Search NASA⌕ Search

SEARCH · Search NASA

Results for “powered-lift aircraft”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Flight-path and airspeed control during landing approach for powered-lift aircraft

Manual control of flight path and airspeed during landing approach has been investigated for powered-lift transport aircraft. An analysis was conducted to identify the behavior of the aircraft which would be potentially significant to the pilot controlling flight path and airspeed during the approach. The response characteristics found to describe the aircraft behavior were (1) the initial flight-path response and flight-path overshoot for a step change in thrust, (2) the steady-state coupling of flight path and airspeed for a step change in thrust, and (3) the sensitivity of airspeed to changes in pitch attitude. The significance of these response characteristics was evaluated by pilots on a large-motion, ground-based simulator at Ames Research Center. Coupling between flight path and airspeed was considered by the pilot to be the dominant influence on handling qualities for the approach task. Results are compared with data obtained from flight tests of three existing powered-lift V/STOL aircraft.

Franklin, J. A.↗
NASA NTRS1974

A simulator investigation of engine failure compensation for powered-lift STOL aircraft

A piloted simulator investigation of various engine failure compensation concepts for powered-lift STOL aircraft was carried out at the Ames Research Center. The purpose of this investigation was to determine the influence of engine failure compensation on recovery from an engine failure during the landing approach and on the precision of the STOL landing. The various concepts include: (1) cockpit warning lights to cue the pilot of an engine failure, (2) programmed thrust and roll trim compensation, (3) thrust command and (4) flight-path stabilization. The aircraft simulated was a 150 passenger four-engine, externally blown flap civil STOL transport having a 90 psf wing loading and a .56 thrust to weight ratio. Results of the simulation indicate that the combination of thrust command and flight-path stabilization offered the best engine-out landing performance in turbulence and did so over the entire range of altitudes for which engine failures occurred.

Nieuwenhuijse, A. W.↗
NASA NTRS1974

Parameter estimation of powered-lift STOL aircraft characteristics including turbulence and ground effects

The estimation of longitudinal aerodynamic coefficients from data recorded during flight tests of a powered-lift STOL aircraft is considered. First, a comparison is made between the coefficient values determined by the regression and quasilinearization identification techniques from records taken during elevator pulse maneuvers. The results show that for these tests the regression method provides less scatter in coefficient estimates and provides better correlation with the predicted values. Special techniques are then developed which allow identification of the coefficients from records taken during landing maneuvers in which the aircraft encounters turbulence while flying in ground effect. Flight test results are presented to illustrate the effects of air turbulence and ground proximity on the estimated coefficient values.

Wingrove, R. C.↗
NASA NTRS1973

Approach path control for powered-lift STOL aircraft

A flight control system concept is defined for approach flightpath control of an augmentor wing (or similar) powered-lift STOL configuration. The proposed STOL control concept produces aircraft transient and steady-state control responses that are familiar to pilots of conventional jet transports, and has potential for good handling qualities ratings in all approach and landing phases. The effects of trailing-edge rate limits, real-engine dynamics, and atmospheric turbulence are considered in the study. A general discussion of STOL handling qualities problems and piloting techniques is included.

Clymer, D. J.↗
NASA NTRS1974

Noise of model target type thrust reversers for engine-over-the-wing applications

The present work reports on experiments concerning the noise generated by V-gutter and semicylindrical target reversers with circular and short-aspect-ratio slot nozzles having equivalent diameters of about 5 cm. At subsonic jet velocities of interest for engine-over-the-wing (OTW) powered-lift aircraft, the reversers were noisier than the nozzles alone and had a more uniform directional distribution and more high-frequency noise. Reverser shape was more important than nozzle shape in determining the reverser noise characteristics. An estimate is made of perceived noise level along the 152-m sideline for a hypothetical OTW powered-lift airplane.

Stone, J. R.↗
NASA NTRS1974

The augmentor wing - Powered-lift STOL a proven concept

A jet-STOL powered-lift aircraft has the ability to perform a relatively steep (7.5 deg) final approach at high power setting and a low speed. The DHC-5 Buffalo/Spey Augmentor-Wing research aircraft is the first machine of its kind to accomplish this performance. The aircraft uses an approach in which the cold bypass thrust is vectored by the augmentor flap. Aspects of aircraft reliability are discussed together with taxi trials, stalling characteristics, lateral directional control, single-engine operations, roll acceleration, and flight in turbulent conditions.

Whittley, D. C.↗
NASA NTRS1974

Analytical design and simulation evaluation of an approach flight director system for a jet STOL aircraft

A program was undertaken to develop design criteria and operational procedures for STOL transport aircraft. As part of that program, a series of flight tests shall be performed in an Augmentor Wing Jet STOL Aircraft. In preparation for the flight test programs, an analytical study was conducted to gain an understanding of the characteristics of the vehicle for manual control, to assess the relative merits of the variety of manual control techniques available with attitude and thrust vector controllers, and to determine what improvements can be made over manual control of the bare airframe by providing the pilot with suitable command guidance information and by augmentation of the bare airframe dynamics. The objective of the study is to apply closed-loop pilot/vehicle analysis techniques to the analysis of manual flight control of powered-lift STOL aircraft in the landing approach and to the design and experimental verification of an advanced flight director display.

Klein, R. H.↗
NASA NTRS1972

Computer programs for estimation of STOL takeoff, landing, and static performance

A set of computer programs has been developed for evaluating the performance of powered-lift STOL aircraft. Included are a static performance summary and dynamic calculations of takeoff and landing performance. The input, output, options, and calculations for each program are described. The programs are written in FORTRAN IV and are currently available on TSS 360. Three independent sections are presented corresponding to the three programs: (1) static performance, (2) takeoff performance, and (3) landing performance.

