Search NASA⌕ Search

SEARCH · Search NASA

Results for “piezoelectric materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Irradiation Behavior of Piezoelectric Materials for Nuclear Reactor Sensors

In-situ measurement of surface acoustic wave (SAW) resonators were used to characterize piezoelectric materials behavior in a nuclear reactor environment. Lithium niobate and aluminum nitride devices were tested up to 500°C temperature and 450 kW reactor power (1.9x10 12 n/cm 2 s). The resonant frequency responds to step changes in temperature and power. Materials’ response are inferred from the observed resonant frequency changes, in particular the kinetic behavior is used to determine mechanisms responsible for observed changes. The observed response is attributed to two mechanisms: temperature increase from gamma heating and accumulation of radiation-induced defects. Both of these mechanisms alter the physical properties of the piezoelectric materials, particularly the elastic constants. The demonstrated repeatability and reliability of SAW devices are attractive for sensor applications in extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Optimizing Piezoelectric Material Location and Size for Multiple-Mode Vibration Reduction of Turbomachinery Blades

Modern turbomachinery blades have extremely low inherent damping, which can lead to high transient vibrations and failure through high-cycle fatigue. Smart materials enable vibration reduction while meeting strict blade requirements such as weight and aerodynamic efficiency. In particular, piezoelectric-based vibration reduction offers the potential to reduce vibration semi-actively while simultaneously harvesting sufficient energy to power the implementation. The placement and the size of the piezoelectric material is critical to the vibration reduction capabilities of the system. Furthermore, the implementation should target multiple vibration modes. In this study, we develop a procedure to optimize electromechanical coupling across multiple vibration modes for a representative turbomachinery blade with surface-mounted piezoelectric patches. Experimental validation demonstrates good coupling across three targeted modes with a single piezoelectric patch. Placing the piezoelectric material in regions of high signed strain energy for all targeted modes enables vibration reduction across all of the targeted modes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Revisiting Structural and Electromechanical Properties of the Lead-free (K,Na)NbO 3 High-Piezoelectric Material

Having lead-free systems with excellent piezoelectric responses is crucial to the development of environmentally friendly electromechanical applications. In this work, we build an effective Hamiltonian model to explore the promising (K x Na 1–x )NbO 3 system, whose rich phase diagram near x = 50% remains poorly understood meanwhile exhibiting a colossal effective piezoelectric response. Thanks to the numerical implementation of this effective Hamiltonian scheme into a Monte Carlo Metropolis algorithm, we reveal striking features. First, a long-period state can be the ground state at low temperatures for some concentrations while only a short-period conventional polar ground state exists for larger x. Second, the electric field-driven transformation, via a first-order transition, of this long-period state into a short-period polar state creates large electromechanical strains (on the order of the percent) and is likely the origin of the colossal piezoelectric response reported in KNN, for which we evaluate an effective piezoelectric coefficient of several thousands of pC/N.

(K,Na)NbO3↗
DOE OSTI2023

Study of Different Piezoelectric Material Stroke Displacement at Different Temperatures Using an SRF Cavity

Piezoelectric actuators are used for resonance control in superconducting linacs. The level of frequency compensation depends on the piezoelectric stroke displacement. In this study, the stroke displacement will be measured with a 1.3 GHz SRF cavity by measuring the frequency shift with respect to the voltage applied. The entire system was submerged in liquid helium. This study characterizes the PZT piezoelectric actuator (P-844K093) and a lithium niobate (P-844B0005) piezoelectric actuator. All these actuators were developed at Physik Instrumente (PI). The piezoelectric displacement was measured at different temperatures.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Piezoelectric property of PZT nanofibers characterized by resonant piezo-force microscopy

Nano-piezoelectric materials have drawn tremendous research interest. However, characterization of their piezoelectric properties, especially measuring the piezoelectric strain coefficients, remains a challenge. Normally, researchers use an AFM-based method to directly measure nano-materials’ piezoelectric strain coefficients. But, the extremely small piezoelectric deformation, the influence from the parasitic electrostatic force, and the environmental noise make the measurement results questionable. In this paper, a resonant piezo-force microscopy method was used to accurately measure the piezoelectric deformation from 1D piezoelectric nanofibers. During the experiment, the AFM tip was brought into contact with the piezoelectric sample and set to work at close to its first resonant frequency. A lock-in amplifier was used to pick up the sample’s deformation signal at the testing frequency. By using this technique, the piezoelectric strain constant d 33 of the Lead Zirconate Titanate (PZT) nanofiber with a diameter of 76 nm was measured. The result showed that d 33 of this PZT nanofiber was around 387 pm/V. Meanwhile, by tracking the piezoelectric deformation phase image, domain structures inside PZT nanofibers were identified.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Unlocking AlN Piezoelectric Performance with Earth‐Abundant Dopants

