SEARCH · Search NASA

Results for “polybenzimidazole (PBI)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Flue Gas Desulfurization (FGD) Wastewater Treatment Using Polybenzimidazole (PBI) Hollow Fiber (HF) Membranes

Polybenzimidazole (PBI) hollow fiber membranes were used to treat flue gas desulfurization (FGD) wastewater (WW) from a coal fired power plant. Membranes were tested using both single salt solutions and real FGD WW. The PBI membranes showed >99% rejection for single salt solutions of NaCl, MgCl2, CaSO4, and CaCl2 at approximately 2000 PPM (parts per million). The membranes also showed >97% rejection for FGD WW concentrations ranging from 6900 to 14,400 PPM total dissolved solids (TDS). The pH of the FGD WW was adjusted between 3.97–8.20, and there was an optimal pH between 5.31 and 7.80 where %rejection reached a maximum of >99%. The membranes were able to operate stably up to 50 °C, nearly doubling the water flux as compared to room temperature, and while maintaining >98% salt rejection.

activation energy↗

DOE OSTI2025

Fabrication and Scale-Up of Porous Polybenzimidazole (PBI) Supports for Gas Separation Composite Membranes

Industrial gas separation often uses thin film composite (TFC) membranes comprising a porous support overlaid with a single-/multi-layer gas-selective thin film. An optimal porous support should possess high surface porosity to minimize gas transport resistance and nano-sized pores to ease pore penetration occurring during the thin film coating process. Good chemical and thermal stabilities are essential to withstand the aggressive solvents and heat required for the thin film coating and curing. However, few porous membranes satisfy all these requirements. This study presents a scalable membrane formation method of making highly porous polybenzimidazole (PBI) supports via non-solvent induced phase separation. This presentation also details the scale-up fabrication of PBI supports using a custom roll-to-roll membrane casting machine.

gas separation↗

DOE OSTI2020

Prediction of Performance Variation Caused by Manufacturing Tolerances and Defects in Gas Diffusion Electrodes of Phosphoric Acid (PA)–Doped Polybenzimidazole (PBI)-Based High-Temperature Proton Exchange Membrane Fuel Cells

The automated process of coating catalyst layers on gas diffusion electrodes (GDEs) for high-temperature proton exchange membrane fuel cells results inherently into a number of defects. These defects consist of agglomerates in which the platinum sites cannot be accessed by phosphoric acid and which are the consequence of an inconsistent coating, uncoated regions, scratches, knots, blemishes, folds, or attached fine particles—all ranging from μm to mm size. These electrochemically inactive spots cause a reduction of the effective catalyst area per unit volume (cm2/cm3) and determine a drop in fuel cell performance. A computational fluid dynamics (CFD) model is presented that predicts performance variation caused by manufacturing tolerances and defects of the GDE and which enables the creation of a six-sigma product specification for Advent phosphoric acid (PA)-doped polybenzimidazole (PBI)-based membrane electrode assemblies (MEAs). The model was used to predict the total volume of defects that would cause a 10% drop in performance. It was found that a 10% performance drop at the nominal operating regime would be caused by uniformly distributed defects totaling 39% of the catalyst layer volume (~0.5 defects/μm2). The study provides an upper bound for the estimation of the impact of the defect location on performance drop. It was found that the impact on the local current density is higher when the defect is located closer to the interface with the membrane. The local current density decays less than 2% in the presence of an isolated defect, regardless of its location along the active area of the catalyst layer.

Gurau, Vladimir (ORCID:0000000327429061)↗

DOE OSTI2022

Polybenzimidazole (PBI) membranes for redox flow batteries

Disclosed are redox flow battery membranes, redox flow batteries incorporating the membranes, and methods of forming the membranes. The membranes include a polybenzimidazole gel membrane that is capable of incorporating a high liquid content without loss of structure that is formed according to a process that includes in situ hydrolysis of a polyphosphoric acid solvent. The membranes are imbibed with a redox flow battery supporting electrolyte such as sulfuric acid and can operate at very high ionic conductivities of about 100 mS/cm or greater. Redox flow batteries incorporating the PBI-based membranes can operate at high current densities of about 100 mA/cm2 or greater.

