Search NASA⌕ Search

SEARCH · Search NASA

Results for “pressure oscillation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Large-eddy simulation study on cycle-to-cycle variation of knocking combustion in a spark-ignition engine

The cycle-to-cycle variation in the knock intensity is commonly encountered under abnormal combustion conditions. The severity of these abnormal combustion events can vary significantly, and the efficiency of engines at high loads is limited in practice by heavy knocking phenomena. Since, a thorough analysis of such recurrent but non-cyclic phenomena via experiments alone becomes highly cumbersome, in the present work, a multi-cycle large-eddy simulation study was performed to quantitatively predict cyclic variability in the combustion process and cyclic knock intensity variability in a direct injection spark-ignition engine. To account for the turbulence-chemistry interaction effects on flame propagation, the G-equation combustion model was used. Detailed chemistry was solved outside the flame front with a toluene primary reference fuel skeletal kinetic mechanism. For both the mild knock and heavy knock conditions, the numerical results were validated against experimental measurements. Based on the simulation results, a correlation analysis was performed considering combustion phasing, peak cylinder pressure and maximum amplitude of pressure oscillation. Furthermore, a detailed three-dimensional spatial analysis illustrated the evolution of auto-ignition kernel development and propagation of pressure waves during knocking combustion for three typical cycles with different knock intensities. In this process, it was found that an early occurrence of auto-ignition in the end gas was prone to high knock intensity. Although multiple auto-ignition kernels were observed in different cycles, the degree of coupling between chemical heat release and pressure waves varied, thereby leading to different maximum amplitude of pressure oscillation values.

42 ENGINEERING↗
DOE OSTI2020

Bulk modulus measurement at mHz frequencies and high-pressure using synchrotron x-ray radiation

We report an experimental protocol for measuring the frequency dependence of the bulk modulus carried out in a synchrotron x-ray facility based multi-anvil high-pressure apparatus. An oscillating pressure perturbation characterized by x-ray diffraction produces a volume strain measured by imaging. Together, these yield the bulk modulus of the sample. In this work, we report data at 3 mHz as an example of the possibility of providing these data for the frequency range of 1 mHz–100 mHz.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Control of Large-Amplitude Combustion Oscillations Using Nanosecond Repetitively Pulsed Plasmas

This paper details the use of nanosecond repetitively pulsed discharges to attenuate combustion instabilities in a 14 kW swirl-stabilized methane/air combustor. The combustor exhibits large-amplitude pressure oscillations ranging from 1 to 4% of the mean pressure during which the flame exhibits bulk motion in each instability cycle, upstream and downstream, as revealed by high-speed chemiluminescence. Control is accomplished with an electrode comprising a pin anode at the centerline of the combustor, allowing a nanosecond spark to be generated in a region spanning close to the flame base, through the shear layers of the swirling flow and ending at the metallic combustor wall. The discharges are generated using 20 kV, 9 kHz pulses; and they correspond to about 120 W of mean power. This results in a suppression of the peak amplitude of the pressure oscillations by a factor of two to four, and 5 dB in the rms value. Using phase-averaged visualizations of the flame with and without plasma, we detail the sequence of flame motion in the course of the instability. With the plasma active, this reveals significant interactions between the flame and the plasma during the suppression. Finally, we present a state-space model of the thermoacoustic system, and we demonstrate open-loop control of the instabilities.

Engineering↗
DOE OSTI2020

Significance of the Direct Excitation Mechanism for High-Frequency Response of Premixed Flames to Flow Oscillations

Premixed flames are sensitive to flow disturbances, which can arise from acoustic or vortical fluctuations. For transverse instabilities, it is known that a dominant mechanism for flame response is “injector coupling,” whereby pressure oscillations associated with transverse waves excite axial flow disturbances. These axial flow disturbances then excite heat release oscillations. The objective of this paper is to consider another mechanism—the direct sensitivity of the unsteady heat release to transverse acoustic waves—and to compare its significance relative to the induced axial disturbances, in a linear framework. The rate at which the flame adds energy to the disturbance field is quantified using the Rayleigh criterion and evaluated over a range of control parameters, such as flame length and swirl number. The results show that radial modes induce heat release fluctuations that always add energy to the acoustic field, whereas heat release fluctuations induced by mixed radial-azimuthal modes can add or remove energy. These amplification rates are then compared to the flame response from induced axial fluctuations. For combustor-centered flames, these results show that the direct excitation mechanism has negligible amplification rates relative to the induced axial mechanism for radial modes. For transverse modes, the fact that the nozzle is located at a pressure node indicates that negligible induced axial velocity disturbances are excited; as such, the direct mechanism dominates. As a result, for flames that are not centered on pressure nodes, the direct mechanism for mixed modes dominates for certain nozzle locations and flame angles.

