Effect of neutrals on the anomalous edge plasma transport
Not Available
Zhang, Yanzeng (ORCID:0000000218562701)↗
SEARCH · Search NASA
Results for “plasma and neutral transport”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Simulation of plasma and neutral transport in PISCES-RF using SOLPS-ITER
In this research, the fluid plasma transport code SOLPS-ITER is applied and validated against experimental data from the plasma interaction surface component experimental station (PISCES)-RF linear plasma device to establish a physics basis for plasma and neutral transport in its two magnetic field (B-field) geometry setups-(1)the cusp and (2) non-cusp or linear B-field. The main focus of this study is to understand (1) radial plasma transport (2) heat and particle loads on the upstream dump and downstream target plate, and (3) the physics of plasma-neutral interactions in PISCES-RF. The simulation setup adheres to typical PISCES-RF experimental conditions, with a 2D helicon power deposition profile as an input heating source. SOLPS-ITER simulations reproduce experimental conditions with the Bohm diffusion model for both B-field configurations of the PISCES-RF experiment. Major energy loss channels include neutral radiation and power deposited on the wall and dump plate, with only 1% of the input power reaching the target. The ionization front is well confined near the dump plate due to the heating and puffing regions. Additionally, SOLPS-ITER simulation results are also found to be in very good agreement with the particle-in-cell calculations using the code-PICOS++ which supports the validity of SOLPS in low collisionality regime.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Challenges and approaches to interpretive modeling of boundary plasma and neutral transport in a closed, pumped divertor
An experimental discharge from the DIII-D tokamak is modeled using the SOLPS-ITER code suite and compared against measurements in the pumped and relatively closed upper divertor. Uncertainties of boundary plasma simulations are identified by attempting to match code inputs to experimental conditions, including iteratively solving transport coefficients to match upstream experimental profiles using varying quantities of core particle flux, different pumping models, and various assumptions of ion thermal transport. Simulated boundary conditions for particle injection at the core interface are shown to be relevant to the plasma solution at the divertor targets, even if upstream transport is modified so that plasma profiles are comparatively similar, although seperatrix density is not held constant. When upstream plasma profiles are matched to experimental measurements by varying diffusive transport coefficients, using either poloidally symmetric or ballooning structure, the model finds a majority of injected energy being transported radially off the computational domain, in conflict with experimental radiated power measurements and heat flux measurements at the divertor target. Imposing a maximum thermal diffusivity or radially shifting the experimental separatrix location of the fitted profiles to increase power conducted to the targets by increasing the upstream electron temperature does not significantly modify this result. Including a thermalizing plenum volume in the simulation domain is shown to maintain the experimental volumetric pumping rate without knowing the neutral energy distribution incident on the pump duct a priori. By modifying transport parameters to match different assumptions for ion temperature, downstream neutral pressure changes by more than a factor of two, suggesting that attention to ion thermal transport may be a critical parameter for simulations to accurately resolve recycling and neutral transport, particularly in a closed divertor geometry. In addition to quantifying various modeling uncertainties, this work motivates both further experimental study and modeling improvements to improve predictive capabilities.
