Search NASA⌕ Search

SEARCH · Search NASA

Results for “planar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

3D Multiphysics Model for Large Scale Planar Cell: Inductance Investigation in Impedance Analysis

Developed a comprehensive 3D multiphysics model to analyze impedance behavior in large-scale planar Solid Oxide Fuel Cells (SOFCs). The model investigates how impedance varies across operating conditions and cell components, with a particular focus on inductive loops or negative capacitance at the air electrode. It was found that the Inductive loop disappears in the low-frequency zone when the activation overpotential or faradic current is not temperature-dependent. These findings offer new insights into SOFC impedance behavior.

impedence analysis↗
DOE OSTI2024

Reliability of Materials and Components for Solid Oxide Fuel Cells

Planar stack solid-oxide fuel cells (SOFCs) require seals that must operate reliably under demanding conditions for lifetimes of 40000 hours. This includes temperature fluctuations between 800°C and RT during on and off cycles, thermal stresses, oxidizing environments and chemical degradation to name a few. This comprehensive report provides results from long term testing of two commercially available multicomponent barium alkali silicate glasses: SCN and G6, chosen as sealing candidates. In this scope, the glass seals were deposited on YSZ and Al 2 O 3 substrates simulating electrolytes (Zrbased) and coatings (both zirconia and Al 2 O 3 ). The seal-substrate couples were subjected to 800°C under air and steam+H 2 +N 2 environments up to 40000 hours to test their integrity under real operating conditions. Extensive studies on the effects of exposure have been conducted over the span of testing at various time intervals. Within the context of characterization, mechanical properties such as density, roughness, thermal expansion and glass transition, viscosity and wettability behavior; and microstructural properties such as glass chemistries, defect formation (cracks and pores), phase transformations (devitrification) and glass-interface reactions are investigated. Results and discussions are provided with a focus on the degradation of the properties over long term interrupted testing.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

The little skate genome and the evolutionary emergence of wing-like fins

Skates are cartilaginous fish whose body plan features enlarged wing-like pectoral fins, enabling them to thrive in benthic environments. However, the molecular underpinnings of this unique trait remain unclear. Here we investigate the origin of this phenotypic innovation by developing the little skate Leucoraja erinacea as a genomically enabled model. Analysis of a high-quality chromosome-scale genome sequence for the little skate shows that it preserves many ancestral jawed vertebrate features compared with other sequenced genomes, including numerous ancient microchromosomes. Combining genome comparisons with extensive regulatory datasets in developing fins—including gene expression, chromatin occupancy and three-dimensional conformation—we find skate-specific genomic rearrangements that alter the three-dimensional regulatory landscape of genes that are involved in the planar cell polarity pathway. Functional inhibition of planar cell polarity signalling resulted in a reduction in anterior fin size, confirming that this pathway is a major contributor to batoid fin morphology. We also identified a fin-specific enhancer that interacts with several hoxa genes, consistent with the redeployment of hox gene expression in anterior pectoral fins, and confirmed its potential to activate transcription in the anterior fin using zebrafish reporter assays. Our findings underscore the central role of genome reorganization and regulatory variation in the evolution of phenotypes, shedding light on the molecular origin of an enigmatic trait.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Antisolvent‐Mediated Air Quench for High‐Efficiency Air‐Processed Carbon‐Based Planar Perovskite Solar Cells

Perovskite solar cells (PSCs) have becoma a leading low‐cost photovoltaic technology, achieving power conversion efficiencies (PCEs) of up to 26.1%. However, their commercialization is hindered by stability issues and the need for controlled processing environments. Carbon‐electrode‐based PSCs (C‐PSCs) offer enhanced stability and cost‐effectiveness compared to traditional metal‐electrode PSCs, i.e., Au and Ag. However, processing challenges persist, particularly in air conditions where moisture sensitivity poses a significant hurdle. Herein, a novel air processing technique is presented for planar C‐PSCs that incorporates antisolvent vapors, such as chlorobenzene, into a controlled air‐quenching process. This method effectively mitigates moisture‐induced instability, resulting in champion PCEs exceeding 20% and robust stability under ambient conditions. The approach retains 80% of initial efficiency after 30 h of operation at maximum power point without encapsulation. This antisolvent‐mediated air‐quenching technique represents a significant advancement in the scalable production of C‐PSCs, paving the way for future large‐scale deployment.