42 ENGINEERING↗
DOE OSTI2023

Effects of knock intensity measurement technique and fuel chemical composition on the research octane number (RON) of FACE gasolines: Part 2 – Effects of spark timing

The Research and Motor Octane Number (RON, MON) characterize a fuel’s knock resistance by rating the knock intensity of a sample fuel relative to that of Primary Reference Fuels (PRF) in a Cooperative Fuel Research (CFR) Engine. A fuel’s octane number is regulated to prevent damage from autoignition leading to knocking combustion in spark-ignition engines. The operational differences between the standard RON rating and modern engine operation are explored in a three-part publication series. The previous study focused on the effects of lambda and knock characterization. This second study primarily focuses on the effects of spark timing on RON determination. Following the findings from the first publication, the knock intensity was captured by the knockmeter and by the maximum amplitude of pressure oscillations (MAPO) at the lambda of peak knock intensity and stoichiometry. Knock-limited spark advance tests were conducted for a set of seven Fuels for Advanced Combustion Engines (FACE) from the Coordinating Research Council (CRC) with varying chemical composition, PRFs, and Toluene Standardization Fuels (TSFs). For retarded spark timings, pre-spark low-temperature heat release was found for low RON PRFs. Low RON PRFs also showed knocking characteristics before reaching the center of combustion suggesting that the use of knock-limited spark advance (KLSA) was preferred over the knock-limited combustion phasing. Primarily paraffinic fuels tended towards increased pressure oscillations while dominantly aromatic fuels experienced higher pressure rise rates. A MAPO-based KLSA correlated best to Octane Index at a negative K-factor suggesting beyond RON operation despite being at otherwise RON conditions. At stoichiometry, the MAPO-based KLSA did neither correlate to RON nor Octane Index. Finally, good agreement was found between KLSA-based effective RON from this study to the MAPO-based effective RON from the first study.

10 SYNTHETIC FUELS↗
DOE OSTI2024

Pressure-stabilized fixed-stress iterative solutions of compositional poromechanics

We consider the numerical behavior of the fixed-stress splitting method for coupled poromechanics as undrained regimes are approached. We explain that pressure stability is related to the splitting error of the scheme, not the fact that the discrete saddle point matrix never appears in the fixed-stress approach. This observation reconciles previous results regarding the pressure stability of the splitting method. Using examples of compositional poromechanics with application to geological CO sequestration, we see that solutions obtained using the fixed-stress scheme with a low order finite element-finite volume discretization which is not inherently inf-sup stable can exhibit the same pressure oscillations obtained with the corresponding fully implicit scheme. Moreover, pressure jump stabilization can effectively remove these spurious oscillations in the fixed-stress setting, while also improving the efficiency of the scheme in terms of the number of iterations required at every time step to reach convergence.

42 ENGINEERING↗
DOE OSTI2022

Development and Characterization of a Self-Tightening Tourniquet System

Uncontrolled hemorrhage remains a leading cause of death in both emergency and military medicine. Tourniquets are essential to stopping hemorrhage in these scenarios, but they suffer from subjective, inconsistent application. Here, we demonstrate how tourniquet application can be automated using sensors and computer algorithms. The auto-tourniquet self-tightens until blood pressure oscillations are no longer registered by the pressure sensor connected to the pneumatic pressure cuff. The auto-tourniquet’s performance in stopping the bleed was comparable to manual tourniquet application, but the time required to fully occlude the bleed was longer. Application of the tourniquet was significantly smoother, and less variable, for the automatic tourniquet compared to manual tourniquet application. This proof-of-concept study highlights how automated tourniquets can be integrated with sensors to provide a much more consistent application and use compared to manual application, even in controlled, low stress testing conditions. Future work will investigate different sensors and tourniquets to improve the application time and repeatability.