Benicewicz, Brian C.↗

DOE OSTI2023

Polybenzimidazole (PBI) membranes for redox flow batteries

Benicewicz, Brian C.↗

DOE OSTI2022

Low permeability polybenzimidazole (PBI) gel membranes for redox flow batteries

Disclosed are redox flow battery membranes, redox flow batteries incorporating the membranes, and methods of forming the membranes. The membranes include a densified polybenzimidazole gel membrane that is capable of incorporating a high liquid content without loss of structure that is formed according to a process that includes in situ hydrolysis of a polyphosphoric acid solvent followed by densification of the gel membrane. The densified membranes are then imbibed with a redox flow battery supporting electrolyte such as sulfuric acid and can operate at very high ionic conductivities of about 50 mS/cm or greater and with low permeability of redox couple ions, e.g. vanadium ions, of about 10−7 cm2/s or less. Redox flow batteries incorporating the membranes can operate at current densities of about 50 mA/cm2 or greater.

Benicewicz, Brian C.↗

DOE OSTI2023

NMR investigation of proton transport in polybenzimidazole/polyphosphoric acid membranes prepared via novel synthesis route

Here, in this work, we present a molecular-level view of the structural changes in polybenzimidazole (PBI) membranes doped with phosphoric acid (PA) generated by a novel membrane fabrication technique. The modified PA doped membranes displayed unprecedented ionic conductivity at elevated temperatures, comparable to the starting PBI gel membranes prepared by the commonly used PPA process, while also exhibiting enhanced mechanical properties. To elucidate the cause of these effects, we used multi-nuclear ( 1 H, 13 C, 31 P) 1D PFG, MAS and CPMAS, and 2D HETCOR magnetic resonance (NMR) techniques to characterize the structure and dynamics of the modified film and the original gel PBI membranes. 1 H diffusivity measurements show significantly enhanced proton diffusivity, both in magnitude and in lower activation energy, which were consistent with its high ionic conductivity despite the lower PA content compared to the original gel membrane. CPMAS experiments further substantiated that the location of these distinct phosphate environments as being close to the polymer network. Finally, the phosphate groups in the modified membrane were revealed to be strongly bounded to each other and to the PBI polymer backbone in contrast to the combination of weakly and strongly bounded groups of the original gel membrane.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2020

A comparative experimental study of the hygroscopic and mechanical behaviors of electrospun nanofiber membranes and solution–cast films of polybenzimidazole

This article reports a comparative experimental study of the hygroscopic and mechanical behaviors of electrospun polybenzimidazole (PBI) nanofiber membranes and solution-cast PBI films. As-electrospun nonwoven PBI nanofiber mats (with the nanofiber diameter of ~250 nm) were heat-pressed under controlled temperature, pressure and duration for the study; lab-made solution-cast PBI films and commercially available PBI films (the PBI Performance Product Inc., Charlotte, NC) were used as the control samples. Thermogravimetric and microtensile tests were utilized to characterize the hygroscopic (moisture absorption) and mechanical properties of the PBI nanofiber membranes at varying heat-pressing conditions, which were further compared to those of solution-cast PBI films. Experimental results indicated that the PBI nanofiber membranes carried slightly higher thermal stability and less hygroscopic properties than those of solution-cast PBI films. In addition, heat-pressing conditions significantly influenced the mechanical properties of the resulting PBI nanofiber membranes. The stiffness and tensile strength increase with increasing either the heat-pressing pressure or duration, and relevant mechanisms were explored. Here, the present study provides a rational understanding of the hygroscopic and mechanical behaviors of electrospun PBI nanofiber membranes and solution-cast PBI films that are beneficial to their reliable cutting-edge applications in high-temperature filtration, polymer electrolyte membranes (PEMs), etc.

25 ENERGY STORAGE↗

DOE OSTI2022

Intermediate-Temperature Proton Exchange Membranes Based on Cerium Ultraphosphate Composited with Polybenzimidazole