14 SOLAR ENERGY↗
DOE OSTI2022

Performance of Lithium-Ion Batteries with 3D Printed Anodes and Compressible Carbon Structures

Carbon scaffolds have been shown to improve the performance of Li metal anodes in Li-ion batteries by acting as conductive hosts for Li metal plating and stripping. The scaffolds provide a more uniform electric field, and their 3D geometry enables smaller diffusion paths for the Li ions. In this project, several different types of carbon lattices were 3D printed, mechanically tested, and analyzed in coin cells. Planar and 3D printed graphite coatings were evaluated as the baseline, since graphite is a common anode material. The results showed that implementing a 3D graphite lattice into a coin cell improved the Li plating and stripping efficiency compared to the planar coating. However, since graphite can intercalate Li ions, other carbon materials were also explored that should act as better hosts for Li plating/stripping. To improve the compressibility of these non-graphite carbon scaffolds, five different carbon ink formulations were 3D printed in lattice configurations. SEM imaging and compression testing showed that both the final dimensions and the compressibility of the carbon lattices depended on the type of carbon precursors used. The two most suitable compositions were found to be those made with graphene oxide-resorcinol formaldehyde and graphene oxide-ammonium hydroxide. In the future, these formulations will be further refined to increase their mechanical strength, and their performance as scaffold hosts for Li metal anodes will be evaluated in coin cells.

25 ENERGY STORAGE↗
DOE OSTI2026

Low-cost, Highly Efficient and Fast Thermally Pressed Scalable Carbon-based Planar Perovskite Solar Cells

This Final Technical Report summarizes work completed under Award Number DEEE0009833, titled "Low-cost, Highly Efficient and Fast Thermally Pressed Scalable Carbon-based Planar Perovskite Solar Cells." The project addressed the central technical problem that carbon-electrode perovskite solar cells (C-PSCs) can reduce electrode costs and improve environmental durability, but they have historically lagged noble-metalcontact devices due to poor carbon/perovskite contact, high carbon-electrode resistance, imperfect hole extraction, and insufficient operational stability. The Statement of Project Objectives (SOPO), therefore, required systematic engineering of thermally pressed carbon-based planar perovskite solar cells by improving the carbon/perovskite interface quality, improving carbon-electrode conductivity, and further increasing device stability. The work advanced understanding of carbon-based perovskite photovoltaics by connecting device performance to three coupled mechanisms: interfacial recombination at the perovskite/hole-transport-layer/carbon stack; lateral and vertical transport losses in carbon contacts; and instability driven by moisture, heat, illumination, ion migration, and slow/variable manufacturing steps.

14 SOLAR ENERGY↗
DOE OSTI2024

Inkjet-printed SnO x as an effective electron transport layer for planar perovskite solar cells and the effect of Cu doping

Inkjet printing is a more sustainable and scalable fabrication method than spin coating for producing perovskite solar cells (PSCs). Although spin-coated SnO 2 has been intensively studied as an effective electron transport layer (ETL) for PSCs, inkjet-printed SnO 2 ETLs have not been widely reported. Here, we fabricated inkjet-printed, solution-processed SnO x ETLs for planar PSCs. A champion efficiency of 17.55% was achieved for the cell using a low-temperature processed SnO x ETL. The low-temperature SnO x exhibited an amorphous structure and outperformed high-temperature crystalline SnO 2 . The improved performance was attributed to enhanced charge extraction and transport and suppressed charge recombination at ETL/perovskite interfaces, which originated from enhanced electrical and optical properties of SnO x , improved perovskite film quality, and well-matched energy level alignment between the SnO x ETL and the perovskite layer. Furthermore, SnO x was doped with Cu. Cu doping increased surface oxygen defects and upshifted energy levels of SnO x , leading to reduced device performance. A tunable hysteresis was observed for PSCs with Cu-doped SnO x ETLs, decreasing at first and turning into inverted hysteresis afterwards with increasing Cu doping level. This tunable hysteresis was related to the interplay between charge/ion accumulation and recombination at ETL/perovskite interfaces in the case of electron extraction barriers.

14 SOLAR ENERGY↗
DOE OSTI2023

24% Single-Junction GaAs Solar Cell Grown Directly on Growth-Planarized Facets Using Hydride Vapor Phase Epitaxy

A 24%-efficient single-junction GaAs solar cell grown directly on a faceted, spalled (100) GaAs substrate after in situ planarization growth by hydride vapor phase epitaxy (HVPE) is achieved. Controlled spalling, a promising low-cost substrate reuse technique, produces large facets in (100)-oriented GaAs substrates due to the orientation of the fracture planes used for lift-off. Planarization by HVPE offers a path toward direct use of these spalled substrates without costly polishing steps. In this report the growth rate anisotropy enabling planarization arising from diffusion and differences in the adsorption of growth species on {n11}B-type facets relative to (100) is determined. Consecutive planarization and device growth that results in a solar cell with a minimal performance difference relative to a control cell grown on an epitaxy-ready substrate are demonstrated. These results show that controlled spalling coupled with HVPE planarization is a viable pathway for lowering the cost of III-V photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2021

Optimization of four terminal rear heterojunction GaAs on Si interdigitated back contact tandem solar cells

