs, the model outputs the history of phase fraction evolution during the build process. The model was applied to an Inconel 718 part built by powder bed fusion and a Ti-6Al-4V part built by directed energy deposition. Microstructure characterization and mechanical testing were performed for the validation of the model.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Kinetics of moisture-induced phase transformation in inorganic halide perovskite

The high-temperature (high-T) phase of cesium lead iodide (CsPbI 3 ) presents great promise for photovoltaic applications; however, exposure to ambient moisture at room temperature transforms it into its less-desirable low-temperature (low-T) phase with a larger band gap. While there have been theoretical predictions on the influence of moisture level on the phase transformation kinetics, the corresponding quantitative experimental evidence has remained limited. Tracking CsPbI 3 phase transformation under controlled relative humidity (RH), we find that rising RH increases the nucleation rate of low-T CsPbI 3 exponentially, but has a weak effect on its growth. The overall transformation is nucleation limited, with higher RH leading to a lower nucleation barrier. Finally, we find that heating between 40°C and 80°C facilitates water desorption and suppresses phase transformation. Our findings elucidate the relationship between moisture and the phase energetics of CsPbI 3 , which can serve as references for thin film applications of CsPbI 3 and future designs of stable photovoltaics systems.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase transformation and growth mechanism of RF sputtered ferroelectric lead scandium tantalate (PbSc 0.5 Ta 0.5 O 3 ) films

Lead scandium tantalate (PbSc 0.5 Ta 0.5 O 3 , PST), an order/disorder ferroelectric, is a potential candidate for electrocaloric cooling and pyroelectric infrared (IR) detector. In this work, we report the phase transformation kinetics from two series of samples containing pure amorphous and mixture of amorphous and pyrochlore to desired perovskite phase using postdeposition rapid thermal processing (RTP) as well as growth mechanism of RF sputtered PST thin films using excess lead target on platinized silicon (Pt/Ti/SiO 2 /Si) substrates. We find that small changes in the temperature ramp have a large effect on the degree of perovskite conversion (ferroelectric phase), orientation (crystallographic texture), and long-range order parameter (< S 111 >). Through isothermal annealing, we obtained optimal perovskite phase at ≥700°C temperature. The phase transformation is characterized by spontaneous formation of center-type in-plane radial rosette-like structures revealed by scanning electron microscopy. The PST perovskite crystallites were found to coexist with pyrochlore in RTP annealed films. The volume fractions for perovskite and pyrochlore phase were obtained from the analysis of “rosettes” and respective X-ray diffraction intensities which helped to determine various parameters associated with phase kinetics (n, k, and activation energy, Ea) and accompanying growth. The effective activation energies of perovskite transition and growth were found to be 332 ± 11 kJ/mol (345 ± 11 kJ/mol) and 114 ± 10 kJ/mol (122 ± 10 kJ/mol), respectively, for pure amorphous only (and mixed amorphous and pyrochlore) phase following nucleation-growth controlled Avrami's equation. A linear growth rate (n~1) for the perovskite phase indicates predominant interface-controlled process and diffusion-limited phenomena thus inhibiting rosette size owing to reactant depletion and soft impingement at the grain boundary. However, the growth behavior is isotropic in two-dimension parallel to the plane of the substrates for both sample series. Furthermore, lead loss was severe for in-situ growth and RTP combined with conventional furnace annealing than those of RTP only films, which were closer to stoichiometric albeit with excess lead and marginal oxygen vacancies (V o ).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding Instability in Formamidinium Lead Halide Perovskites: Kinetics of Transformative Reactions at Grain and Subgrain Boundaries

Transformative and reconstructive reactions impart significant structural changes at particle boundaries of hybrid perovskites, which influence environmental stability and optoelectronic properties of these materials. Here, we investigate the moisture-induced transformative reactions in formamidinium based perovskites FAPbX 3 (X=I, Br) and show that the ambient stability of these materials can be adjusted from a few hours to several months. For FAPbI 3 , roles of water vapor, particle size, and light illumination on the kinetic pathways of the cubic (a) transformation to the hexagonal (d) phase are analyzed by X-ray diffraction, optical microscopy, photoluminescence and solid-state NMR spectroscopy techniques. The grain and sub-grain boundaries exhibit different α→δ-FAPbI 3 phase transformation kinetics. Our study suggests that the dynamic transformation involves the local water-induced dissolution of the cubic phase occurring at the crystal surfaces followed by precipitation of the hexagonal phase. Insights into structures and dynamics of a kinetically trapped α-|δ-FAPbI 3 are obtained by 1 H, 2 H, and 207 Pb ssNMR spectroscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Coupled Small and Wide-Angle X-Ray Scattering Study of Phase Transformation Mechanisms in U-6Wt Pct Nb

