Search NASA⌕ Search

SEARCH · Search NASA

Results for “plastic tuning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Tuning of Multicell Superconducting Accelerating Cavities Using Pressurized Balloons

Plastic tuning of multicell superconducting accelerating cavities is crucial in the development cycle of cavities for particle accelerators. Cavities must meet stringent requirements regarding the operating mode frequency, field flatness, and eccentricity before lining them up in a cryomodule string. After dressing bare cavities with helium vessels, the welded vessel prevents access to individual cavity cells disallowing any further localized tuning. Currently, there is no straightforward way to tune dressed cavities other than cutting the vessel and then tuning the bare cavity and dressing it back, which would significantly impact cost and schedule. In this work, we present a novel tuning technique for already jacketed cavities that is non-invasive and cost-effective. The proposed scheme employs pressurized balloons to be temporarily deployed inside the cavity as a means to localize mechanical deformation in specific cells. The proposed tuning technique was successfully utilized to recover a 9-cell 1.3 GHz tesla-style cavity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

First characterisation of the MAGO cavity, a superconducting RF detector for kHz–MHz gravitational waves

Heterodyne detection using microwave cavities is a promising method for detecting high-frequency gravitational waves (GWs) or ultralight axion dark matter. In this work, we report on studies conducted on a spherical 2-cell cavity developed by the MAGO collaboration for high-frequency GWs detection. Although fabricated around 20 years ago, the cavity had not been used since. Due to deviations from the nominal geometry, we conducted a mechanical survey and performed room-temperature plastic tuning. Measurements and simulations of the mechanical resonances and electromagnetic properties were carried out, as these are critical for estimating the cavity’s GW coupling potential. Based on these results, we plan further studies in a cryogenic environment. The cavity characterisation does not only provide valuable experience for a planned physics run but also informs the future development of improved cavity designs.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Tailoring planar slip to achieve pure metal-like ductility in body-centred-cubic multi-principal element alloys

Uniform tensile ductility (UTD) is crucial for the forming/machining capabilities of structural materials. Normally, planar-slip induced narrow deformation bands localize the plastic strains and hence hamper UTD, particularly in body-centred-cubic (bcc) multi-principal element high-entropy alloys (HEAs), which generally exhibit early necking (UTD < 5%). Here we demonstrate a strategy to tailor the planar-slip bands in a Ti-Zr-V-Nb-Al bcc HEA, achieving a 25% UTD together with nearly 50% elongation-to-failure (approaching a ductile elemental metal), while offering gigapascal yield strength. The HEA composition is designed not only to enhance the B2-like local chemical order (LCO), seeding sites to disperse planar slip, but also to generate excess lattice distortion upon deformation-induced LCO destruction, which promotes elastic strains and dislocation debris to cause dynamic hardening. Further, this encourages second-generation planar-slip bands to branch out from first-generation bands, effectively spreading the plastic flow to permeate the sample volume. Moreover, the profuse bands frequently intersect to sustain adequate work-hardening rate (WHR) to large strains. Our strategy showcases the tuning of plastic flow dynamics that turns an otherwise-undesirable deformation mode to our advantage, enabling an unusual synergy of yield strength and UTD for bcc HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of Antimicrobial PLA Composites for Fused Filament Fabrication

In addition to possessing the desirable properties of being a biodegradable and biocompatible polymer fabricated from renewable resources, poly (lactic acid) (PLA) has useful mechanical and thermal attributes that has enabled it to be one of the most widely-used plastics for medicine, manufacturing, and agriculture. Yet, PLA composites have not been heavily explored for use in 3D-printing applications, and the range of feasible materials for the technology is limited, which inhibits its potential growth and industry adoption. In this study, tunable, multifunctional antimicrobial PLA composite filaments for 3D-printing have been fabricated and tested via chemical, thermal, mechanical, and antimicrobial experiments. Thermally stable antimicrobial ceramics, ZnO and TiO2, were used as fillers up to 30 wt%, and poly (ethylene glycol) (PEG) was used as a plasticizer to tune the physical material properties. Results demonstrate that the PLA composite filaments exhibit the thermal phase behaviors and thermal stability suitable for 3D-printing. Additionally, PEG can be used to tune the mechanical properties while not affecting the antimicrobial efficacy that ZnO and TiO2 imbue.