Abstract The increasing demand for high‐performance piezoelectric materials and toxicity and thermal stability issues of the widely used lead zirconate titanates (PZT) have spurred a search for better alternatives in electronic devices. In comparison to PZT, group III nitrides such as aluminum nitride (AlN), are only weakly piezoelectric, but doping AlN with scandium (Sc) improves the piezoelectric response by nearly 500%. Relative to PZT, doped‐AlN piezoelectric materials are advantageous because they are far more compatible with complementary metal–oxide–semiconductor (CMOS) materials, and they maintain both piezoelectric and thermodynamic stability up to very high temperatures. Unfortunately, rare‐earth metals are notoriously expensive, and fabricating stable films with rare‐earth dopants is also challenging, limiting their use in industrial applications. In this work, ab initio calculations are combined with targeted fabrication and experimentation to identify alternative earth‐abundant dopants for AlN from the periodic table d‐block. Amongst the 23 elements screened, it is found that group IVB metals, titanium, zirconium, and hafnium induce large piezoelectric enhancements comparable to Sc. This improvement is traced to shifts in the atomic sublattice structure and changes in the local charge states. In demonstrating a highly accessible and affordable path for technological adaptation of AlN‐based piezoelectrics, this work provides the foundation for sustainable, next‐generation electronics.

Startt, Jacob↗
DOE OSTI2021

High-Performance Piezoelectric MEMS Manufacturing & Application on Micro Power Generators (CRADA Final Report)

This project aimed to develop and characterize a micro-fabrication technology for wafer-scale heterogeneous integration of bulk piezoelectric materials on silicon substrates that could enable manufacturing of high-performance micro transducers. Typical technical challenges for piezoelectric microfabrication technologies are high-temperature processing, non-uniform film quality, and low process repeatability, which will be addressed during this project. Progress was made on preliminary research towards development of a technology platform that will enable a new micro-fabrication process to provide the highest electromechanical coupling among any other thin/thick-film deposition methods available today. This work has tested and characterized samples that we hope will further our goal of refining and enabling existing micro transducers to achieve unprecedentedly high performance. This project focused solely on the characterization of the proposed microfabrication process technology, and it did not consist of design or manufacturing of new transducers, such as sensors, actuators or energy harvesters based on this fabrication process. Future work will be aimed at the research and development of process steps specifically to enable integration of on-chip electronics with piezoelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Unlocking Electrostrain in Plastically Deformed Barium Titanate

Achieving substantial electrostrain alongside a large effective piezoelectric strain coefficient (d 33 *) in piezoelectric materials remains a formidable challenge for advanced actuator applications. Here, in this work, a straightforward approach to enhance these properties by strategically designing the domain structure and controlling the domain switching through the introduction of arrays of ordered {100}<100> dislocations is proposed. This dislocation engineering yields an intrinsic lock-in steady–state electrostrain of 0.69% at a low field of 10 kV cm -1 without external stress and an output strain energy density of 5.24 J cm -3 in single-crystal BaTiO 3 , outperforming the benchmark piezoceramics and relaxor ferroelectric single-crystals. Additionally, applying a compression stress of 6 MPa fully unlocks electrostrains exceeding 1%, yielding a remarkable d 33 * value over 10 000 pm V -1 and achieving a record-high strain energy density of 11.67 J cm -3 . Optical and transmission electron microscopy, paired with laboratory and synchrotron X-ray diffraction, is employed to rationalize the observed electrostrain. Phase-field simulations further elucidate the impact of charged dislocations on domain nucleation and domain switching. These findings present an effective and sustainable strategy for developing high-performance, lead-free piezoelectric materials without the need for additional chemical elements, offering immense potential for actuator technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Long-range quadrupole electron-phonon interaction from first principles

Lattice vibrations in materials induce perturbations on the electron dynamics in the form of long-range (dipole and quadrupole) and short-range (octopole and higher) potentials. The dipole Fröhlich term can be included in current first-principles electron-phonon (e-ph) calculations and is present only in polar materials. The quadrupole e-ph interaction is present in both polar and nonpolar materials, but currently it cannot be computed from first principles. In this work, we show an approach to compute the quadrupole e-ph interaction and include it in ab initio calculations of e-ph matrix elements. The accuracy of the approach is demonstrated by comparing with direct density functional perturbation theory calculations. We apply our method to silicon as a case of a nonpolar semiconductor and tetragonal PbTiO 3 as a case of a polar piezoelectric material. In both materials we find that the quadrupole term strongly impacts the e-ph matrix elements. Analysis of e-ph interactions for different phonon modes reveals that the quadrupole term mainly affects optical modes in silicon and acoustic modes in PbTiO 3 , although the quadrupole term is needed for all modes to achieve quantitative accuracy. The effect of the quadrupole e-ph interaction on electron scattering processes and transport is shown to be important. Our approach enables accurate studies of e-ph interactions in broad classes of nonpolar, polar, and piezoelectric materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Enhanced ferroelectric and piezoelectric properties of BCT-BZT at the morphotropic phase boundary driven by the coexistence of phases with different symmetries

