Search NASA⌕ Search

SEARCH · Search NASA

Results for “plasma antenna”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Experimental studies of plasma-antenna coupling with the JET Alfvén Eigenmode Active Diagnostic

Here, this paper presents a dedicated study of plasma-antenna (PA) coupling with the Alfvén Eigenmode Active Diagnostic (AEAD) in JET. Stable AEs and their resonant frequencies f, damping rates γ < 0, and toroidal mode numbers n are measured for various PA separations and limiter versus X-point magnetic configurations. Two stable AEs are observed to be resonantly excited at distinct low and high frequencies in limiter plasmas. The values of f and n do not vary with PA separation. However, |γ| increases with PA separation for the low-f, but not high-f, mode, yet this may be due to slightly different edge conditions. The high-f AE is detected throughout the transition from limiter to X-point configuration, though its damping rate increases; the low-f mode, on the other hand, becomes unidentifiable. The linear, resistive MHD code CASTOR is used to simulate the frequency scan of an AEAD-like external antenna. For the limiter pulses, the high-f mode is determined to be an n = 0 GAE, while the low-f mode is likely an n = 2 TAE. During the transition from limiter to X-point configuration, CASTOR indicates that n = 1 and 2 EAEs are excited in the edge gap. These results extend previous experimental studies in JET and Alcator C-Mod; validate the computational work performed by Dvornova et al; and provide guidance for the optimization of PA coupling in upcoming JET energetic particle experiments, for which the AEAD will aim to identify the contribution of alpha particles to AE drive during the DT campaign.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Experimental studies of plasma-antenna coupling with the JET Alfven Eigenmode Active Diagnostic

This paper presents a dedicated study of plasma-antenna (PA) coupling with the Alfven Eigenmode Active Diagnostic (AEAD) in JET. Stable AEs and their resonant frequencies f, damping rates gamma < 0, and toroidal mode numbers n are measured for various PA separations and limiter versus X-point magnetic configurations. Two stable AEs are observed to be resonantly excited at distinct low and high frequencies in limiter plasmas. The values of f and n do not vary with PA separation. However, |gamma| increases with PA separation for the low-f, but not high-f, mode, yet this may be due to slightly different edge conditions. The high-f AE is detected throughout the transition from limiter to X-point configuration, though its damping rate increases; the low-f mode, on the other hand, becomes unidentifiable. The linear resistive MHD code CASTOR is used to simulate the frequency scan of an AEAD-like external antenna. For the limiter pulses, the high-f mode is determined to be an n = 0 GAE, while the low-f mode is likely an n = 2 TAE. During the transition from limiter to X-point configuration, CASTOR indicates that n = 1 and 2 EAEs are excited in the edge gap. These results extend previous experimental studies in JET and Alcator C-Mod; validate the computational work performed by Dvornova et al 2020 Phys. Plasmas 27 012507; and provide guidance for the optimization of PA coupling in upcoming JET energetic particle experiments, for which the AEAD will aim to identify the contribution of alpha particles to AE drive during the DT campaign.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Investigation of Materials for Radio Frequency Antenna Plasma Facing Components

Here, the interaction of radio frequency (RF) sheaths with fusion reactor relevant materials (e.g., tungsten and titanium diboride) is being studied on the RF Plasma Interaction Experiment (RF PIE). The RF PIE consists of an electron cyclotron resonance (ECR) plasma source (2.45 GHz, 5 kW) with a biased and heated RF electrode that is used to simulate antenna surfaces in contact with the edge plasma. Helium plasmas (density of ~1e18/m 3 , electron temperature of 4–5 eV) are being used to explore sheath formation on material surfaces with biases up to 500 V. The erosion of a tungsten surface is being studied spectroscopically using a mirror-linked 1 m Czerny-Turner UV imaging spectrometer with a spectral resolution of 0.012 nm for measuring plasma emission in and near the sheath. Tungsten line emission intensity is higher for RF versus dc biasing for similar plasma conditions and average ion energy. RF biasing causes a broadening of the ion energy distribution function (IEDF) due to the RF sheath, as determined from the hPIC2 code, and results in enhanced sputtering. Calculations of the expected sputtering yield for dc and RF biasing are consistent with experimental observations of changes in the 400.9 nm tungsten line emission intensity as a function of ion energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Tin removal by an annular surface wave plasma antenna in an extreme ultraviolet lithography source