divertor↗
Machine Learning Approach to Modeling of Neutral Particles Transport in Plasma
A propagator‐based approach is investigated for Monte‐Carlo (MC) modeling of neutral particle transport in fusion boundary plasmas. The propagator is based on a Green's function for the neutral kinetic equation, which depends on the plasma profiles. A neural network (NN)‐based model for the propagator provides a fast and accurate solution for the neutral distribution function in plasma. Preliminary results from a small 1D test problem look encouraging. The proposed approach, a propagator‐based NN model for neutral transport in plasma, has potential for generalization to higher dimensions and efficient coupling with plasma models.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
1D model of tokamak scrape-off layer and divertor plasmas: Dimensionless parameters and the results of numerical simulations
Solutions of a 1D model of the scrape-off layer and a divertor plasma in a tokamak are analyzed on the basis of dimensionless parameters governing the physics of both plasma and neutral transport and atomic physics processes. Numerical simulations based on fluid plasma and Monte Carlo neutral modeling confirm earlier results obtained with simplified analytic considerations and numerical simulations performed with fluid neutral description and demonstrate bifurcation of plasma parameters. Further, these simulations also confirm that the major physical reasons for the rollover of the plasma flux to the target, which is the key feature of the phenomenon of divertor plasma detachment, are the impurity radiation loss and plasma recombination. It is suggested that simulations of the edge plasma based on dimensionless parameters provide a powerful tool for checking the consistency of the physics incorporated in existing complex 2D codes used for edge plasma modeling.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Modeling of particle transport, neutrals and radiation in magnetically-confined plasmas with Aurora
In this work, we present Aurora, an open-source package for particle transport, neutrals and radiation modeling in magnetic confinement fusion plasmas. Aurora's modern multi-language interface enables simulations of 1.5D impurity transport within high-performance computing frameworks, particularly for the inference of particle transport coefficients. A user-friendly Python library allows simple interaction with atomic rates from the Atomic Data and Atomic Structure database as well as other sources. This enables a range of radiation predictions, both for power balance and spectroscopic analysis. We discuss here the superstaging approximation for complex ions, as a way to group charge states and reduce computational cost, demonstrating its wide applicability within the Aurora forward model and beyond. Aurora also facilitates neutral particle analysis, both from experimental spectroscopic data and other simulation codes. Leveraging Aurora's capabilities to interface SOLPS-ITER results, we demonstrate that charge exchange is unlikely to affect the total radiated power from the ITER core during high performance operation. Finally, we describe the ImpRad module in the one modeling framework for integrated task framework, developed to enable experimental analysis and transport inferences on multiple devices using Aurora.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Analysing the effects of heating and gas puffing in Proto-MPEX helicon and auxiliary heated plasmas
The Material Plasma Exposure Experiment (MPEX) is being constructed at Oak Ridge National Laboratory to investigate critical fusion reactor issues, such as plasma–material interactions (PMIs) under reactor-relevant conditions and time scales. The linear device Proto-MPEX was used as a test bed to address anticipated research and development issues associated with heating scenarios and establish the physics basis for MPEX. The SOLPS-ITER code suite has been applied to understand plasma and neutral transport in Proto-MPEX and to increase confidence in predictive simulations for MPEX. Coupling between COMSOL and SOLPS is performed to implement a 2D electron heating profile of the helicon source. The simulations show reasonable agreement with the experimental data for plasma with helicon and auxiliary electron cyclotron heating (ECH). Both Bohm and constant diffusion (D$_\perp$: 0.5 m 2 s –1 and $\chi_\perp$: 1 m 2 s –1 ) simulations show similar levels of agreement with respect to the sparse experimental data available, assuming a few per cent impurity concentration. ECH significantly increases the target electron temperature, however, the target electron density is reduced compared to helicon-only heated plasmas due to an increase in flow velocity and radial losses. The simulations show that further increasing the ECH power results in an increase in the target electron density due to increased recycling flux and ionization. The results indicate that ECH significantly enhances the target heat flux, with ECH power of 50 kW increasing the target heat flux from 0.4 to 17 MW m –2 . It is found that a small amount of gas puffing (GP) near the target plate can further increase the target heat fluxes at the higher ECH power cases, but the target heat flux is reduced at higher GP conditions due to a significant reduction in electron temperature via radiation. ECH and GP scenarios can generate a higher target flux, facilitating improved PMI studies with more reactor-relevant plasma conditions.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