TiO2↗
DOE OSTI2023

Thiol–ene Click Chemistry Incorporates Hydroxyl Functionality on Polycyclooctene to Tune Properties

Polyolefins compose the majority of plastic waste, but conventional mechanical recycling degrades their properties, thereby reducing their value. We report the functionalization of a model for dehydrogenated polyethylene, polycyclooctene (PCOE), with thiol–ene click chemistry to install pendant hydroxyl ethyl thioethers. Functionalization of PCOE using mercaptoethanol via thiol–ene click chemistry yielded functionalization between 1.4 and 22.9% based on ethylene monomeric units. Reactions were well-controlled by varying the reagent stoichiometry and reaction time. Crystallinity and melting temperature decreased, and glass transition temperature increased with greater functionalization. Contact angle measurements reveal an increase in surface polarity with functionalization. Here, comparisons with poly(ethylene-co-vinyl alcohol) (EVOH) show comparable surface polarity at similar levels of alcohol functionalization. At 12% functionalization, the ultimate shear stress (USS) of functionalized PCOE in an adhesive configuration is 4.10 ± 0.48 MPa, comparable to EVOH. At >12% functionalization, the failure mode changed from adhesive to mixed adhesive–cohesive, and the USS decreased.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding and tuning organocatalysts for versatile condensation polymer deconstruction

Plastics are widely used for their durability and versatility, but recycling remains a major challenge, especially for mixed or contaminated waste. Mechanical recycling works well for clean, single-polymer streams like PET but has limited efficiency for complex waste streams. Chemical recycling, particularly glycolysis, is often employed to selectively deconstruct condensation polymers under mild conditions. This study explores catalyst design for glycolysis using linear free energy (Hammett) analysis to evaluate how catalyst structure influences polymer deconstruction. Polycaprolactone (PCL) is used as a model polyester due to its solubility and low deconstruction temperature. Triazabicyclodecene (TBD) paired with benzoic acid derivatives depicts a clear linear trend in depolymerization rates with Hammett values. TBD with p-aminobenzoic acid (PABA) stands out for its catalytic efficiency, thermal stability, and scalability, along with PABA's commercial availability as vitamin B-10. The TBD : PABA catalyst not only effectively breaks down PCL but also enables sequential deconstruction of polycarbonate, PET, and Nylon in mixed waste streams. These results highlight the value of Hammett-guided catalyst design and establish TBD : PABA as a promising, scalable organocatalyst for mixed plastic recycling, enabling recovery of individual polymer building blocks from blended waste and offering a practical route toward circular plastics.

Zheng, Jackie [Univ. of Tennessee, Knoxville, TN (↗
DOE OSTI2021

Polyolefin plastic waste hydroconversion to fuels, lubricants, and waxes: a comparative study

Hydroconversion technologies have surged to the forefront of deconstructing plastic waste. Recent studies have been performed over several catalysts with varying conditions and plastics that make comparisons difficult. We compile and compare data from the literature by introducing various metrics and perform a simple energy analysis. We draw mechanistic similarities to and differences from the past literature on small alkane hydroconversion and leverage the former to propose standard approaches to tune product selectivity. We exemplify the plastics materials gap and the challenges it creates. Lastly, we discuss the current limitations and suggest future work.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Fundamental Structure/Property Studies of Gas Separation Membrane Polymers

Solution-processable polybenzimidazoles (PBIs) present opportunities for new gas separation membranes. We plan to develop systematic structure/property relations for this relatively new class of membrane materials. The fundamental questions we will address are: (1) How do chemical structure modifications of PBIs influence their gas solubility, diffusivity and permeability properties for a systematic series of gases? (2) Is the separation performance of PBIs affected by plasticization under operating conditions that are relevant to, for example, natural gas purification or olefin/paraffin separation and, if so, can this family of materials be tuned structurally to minimize deleterious effects of plasticization on separation properties? (3) What is the effect of water vapor on PBI separation performance? (4) What is the influence of physical aging on permeation properties of thin (i.e., <1 µm) PBI polymer films, and how does the rate of physical aging relate to polymer chemical structure? The primary focus of this research program is to develop a fundamental, molecular-based mechanistic understanding of the influence of chemical structure on the gas transport properties of PBIs and to establish structure/property relationships for this unique platform of materials.

