Recent advances in oxidative degradation of plastics
Oxidative degradation is a powerful method to degrade plastics into oligomers and small oxidized products.
Chemistry↗
SEARCH · Search NASA
Results for “plastic oxidation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Performance of Vehicle Fuel System Elastomers and Plastics with Test Fuels Representing Gasoline Blended with 10% Ethanol (E10) and 16% Isobutanol (iBu16)
The compatibilities of fuel system elastomers and plastics were evaluated for test fuels containing 16 vol.% isobutanol (iBu16) and 10 vol.% ethanol (E10). Elastomers included two fluorocarbons, four acrylonitrile butadiene rubbers (NBRs), and one type of fluorosilicone, neoprene, and epichlorohydrin/ethylene oxide. Plastic materials included four nylon grades, three polyamides, polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), ethylene tetrafluoroethylene (ETFE), polyphenylene sulfide (PPS), high-density polyethylene (HDPE), polybutylene terephthalate (PBT), polyoxymethylene (POM), flexible polyvinylchloride (PVC), polyetherimide (PEI), polyetheretherketone (PEEK), and a phenol formaldehyde reinforced with glass fiber (GFPF). For each polymer material, the volume, mass, and hardness were measured before and after drying. Dynamic mechanical analysis (DMA) measurements were also performed on the dried specimens.For the elastomer materials the measured properties were similar for both fuels. The fluorocarbons and fluorosilicone swelled the least (~20%), while more moderate (20-45%) expansion occurred for the two NBR hose grades and (ECO). HNBR, neoprene, and silicone exhibited high swelling and softening, which likely precludes their use in many fuel systems. For the plastic materials, the observed swell was low; Nylon 11 swelled around 15%, but otherwise, their measured swell was <10%. Many of the plastics also showed sensitivity to alcohol type, as the E10 test fuel often imparted appreciably higher swell than iBu16. In general, the plastic materials showed good compatibility with the iBu16 and E10 test fuels. Here, the sole exception was the PVC material, which was structurally degraded from exposure to either fuel type. Compositional analysis showed high fuel retention in Nylon 12 and PVC. PVC also experienced a significant reduction in plasticizer compounds following exposure, which resulted in embrittlement and an increase in the glass-to-rubber transition temperature.
33 ADVANCED PROPULSION SYSTEMS↗
Bio‐Inspired Cascade Photocatalysis on Fe Single‐Atom Carbon Nitride Upcycles Plastic Wastes for Effective Acetic Acid Production
Plastic imposes a critical threat to the environment, ecosystems, and human health because of the low utilization efficiency of plastics. Here, we demonstrate a sustainable, highly efficient cascade photocatalysis for upcycle plastics to value-added acetic acid using Fe single-atom catalysts (Fe@C 3 N 4 SAC) at ambient conditions. Inspired by Phanerochaete chrysosporium microbial, the defective Fe@C 3 N 4 SAC acts as a bifunctional cascade photocatalyst for both Fenton-like and CO 2 reduction reactions. During the reaction, hydroxyl radicals (*OH) form and subsequently oxidize plastics into CO 2 intermediates. These CO 2 intermediates are then photo-reduced to CH 3 COOH on the same catalyst via cascade photocatalysis. The mechanism is confirmed by in situ multimodal microscopy and spectroscopies, with density functional theory calculations. A state-of-art CH 3 COOH yield of 63.8 mg h −1 gcat −1 from PVC, 12.7 mg h −1 gcat −1 from PE, 5.4 mg h −1 gcat −1 from PET, and 5.3 mg h −1 gcat −1 from PP are directly obtained under AM1.5G solar irradiation and further validated under real sunlight (≈0.6 sun), achieving 5.6 mg h −1 gcat −1 from PET, using low-cost Fe@C 3 N 4 SAC in a sealed reactor by enhancing the photon transport and utilization efficiency. The techno-economic analysis shows it is promising to practically mitigate plastic based on broader social welfare assessments.