On the role of ion temperature gradient turbulence in driving ion thermal transport in neutral beam injection-heated L-mode plasmas in a superconducting tokamak
In this paper, we report a detailed experimental study of the role of ion-temperature-gradient driven turbulence in driving ion thermal transport in neutral beam injection (NBI)-heated L-mode plasmas in Experimental Advanced Superconducting Tokamak (EAST) (Wan et al 2000 Nucl. Fusion 40 1057) coupled with linear and nonlinear gyrokinetic simulations. Significant ion-scale turbulence k ⟂ < cm −1 (k ⟂ < 1.5, where k ⟂ where is the perpendicular wavenumber and ρ s is the ion gyroradius calculated using local electron temperature T e ), measured with a microwave reflectometer, is observed in the plasma core at for r/a ≈ 0.265 and 0.5 (where r is half the diameter of the closed flux surface at a given radial position, and a is half the diameter of the last closed flux surface). Local linear stability analysis with experimental equilibrium quantities at these two radial locations using the GS2 gyrokinetic code shows that the most unstable ion-scale micro-instability is the ion temperature gradient (ITG) mode. Since the computed maximum ion-scale linear growth rates are larger than the local Waltz-Miller E × B shearing rate (Waltz and Miller 1999 Phys. Plasmas 6 4265), the E × B shear is unable to suppress ion-scale turbulence, consistent with the experimental observation of ion-scale turbulence. Experimental ion and electron thermal transports, calculated with power balance analysis, are both anomalous with ion thermal transport being the dominant channel. Nonlinear gyrokinetic simulations using the electrostatic global particle-in-cell gyrokinetic tokamak simulation (GTS) code (Weixing Wang et al 2010 Phys. Plasmas 17 072511) show good quantitative agreement between predicted ion thermal transport and that from the power balance analysis. These results demonstrate for the first time the important role of ITG turbulence in driving thermal transport in NBI-heated L-mode plasmas in EAST, showing the effectiveness of GTS code in simulating electrostatic turbulence in EAST and the need of suppressing ITG turbulence to improve energy confinement in EAST.
Sun, P. J. [Chinese Academy of Sciences (CAS), Hef↗
Self-consistent modeling of tokamak edge plasma transport with lithium sources
Magnetic confinement fusion devices require effective heat and particle exhaust solutions on the divertor plates to operate sustainably, especially under reactor-relevant conditions. Liquid lithium divertors have been proposed to address two major challenges: control of excessive heat flux to plasma-facing components through vapor shielding and minimization of core plasma contamination from impurities. The National Spherical Torus Experiment-Upgrade (NSTX-U) will explore lithium as a divertor material due to its potential to meet both objectives. We present a self-consistent coupling framework between the plasma boundary transport code UEDGE and the lithium wall transport code Wall–Li to evaluate the feasibility and operational limits of lithium-based divertors. The model aims to optimize lithium sourcing levels to prevent core plasma contamination via fuel dilution while ensuring divertor protection through vapor shielding. This integrated framework, applicable to any tokamak with lithium sources, dynamically adjusts lithium sourcing based on local plasma conditions and surface temperature. The coupled model is tested using NSTX-like geometry and plasma conditions to assess its performance and reliability. Wall–Li calculates lithium fluxes from plasma-facing components, incorporating physical sputtering, thermally enhanced sputtering, and evaporation driven by surface temperature and ion flux. These fluxes are reintroduced into UEDGE as neutral lithium atoms, enabling simulation of their transport and distribution within the plasma. UEDGE computes plasma and neutral transport, surface heat flux, and iteratively feeds this information back to Wall–Li. A small time step is employed to ensure numerical stability and convergence, enabling accurate simulations over typical tokamak discharge durations. This integrated modeling approach provides a robust tool for identifying operational regimes that balance effective lithium sourcing with minimal core plasma contamination, offering critical insights for optimizing lithium-based divertor systems in current and future fusion devices.