08 HYDROGEN↗
DOE OSTI2021

Enhanced superconductivity and ferroelectric quantum criticality in plastically deformed strontium titanate

The properties of quantum materials are commonly tuned using experimental variables such as pressure, magnetic field and doping. Here we explore a different approach using irreversible, plastic deformation of single crystals. We show that compressive plastic deformation induces low-dimensional superconductivity well above the superconducting transition temperature (Tc) of undeformed SrTiO3, with evidence of possible superconducting correlations at temperatures two orders of magnitude above the bulk Tc. The enhanced superconductivity is correlated with the appearance of self-organized dislocation structures, as revealed by diffuse neutron and X-ray scattering. We also observe deformation-induced signatures of quantum-critical ferroelectric fluctuations and inhomogeneous ferroelectric order using Raman scattering. Our results suggest that strain surrounding the self-organized dislocation structures induces local ferroelectricity and quantum-critical dynamics that strongly influence Tc, consistent with a theory of superconductivity enhanced by soft polar fluctuations. Our results demonstrate the potential of plastic deformation and dislocation engineering for the manipulation of electronic properties of quantum materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Understanding the effect of refractory metal chemistry on the stacking fault energy and mechanical property of Cantor-based multi-principal element alloys

Multi-principal-element alloys (MPEAs) based on 3d-transition metals show remarkable mechanical properties. In this study, the stacking fault energy (SFE) in face-centered cubic (fcc) alloys is a critical property that controls underlying deformation mechanisms and mechanical response. Here, we present an exhaustive density-functional theory study on refractory- and copper-reinforced Cantor-based systems to ascertain the effects of refractory metal chemistry on SFE. We find that even a small percent change in refractory metal composition significantly changes SFEs, which correlates favorably with features like electronegativity variance, size effect, and heat of fusion. For fcc MPEAs, we also detail the changes in mechanical properties, such as bulk, Young's, and shear moduli, as well as yield strength. A Labusch-type solute-solution-strengthening model was used to evaluate the temperature-dependent yield strength, which, combined with SFE, provides a design guide for high-performance alloys. We also analyzed the electronic structures of two down-selected alloys to reveal the underlying origin of optimal SFE and strength range in refractory-reinforced fcc MPEAs. These new insights on tuning SFEs and modifying composition-structure-property correlation in refractory- and copper-reinforced MPEAs by chemical disorder, provide a chemical route to tune twinning- and transformation-induced plasticity behavior in fcc MPEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Vortex phases and glassy dynamics in the highly anisotropic superconductor HgBa 2 CuO 4+δ

We present an extensive study of vortex dynamics in a high-quality single crystal of HgBa 2 CuO 4+ δ , a highly anisotropic superconductor that is a model system for studying the effects of anisotropy. From magnetization M measurements over a wide range of temperatures T and fields H , we construct a detailed vortex phase diagram. We find that the temperature-dependent vortex penetration field H p ( T ), second magnetization peak H smp ( T ), and irreversibility field H irr ( T ) all decay exponentially at low temperatures and exhibit an abrupt change in behavior at high temperatures T / T c >~0.5. By measuring the rates of thermally activated vortex motion (creep) S ( T , H ) = | d ln M ( T , H )/ d ln t |, we reveal glassy behavior involving collective creep of bundles of 2D pancake vortices as well as temperature- and time-tuned crossovers from elastic (collective) dynamics to plastic flow. Based on the creep results, we show that the second magnetization peak coincides with the elastic-to-plastic crossover at low T , yet the mechanism changes at higher temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Amorphous complexions alter the tensile failure of nanocrystalline Cu-Zr alloys

Grain boundary-based mechanisms are known to control the plastic deformation and failure of nanocrystalline metals, with manipulation of the boundary structure a promising path for tuning this response. In this study, the role of interfacial structural disorder on plasticity and failure of nanocrystalline Cu-Zr alloys is investigated with in situ scanning electron microscopy tensile deformation experiments. Two model materials are created, one with only the typical ordered grain boundaries and another with amorphous intergranular films interspersed into the boundary network, while the microstructures are otherwise identical. Hence, the importance of complexion type on plasticity and failure is isolated by only varying complexion structure. Here, the tensile experiments show that failure of the samples containing amorphous films is significantly retarded, as evidenced by an increase in the cross-sectional area reduction, a decrease in the occurrence of shear-dominated failure, a decrease in strain localization, and fracture surfaces with more elongated dimple features. As a whole, this study provides direct evidence that structural disorder at the grain boundaries can be beneficial for improving the ductility of nanocrystalline metals.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Scalable, biologically sourced depolymerizable polydienes with intrinsically weakened carbon–carbon bonds