cascade photocatalysis↗
A high throughput assay to detect enzymatic polyethylene oxidation
Biological plastics deconstruction and upcycling have emerged as sustainable alternatives to traditional recycling technologies for plastics waste. The discovery and engineering of efficient thermostable poly(ethylene terephthalate) (PET) hydrolases have made biological PET recycling possible at scale; however, enzymes for non-PET plastics, which account for approximately 70% of all plastics produced, remain largely undiscovered. To accelerate the discovery of such enzymes, we develop a high-throughput screen to detect initial polymer oxidation, specifically that of the C-H bond to an aldehyde. We test 4-hydrazino-7-nitro-2,1,3-benxoxadiozole hydrazine (NBD-H), which reacts with generated aldehydes to form a fluorescent hydrazone on plasma oxidized low-density polyethylene (LDPE) films. Hydrazone generation correlated well with the area of aldehyde peaks as measured by Fourier Transform Infrared Spectroscopy (FTIR) (R2 = 0.92). Moreover, we demonstrate that the probe reliably identifies LDPE-active dye decolorizing peroxidases (DyPs) that generate aldehydes on LDPE films (1.7 – 3.0 fold change relative to background), serving as an effective screen as demonstrated by receiver operating characteristic area under the curve of 0.95. Furthermore, this assay offers an LDPE oxidation screening platform that can be readily parallelized and automated for accelerated discovery of enzymes involved in polyolefin deconstruction.
biocatalysis↗
Catalytic Oxidative Upcycling of Plastic Waste and Heat Integration using Chemical Looping Systems
Explore the source record for details and available documents.
Chung, Elena Y↗
Selective Plasticization of Poly (ethylene oxide) (PEO) Block in Nanostructured Polystyrene– PEO– Polystyrene Triblock Copolymer Electrolytes
The plasticization of a polymer electrolyte usually promotes its ionic conductivity but decreases its storage modulus due to the increased polymer chain flexibility. Herein, we show that such a tradeoff between the ionic conductivity and the mechanical robustness of the polymer electrolyte can be alleviated by selective plasticization of the ion-conductive block, such as poly(ethylene oxide) (PEO) in a polystyrene (PS)– PEO–PS block copolymer (SEO) electrolyte using an ether type plasticizer, tetraethylene glycol dimethyl ether (TEGDME). In this work, at maximum plasticizer loading, the room temperature ionic conductivity increases by up to 3 orders, whereas the storage modulus, G' reduces to half, is still on the order of 10 2 MPa. At above the melting temperature of the PEO block, the dynamic storage modulus, G' of the plasticized membrane surpasses its dry PS-PEO-PS counterpart. Such a phenomenon results from that, a) TEGDME co-crystallizes with PEO to promote its crystallinity and hence the storage modulus, b) TEGDME swells the amorphous PEO phase to enhance the polymer chain segmental mobility and hence ionic conductivity, and c) the PS phase remains intact from TEGDME to keep the SEO elastic.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Mixed Plastics Waste Valorization through Tandem Chemical Oxidation and Biological Funneling
Mixed plastics waste represents an abundant and largely untapped feedstock for the production of valuable products. The chemical diversity and complexity of these materials, however, present major barriers to realizing this opportunity. In this work, we show that metal-catalyzed autoxidation depolymerizes comingled polymers into a mixture of oxygenated small molecules that are advantaged substrates for biological conversion. We engineer a robust soil bacterium, Pseudomonas putida, to funnel these oxygenated compounds into a single exemplary chemical product, either ..beta..-ketoadipate or polyhydroxyalkanoates. This hybrid process establishes a strategy for the selective conversion of mixed plastics waste into useful chemical products.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Electrochemical Oxidation of Lignin and Waste Plastic
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Mapping Rare Earths and Toxics in E-Waste via Hyperspectral Imaging and Machine Learning
Electronic waste (e-waste) presents a mounting challenge to environmental sustainability due to its complex composition, which includes high-value rare earth elements, hazardous organic compounds, and non-recyclable plastics. Accurate and scalable material classification is essential for enabling efficient resource recovery and safe recycling practices. This study introduces a confidence-aware classification pipeline that combines mid-infrared hyperspectral imaging (HSI), spectral angle mapping (SAM), and iterative machine learning to perform pixel-level material identification across e-waste devices. A curated spectral library encompassing artificial materials (e.g., plastic iron oxide, galvanized metals), minerals (e.g., allanite, hematite), and organic compounds (e.g., benzanthracene, toluene) was used to generate pseudo-labels, each assigned a confidence score based on SAM-derived spectral similarity. High-confidence samples from seven consumer electronics—digital cameras, keyboards, laptop fans, modems, motherboards, TV remotes, and speakers—were iteratively expanded and classified using models such as Support Vector Machine (SVM), Random Forest, Gradient Boosting Classifier, Partial Least Squares Discriminant Analysis (PLSDA) and Logistic Regression. The best-performing classifiers achieved macro F1 scores approaching 1.0. Results revealed widespread plastic content (dominated by plastic iron oxide), the presence of rare earth-bearing minerals like cerium-containing allanite, and pervasive detection of hazardous organics such as benzanthracene. Principal Component Analysis (PCA) visualizations and confusion matrices confirmed high separability and robust classification performance. This methodology enables precise, non-destructive, and scalable classification of heterogeneous e-waste streams. It supports automated, hazard-aware sorting in recycling workflows, facilitating selective recovery of critical materials and compliance with circular economy goals. The confidence-aware framework provides a foundation for real-time deployment in industrial settings, offering significant implications for smart e-recycling infrastructure and policy-driven material stewardship.