Magnetic confinement fusion↗
Simulation of Liquid Lithium Divertor Geometry Using SOLPS-ITER
Here, plasma-facing component (PFC) geometries are evaluated for a Fusion Nuclear Science Facility (FNSF) design to find solutions that are compatible with flowing liquid lithium components while satisfying requirements from the perspective of plasma and neutral particle transport. Flowing liquid metal (LM) divertor systems offer important advantages due to continual regeneration of the surface material, but may require modifications from standard optimized tokamak divertor designs. Scrape Off Layer Plasma Simulator for the International Thermonuclear Experimental Reactor (SOLPS-ITER) simulations are used to compare standard vertical target, open, and balanced baffled geometries. It is found that the open geometry offers little control of neutral particles and has narrow operating windows where the divertor fluxes can be lowered to acceptable levels, while maintaining the required upstream density. The addition of neutral baffles allows greater control over the divertor conditions with less impact on the upstream density. The divertor neutral pressure in the baffled geometry is slightly higher than the open divertor, but not as large with a vertical target. A first-pass coupling of the SOLPS solution with sheath and implantation/erosion models to compute the lithium emission shows that the lithium is largely confined to the near-surface region due to the small ionization mean free path and large main ion flow toward the surface. The lithium source was varied by three orders of magnitude. At the highest rate, when the sourced lithium approaches the level of the main ion recycling flux, a high core lithium concentration (~10%) is observed with only moderate power dissipation to affect the divertor plasma.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Reconstruction and interpretation of ionization asymmetry in magnetic confinement via synthetic diagnostics
Abstract Strong poloidal refueling asymmetry in the DIII-D tokamak is inferred from line radiation measurements. Synthetic diagnostics in neutral transport modeling coupled to gyrokinetic simulations illuminate implications for the plasma flow profile in the scrape-off layer of single-null beam-driven discharges. Recycling occurs primarily either on the inner or outer divertor legs, depending on the toroidal magnetic field direction. By reversing the toroidal magnetic field, the observed line radiation asymmetry is nearly eliminated or reversed. It is determined that, while relatively simple physics can describe the observed ionization asymmetry, predicting the overall brightness of the hydrogenic Lyman- α signal requires detailed simulation of the plasma and resulting turbulence. To this end, kinetic plasma simulations fully coupled to comprehensive neutral transport calculations—a novel capability—provide first-principles reproduction of Lyman- α observations on DIII-D.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Role of Neutrals Versus Transport in Determining the Pedestal Density Structure: Final Technical Report
In fusion devices the plasma density plays a crucial role in determining the fusion reaction rate and has a direct impact on the fusion gain of a given device. This density is in general regulated by the particle sources and transport near the plasma edge, which give rise to an edge density pedestal. When predicting the performance of future devices, this density pedestal is often prescribed, rather than predicted, due to a lack of models which allow confident extrapolation. This project aims to advance these models through the focused validation of theoretical models related to the transport of fueling neutral particles, and through interpretive transport modeling in present day fusion plasmas, in which the penetration of neutrals is altered to better simulate future reactor-like conditions. Achievements in theory and model validation under this project have advanced our understanding of how much of the edge density profile is set by transport versus direct ionization, enabling interesting projections to future burning plasma devices.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Plasma Wall Interaction with 3-D Plasma Boundaries
The interaction of the edge plasma and the material surfaces is one of the most critical challenges on the path to harness fusion power as new, fundamental energy source. This challenge typically combines the thrust to reach high density, low temperature (detached) plasmas in front of the divertor target plates as well as understanding the plasma material interaction (PMI) in particular in this regime. The combination of both research thrusts represents an extraordinarily challenging subject encompassing spatial scales spanning nanometers to meters in all states of matter and across a broad energy range. Modeling capabilities, which help to interpret data from nowadays experiments and enable extrapolation to future devices are urgently required. This is in particular true for toroidal magnetic confinement devices with three-dimensional (3D) plasma boundaries. Such plasma boundary geometries occur in tokamaks, when small amplitude magnetic perturbations are used to stabilize the unruly edge plasma or in stellarators, that are inherently 3D plasma confinement devices. In this project, the impact of 3D plasma boundaries on the plasma material interaction (PMI) was assessed. This work focused on plasma boundary conditions, in