The elevated temperature phase transformation kinetics of U-6wt%Nb in both wrought and cast conditions were investigated using in-situ high energy synchrotron X-ray scattering. The evolution of the phase content, γ-phase composition, and microstructure morphology was determined through the analysis of simultaneously collected wide-angle diffraction and small-angle scattering (SAXS) data. The results of the wide-angle scattering analysis, especially the phase fractions and average composition of the γ-phase, provide model parameters to enable a quantitative analysis using the SAXS data. Greater clarity regarding the kinetics of different precipitation mechanisms, namely the continuous precipitation (CP) of α-U within the γ-phase matrix and the discontinuous (DP) grain boundary precipitation of a lamellar microstructure, consisting of α-U and Nb-rich γ-phase are obtained from the coupled measurement modes. These results indicate that the CP mechanism is responsible for the initial precipitation of α-U at all temperatures considered. Near the nose in the time-temperature-transformation (TTT) diagram at ~798 K, both mechanisms are active during the early stages of phase transformation. However, the DP mechanism has an increasingly long incubation period with decreasing temperature below the TTT nose. In conclusion, the average interlamellar spacing obtained from the SAXS analysis increases with time, providing further evidence of the so-called divergent DP behavior previously observed in U-6wt%Nb alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Navigating phase diagram complexity to guide robotic inorganic materials synthesis

Abstract Efficient synthesis recipes are needed to streamline the manufacturing of complex materials and to accelerate the realization of theoretically predicted materials. Often, the solid-state synthesis of multicomponent oxides is impeded by undesired by-product phases, which can kinetically trap reactions in an incomplete non-equilibrium state. Here we report a thermodynamic strategy to navigate high-dimensional phase diagrams in search of precursors that circumvent low-energy, competing by-products, while maximizing the reaction energy to drive fast phase transformation kinetics. Using a robotic inorganic materials synthesis laboratory, we perform a large-scale experimental validation of our precursor selection principles. For a set of 35 target quaternary oxides, with chemistries representative of intercalation battery cathodes and solid-state electrolytes, our robot performs 224 reactions spanning 27 elements with 28 unique precursors, operated by 1 human experimentalist. Our predicted precursors frequently yield target materials with higher phase purity than traditional precursors. Robotic laboratories offer an exciting platform for data-driven experimental synthesis science, from which we can develop fundamental insights to guide both human and robotic chemists.

Chen, Jiadong (ORCID:0009000476038838)↗
DOE OSTI2021

Magnetic ordering suppressed phase transformation of a TRIP-HEA during thermal cycling

Transformation-induced plasticity (TRIP) high-entropy alloys (HEAs) have drawn great attention as they present excellent mechanical properties, and their phase stability is critical for the underlying deformation mechanisms and the application temperature range. In this study, the kinetic phase transformation behavior of a dual-phase TRIP-HEA Fe 50 Mn 30 Co 10 Cr 10 (at. %) was probed by in situ neutron diffraction during thermal cycling between 293 and 425 K. Continuous austenitic and martensitic transformation were visualized through the evolution of hexagonal close-packed phase fraction during thermal cycling. Specifically, thanks to the magnetic sensitivity of neutron diffraction, it was found that the martensitic transformation under cooling became suppressed when the antiferromagnetic ordering started at ~326 K. This temperature was further confirmed as the Néel temperature by magnetization measurements. In this work, thermodynamic calculations revealed that the suppression effect on martensitic transformation is attributed to the consumption of the chemical driving force by the magnetic ordering. The magnetic ordering at such relatively high temperature is associated with the high Mn content. These findings shed light on a potential strategy to achieve better mechanical properties of Mn-containing alloys by manipulating the magnetic property through tuning the Mn content.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Phase-Field Model for In-Space Manufacturing of Binary Alloys

