Search NASA⌕ Search

SEARCH · Search NASA

Results for “preparation methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Preparation Methods: past and Potential Methods of Food Preparation for Space

The logical progression of development of space food systems during the Mercury, Gemini, Apollo, Skylab and Shuttle programs is outlined. The preparation methods which include no preparation to heating, cooling and freezing are reviewed. The introduction of some new and exciting technological advances is proposed, which should result in a system providing crew members with appetizing, safe, nutritious and convenient food.

Huber, C. S.↗
DOE OSTI2023

Sample Preparation Methods for Targeted Single-Cell Proteomics

We compared three cell isolation and two proteomic sample preparation methods for single-cell and near-single-cell analysis. Whole blood was used to quantify hemoglobin (Hb) and glycated-Hb (gly-Hb) in erythrocytes using targeted mass spectrometry and stable isotope-labeled standard peptides. Each method differed in cell isolation and sample preparation as follows: 1) FACS and automated preparation in one-pot for trace samples (autoPOTS); 2) limited dilution via microscopy and a novel rapid one-pot sample preparation method that circumvented the need for the solid-phase extraction, low-volume liquid handling instrumentation and humidified incubation chamber; and 3) CellenONE-based cell isolation and the same one-pot sample preparation method used for limited dilution. Only the CellenONE device routinely isolated single-cells from which Hb was measured to be 540–660 amol per red blood cell (RBC), which was comparable to the calculated SI reference range for mean corpuscular hemoglobin (390–540 amol/RBC). FACSAria sorter and limited dilution could routinely isolate single-digit cell numbers, to reliably quantify CMV-Hb heterogeneity. Finally, we observed that repeated measures, using 5–25 RBCs obtained from N = 10 blood donors, could be used as an alternative and more efficient strategy than single RBC analysis to measure protein heterogeneity, which revealed multimodal distribution, unique for each individual.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS2013

High Energy, Low Temperature Gelled Bi-propellant Formulation Preparation Method

A method for preparing a gelled liquid propane (GLP) composition comprises the introduction of liquid propane into an evacuated mixing vessel containing a gellant and mixing the liquid propane with the gellant. A bi-propellant system comprising GLP is particularly well-suited for outer planet missions greater than 3 AU from the sun and also functions in earth and near earth environments. Additives such as powders of boron, carbon, lithium, and/or aluminum can be added improve performance or enhance hypergolicity. The gelling agent can be silicon dioxide, clay, carbon, or organic or inorganic polymers. The bi-propellant system may be, but need not be, hypergolic.

DiSalvo, Roberto↗
DOE OSTI2022

Impact of specimen preparation method on photovoltaic backsheet degradation during accelerated aging test

In this study, we highlight some important factors in the specimen preparation methods for evaluating photovoltaic backsheet properties after accelerated aging. Two different sequences are considered: Method (I) cut-then-age: cut into 1-cm wide strips and then expose to stress, and Method (II) age-then-cut: expose a larger sheet to stress and then cut into 1-cm widths for mechanical property measurements. We also compare the effect of three cutting methods, (a) tensile specimen punch, (b) paper cutter, and (c) fresh razor blade. Several commercial backsheets were evaluated, with stress exposures including (a) pressure cooker test (PCT), (b) dry ultraviolet (UV) radiation exposure, and (c) UV combined damp heat tests. Fourier transform infrared spectrometer (FTIR) and intrinsic viscosity (IV) were used to analyze the materials on unstressed materials and samples exposed to PCT. The results show that both the cutting method and the time of cutting have an impact on the backsheet mechanical properties. Additionally, under UV exposure, Method II, age-then-cut, generally resulted in a higher average value, with more variation than Method I; however, if the side strips from Method II were excluded, the variation dropped to the same level. This is because the specimens at the sides of the sheet get additional damage from UV light from the exposed sides of the sample. In contrast to UV exposure, PCT specimens prepared by Method II result in lower average values and higher variability. This is attributed to embrittlement through the bulk of the sample where the cutting of embrittled specimens appears to result in more edge defects which can then initiate a break at smaller strains. The data suggest that for UV exposures, the specimens should be cut after aging and the exposed side specimens discarded, and that for PCT exposures, the specimens should be cut before the exposure.