which high-density conditions at the material surfaces yield mitigation of the otherwise immense heat and particle loads that these materials would see. These so-called high recycling and eventually detached plasma regimes are of great interest for future reactor operation. In the project, key features that are unique to 3D boundaries were explored in comparison to canonically assumed axisymmetric plasma edge situations in tokamaks. In particular, the relevance of the 3D boundary situation in the extrapolation to the plasma boundary solution at ITER, the next step fusion energy experiment under construction as a multi-national, world-wide large-science experiment in southern France, has been explored. The EMC3-EIRENE plasma edge fluid and kinetic neutral transport code has been advanced to cope with the challenging and unprecedented conditions in the ITER boundary plasma including 3D fields that are planned to be used to suppress harmful edge instabilities, the so-called edge localized modes. This is a vital integration challenge for ITER and the results from this grant have provide a leading capability for this assessment. It was shown that the detachment process in a 3D edge solution for ITER follows the recycling regimes that are known from axisymmetric solutions, but that multiple plasma exhaust channels connected to the material surfaces are established which feature individual recycling characteristics. Because these channels touch the material surfaces in the divertor in a 3D geometry, the compatibility with the plasma material interaction (PMI), including erosion and impurity generation has been found to be an important part of the integration challenge. To address this, the fully 3D plasma material interaction code ERO2 has been adapted to these ITER specific geometries and a homogeneous mixing model was implemented, that allows to consider the mixing of Be and Was used at ITER in the PMI modeling. This model enhancement has been used to study non-local migration of Be in the JET ITER like wall configuration and it has been shown that with this model such complex migration processes in ITER relevant plasma shapes and with ITER relevant plasma boundary conditions can be addressed. The combined modeling approach using EMC3-EIRENE as a plasma boundary transport code and the ERO2 specialized PMI model will be an asset for the continued preparations of ITER operation as well as for Fusion Pilot Plant efforts that have emerged in the U.S. during the evolution of this grant. The predictive capability of this numerical tool has been validated at the DIII-D US national fusion facility. Here, dedicated plasma edge diagnostics were implemented to measure the impurity household around a 3D edge plasma during ELM suppression by 3D fields. Dedicated experiments with local material probes using these diagnostics and the state-of-the-art suite of boundary measurements at DIII-D have shown that the 3D perturbation of the plasma edge that is excreted by such 3D control fields yield a perturbation of the plasma boundary flux structure and hence also of the resulting PMI. The 3D boundary plasma is composed out of helical magnetic flux channels that intersect the divertor targets at an angle relative to the main guiding field, i.e., the toroidal magnetic field component of the tokamak. A similar effect has been measured as well on limiter surfaces during the startup campaign at the new stellarator experiment Wendelstein 7-X. These experiments ad initial analysis with the ERO plasma material interaction model, suggested that the place of erosion for a given particle from the surface and its re-deposition can be different in such 3D field geometries yielding potentially a significant level of net-erosion. This is not the case for axisymmetric solutions, where it was shown in the past that the eroded particles are effectively re-deposited into gaps produced by erosion at the same position and hence the net-erosion levels are small. For ITER, the quest to suppress the ELMs and at the same time maintain the integrity of the divertor is an issue, which these fundamental findings will help to resolve. The coupling of this work to the extrapolation in the ITER program has been addressed by both the PI and the lead numerical scientist being ITER Science Fellows in the duration of the contract and forward. A second focus in the exploration of 3D boundary effects on tokamaks and stellarators has been set on the measurement of helium exhaust features with such 3D fields. This is important because He represents the ash of the fusion process and needs to be exhausted. It was shown that 3D field application compatible with suppression of ELMs yields an increase of the helium exhaust performance. The ratio of the effective helium confinement time over the energy confinement time was reduced by almost 50% which demonstrated that the impact of helium accumulation in the plasma core with respect to the confinement of energy to sustain the fusion reaction is significantly improved with such 3D control fields. It was shown that this is the case for tokamaks as well as stellarators. At the Large helical Device in Japan, a similar enhancement of the helium exhaust features when small amplitude additional 3D fields were applied was measured. This is an important additional function of 3D field application and its impact on ITER is presently being studied in combination with investigations of helium exhaust in 3D field geometries of stellarator devices.