Post, S. E.↗
NASA NTRS1973

Computer programs for estimating aircraft takeoff and landing performance

A set of computer programs has been developed to estimate the takeoff and landing maneuver of a given aircraft. The program is applicable to conventional, vectored lift and powered-lift concept aircraft. Portions of the program may also be used to evaluate the static performance of these types of aircraft. The aircraft is treated as a point mass confined to motion in a vertical plane, and rotational dynamics have been neglected. The required input is described and a sample case is presented.

Bowles, J. V.↗
NASA NTRS1972

Simulator evaluation of the flying qualities of externally blown flap and augmentor wing transport configurations

Concurrent simulations of powered-lift STOL transport aircraft having either an externally blown flap configuration or an augmentor wing configuration were conducted. The following types of simulators of varying sophistication were used: (1) a simple fixed-base simulation with a simple visual display, (2) a more complex fixed-base simulation using a realistic transport cockpit and a high-quality visual display, and (3) a six-degree-of-freedom motion simulator that had a realistic transport cockpit and a sophisticated visual display. The unaugmented flying qualities determined from these simulations were rated as unacceptable for both the externally blown flap and augmentor wing configurations. The longitudinal, lateral-directional, and single-engine-failure characteristics were rated satisfactory with extensive augmentation, including pitch and roll command systems, flight-path (or speed) augmentation, turn coordination, and effective yaw damping. However, the flare and landing characteristics from any approach glide-path angle in excess of 4 deg were rated as unsatisfactory but acceptable.

Kier, D. A.↗
NASA NTRS1973

Air transportation noise technology overview

The NASA and DOT technology program planning for quieter air transportation systems is reviewed. To put this planning in context, the nature of the noise problem and the projected nature of the air transportation fleet are identified. The technology program planning reviewed here is discussed in relation to the following areas of activity: systems analysis, community acceptance, basic research and technology, and the various classes of civil aircraft, i.e. existing and advanced transports, powered-lift transports, and general aviation.

Maggin, B.↗
NASA NTRS1974

Comparison of the acoustic characteristics of large-scale models of several propulsive-lift concepts

Wind-tunnel acoustic investigations were performed to determine the acoustic characteristics and the effect of forward speed on the over-the-wing externally blown jet flap (OTW), the under-the-wing externally blown jet flap (UTW), the internally blown jet flap (IBF), and the augmentor wing (AW). The data presented represent the basic noise generated by the powered-lift system without acoustic treatment, assuming all other noise sources, such as the turbofan compressor noise, have been suppressed. Under these conditions, when scaled to a 100,000-lb aircraft, the OTW concept exhibited the lowest perceived noise levels, because of dominant low-frequency noise and wing shielding of the high-frequency noise. The AW was the loudest configuration, because of dominant high-frequency noise created by the high jet velocities and small nozzle dimensions. All four configurations emitted noise 10 to 15 PNdB higher than the noise goal of 95 PNdB at 500 ft.

Falarski, M. D.↗
NASA NTRS1974

Longitudinal aerodynamic characteristics of an externally blown flap powered lift model with several propulsive system simulators

An investigation of a four-engine externally blown flap (EBF) powered-lift transport was conducted in the Langley V/STOL tunnel to determine the effect of different engine configurations on the longitudinal aerodynamic characteristics. The different engine configurations were simulated by five different sets of propulsion simulators on a single aircraft model. Longitudinal aerodynamic data were obtained for each simulator on each flap deflection corresponding to cruise, take-off, and landing at a range of angles of attack and various thrust coefficients. The bypass ratio (BPR) 6.2 engine simulator provided the best lift and drag characteristics of the five simulators tested in the take-off and landing configurations. The poor performance of the BPR 10.0 and 3.2 engine simulators can be attributed to a mismatch of engine-model sizes or poor engine location and orientation. Isolated engine wake surveys indicated that a reasonable assessment of the aerodynamic characteristics of an engine-wing-flap configuration could be made if qualitative information were available which defined the engine wake characteristics. All configurations could be trimmed easily with relatively small horizontal-tail incidence angles; however, the take-off landing configurations required a high-lift tail.

Hoad, D. R.↗
NASA NTRS1972

Use of the flight simulator in the design of a STOL research aircraft.

Piloted simulator tests on the NASA-Ames Flight Simulator for Advanced Aircraft motion base played a major role in guiding the design of the Modified C-8A 'Buffalo' augmentor wing jet flap STOL research airplane. Design results are presented for the flight control systems, lateral-directional SAS, hydraulic systems, and engine and thrust vector controls. Emphasis is given to lateral control characteristics on STOL landing approach, engine-out control and recovery techniques in the powered-lift regime, and operational flight procedures which affected airplane design.

Spitzer, R. E.↗
NASA NTRS1975

Forward velocity effects on under-the-wing externally blown flap noise

Noise tests were conducted with small-scale models of externally blown-flap powered-lift systems that were subjected to simulated takeoff and landing free-stream velocities by placing the nozzle-wing models in a free jet. The nozzle configurations consisted of a conical and an 8-tube mixer nozzle. The results show that the free-stream velocity attenuates the noise from the various configurations, with the amount of attenuation depending on the flap setting. More attenuation was obtained with a flap setting of 20 degrees than with a flap setting of 60 degrees. The dynamic effect on the total attenuation caused by aircraft motion is also discussed.

Goodykoontz, J.↗