Tin contamination of the collector mirror surface remains one of the crucial issues of EUV (Extreme Ultraviolet) sources, directly impacting the availability of the tool. Hydrogen plasma-based tin removal processes employ hydrogen radicals and ions to interact with tin deposits to form gaseous tin hydride (SnH 4 ), which can be removed through pumping. An annular surface wave plasma (SWP) source developed at the University of Illinois—Urbana Champaign is integrated into the cone and perimeter of the collection mirror for in situ tin removal. The SWP is characterized by high ion and radical densities, low electron temperature, and local generation where etching is needed. This method has the potential to significantly reduce downtime and increase mirror lifetime. Radical probe measurements show hydrogen radical densities in the order of 10 19 m -3 , while Langmuir probe measurements show electron temperatures of up to 6 eV and plasma densities on the order of 10 17–18 m -3 . The generated ions are essential to the tin cleaning and have sufficiently low energy to cause no damage to the collector capping layer. Tin etch rates of up to 270 nm/min were observed in a variety of experimental conditions, including various powers, pressures, flowrates, and temperatures. In conclusion, the high etch rates demonstrated in this study exceed the expected contamination rate of the EUV source.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Automated design of an additive manufactured compact broadband antenna for plasma reflectometry

Broadband antennas operating in the gigahertz frequency range are regularly used for plasma reflectometry diagnostics. Due to a lack of space and unique diagnostic constraints, these antennas are often custom in design and frequency range. Recent advances in additive manufacturing of high temperature copper alloys allow for expanded freedom in design of these diagnostic antennas. In this work, a heuristic simulated annealing algorithm is used alongside 3-D finite element simulation to automate the design of a double ridged rectangular horn antenna for a reflectometry diagnostic on the DIII-D tokamak. Optimization of antenna performance given the design constraints results in a compact broadband (6-20+ GHz) antenna design. Measured transmission from the additively manufactured antenna matches simulation within reasonable error, and experimental plasma electron density profiles from the DIII-D high-field side scrape-off layer are shown.

Additive manufacturing↗
DOE OSTI2020

Overview of TAE technologies’ HHFW project on LAPD

Simulation survey performed at TAE Technologies, has demonstrated that high harmonic fast wave (HHFW) heating is a promising scenario to heat core electrons of FRC plasma. To prepare the proposed experimental study of HHFW antenna-plasma coupling and wave propagation on LAPD machine at UCLA, a high-power-capable 4-strap antenna has been calculated and designed through collaboration among TAE, ORNL, ASIPP, and UCLA. This antenna was mechanically designed and fabricated by ASIPP and it has been installed recently on LAPD. Meanwhile, by using the Petra-M code, a newly developed generic electromagnetic simulation tool for modeling RF wave propagation, the RF-SciDAC team starts 3D full wave simulations. Detailed information on antenna electromagnetic simulations and mechanical design, as well as preliminary experimental results of wave propagation study with the newly installed phased- array antenna, will be presented in this paper.REFE

Yang, Xiaokang↗
DOE OSTI2020

3D full wave fast wave modeling with realistic antenna geometry and SOL plasma

This paper reports the significant advancement of our ability to model and to understand how RF waves interact with the SOL plasma, by simulating the full torus 3D SOL plasma together with the antenna and core plasma. We introduce and use a recently developed and open source code, Petra-M, which was constructed on the scalable MFEM C++ finite element library, and performed 3D full wave simulations in the HHFW regime for both NSTX-U and LAPD plasmas. A first full wave simulation for a full 3D torus including a realistic antenna geometry and SOL plasma region for NSTX-U is presented. A scan of the antenna phasing shows a strong interaction between FWs and the SOL plasma for lower antenna phasing, which is consistent with previous NSTX HHFW observations. The effect of the 3D wave field on the fast ion population from NBI beams in NSTX-U is also discussed by using the 3D field obtained from the Petra-M simulations in the full-orbit following particle SPIRAL code. On LAPD, 3D full wave simulations of a new HHFW 4-strap antenna recently installed by TAE Technologies on LAPD are performed showing a qualitative agreement with experimental data.

Bertelli, Nicola↗
DOE OSTI2022

3D full wave fast wave modeling with realistic HHFW antenna geometry and SOL plasma in NSTX-U

This paper reports the significant advancement of our ability to model and to understand how RF waves interact with the SOL plasma, by developing for the full torus 3D scrape-off layer (SOL) plasma simulation together with the antenna and core plasma in the NSTX-U device in HHFW frequency regime for a cold plasma model. The present paper extends the previous modeling (Bertelli et al 2020 AIP Conf. Proc. 2254 030001) to a full 3D device geometry including realistic antenna geometry in order to capture a more realistic experimental situation including the fully 3D wave field effects and the antenna plasma interaction in the SOL plasma, and, at the same time, resulting core wave propagation. Here, the central tool of the present work is the Petra-M code, which is a newly developed state-of-the-art generic electromagnetic simulation tool for modeling RF wave propagation based on MFEM (http://mfem.org), an open source scalable C++ finite element method library.