Circular economy↗
Rapid Accumulation of Soil Inorganics on Plastics: Implications for Plastic Degradation and Contaminant Fate
As plastics degrade in the environment, chemical oxidation of the plastic surface enables inorganics to adsorb and form inorganic coatings, likely through a combination of adsorption of minerals and in situ mineral formation. The presence of inorganic coatings on aged plastics has negative implications for plastics fate, hindering our ability to recycle weathered plastics and increasing the potential for plastics to adsorb contaminants. Here, inorganic coatings formed on terrestrially weathered polyethylene were characterized using synchrotron spectroscopy and microscopy techniques across spatial scales including optical microscopy, nano-X-ray-fluorescence mapping (nano-XRF), nano-X-ray absorption near edge structure (nano-XANES), and high-energy resolution fluorescence detected-XANES (HERFD-XANES). Results indicate a heterogeneous elemental distribution and speciation which includes inorganics common to soil terrestrial environments including iron oxides and oxyhydroxides, aluminosilicates, and carbonates.
36 MATERIALS SCIENCE↗
Highly Stretchable, Ultratough, and Multifunctional Poly(vinyl chloride)-Based Plastics via a Green, Star-Shaped Macromolecular Additive
As one of the most prolifically produced plastics in the world, poly(vinyl chloride) (PVC) suffers from mechanical brittleness and low toughness. Compared with traditional phthalate-type plasticizers, poly(ε-caprolactone) (PCL)-based plasticizers are especially attractive due to their “green” nature and capabilities to achieve improved physical properties. Herein, a stretchable and ultratough PVC-based plastic was achieved by a star-shaped PCL copolymer with a rigid, amino-containing, branched polylactide (N-BPLA) core and a soft PCL shell, that is, RN-SPCLs. With an optimal feed ratio of the CL monomer and N-BPLA core, the RN-SPCL2 can efficiently lower the glass transition temperature (T g ) of PVC plastics, achieving the transition from the “glassy” to “rubbery” state at ambient temperature. The obtained RN-SPCL2/PVC not only shows high extensibility, that is, 453%, but also maintains close to 80% of tensile strength of neat PVC, that is, 30.1 MPa, which is much higher than the previously reported plasticized PVCs. Its overall toughness reaches 92.7 MJ/m 3 , being more than 50-fold higher than neat PVC and 2 to 3 times higher than linear PCL or dibutyl phthalate plasticized PVCs. The important role of star-shaped architecture with a rigid core and flexible PCL shell for RN-SPCL2 in achieving highly stretchable and ultratough PVC plastics is systematically investigated. More interestingly, the as-prepared RN-SPCLs also endow PVC plastics with photoluminescence property and allow homogeneous dispersion of nanosized TiO 2 for significantly enhancing the anti-UV capability.