Currently, there are few examples of circularly recyclable polymers with all-carbon backbones, probably owing to the challenge of using selective C–C bond cleavage to efficiently produce monomers in recycling processes. Furthermore, here we demonstrate a series of biologically sourced polymuconate polymers synthesized via simple free-radical polymerization that exhibit intrinsically weakened C–C bonds and controlled chemical recycling to monomers. Modifying the side chains and copolymerization ratios allows a wide range of mechanical property tuning, achieving performances comparable to those of commercial plastics such as polystyrene, polymethyl methacrylate and polybutadiene. Techno-economic analysis and life cycle assessment for production at a scale of 100 kilotons per year show that the materials are currently slightly more expensive and environmentally intensive compared with conventional rubbers. However, use of recycled materials via depolymerization can greatly decrease the cost and environmental impacts of polymuconate production (for example, down to US$1.59 per kilogram) to outperform its commercial counterparts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

CO 2 Mineralization Using Porous Carbon and Industrial Wastes to Make Multifunctional Concrete

Along with substantial benefits and promises of carbon capture and storage (CCS) technologies, significant challenges exist in developing scalable materials and methods for capture and of CO 2 . The overarching objective of this project is to provide a system approach for developing a new CO 2 capture and utilization technology using porous carbon and industrial wastes to make a low-cost, scalable and multifunctional concrete product. The objective of Phase I of this project is to develop and fine-tune activated carbons from different wastes such as plastic wastes to offer a cheap, abundant and scalable feedstock for CO 2 uptake. The objective of Phase 2 is creating a facile protocol to develop a concrete prototype comprising CO 2 adsorbed activated carbon (e.g. from plastic wastes), followed by product validation, life-cycle analysis, and bench-scale testing. The project objectives are designed to specifically obtain a final product and technology that directly addresses the main goals of the DOE’s CCS programs.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Catalytic Consequences of Hierarchical Pore Architectures within MFI and FAU Zeolites for Polyethylene Conversion

The benefits of hierarchical zeolites for the conversion of bulky molecules like polymeric waste have been reported in the literature; however, the impact of mesopore sizes and connectivities on rates, product selectivities, and catalyst deactivation in the context of plastic upcycling has not been systematically probed. Here, in this study, we synthesized a suite of hierarchical MFI and FAU zeolites via desilication under varying conditions for metal-free polyethylene conversion reactions under batch and flow conditions (473–523 K). Polyethylene (solid) conversion rates (normalized by Bro̷nsted acid site density) were higher on hierarchical than parent microporous MFI regardless of mesopore connectivities, i.e., open or constricted, suggesting that the incorporation of mesopores facilitates diffusion of intermediate products to access medium-pore protons for successive scission events. Furthermore, higher branched:linear gaseous product ratios were produced on hierarchical than parent MFI, since mesopores allow for egress of bulkier molecules without undergoing further secondary events, e.g., isomerization back to linear alkanes/alkenes or beta scission. Solid conversion rates on hierarchical FAU synthesized via desilication with cetyltrimethylammonium bromide (CTABr), however, were not higher than parent FAU, likely because the presence of CTABr facilitates recrystallization of leached species to form composites (hierarchical FAU and ordered mesoporous materials) with more isolated mesopores. The stagnation in rates, despite increased mesopore volumes (>0.22 cm 3 g –1 ), highlights the importance of confinement effects provided by micropores for cleaving C–C bonds at modest reaction conditions. In situ 1 H MAS NMR performed on polyethylene with MFI zeolite show that PE isomerizes (and potentially deconstructs) at temperatures near 450 K, highlighting the role of Bro̷nsted acid sites in activating C–C bonds under mild reaction conditions. Catalyst recyclability studies showed that all catalysts undergo deactivation during plastic upcycling reactions, but to varying extents. Overall, hierarchical materials have better catalyst stability than parent materials, although the differences in stability between hierarchical and parent FAU are smaller than those for MFI. Taken together, these findings demonstrate how rates, selectivities, and catalyst deactivation from plastic upcycling reactions can be controlled via fine-tuning the identity and connectivity of mesopores.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Strong and recyclable bio-derived poly(ester amide) hot-melt adhesive