This paper reports the rational fabrication and structural, thermal, mechanical and electrochemical characterization of a new type of intermediate-temperature (IT) polymer-inorganic composite (PIC) proton exchange membranes (PEMs) that are made of cerium ultraphosphate (CeP 5 O 14 —CUP) as the solid-state proton conductor composited with a high-temperature (HT) polybenzimidazole (PBI) as the polymeric binder. Here, flexible PBI-CUP PIC membranes with the thickness of ~135 μ m and CUP mass fraction of up to 75% were prepared by solution-casting without additional acid-doping (e.g., phosphoric acid). The proton conductivity of the fabricated IT-PIC-PEMs was up to 5.80 × 10 –2 S cm –1 as measured from a prototype IT PEM fuel cell (PEMFC) operated at 200 °C in the humidified hydrogen and air environment. This type of IT-PIC-PEMs also demonstrated sufficient mechanical strength and flexibility, excellent thermal stability (up to 350 °C), and very good durability of the proton conductivity (within the test duration of 500 h). The present experimental study shows the promising future of the IT-PIC-PEMs for applications in various IT electrochemical processes including IT-PEMFCs, IT-electrolyzers, etc.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Novel dense-PBI membranes for photoelectrochemical hydrogen production

Summary and main accomplishments 1. Screening of available polybenzimidazole (PBI) membranes for photoelectrochemical (PEC) hydrogen production. 2. Two main candidate membranes selected and synthesized. 3. Selected membranes characterized, including assessment of electrochemical properties (conductivity) and mechanical properties (creep and creep compliance). 4. Single cell PEC system successfully fabricated. 5. Electrochemical cell tested with initial water decomposition results obtained under ‘dark electrolysis’ conditions. 6. Recommendations given for future test and work.

Corgnale, Claudio [Greenway Energy; Greenway Energ↗

DOE OSTI2023

Development of a Pre-Combustion CO 2 Capture Process Using High-Temperature PBI Hollow-Fiber Membranes

The overall objective of this project was to evaluate the advantages of transformational polybenzimidazole (PBI) polymer hollow-fiber membrane (HFM)-based, carbon dioxide (CO 2 ) capture and purification technology at bench-scale using an actual coal-derived syngas stream from a coal gasification facility. The project was carried out over two budget periods. The technical objectives in Budget Period 1 (BP1) included preparing HFs and modules and upgrading the available skid for field testing. The technical objectives for BP2 were to field-test the skid unit with actual coal-derived syngas from an oxygen-blown gasifier to obtain performance data, update the Techno-Economic Analysis (TEA) that would assist with future process scale-up, and provide information on the design of a small pilot-scale test unit. The goal was to advance the PBI-HFM CO 2 capture and gas separation system for pre-combustion applications beyond second-generation economic performance predictions and make progress toward meeting overall fossil energy performance goals of CO 2 capture with 95% CO 2 purity at a cost of electricity (COE) 30% less than baseline capture approaches. The research program was designed with progressive technical tasks leading to both dynamic and steady-state testing of the PBI-HFM skid with actual coal-derived syngas. The work plan was to: (1) fabricate sufficient Generation-2 (GEN-2) fibers for module fabrication; (2) upgrade the fiber skid to accommodate large fiber modules for bench-scale field testing; (3) conduct dynamic and steady-state testing with coal-derived syngas from an oxygen-blown gasifier and obtain system performance data; (4) perform a TEA and environmental, health, and safety (EH&S) assessment; (5) update the State-Point Data Table, Technology Gap Analysis (TGA), and Technology Maturation Plan (TMP); (6) uninstall and return the test skid to the Recipient’s facilities; and (7) submit a Final Report that describes the results and analysis of the project research effort.

03 NATURAL GAS↗

DOE OSTI2023

Finely tuning the microporosity in phosphoric acid doped triptycene-containing polybenzimidazole membranes for highly permselective helium and hydrogen recovery

High-performance polymer membranes with well-defined microporosity and size-sieving ability are especially attractive for helium and hydrogen recovery. Here, in this study, we report novel macromolecular engineering of polybenzimidazole (PBI) membranes that integrate hierarchical triptycene units for high permeability and polyprotic acid doping for size sieving via controllable manipulation of microporous architecture. The triptycene moieties disrupt chain packing and introduce additional configurational free volume, leading to significantly boosted He and H 2 permeabilities compared to previously reported PBI membranes. The acid doping resulted in crosslinked PBI membranes via hydrogen bonding and proton transfer with dramatically enhanced gas selectivities. Via adjusting the H 3 PO 4 -doping level, triptycene-based polybenzimidazole (TPBI) composite membranes (TPBI-(H 3 PO 4 ) x ) exhibit the highest gas selectivities for He enrichment (i.e., α(He/CH 4 ) = 7052 ± 156) and H 2 purification (i.e., α(H 2 /CH 4 ) = 5128 ± 110) among existing polymeric gas separation membranes. Additionally, under mixed-gas conditions at 150 °C, the TPBI-(H 3 PO 4 ) 0.98 membrane displays a H 2 permeability of 46.7 Barrer and a H 2 /CO 2 selectivity of 16, far beyond the Robeson's 2008 upper bound for H 2 /CO 2 separation. The facile and diverse tunability and excellent gas separation performance make TPBI-(H 3 PO 4 ) x membranes highly attractive for helium and hydrogen separation.