14 SOLAR ENERGY↗
DOE OSTI2023

Sample Preparation Method for Low-Level Total 129 I Measurements by ICP-MS

Trace-level measurements of iodine’s isotopic ( 129 I and 127 I) and chemical species distributions are needed for an accurate understanding of radioiodine migration in the Hanford subsurface. Pacific Northwest National Laboratory (PNNL) previously developed a novel analytical method for iodine characterization that uses ion chromatography (IC) coupled to inductively coupled mass spectrometry (ICP-MS). While the method can measure speciated forms of 129 I at levels below the drinking water standard, an interference from molybdenum (Mo) prevents the assay from quantifying the $\underline{total}$ 129 I concentration in many Hanford sample matrices. In this work, solvent extraction was evaluated as a sample preparation method for eliminating the Mo interference. A series of 10 experiments was conducted in which solutions containing known amounts of iodate or iodide were treated by solvent extraction, and the extracted solutions were analyzed for total iodine concentrations by ICP MS. Several extraction parameters such as reagent concentrations and chemical reaction times were systematically adjusted in attempts to optimize the extraction process. While solvent extraction was shown to be effective at removing Mo, there was a consistent inability to recover more than approximately 75% of the total iodine in most experiments. This would reduce the ability to detect 129 I at levels near the drinking water standard. Additionally, the extraction efficiencies in several experiments were highly variable, suggesting that solvent extraction could add significant uncertainty to radioiodine measurements. We recommend evaluating ion exchange as an alternative sample preparation approach in fiscal year (FY) 2024.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Effects of Serum and Compound Preparation Methods on Delayed Repolarization Evaluation With Human iPSC-CMs

Abstract Human induced pluripotent stem cell-derived cardiomyocytes (hiPSC-CMs) have been widely used in the Comprehensive in vitro Proarrhythmia Assay (CiPA). The notable difference of the electrophysiological (EP) responses of hiPSC-CMs in serum and serum-free media (SFM) is puzzling and may impact regulatory decision-making on the cardiac safety of candidate drugs in inducing QT prolongation and torsade de pointes (TdP). In this study, we compared the EP responses of hiPSC-CMs to 10 CiPA compounds and moxifloxacin in serum and SFM; explained the potential reason behind the different EP responses—abiotic compound loss to plastic tubes/plates of hydrophobic compounds prepared in SFM; and investigated the impact of compound preparation methods on drug bioavailability in exposure media, which affects the TdP risk prediction of drugs tested in serum-containing and SFM. For assays to be conducted in SFM, awareness of abiotic compound loss of hydrophobic compounds in serum-free preparations is critical for delay repolarization evaluation and data extrapolation from in vitro to in vivo.

Toxicology↗
DOE OSTI2022

Optimization of Preparation Method, Nucleating Agent, and Stabilizers for Synthesizing Calcium Chloride Hexahydrate (CaCl2.6H2O) Phase Change Material

This study investigates improvements in low-cost latent heat storage material calcium chloride hexahydrate (CaCl2.6H2O). Its melting point is between 25 and 28 °C, with relatively high enthalpy (170–190 J/g); however, this phase change material (PCM) shows supercooling and phase separation. In CaCl2.6H2O incongruent melting causes lower hydrates of CaCl2 to form, which affects the overall energy storage capacity and long-term durability. In this work, PCM performance enhancement was achieved by adding SrCl2.6H2O as a nucleating agent and NaCl/KCl as a stabilizer to prevent supercooling and phase separation, respectively. We investigated the PCM preparation method and optimized the proportions of SrCl2.6H2O and NaCl/KCl. Thermal testing for 25 cycles combined with DSC and T-history testing was performed to observe changes in enthalpy, phase transitions and supercooling over the extended period of usage. X-ray diffraction was used to verify crystalline structure in the compounds. It was found that the addition of 2 wt.% of SrCl2.6H2O reduced supercooling from 12 °C to 0 °C compared to unmodified CaCl2.6H2O. The addition of 5 wt.% NaCl or KCl proved to effectively suppress separation and the melting enthalpy achieved was 169 J/g–178 J/g with congruent melting over 25 cycles, with no supercooling and almost no reduction in the latent heat.

42 ENGINEERING↗
DOE OSTI2020

Structure and activity of supported bimetallic NiPd nanoparticles: influence of preparation method on CO 2 reduction