Bio-based adhesives offer inherent advantages over conventional petrochemical-derived systems, including renewable sourcing, reduced environmental impact and potential degradability. However, most bio-based adhesives suffer from poor adhesion strength, limited substrate compatibility and a lack of chemical recyclability. Here, in this work, we present a bio-derived multiblock poly(ester amide) adhesive that leverages microphase segregation between different segments to reconcile mechanical robustness with strong interfacial bonding. Notably, this multiblock architecture is accessed through a one-pot, selective acceptorless dehydrogenative polymerization, obviating the need for multistep synthesis. The materials exhibit excellent adhesion across a range of substrates including metals, glass and wet wood surpassing commercial benchmarks, while also demonstrating thermal stability, tunable mechanical properties and closed-loop chemical recyclability even in the presence of other commodity plastics. Furthermore, the adhesive strength of these materials could be tuned for various potential applications through control over the chemical composition of the polymer. By integrating renewable feedstocks, high-performance functionality and efficient chemical circularity within a single platform, this work provides a viable pathway toward more sustainable adhesive technologies and contributes to advancing circular materials manufacturing.

09 BIOMASS FUELS↗
DOE OSTI2021

Minimizing Oxygen Permeability in Chitin/Cellulose Nanomaterial Coatings by Tuning Chitin Deacetylation

The demand for packaging materials with low gas permeabilities is increasing, but commonly used petroleum-derived single-use plastics are not renewable, biodegradable, or easy to recycle. Nanomaterials composed of chitin and cellulose, which are abundant in nature, have high crystallinities and low oxygen permeabilities (OP), providing a viable alternative. In this work, we explore how deacetylation conditions of crab shell chitin can be used to tune the charge and size of resulting chitin nanowhiskers (ChNWs) and the resulting OP of layered film structures. Three deacetylation factors, the concentration of sodium hydroxide (%NaOH), temperature (T), and reaction time, were explored using a three-factor three-level Taguchi design with an orthogonal array. Furthermore, the resulting ChNW suspensions were sequentially spray-coated with suspensions of cellulose nanocrystals (CNCs) onto cellulose acetate (CA) films to form a multilayer structure. We show that ChNWs prepared under more aggressive deacetylation conditions inside the original orthogonal array (higher %NaOH, T, and time) had shorter lengths but the surface charge was significantly influenced only by more aggressive deacetylation outside of the original design conditions. With only ~10% decrease in the ultimate tensile strength and no significant loss in failure strain, the ChNW-CNC coating resulted in ~20% decrease in WVTR in comparison to uncoated CA films. The optimization of process conditions resulted in CA-ChNW-CNC films with a 91-99% decrease in OP (132-16.7 cm 3 ∙μm/m 2 /day/kPa versus 1553 cm3∙μm/m2/day/kPa for uncoated CA).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Chain-length-controllable upcycling of polyolefins to sulfate detergents

Escalating global plastic pollution and the depletion of fossil-based resources underscore the urgent need for innovative end-of-life plastic management strategies in the context of a circular economy. Thermolysis is capable of upcycling end-of-life plastics to intermediate molecules suitable for downstream conversion to eventually high-value chemicals, but tuning the molar mass distribution of the products is challenging. Here, in this study, we report a temperature-gradient thermolysis strategy for the conversion of polyethylene and polypropylene into hydrocarbons with tunable molar mass distributions. The whole thermolysis process is catalyst- and hydrogen-free. The thermolysis of polyethylene and polyethylene/polypropylene mixtures with tailored temperature gradients generated oil with an average chain length of ~C 14 . The oil featured a high concentration of synthetically useful α-olefins. Computational fluid dynamics simulations revealed that regulating the reactor wall temperature was the key to tuning the hydrocarbon distributions. Subsequent oxidation of the obtained α-olefins by sulfuric acid and neutralization by potassium hydroxide afforded sulfate detergents with excellent foaming behaviour and emulsifying capacity and low critical micelle concentration. Overall, this work provides a viable approach to producing value-added chemicals from end-of-life plastics, improving the circularity of the anthropogenic carbon cycle.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