The integrity of the final printed components is mostly dictated by the adhesion between the particles and phases that form upon solidification, which is a major problem in printing metallic parts using available In-Space Manufacturing (ISM) technologies based on the Fused Deposition Modeling (FDM) methodology. Understanding the melting/solidification process helps increase particle adherence and allows to produce components with greater mechanical integrity. We developed a phase-field model of solidification for binary alloys. The phase-field approach is unique in capturing the microstructure with computationally tractable costs. The developed phase-field model of solidification of binary alloys satisfies the stability conditions at all temperatures. The suggested model is tuned for Ni-Cu alloy feedstocks. We derived the Ginzburg-Landau equations governing the phase transformation kinetics and solved them analytically for the dilute solution. We calculated the concentration profile as a function of interface velocity for a one-dimensional steady-state diffuse interface neglecting elasticity and obtained the partition coefficient, k, as a function of interface velocity. Numerical simulations for the diluted solution are used to study the interface velocity as a function of undercooling for the classic sharp interface model, partitionless solidification, and thin interface.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Limited-Ranged Two-Phase Iron Equation of State Model

This report describes the construction of a two-phase EOS for Fe that includes both (hcp) and liquid phases, and which is meant to be valid over the restricted range: V ϵ [4 : 7] °A 3 /atom, and T ϵ [1000 : 20000] K. It was recently used as the basis for a theoretical study of liquid → solid phase transformation kinetics in Fe which appeared in the Supplemental Material for a paper describing a series of NIF shock + ramp compression experiments aimed at constraining the high-P melt curve of Fe.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Hardness Prediction by Incorporating Heat Transfer and Molten Pool Fluid Flow in a Multi-pass, Multi-layer Weld for Onsite Repair of Grade 91 steel

Introduction: In the current fleet of fossil-fired power plants, creep strength enhanced ferritic steels (CSEF) are used to sustain the harsh service conditions. Enhanced properties of Grade 91 steel result from tempered martensite with a fine distribution of MX and M23C6 carbides. Grade 91 steel is subjected to onsite welding repair to remedy their degradation due to extreme service condition. Knowledge of weld repairability of these steels, such as as-welded hardness distribution, is essential to establishing sound repair procedures. Experimental trial and error tests can consume a lot of time as many welding variables need to be studied. For numerical modelling, most of the multi-pass multi-layer models are based on finite element method, which are limited to solve the heat conduction equation and ignore convective heat transfer due to melt flow. Moreover, the mesh has to be pre-built based on a known or assumed weld cross-section geometry. These finite element based models thus have limited predictive capability as defects are not considered and nugget size are pre-assumed. This research aims at developing a thermal and microstructure evolution model incorporating molten pool dynamics in a multi-pass multi-layer material deposition to predict the as-welded hardness distribution. Technical Approach: All the thermal, physical, and metallurgical properties of Grade 91 as a function of temperature are collected from the literature and inputted into the thermo-fluid model based on Flow-3D, a computational fluid dynamics software. A multi-pass, multi-layer material deposition is simulated where the melting of filler wire into the molten pool is directly considered based on the volume of fluid (VOF) method. The flow behaviour of the molten pool is used to understand the formation of deposition geometry and defects. The temperature profiles during the multi-pass, multi-layer welding are calculated. The results computed using the new model are compared against the experimental data of fusion zone geometry and thermal cycles. Hardness prediction in the heat-affected zone (HAZ) are made using Johnson-Mehl-Avrami (JMA) equation for solid-state phase transformation kinetics. The JMA parameters are extracted from the experimental data available in the literature. For comparison, a standard finite element heat conduction model is also developed to predict the thermal cycles and hardness distribution in the multi-pass, multi-layer weld. Expected Result: Results obtained using the molten pool dynamic simulation versus the finite element heat conduction model are compared. Specifically, the effects of convective heat transfer on the accuracy of the calculated thermal history, bead shape and size, and HAZ hardness distribution are examined.

Modeling, Grade 91 steel, Multi-pass multi-layer d↗