Vega, Saul J.↗
DOE OSTI2025

Effects of Critical Compression Ratio on Rating Gasoline Knock Propensity

It is common practice in the automotive industry to explore the knock limits of fuels on an engine by a comparison of the knock limited spark advance (KLSA) at threshold knock intensity. However, the knock propensity of gasolines can be rated by changing one of three metrics on a variable compression ratio Cooperative Fuels Research (CFR) octane rating engine while holding the other two variables constant: knock intensity, spark timing, and critical compression ratio. The operational differences between the standard research octane number (RON) rating and modern engine operation have been explored in three parts. The first part focused on the effects of lambda and knock characterization. The second part studied the effects of spark timing. This third part explores the knock ratings of several gasolines by comparing the critical compression ratios at constant combustion phasing and knock intensity. The threshold knock intensity was based on the standard octane rating D1 pickup or by maximum amplitude of pressure oscillations (MAPO) measured by a piezoelectric cylinder pressure transducer. Several Fuels for Advanced Combustion Engines (FACE) gasolines, primary reference fuels (PRFs), and toluene standardization fuels (TSFs) were tested on a CFR octane rating engine with advanced data acquisition equipment and a piezoelectric cylinder pressure transducer. These tests deviated from the ASTM D2699 standard octane rating procedure. For each test fuel, the CFR engine was operated at stoichiometry at a constant combustion phasing (CA50) and the compression ratio was modified until a threshold knock intensity was realized. It was found that the chemical composition of the fuels affected the relationship of critical compression ratios between the D1 knockmeter and piezoelectric pressure transducer knock intensity thresholds, as well as the measured combustion maximum pressure rise rate and spark timing setting for constant CA50. For highly aromatic fuels tested at a constant MAPO knock intensity threshold, it was found that the maximum pressure rise rate was two to three times higher than that of highly paraffinic fuels with similar RON and the spark advance was several crank angle degrees less for constant combustion phasing.

Kolodziej, Christopher P↗
DOE OSTI2022

Thermoacoustic Soret separation

In a fluid mixture in a channel with an axial time-averaged temperature gradient, high-amplitude oscillating flow can greatly increase the axial flux of thermal diffusion (Soret) separation of the components of the mixture. The enhancement occurs when the oscillating lateral temperature gradient greatly exceeds the axial gradient, causing a large oscillating concentration that can be favorably time-phased with the oscillating flow. This process can occur even with a negligible pressure oscillation or with a negligible temperature response to pressure, as is the case in most liquid solutions. The thermal boundary condition imposed by realistic solids on thermoacoustic liquids is imperfect, adding mathematical complications that are absent for typical gases, for which the solid surface is temporally isothermal. Compared with gas mixtures, the high Lewis number in typical liquid solutions reduces the separation flux associated with the time-averaged temperature gradient, but it also reduces the remixing associated with the time-averaged mole-fraction gradient. For large enough channels, the second-law separation efficiency is only slightly reduced from that of steady liquid Soret separation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Identification of High-Frequency Transverse Acoustic Modes in Multi-Nozzle Can Combustors

Abstract High frequency thermoacoustic instabilities are problematic for lean-premixed gas turbines. Identifying which acoustic mode is being excited is important, in that it provides insight into potential mitigation measures and mechanical stress/life. However, the frequency spacing between modes becomes quite close for high frequency instabilities in a can combustor. This makes it difficult to distinguish between the modes (e.g., the first transverse mode vs. a higher order axial/mixed mode) based upon frequency calculations alone, which inevitably have uncertainties in boundary conditions, temperature profiles, and combustion response. This paper presents a methodology to simultaneously identify the acoustic mode shapes in the axial and azimuthal directions from acoustic pressure measurements. Multiple high temperature pressure transducers, located at distinct axial and azimuthal positions, are flush mounted in the combustor wall. The measured pressure oscillations from each sensor are then used to reconstruct the pressure distributions by using a least squares method in conjunction with a solution of a three dimensional wave equation. In order to validate the methodology, finite element method (FEM) calculations with estimated post-flame temperature is used to provide the candidate frequencies and corresponding mode shapes. The results demonstrate the reconstructed mode shapes and standing/spinning character of transverse waves, as well as the associated frequencies, both of which are consistent with the FEM predictions. Nodal line location was also extracted from the experimental data during the instabilities in the pressure data.