The discovery of lead-free piezoelectric materials is crucial for future information and energy storage applications. Enhanced piezoelectric and other physical properties are commonly observed near the morphotropic phase boundary (MPB) composition of ferroelectric solid solutions. The (1 – x)Ba(Zr 0.2 Ti 0.8 )O 3 -x(Ba0.7Ca0.3)TiO 3 (BZT-xBCT) system exhibits a large electromechanical response around its MPB region at x = 0.5. Here, we report experimental and theoretical results of BZT-xBCT over a wide composition range (0.3 ≤ x ≤ 1.0). X-ray diffraction and Raman spectroscopy studies indicate a composition-induced structural phase transition from a rhombohedral (R3m) phase at x ≤ 0.4 to a tetragonal (P4mm) phase at x ≥ 0.6 through a multiphase coexistence region at 0.45 ≤ x ≤ 0.55 involving orthorhombic + tetragonal (Amm2 + P4mm) phases. First-principles calculations elucidate the phase competition in the coexistence region. The critical composition (x = 0.5) displays enhanced dielectric, ferroelectric, and piezoelectric properties, where notably d 33 ~ 320 pC/N. This paper provides clear evidence of Amm2+P4mm crystallographic phases in the MPB region, which is responsible for the improved functional properties.

MPB↗
DOE OSTI2020

Sound Speed as a Candidate for Internal Temperature Monitoring During Solid Phase Processing of Materials

Internal temperature is an important parameter for understanding the solid phase processing (SPP) of materials and improving feedback control of these processes. Friction stir processes, shear assisted processing and extrusion (ShAPE ™ ), and ultrahigh velocity (UHV) cold spray are examples of such processes. Simple thermal models based on temperatures measured at the boundary of the deforming body cannot capture the dynamic nature of temperature generation within the deforming solid. One possibly way of understanding internal temperature is by measuring sound speed, which varies as a function of temperature for materials and directing ultrasonic wave propagation through selected material volumes of interest. In this project, longitudinal wave speed is estimated for aluminum 6061. Piezoelectric materials bonded to a specimen provided data from which longitudinal wave speed was estimated. A discussion evaluated the linear relationship of wave speed versus temperature and postulated how wave speed measurements could be used to estimate the internal temperature of selected material volumes for feedback during SPP of materials. Instrumentation, data and analysis, and a discussion are reviewed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electrical de-poling and re-poling of relaxor-PbTiO 3 piezoelectric single crystals without heat treatment

Re-poling of unexpected partially depoled piezoelectric materials conventionally needs to be first fully depoled through annealing above their Curie temperature to revive piezoelectric performances. Here, we investigated de-poling and re-poling of Pb(In 1/2 Nb 1/2 )O 3 -Pb(Mg 1/3 Nb 2/3 )O 3 -PbTiO 3 single crystals under electric fields at room temperature. We found that alternating current electric fields with amplitudes near the coercive field at low frequencies (<10 Hz) can be employed to successfully depolarize poled crystals at room temperature. We also demonstrated a reversible polarization switching process with a relaxor-PbTiO 3 single crystal ultrasound transducer without device performance degradations. This experimental observation is supported by phase-field simulation, showing that alternating current electric fields can readily induce de-poling at room temperature, while direct current electric fields induce a transient depoled state only within an uncontrollable short period of time. The findings suggest new strategies for unprecedented in-device tailoring of the polarization states of ferroelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Systems, devices, and methods for contact measurement and modulation of material properties

Materials and devices are provided for the sensing and manipulation of biomechanical and physiochemical properties of tissues or tissue surfaces. Examples of use include soft tissues such as skin or adipose tissues or more dense tissues such as muscle or heart or dense tissues such as bone. The materials and devices provide for in vivo measurements of biomechanical properties at the tissue surface, e.g. near surface regions of the epidermis or dermis or underlying structures. The devices can be non-invasive and/or non-destructive to the material and, especially for the biomaterials, can be biocompatible and/or biodegradable. The materials and devices can use ultrathin, stretchable networks of mechanical actuators and sensors constructed with nanoribbons of piezoelectric materials.

Dagdeviren, Canan↗
DOE OSTI2021

Precipitation Hardening in Ferroelectric Ceramics

Domain wall motion in ferroics, similar to dislocation motion in metals, can be tuned by well-concepted microstructural elements. In demanding high-power applications of piezoelectric materials, the domain wall motion is considered as a lossy hysteretic mechanism that should be restricted. Current applications for so-called hard piezoelectrics are abundant and hinge on the use of an acceptor-doping scheme. However, this mechanism features severe limitations due to enhanced mobility of oxygen vacancies at moderate temperatures. By analogy with metal technology, the authors present here a new solution for electroceramics, where precipitates are utilized to pin domain walls and improve piezoelectric properties. Through a sequence of sintering, nucleation, and precipitate growth, intragranular precipitates leading to a fine domain structure are developed as shown by transmission electron microscopy, piezoresponse force microscopy, and phase-field simulation. This structure impedes the domain wall motion as elucidated by electromechanical characterization. As a result, the mechanical quality factor is increased by ≈50% and the hysteresis in electrostrain is suppressed considerably. This is even achieved with slightly increased piezoelectric coefficient and electromechanical coupling factor. This novel process can be smoothly implemented in industrial production processes and is accessible to simple laboratory experimentation for microstructure optimization and implementation in various ferroelectric systems.

36 MATERIALS SCIENCE↗