42 ENGINEERING↗

DOE OSTI2025

Microporous pentiptycene-based polybenzimidazole membranes for high temperature H 2 /CO 2 separation

Separating H 2 from syngas at elevated temperatures (100–250 °C) have attracted significant attention in recent years as a means to reduce energy consumption and capital costs in precombustion carbon capture processes, such as those following steam reforming of natural gas or coal gasification. Polybenzimidazole (PBI), particularly m-PBI, has been reported as a leading membrane material for high-temperature H 2 /CO 2 separation. However, m-PBI exhibits extremely low H 2 permeability, even at high temperatures, which limits its productivity in H 2 /CO 2 separation applications. Here, to address this limitation, this work introduces a new pentiptycene-based polybenzimidazole (PPBI) featuring significantly enhanced H 2 permeability and attractive high-temperature H 2 /CO 2 separation performance, which stems from the unique configurational free volume elements introduced by pentiptycene moieties. Further tuning of the free volume architecture of PPBI films is achieved via acid doping with phosphoric acid (PA) or trans-aconitic acid (TaA), which introduces crosslinking among PPBI chains. Under mixed-gas environment (50/50 mol% H 2 /CO 2 ) at 180 °C, the acid-doped PPBI films exhibit a ∼230 % increase in H 2 /CO 2 selectivity compared to pristine PPBI film while maintaining high H 2 permeability that is nearly 500 % of m-PBI. These properties approach the predicted upper bound for membrane operating at 180 °C, highlighting its great potential for high-temperature H 2 /CO 2 separation.

Liu, Mengdi [University of Notre Dame, IN (United ↗

DOE OSTI2022

Polybenzimidazole-derived carbon molecular sieve hollow fiber membranes with tailored oxygen selective transport

Polymer membrane carbonization is a promising strategy to obtain carbon molecular sieve (CMS) membrane materials with tailorable cavity size distributions for high gas selectivities beyond that attained from traditional polymer membrane materials. Despite their already demonstrated exceptional separation performance characteristics for several gas separation applications (e.g. CO 2 /CH 4 and H 2 /CO 2 ), further development of CMS membranes having high O 2 /N 2 perm-selectivity for energy-efficient high-purity O 2 production has proven challenging. Herein, we explore CMS hollow fiber membranes (HFMs) derived from highly rigid and tightly-packed polybenzimidazole (PBI) materials. Nearly defect-free PBI-derived CMS HFMs were fabricated and evaluated for O 2 /N 2 separation performance for the first time. The micro-structural and O 2 selective gas separation characteristics of PBI-CMS HFMs pyrolyzed at different pyrolysis conditions were intensively studied. With rigorous carbonization protocol optimization, we obtained highly O 2 permselective PBI-CMS HFMs having O 2 /N 2 selectivities approaching 14, enabling high purity O 2 production. The PBI-CMS HFM O 2 /N 2 separation performance dependence on operating conditions (e.g. temperature and feed pressure) are reported.

36 MATERIALS SCIENCE↗

DOE OSTI2022

In Situ Growth of Crystalline and Polymer-Incorporated Amorphous ZIFs in Polybenzimidazole Achieving Hierarchical Nanostructures for Carbon Capture

We report mixed matrix materials (MMMs) hold great potential for membrane gas separations by merging nanofillers with unique nanostructures and polymers with excellent processability. In situ growth of the nanofillers is adapted to mitigate interfacial incompatibility to avoid the selectivity loss. Surprisingly, functional polymers have not been exploited to co-grow the nanofillers for membrane applications. Herein, in situ synergistic growth of crystalline zeolite imidazole framework-8 (ZIF-8) in polybenzimidazole (PBI), creating highly porous structures with high gas permeability, is demonstrated. More importantly, PBI contains benzimidazole groups (similar to the precursor for ZIF-8, i.e., 2-methylimidazole) and induces the formation of amorphous ZIFs, enhancing interfacial compatibility and creating highly size-discriminating bottlenecks. For instance, the formation of 15 mass% ZIF-8 in PBI improves H- 2 permeability and H- 2 /CO 2 selectivity by approximate to 100% at 35 degrees C, breaking the permeability/selectivity tradeoff. This work unveils a new platform of MMMs comprising functional polymer-incorporated amorphous ZIFs with hierarchical nanostructures for various applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2023