36 MATERIALS SCIENCE↗
Institute for Catalysis in Energy Processes (ICEP) (Final Report)
The Institute for Catalysis in Energy Processes (ICEP) was a multi-PI program located at the Northwestern University Center for Catalysis and Surface Science from 2006-2024. Over several renewal cycles and several organizing themes, ICEP addressed fundamental questions in catalysis science. In turn, the scientific questions addressed were directly relevant to the efficient use of the nation’s resources to produce fuels and commodity chemicals, harness alternate energy sources for chemical reactions such as light or electricity, reduce emissions and waste, and minimize the impact of our use of plastics. Selective oxidation, (oxidative) dehydrogenation, deNOx, CO 2 reduction, hydrogen release, polymer decomposition / depolymerization, and many other reactions of intense interest to the US Department of Energy were studied in the center. Major ICEP strengths were in catalyst synthesis, in measurements that elucidated catalyst properties, in reaction mechanisms and kinetics, and in predictive theory and modeling. ICEP researchers were often the inventors or developers of materials and methods that were brought to bear on the Institute’s catalytic systems. Key characterization tools advanced through this project included resonance Raman and related techniques, sum frequency generation, and X-ray standing wave spectroscopy. Center members relied extensively on computational tools such as density functional theory and microkinetic modeling to fully investigate catalyst structures and catalytic mechanisms. ICEP researchers were early developers of atomic layer deposition (ALD) for catalyst synthesis and were early pioneers of metal organic frameworks for catalysis. ICEP innovations are found in areas of intense research such as single-atom catalysts, catalytic deconstruction of plastics, and catalytic MOFs, to name a few. Research areas initiated by ICEP indirectly led to DOE EFRCs, startup companies, and other achievements. Over its 18 years of existence, ICEP involved two different PIs (Stair and Notestein) and 24 senior investigators across several academic disciplines at Northwestern University. There were tight collaborations with Argonne National Laboratory, including specialized equipment and experiments permanently located there. The center supported ~400 person-years of effort by graduate students and postdocs, either directly through DOE support or indirectly by leveraging independent support provided to the trainees, e.g. through the NSF GRFP or internal fellowships. The project resulted in 328 manuscripts and numerous conference presentations.
36 MATERIALS SCIENCE↗
Oxidation of n-alkanes using TS-1 and H 2 O 2 : Effects of chain length and solvents
The selective oxidation of n-C 8 H 18 , n-C 12 H 26 , n-C 16 H 34 , n-C 20 H 42 , and n-C 36 H 74 was studied with a goal of using these as models to provide insight into how to functionalize polyolefins. Reactions were carried out using a TS-1 catalyst and H 2 O 2 in a batch reactor with different cosolvents, including methanol, acetone, acetonitrile, methyl ethyl ketone, and methyl butyl ketone. Rates decreased with increasing alkane size, possibly due to the reduced solubility of larger alkanes into the water-rich phases. Cosolvents that promote the partitioning of alkanes in the aqueous phase increased the rates. 1 H NMR spectroscopy demonstrated that ketones were the primary products, although some alcohols also formed. There was preferential reaction at the 2 position in the alkanes, but reaction at central carbons was also observed. The results of this study suggest strategies for using this catalytic chemistry to functionalize polyolefins.
Alkane oxidation↗
Unraveling the Highly Plastic Behavior of ALD-Aluminum Oxide Encapsulations by Small-Scale Tensile Testing
We present a study directly measuring the electron-beam-induced plasticity of amorphous Al 2 O 3 coatings. Core–shell nanostructures are employed as small-scale model systems for two-dimensional coatings made by atomic layer deposition (ALD). Copper nanowires (NWs) are used as substrates for ALD deposition, representing a model system for interconnects commonly found in integrated circuits. Experiments are performed in situ in a transmission electron microscope (TEM) and further analyzed with electron energy loss spectroscopy (EELS). Our in situ TEM tensile experiments reveal the highly plastic behavior of the ALD shell, which withstands a maximum strain of 188%. Comparable samples under beam-off conditions show a brittle fracture, which underlines the effect of electron irradiation. The electron-beam-activated bond switching within the amorphous network enables compensation of the applied tensile strain, leading to viscous flow. By incorporating an intermediate nanocrystalline layer within the Al 2 O 3 shell, the plasticity is suppressed and brittle fracture occurs. This work directly demonstrates the tuning of mechanical properties in amorphous ALD structures through electron irradiation.
36 MATERIALS SCIENCE↗
Insights into Native Single-Atom Electrocatalyst Site Structures
Single-atom electrocatalysts consisting of metal atoms embedded in a carbon matrix are promising next-generation catalysts for green hydrogen production and utilization, CO2 reduction, low-temperature CO oxidation, ammonia production, plastic decomposition, and electrochemical energy storage. The origins of activity and stability for the single-atom sites are still debatable, however, because of constrained insights into their local structure resulting from idealized models and experiments derived from a large number of individual sites. Insights into structural variations around single atomic sites are therefore critical for the continued development of these next-generation catalysts. While electron microscopy commonly provides atomic-scale information about these materials, the beam sensitivity of individual sites makes structural determination by conventional low-voltage (60 keV) techniques challenging. Here, we introduce ultralow-voltage electron ptychography, performed at 30 keV, that enables determination of the lattice structure around individual metal sites in a well-defined single-atom electrocatalyst system while essentially eliminating knock-on structural modifications. Pairing these atomic-scale, site-specific measurements with computational methods will broaden our understanding of the activity and stability of these materials, which will accelerate the development of the next generation of catalysts.