3D plasma edge transport↗
Demonstration of OpenMC as a framework for atomic transport and plasma interaction
Modern tooling is demanded for predicting the transport and reaction characteristics of atoms and molecules, especially in the context of magnetic confinement fusion. DEGAS2, among the most common and capable tools currently in use, shares many fundamental similarities with the OpenMC framework, which was primarily developed for neutron and photon transport. In this work, we demonstrate that OpenMC is suitable for atomic transport calculations. The relative error between the models is small, and the performance of OpenMC is at least comparable to DEGAS2. This is the case even without taking advantage of heterogeneous computing architecture, which is only one of the several remarkable new capabilities that this demonstration heralds.
Monte Carlo↗
Laser-induced-fluorescence imaging of a spin-polarized ultracold neutral plasma in a magnetic field
In this work, we report Doppler-sensitive laser-induced-fluorescence (LIF) imaging of an ultracold neutral plasma in a magnetic field. Local values of ion density, hydrodynamic fluid velocity, temperature, and spin polarization are obtained using a fluorescence model based on velocity-resolved rate equations (REs) including the transfer of ions between states due to laser coupling and spontaneous emission. The RE approach captures optical pumping of ions into states that are not driven by the LIF excitation laser, and this is validated with experimental data. Combined molecular-dynamics and quantum-trajectories simulations verify that velocity-changing collisions have a negligible impact on the state population evolution for typical experimental conditions. Relative intensities of Zeeman components of the LIF spectra provide clear evidence that the ions are electron-spin-polarized when created by photoionization of magnetically trapped 88 Sr atoms. This probe opens many possibilities for studying thermal transport and the equilibration of neutral plasmas in overlapping regimes of strong coupling and magnetization.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Periodic Narrowband Radio Wave Emissions and Inward Plasma Transport at Saturn's Magnetosphere
The abrupt brightening of an Energetic Neutral Atom (ENA) blob or cloud has been interpreted as plasma injection in the Kronian magnetosphere (termed ENA injection herein). Morphologically, there appears to be two types of abrupt ENA cloud brightening: (1) the brightening of a large cloud usually seen at distances >10–12 R {sub s} (R {sub s} ∼ 60,268 km) in the midnight or postmidnight region; (2) the brightening of a smaller cloud usually seen at distances <10–12 R {sub s} around 21–03 magnetic local time. Among many radio waves observed at Saturn, type 2 ENA injections correlate best with the 5 kHz narrowband (NB) waves. Using Cassini Ion and Neutral Camera (INCA) and Radio and Plasma Wave Science (RPWS) data, we examine the periodicities of the type 2 ENA injections and the 5 kHz NB emissions as well as their cross-correlations, which have been previously used to measure the lag times or phase differences. Because correlational analysis can only establish linear relationships, we also use mutual information to establish linear and nonlinear relationships. On average, the peak of the 5 kHz NB emission lags those of the type 2 ENA injection by about a few minutes to 2 hr. The injection of hot plasma to the inner magnetosphere can lead to temperature anisotropy, which can generate electrostatic upper hybrid waves, which upon encountering the high-density gradient at the outer edge of the Enceladus density torus, can mode convert to Z mode and then to O mode. The 5 kHz NB waves commonly propagate in the O mode.
79 ASTRONOMY AND ASTROPHYSICS↗
Time-dependent modeling of coupled plasma-wall dynamics
Effects of dynamic wall outgassing on divertor plasma during an ELM-like heat pulse are modelled using newly coupled edge plasma code UEDGE and all reaction-diffusion code FACE. Different divertor regimes are simulated depending on the degree of the plasma detachment. It is shown that hydrogen outgassing from the divertor target plate induced by ELM pulse in the semi-detached regime can trigger deep plasma detachment. The induced detachment does not spontaneously reverse after the pulse due to ineffective implantation of low energy plasma hydrogen in the target material. Furthermore, we demonstrate that plasma neutrals play essential role in heat transport in a detached divertor. The modelled hydrogen dynamics in the wall material demonstrates that the heat pulse leads to enhanced hydrogen transport toward the wall bulk.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