3D RF modeling↗
DOE OSTI2025

Modeling of convective cells, turbulence, and transport induced by a radio-frequency antenna in the tokamak boundary plasma

The edge turbulence model Hermes (Dudson et al 2017 Plasma Phys. Control. Fusion 59 05401) is set up for plasma boundary simulations with an radiofrequency (RF) antenna, using parameters characteristic of a tokamak edge. Cartesian slab geometry is used with thin plate limiters representing the ion cyclotron range of frequency (ICRF) antenna side-wall limiters. Ad-hoc DC electric biasing of the limiters, motivated by calculations with VSim (Nieter et al 2004 J. Comput. Phys. 196 448), represents an induced RF sheath rectified potential in the plasma turbulence model. Flux-driven turbulence simulations demonstrate a realistic distribution of plasma profiles and fluctuations. There is a clear effect of the antenna sheath voltage leading to formation of convective cells; bias-induced convective transport flattens the scrape-off layer density profile and fluctuations penetrate into the shadow region of the limiters as the bias voltage increases. Turbulent transport for impurity ions is inferred by following ion trajectories in the simulated plasma turbulence fields, showing Bohm-like effective diffusion rates. All in all, the model elucidates the key physical phenomena governing the effects of ICRF-induced antenna biasing on the tokamak boundary plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Spatial decay of electromagnetic waves from hypervelocity impact plasmas

Due to the high kinetic energy of impactors in space, hypervelocity impacts on spacecraft can ablate spacecraft material and produce plasmas. These plasmas have been observed in ground-based experiments to produce electromagnetic pulses (EMPs) and are suspected to be a cause of spacecraft anomalies. The initial EMP that is produced after plasma formation is replicated using a 2D electromagnetic plasma simulation, consisting of a discontinuous Galerkin, particle-in-cell (DG-PIC) framework. The spontaneous formation of EMPs from an initial quasineutral plasma is consistent with previous works and show behavior similar to that of waves emitted by antennas. The EMP emits from the plasma with a frequency less than the plasma frequency associated with the point of maximum density, showing the importance of the density gradient, and the far-field region of the “plasma antenna” is estimated. From the proportionality between plasma frequency and EMP frequency, there is a direct correlation between plasma density and radiation. Finally, as the plasma density decreases, the EMP frequency decreases, which suggests that several observable phenomena, such as optical flashes, radio frequency emission, and microwave emission, all result from the same plasma-related mechanism within a single hypervelocity impact.

42 ENGINEERING↗
DOE OSTI2026

Modeling rf sheath formation in turbulent tokamak boundary plasma

During ICRF antenna operation, complex interactions between turbulent density profiles, nonlinear RF sheaths, and RF-induced convective transport are observed to alter plasma density in the tokamak edge [D’Ippolito et al., Nucl. Fusion 38, 1543 (1998)]. In this work, we explore the physics of such interactions via numerical modeling, using a nonlinear EM/plasma/sheath code (VSim) and profiles obtained from a fluid plasma turbulence code (Hermes) in a 3D slab domain containing biased side-wall limiters. RF-rectified sheath formation on antenna and limiter surfaces is observed as electromagnetic waves launched by the antenna are refracted through the turbulent density profile. On transport timescales, such sheath potentials have been shown to influence both the mean species density and its RMS fluctuation spectrum [Smithe et al., these proceedings]. On the faster RF timescales, we demonstrate that the converse is also true – regions of high plasma density near material surfaces give rise to the highest sheath potential amplitudes. When density is turbulent and spatially nonuniform, localized regions of high sheath potential (hotspots) may develop where high-density filaments intersect material surfaces. Such hotspots are of particular concern as sources of impurity sputtering, and we explore their behavior in response to changes both to the local plasma density and to antenna operating parameters and structure. Related results exploring the role of Faraday shields and/or enclosing structures in suppressing high sheath potentials for other devices (e.g. SPARC) will also be shown.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Role of electrostatic perturbation on kinetic resistive wall mode with application to spherical tokamak