Zachman, Michael [ORNL] (ORCID:0000000319101357)↗
ENDF/B-VIII.1: Thermal Neutron Scattering Sublibrary
The thermal neutron scattering law (TSL) sublibrary aims to describe the interaction of incident neutrons at thermal or sub-thermal energies with different compound materials such fuels, moderators and special-purpose materials. In ENDF/B-VIII.1 there was a large number of new and updated TSL evaluations, including traditional moderators (light water, Beryllium metal, Beryllium Oxide, Calcium Hydride, plastics (Polystyrene and Lucite), graphite (reactor-grade and crystalline), anhydrous Hydrogen Fluoride, and heavy paraffinic oil); exotic moderators (Beryllium Carbide, Zirconium Hydride, Yttrium Hydride, Lithium-7 Hydride and Deuteride), FLiBe molten salt, structural materials and cladding (Silicon Carbide, Silicon Dioxide, Zirconium Carbide), fuels (Plutonium Dioxide, Uranium Carbide, Uranium metal, Uranium Nitride, Uranium Dioxide, Uranium Hydride), and special purpose materials. In ENDF/B-VIII.1 we also distribute alongside the evaluated files, a comma-separated file (CSV), named TSL_MAT_numbers.csv, which lists all evaluated files in the current release and their corresponding unique MAT number.
73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
Changes in SSL Device Efficiency and Optical Performance Under Accelerated Aging Conditions
Lighting application efficiency (LAE) describes the efficient delivery of light from the light source to the lighted task and is viewed as a new frontier—increasing energy savings with solid-state lighting (SSL) technologies. The framework for LAE that is proposed by the U.S. Department of Energy (DOE) consists of four major elements: light source efficiency, optical delivery efficiency, spectral efficiency, and intensity effectiveness. This report focuses on a sampling of the available SSL products that can be broadly defined as having modified spectral output because the method of spectra modification has a significant impact on light source efficiency and long-term optical delivery and spectral efficiencies. This report focused on the changes in light source, optical delivery, and spectral efficiencies that occur during aging of SSL devices. An accelerated stress test (AST) regiment was developed for the devices under test (DUTs) examined in this report to provide insights into how the performance of SSL devices change with aging. The AST protocols demonstrate that the SSL products discussed in this report often reduce light source efficiency to achieve different spectral characteristics. In addition, aging of the optical components (e.g., lenses, solder masks) in SSL devices can produce increased light absorption, which negatively impacts optical delivery efficiency and light source efficiency. The modified spectral outputs of the selected SSL products discussed in this report come in a variety of form factors and achieve enhanced optical performance by using a variety of methods. All of the products examined in this study use mid-power light-emitting diodes (MP-LEDs), although the number, configuration, phosphor content, and light-emitting diode (LED) pump of the MP-LEDs differ. Product MS-1 is a 60-watt (W) replacement A19 lamp with a hermetically sealed glass globe, which contains an embedded optical filter to absorb green and yellow emissions, thereby creating a “sunlike” modified spectrum. Product MS-2 is a 60-W replacement A19 lamp with 30 MP-LEDs, and it uses a violet LED pump, along with green and red phosphor emissions, to produce a “healthy” spectrum. This spectrum omits blue emissions in an effort to reduce melanopic lux. Product MS-3 is an LED module consisting of 21 MP-LEDs that use a violet LED pump, along with blue, green, and red phosphors, to produce a “sunlike” spectrum. Products MS-4 and MS-5 are both 6-inch (in) downlights that use a manual switching mechanism so that users can select application-specific correlated color temperatures before installation. Products MS-4 and MS-5 both contain two LED primaries (2,700 Kelvin [K] and 5,000 K) for spectral tuning. Product MS-4 contains 12 MP-LEDs for each LED primary, and Product MS-5 contains 10 MP-LEDs for each LED primary. This report summarizes the overall findings from up to 8,000 hours (hrs) of AST on the lamp DUTs (Products MS-1 and MS-2); up to 5,000 hrs of AST on the LED light engine DUTs (Product MS-3); and up to 7,000 hrs of AST on the downlight DUTs (Products MS-4 and MS-5). The AST procedures used in this study included a room temperature operational life (RTOL) test, an operational life test conducted at 45 degrees Celsius (°C; 45OL) test, an operational life test conducted at 75°C (75OL), a wet high-temperature operational life test performed at 65°C and 90% relative humidity (6590), and a wet high-temperature operational life test performed at 75°C and 75% relative humidity (7575). The AST procedures used for Products MS-1 and MS-2 were RTOL, 45OL, and 6590. The AST procedures used for Products MS-3, MS-4, and MS-5 were RTOL, 75OL, and 7575. During the ASTs described herein, separate