High-efficiency, four-terminal tandem solar cells composed of thin GaAs films mechanically stacked onto interdigitated back contact silicon solar cells with a glass interlayer are demonstrated. The optimal thickness of the absorber layer of a rear heterojunction GaAs subcell for use in four terminal tandem solar cells was studied. GaAs top cells with absorber layer thicknesses of 1.5, 1.9, 2.3, 2.8, and 3.5 µm were fabricated on glass and mechanically stacked onto interdigitated back-contact Si bottom cells. All tandem cells were found to have efficiencies above 30% under the AM1.5 G spectrum demonstrating a relatively weak sensitivity to thickness in the four-terminal configuration. We found the 2.8 µm absorber layer cell to have the highest top cell and tandem cell efficiency at 26.38% and 32.57%, respectively. Optical modeling with transfer matrix method for the planar top cell and Lambertian light trapping in the textured Si subcell, along with drift-diffusion Hovel equations, were used to show photon recycling enhancement to the effective diffusion length and VOC of the top cell as a result of the low-index glass interlayer.

14 SOLAR ENERGY↗
DOE OSTI2026

Universal Relationship between Limiting Current and Electrochemical Transport Properties in Malonate-Based Polymer Electrolytes

There is considerable interest in developing high-performance electrolytes for rechargeable lithium batteries. For practical applications, the electrolyte must support large dc currents. However, the parameters most often reported in the literature, conductivity, κ, and current fraction, ρ + , reflect ion transport in the limit of infinitesimal currents. In this limit, the efficacy of an electrolyte is given by the product κρ + . The limiting current density, i lim , is the maximum current density that can be applied across an electrolyte; the cell voltage diverges if the applied current density exceeds ilim. This parameter reflects ion transport in the limit of large dc currents and is therefore of practical interest. It would therefore be convenient if i lim could be predicted from measurements of κρ + . In order to explore this possibility, we studied six malonate-based polymers and PEO at a fixed salt concentration (r = 0.08) and temperature (90°C) using symmetric cells with planar electrodes. Unfortunately, there is no correlation between ilim and κρ + . When the applied current density, i, is less than ilim, the cell voltage approaches a stable plateau, ϕ plateau . Here, we found a linear dependence between i and thickness-normalized plateau potential, ϕ plateau L –1 , irrespective of the magnitude of the applied current. In all seven polymer electrolytes, we found a linear correlation between ilim and the slopes of these lines, σ. In other words, measurements of σ can be used to predict the limiting current.

Jana, Rounak [Lawrence Berkeley National Laborator↗
DOE OSTI2021

Optimizing Vertical Crystallization for Efficient Perovskite Solar Cells by Buried Composite Layers

Planar-heterojunction perovskite solar cells (PSCs) have experienced rapid evolution in recent years because of the low-temperature processing, suitable alignment, and high mobility of the tin oxide buried contact layer. However, improper SnO 2 surface states and poor crystallinity of the top perovskite films are still the main obstacles for the planar PSCs in which performance always lags behind their mesoporous counterparts. Herein, a new buried contact is reported by introducing graphitic carbon nitride (g-C 3 N 4 ) into the commonly used SnO 2 which performs outstanding transmittance, conductivity, and surface states for a high-quality electron-transporting layer. Moreover, the vertical composition and crystallinity of the top perovskite film are manipulated by rich amino groups on the edge of the g-C 3 N 4 nanosheets which induce the prenucleation of the lead-rich species at the buried interface. Benefiting from the high-quality buried contacts and the optimized perovskite layers, the resultant PSCs achieve a champion efficiency of 21.5% with all photovoltaic parameters enhanced in comparison with their control counterparts (<20%).

planar-heterojunction perovskite solar cells↗
DOE OSTI2021

High spatial resolution temperature profile measurements of solid-oxide fuel cells

Temperature gradients resulting from local electrochemical reactions, current distribution and geometry of gas flow channels in solid oxide fuel cells (SOFCs) create thermal stresses, localized thermophysical property gradients and uneven property evolution, contributing to SOFC degradation. This paper presents a new method to perform temperature measurements (up to 800°C) at high spatial resolutions to monitor the operation of SOFCs. Using femtosecond laser irradiation, distributed fiber sensors were hardened for high temperature environment applications. Distributed fiber sensors were embedded in interconnected plates using an additive manufacturing method to perform temperature measurements with 4-mm spatial resolution during the operation of a planar fuel cell. The measurement revealed the impact of various H 2 fuel concentrations and current loads have on temperature profiles of the SOFC tested. Temperature variation on the anode side was found to be less than 5°C, and 3°C on the cathode side. The measurements were compared to results from a multiphysics fuel cell performance model simulating similar conditions. These simulations predicted similar temperature gradients, indicating the experimental data obtained is reasonable. The model also predicts that the effect of the embedded sensor has on the local temperature will be minimal and that the gradient of temperature in the gas channels will be captured despite the separation between the sensor and the gas flow. Finally, the high spatial resolution data harnessed by these distributed fiber sensors provides experimental support for model-based design and optimization to improve the operational efficiency and longevity of solid oxide fuel cells and fuel cell assemblies.

25 ENERGY STORAGE↗