Here, bimetallic Ni-Pd and monometallic reference catalysts were prepared by decomposing organometallic precursors, Ni(cod) 2 and Pd 2 (dba) 3 , leading to nanoparticles with sizes ranging from 3 to 6 nm. Two different synthesis procedures were followed: i) solution synthesis using capping ligand (hexadecylamine) followed by impregnation of pre-formed nanoparticles on SiO 2 , called Sol-immobilization (SI); and 2) direct precursor decomposition onto SiO 2 , without stabilizer, called Direct Decomposition (DD). Samples prepared by SI procedure are alloyed bimetallic nanoparticles, whereas samples obtained by DD one show phase segregation. Interestingly, DD samples show better activity for CO 2 hydrogenation into CO (reverse water-gas shift reaction - RWGS) than SI ones. The best compromise between activity for CO 2 activation (at lower temperature) and CO selectivity was achieved with Ni DD and NiPd DD catalysts. Moreover, the addition of palladium increased the concentration of surface undercoordinated sites, which chemisorb CO weakly, thus improving activity and selectivity, in opposition to other samples that chemisorb CO strongly, in multiband configuration. In the presence of Pd, different decomposition rates drive the formation of smaller and more active Ni clusters. The knowledge acquired here on the influence of synthesis conditions on the catalytic properties of Ni-Pd catalysts should guide us to better catalysts for CO 2 transformations into valuable products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRSDate not supplied

Investigating Waste Preparation Methods for Trash-to-Gas Technologies

Trash-to-Gas technologies show promise in addressing the need for a proper waste management system onboard a long-duration space mission. However, there is a clear need to better understand how the initial waste preparation can affect the overall conversion efficiency. Factors such as the waste size, moisture content, and packing density can have significant impacts on the reactor performance. This paper will focus on the effects of various pre-processing steps on the overall solid-to-gas conversion on the state of the art Trash-to-Gas system developed at NASA Kennedy Space Center. These results will help inform future Trash-to-Gas technologies on what types of supporting subsystems will be necessary to operate effectively for exploration missions.

Trash to Gas↗
NASA NTRSDate not supplied

Investigating Waste Preparation Methods for Trash-to-Gas Technologies

Trash-to-Gas technologies show promise in addressing the need for a proper waste management system onboard a long-duration space mission. However, there is a clear need to better understand how the initial waste preparation can affect the overall conversion efficiency. Factors such as the waste size, moisture content, and packing density can have significant impacts on the reactor performance. This paper will focus on the effects of various pre-processing steps on the overall solid-to-gas conversion on the state of the art Trash-to-Gas system developed at NASA Kennedy Space Center. These results will help inform future Trash-to-Gas technologies on what types of supporting subsystems will be necessary to operate effectively for exploration missions.

Trash to Gas↗
DOE OSTI2021

An improved specimen preparation method for marine shallow gas-bearing sand sediments and its validations

Instabilities of shallow gas-charged seabed are potential geological hazards in ocean engineering. In practice, the conventional field sampling techniques failed to obtain undisturbed gas-bearing sediments from the seabed for laboratory mechanical testing because of sensitive gas exsolution and escape from sediments. However, preparation of representative remoulded gas-charged specimens is a challenging issue, because it is rather difficult to quantitatively control the gas content and obtain uniform distribution of gas bubbles within the specimen. Given the above problems, this work proposes a reliable approach to reconstitute the high-saturation specimen of gas-charged sediments in the laboratory by an improved multifunction integrated triaxial apparatus (MITA). This apparatus is developed based on an advanced stress path triaxial system by introducing a temperature-controlled system and a wave-monitoring system. The temperature-controlled system is used to accurately mimic the in situ environments of sediments in the seabed. The wave-monitoring system is utilized to identify exsolution point of free gas and examine the disturbance of gas to specimens during gas exsolution. The detailed procedure of gassy specimen preparation is introduced. Then, the quality of prepared specimens using our improved apparatus is validated by the high-resolution micro-X-ray computed tomography (μCT) scanning test, from which bubble occurrence and size distribution within the gassy sand specimen can be obtained; and preliminary mechanical tests on gassy sand specimens with various initial saturation degrees are performed. The proposed specimen preparation procedure succeeds in proving the postulated occurrence state of gas bubbles in coarse-grained sediments and accurately controlling the gas content.

58 GEOSCIENCES↗
DOE OSTI2025

Development of Transformative Preparation Methods to Push up High Q&G Performance of FRIB Spare HWR Cryomodule Cavities