populations of each product (three DUTs in each population for Products MS-1, MS-2, MS-4, and MS-5; four DUTs in each population for Product MS-3) were subjected to power cycling of 1 hr on and 1 hr off. The key findings from this study include the following. Enhanced optical performance came at the cost of reduced light source efficiency for the lamps and light engines examined in this study. The optical filter used to produce a “sunlike” spectrum for Product MS-1 reduced light source efficiency by 26%, from 113 lumens per watt (lm/W) to 85 lm/W. Products MS-2 and MS-3 that used a violet-pumped LED to achieve “healthy” and “sunlike” enhanced optical performance, respectively, suffered the largest reduction in initial light source efficiency (49 lm/W for Product MS-2 and 68 lm/W for Products MS-3) perhaps because of the use of violet LED as the optical pump. Product MS-2 also had the poorest color fidelity because of undersaturation of blues and oversaturation of greens and yellows. Chromaticity maintenance of the products in this study was generally good, with parametric failure only occurring for one product at one AST condition (i.e., Product MS-3 at 7575). The chromaticity shift for Product MS-3 in 7575 test conditions resulted from reduced emissions of the broad green and red phosphors used to mimic sunlight in the 500–750 nanometer (nm) range. As a result of these phosphor emission losses, chromaticity shifted toward the more stable violet-pumped LED and blue phosphor. Although chromaticity maintenance was acceptable for most products tested, different chromaticity shift mechanisms were observed for temperature and humidity tests compared with temperature alone for Products MS-1, MS-2, and MS-3. For Product MS-1, a relative increase in green emissions was observed with humidity, which may indicate humidity-accelerated degradation of the optical filter at green wavelengths (optical delivery efficiency reduction) or degradation of the emitters in the red region (spectral efficiency reduction). The violet-pumped products (i.e., MS-2 and MS-3) exhibited different chromaticity shift behavior in the temperature-humidity environments, with Product MS-2 shifting generally yellow because of photo-induced oxidation of the plastic globe (i.e., a reduction of optical delivery efficiency) and Product MS-3 shifting toward violet and blue emitters because of faster loss of emission from green and red phosphors (i.e., a reduction in spectral efficiency). Because of an initial drop in power consumption, the light source efficiency of downlights (Products MS-4 and MS-5) increased at RTOL throughout the test duration. The light source efficiency initially increased during 75OL until a decay in luminous flux maintenance (LFM) dominated light source efficiency, whereas the light source efficiency decreased for the entire 7575 test duration. It was found that increasing the ambient environment of an SSL device from 25°C to 75°C decreases the LFM by 2.7 to 5.5, depending on design of the SSL device. Adding humidity to the system (75OL to 7575) was found to decrease LFM by another factor of approximately 3.0. A common location of failure was identified for the downlights (Products MS-4 and MS-5) operated in the 7575 environment. This failure abruptly occurred between 3,000 to 5,000 hrs of testing on the film capacitor of the electromagnetic interference (EMI) filter near the diode bridge for 11 of the 12 downlights. It is likely that this failure was caused by a combination of the high electrical voltage across the capacitor, the location of the capacitor near the heat sources (e.g., transformers, diode bridges, power resistors), and the high stress environment of 7575. Longer test times are needed to fully understand the LFM, luminous efficacy changes, and chromaticity shifts for some of the products. Because of the high reliability, light source efficiency, and spectral tuning capabilities of LEDs, the expectations of LAE for SSL products are greatly increased over traditional lighting products. The data gathered in this report begin to provide an understanding of the tradeoffs that current SSL products undergo when optimizing the different efficiency elements of LAE. As discussed in this report, the findings from the tests conducted show that the optimization of spectral efficiency can come at the cost of initial light source efficiency. Furthermore, the introduction of violet LEDs can promote long-term optical delivery efficiency degradation, and the introduction of optical filters or new phosphors can lead to unwanted spectral efficiency changes because the ratio of phosphor emitters changes with aging. The data presented in this report also identified a common failure location in 6-in downlights. The results regarding long-term behavior of the modified spectra devices studied provide valuable information about changes to the light source, spectral, and optical delivery efficiencies as the devices age. This information can be used to improve future SSL designs.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