Few-cycle atomic layer deposition to nanoengineer polybenzimidazole for H 2 /CO 2 separation

Atomic layer deposition (ALD) creates uniform sub-nanometer films on a variety of surfaces and nanopore walls and has been used to modify polymers to improve surface affinity towards specific molecules, solvent resistance, and barrier properties to gases and vapors. Here, for the first time, we demonstrate that few-cycle ALD can be used to engineer functional polymers at a sub-nanometer scale to improve both molecular size-sieving ability and counterintuitively, gas permeability. Particularly, 1-cycle ALD treatment of polybenzimidazole (PBI) by sequential exposure to trimethylaluminum (TMA) and water vapor remarkably increases H 2 permeability by 120% - 270% and H 2 /CO 2 selectivity by 30% at 35–200 °C. The ALD not only deposits an AlOx layer on the surface but also enables the TMA to infiltrate and react with the bulk PBI to form an AlO x network, disrupting polymer chain packing and increasing chain rigidity. The membrane exhibits excellent stability when challenged with simulated syngas, overcoming the permeability/selectivity tradeoff for H 2 /CO 2 separation. In conclusion, this study showcases a facile and scalable way of engineering polymeric membranes at a sub-nanometer level to improve molecular separation performance.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Facilely Cross-Linking Polybenzimidazole with Polycarboxylic Acids to Improve H 2 /CO 2 Separation Performance

Polybenzimidazole (PBI) with a strong size-sieving ability exhibits attractive H 2 /CO 2 separation properties for blue H 2 production and CO 2 capture. Herein, we report that PBI can be facilely cross-linked with polycarboxylic acids, oxalic acid (OA), and trans-aconitic acid (TaA) to improve its separation performance. The acids react with the amines on the PBI chains, decreasing free volume and increasing size-sieving ability. The acid doping increases H 2 /CO 2 selectivity from 12 to as high as 45 at 35 °C. Here, the acid-doped samples demonstrate stable H 2 /CO 2 separation performance when challenged with simulated syngas containing water vapor at 150 °C, which surpasses state-of-the-art polymers and Robeson’s upper bound for H 2 /CO 2 separation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Proton Selective Nanoporous Atomically Thin Graphene Membranes for Vanadium Redox Flow Batteries

Angstrom-scale proton-selective pores in atomically thin 2D materials present fundamentally new opportunities for advancing proton exchange membranes (PEMs). Vanadium Redox Flow Batteries (VRFBs) for grid-scale energy storage require PEMs with high areal proton conductance (>1 S cm −2 ) and minimal vanadium ion (VO 2+ ) crossover. However, state-of-the-art Nafion 212 membranes (N212 ≈50 µm thick), suffer from persistent VO 2+ crossover reducing performance and efficiency. Here, a layered PEM is demonstrated, comprising monolayer CVD graphene with Angstrom-scale proton-selective pores introduced via Ar plasma, integrated with an ultra-thin ≈300 nm polybenzimidazole (PBI) layer and sandwiched between two Nafion 211 (25 µm thick) layers. The layered architecture facilitates scalable membrane fabrication by mitigating defects while processing and facile stacking of graphene layers allows stochastic non-selective defect isolation enabling exceptionally low VO 2+ crossover (selectivity (H + areal conductance / VO 2+ permeability) ≈6709 × 10 6 S min cm −4 ), with proton conductance >8 S cm −2 . Systematic transport experiments supported by resistance-based transport modelling elucidate the role of defect size, defect isolation, and sealing, as well as layering/stacking, to enable orders of magnitude (>671× over N212) improvements in selectivity, along with areal proton conductance >8 S cm −2 . This work highlights the potential of atomic-scale proton-selective defect engineering in 2D materials, in conjunction with facile stacking and layering of materials as strategies for scalable, high-performance advances in PEMs for energy, electrochemical, and separation applications beyond VRFBs.

Chaturvedi, Pavan [Vanderbilt Univ., Nashville, TN↗