The FRIB accelerator project construction, a top priority of US nuclear science, was completed in January 2022, and is now moving to user operation. The stable and reliable operation of the accelerating cryomodules is essential in achieving/fulfilling DOE and user expectations. So far, FRIB cryomodules meet all FRIB specifications for cavity performance. However, during the lifetime of machine operation, degradation of cryomodule performance is possible, as reported in similar operating facilities (CEBAF, SNS). If cryomodule degradation is observed at FRIB, the under-performing cryomodule will require replacement/maintenance. In effort to manage operational reliability, FRIB plans to construct a 0.53 half-wave cryomodule to serve as an active spare. In a parallel effort, FRIB will also work toward increasing operational Q and gradient of spare cryomodule cavities to gain an overall performance margin to support future operational reliability. The current FRIB cavity designs have a potential to operate at gradients higher than 8 MV/m, but are currently limited by field emission (FE) and/or high field Q slope (HFQS); known issue in buffered chemical polished (BCP) treated cavities. The proposal looks to develop transformative surface preparation treatments to improve the operational gradient of spare cryomodules higher than 10 MV/m while maintaining high Q. Thus, increasing operational margin by 30 - 50%. With the goal to improve operational reliability set, the proposal will investigate multiple objectives as possible paths forward to achieve an overall increase in cavity performance and gain a better understanding of SRF limiting mechanisms. The proposal will study the application of different chemical surface treatments to 0.53 half-wave cavities, with the addition of low temperature bakes (LTB), and measure their effects on accelerating performance. Proposed chemical treatments to be explored in this proposal include conventional EP acid mixtures, as well as innovated EP and BCP acid mixtures designed to simplify processing paths in migrating FE and HFQS. The proposed transformative treatment wet N-doping also has the potential to replicate recent advancements in SRF technology relating to nitrogen doping and high Q operation without the requirement for an ultra-high vacuum annealing furnace; currently being developed at FNAL and JLAB. In parallel, high Q performance relating to flux trapping will be investigated with the installation of a second layer of magnetic shielding in the vertical test Dewar. The research objectives presented in the proposal, and their corresponding effects on cavity performance, will provide essential knowledge and future guidance to the SRF community and provide possible paths for future SRF based projects and applications.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Surface preparation method for investigating the three-dimensional electronic structure of perovskite nickelates

The investigation of the electronic structures on perovskite oxides using surface-sensitive spectroscopy techniques is often hindered by their “uncleavable” nature, typically requiring expensive and complex in situ experimental setups that integrate the capabilities of sample synthesis and spectroscopy measurement under ultrahigh vacuum condition. Here, we address this challenge by developing an ozone-annealing process that yields atomically flat surfaces on perovskite oxide thin films, making them suitable for high-resolution angle-resolved photoemission spectroscopy measurements. Using this method, we present a three-dimensional electronic structure study of Nd 1−𝑥 ⁢Sr 𝑥 ⁢NiO 3 (𝑥=0 and 0.175) thin films with unprecedented accuracy. The experimentally determined low-energy fermiology exhibits quantitative agreements with two-band tight-binding simulations, which is further validated by first-principles calculations considering the material's actual crystal structure. This work provides an accessible approach for ex situ ARPES measurements on perovskite oxides and other strongly correlated oxides, including the recently discovered high-𝑇 c nickelates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1972

New methods for preparing N,N-dialkyltrifluoroacetamides

The customary preparative methods for N,N-dialkyltrifluoroacetamides involve the acylation of an amine by trifluoroacetic acid or its derivatives. The synthesis of N,N-dialkyltrifluoroacetamides by reacting trifluoroacetic anhydride or acid with disubstituted formamides and acetamides is discussed. These reactions were interpreted with the aid of gas chromatographic analysis. Different reaction mechanisms are proposed for the reactions of formamides and acetamides with trifluoroacetic anhydride or acid. The use of the proposed reaction mechanisms for the synthesis of other fluorinated compounds is discussed.

Hsu, L.↗
NASA NTRS1972

New methods for preparing n, n-dialkyltrifluoroacetamides

The customary preparative methods for N,N-dialkyltrifluoroacetamides involve the acylation of an amine by trifluoroacetic acid or its derivatives. In this report the synthesis of N,N-dialkyltrifluoroacetamides by reacting trifluoroacetic anhydride or acid with disubstituted formamides and acetamides is discussed. These reactions are interpreted with the aid of gas chromatographic analysis. Different reaction mechanisms are proposed for the reactions of formamides and acetamides with trifluoroacetic anhydride or acid. The use of the proposed reaction mechanisms for the synthesis of other fluorinated compounds is discussed.

Hsu, L.↗
DOE OSTI2020

Borophenes, boron layer allotropes and methods of preparation

A method of preparing an atomically-dimensioned elemental boron allotrope includes providing a substrate at a temperature greater than about 200° C.; generating elemental boron vapor from a solid elemental boron source; and contacting said substrate with said boron vapor for at least one of a rate and at a pressure sufficient to deposit on said substrate a boron allotrope comprising an elemental boron layer comprising a boron atomic thickness dimension, said method under negative pressure.

Hersam, Mark C.↗