Abstract A more complete non-perturbative magnetohydrodynamic (MHD)-kinetic hybrid formulation is developed by including the perturbed electrostatic potential δφ in the particle Lagrangian. The fluid-like counter-parts of the hybrid equations, in the Chew-Goldberger-Low high-frequency limit, are also derived and utilized to test the new toroidal implementation in the MARS-K code. Application of the updated non-perturbative hybrid model for a high- β spherical tokamak plasma in MAST finds that the perturbed electrostatic potential generally plays a minor role in the n = 1 ( n is the toroidal mode number) resistive wall mode instability. The effect of δφ is largely destabilizing, with the growth rate of the instability increased by several (up to 20) percent as compared to the case without including δφ . A similar relative change is also obtained for the kinetic-induced resonant field amplification effect at high- β in the MAST plasma considered. The updated capability of the MARS-K code allows quantitative exploration of drift kinetic effects on various MHD instabilities and the antenna-driven plasma response where the electrostatic perturbation, coupled to magnetic perturbations, may play important roles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Study of a linear surface wave plasma source for tin removal in an extreme ultraviolet source

Tin deposition mitigation employs hydrogen radicals and ions, formed in a hydrogen plasma, to interact with tin to form tin hydride (SnH 4 ) in the gaseous state, which is then pumped away. Surface wave plasma (SWP) technology developed at Illinois generates hydrogen radicals and ions, resulting in tin etch rates that are high enough to keep extreme ultraviolet (EUV) lithographic tools clean. An advantage of an SWP antenna is the ability to generate a high density of hydrogen radicals and hydrogen ions directly at the desired etching location. In situ etching of tin enables high availability EUV tools by maintaining high reflectivity of the multilayer mirror of the collector. Additionally, the SWP is characterized with low ion energies and low electron temperature, such that the multilayer mirror does not suffer any damage from sputtering or implantation of hydrogen ions during operation. Here, experiments elucidating the fundamental processes of tin removal are conducted by varying pressure, power, surface temperature, and gas flow rate in order to observe the etch rate behavior. Our results have shown that the presence of hydrogen ions increases etch rates because ion bombardment weakens Sn–Sn bonds, which, in turn, allows for a higher rate of chemical etching by the radicals. The ion bombardment reduces the number of radicals needed to etch a single tin atom to the range of 10 2 –10 3 . The linear SWP antenna yields plasma densities on the order of 10 17 to 10 18 m -3 and radical densities on the order of 10 18 to 10 19 m -3 , allowing for greater utilization of ion etch enhancement. Etch rates of up to 200 nm/min have been achieved. The surface temperature of the samples is an important factor in the etching process such that the decrease in the surface temperature increases the etch rates and decreases the hydrogen desorption rates. In addition, a kinetic etch model is developed to explain the behavior of etch rates as a function of surface temperature. Furthermore, results from experiments performed in an Illinois NXE:3100 chamber will be discussed.

42 ENGINEERING↗
DOE OSTI2021

Alpha particle channeling in ITER

Alpha particle channeling, the attempt to extract energy from high-energy fusion alpha particles using a combination of high- and low-frequency waves introduced in the plasma with antennae, is studied using a guiding center code. We examine the effect of the combination of cooling caused by a cyclotron mode, particle diffusion due to Alfvén modes introduced for ash removal, the inclusion of microturbulent diffusion, and the slowing down of the alpha particles on electrons. Induced cooling is achieved with a cyclotron resonance, producing additional losses of particles above 3.5 MeV in an amount about equal to the prompt loss. The removal of the low-energy cooled particles by additional modes or by microturbulent diffusion is the hardest challenge for alpha channeling. The cooled alpha particles remain deep in the plasma center, so for this removal, the method used must be capable of providing transport from the plasma center to the edge without also causing losses of high-energy particles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Developing high performance RF heating scenarios on the WEST tokamak

High power experiments, up to 9.2 MW with LHCD and ICRH, have been carried out in the full tungsten tokamak WEST. Here, quasi non inductive discharges have been achieved allowing to extend the plasma duration to 53 s with stationary conditions in particular with respect to tungsten contamination. Transitions to H mode are observed, and H-modes lasting up to 4 s have been obtained. The increase in stored energy is weak since the power crossing the separatrix is close to the L–H threshold. Hot L mode plasmas (central temperature exceeding 3 keV) with a confinement time following the ITER L96 scaling law are routinely obtained. The weak aspect ratio dependence of this scaling law is confirmed. Tungsten accumulation is generally not an operational issue on WEST. Difficulty of burning through tungsten can prevent the discharge from accessing to a hot core plasma in the ramp-up phase, or can lead to rapid collapse of the central temperature when radiation is enhanced by a slight decrease of the temperature. Except a few pulses post-boronization, the plasma radiation is rather high (P rad /P tot ~ 50%) and is dominated by tungsten. This fraction does not vary as the RF power is ramped up and is quite similar in ICRH and/or LHCD heated plasmas. An estimate of the contribution of the RF antennas to the plasma contamination in tungsten is given.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