Kim, J.↗
DOE OSTI2021

Magnetostrictive alternator

A magnetostrictive alternator configured to convert pressure waves into electrical energy is provided. It should be appreciated that the magnetostrictive alternator may be combined in some embodiments with a Stirling engine to produce electrical power. The Stirling engine creates the oscillating pressure wave and the magnetostrictive alternator converts the pressure wave into electricity. In some embodiments, the magnetostrictive alternator may include aerogel material and magnetostrictive material. The aerogel material may be configured to convert a higher amplitude pressure wave into a lower amplitude pressure wave. The magnetostrictive material may be configured to generate an oscillating magnetic field when the magnetostrictive material is compressed by the lower amplitude pressure wave.

Dyson, Rodger W.↗
DOE OSTI2025

Efforts to stabilize composite localization elements

Localization finite elements seek to provide a robust framework for modeling ductile failure. They utilize the same constitutive model as the bulk material through the introduction of a length scale in a specialized deformation gradient that regularizes displacement discontinuity. Similar to many other elements, localization elements exhibit locking and associated pressure oscillations under incompressible plastic flow, which is a critical issue when attempting to model pressure-driven damage evolution. These issues can be drastically improved through what are essentially reduced integration techniques for the Jacobian and pressure, but there seem to be pressure-related instabilities that persist and are specific to localization elements. This memo summarizes recent efforts to mitigate and understand this problem, mostly for the 12-node composite wedge localization element in particular. At this point, it remains unclear whether the pressure fields within any localization element can be sufficiently stabilized in order to properly model failures that include softening or fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Determination of a most representative cycle from cylinder pressure ensembles via statistical method using distribution skewness

In internal combustion engine research, cylinder pressure measurements provide valuable information about the underlying thermodynamic and combustion processes, and are typically collected in ensembles of several 100 traces. Although in some particular fields of combustion research all traces are analyzed, in most cases only one trace is studied because analyzing all the traces is impractical due to the large number of collected samples. Instead, an ensemble-averaged pressure trace is commonly calculated and used for analysis. However, this pressure trace is highly smoothed and dynamic information is lost during the averaging process. With the average trace, pressure rise rates are lower and pressure oscillations such as the ones resulting from combustion knock are lost. In this work, a statistical method was developed to determine the “most representative cycle,” which is the cycle from the ensemble that has the pressure trace most representative of the engine operating condition. Eleven characteristic parameters are computed from each pressure trace and probabilistic distributions are obtained for each of the parameters using all the traces in the ensemble. Finally, the most representative cycle is selected by means of a cost function minimization. The benefits of this method are illustrated using experimental data from four very different engine platforms, under four different combustion modes and over a range of operating conditions.

42 ENGINEERING↗
DOE OSTI2024

Utah FORGE: Pump and Probe Test on an Intact Westerly Granite Sample

This dataset contains results from a pump and probe experiment conducted on an intact Westerly Granite sample with a diameter of 1 inch and a height of 1 3/8 inches. The experiment was performed within an aluminum triaxial pressure vessel (TEMCO) to investigate the non-linear acoustic parameters of the sample under varying axial pressures. The confining pressure was maintained at 4 MPa, while the axial pressure was incrementally increased from 1 MPa to 17 MPa before being reduced back to 1 MPa. 5 dynamic pressure oscillations of 0.5 MPa were applied over a 10 minute interval. The dataset includes pump controller data, linear variable differential transformer (LVDT) measurements, and acoustic data. The pump controller data tracks the confining and axial pressures, flow rates, and pump volumes. LVDT measurements provide detailed records of the axial displacement of the cell piston. Additionally, acoustic data captured by s-wave transducers is archived in a compressed file.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Utah FORGE: Pump and Probe Test on a Mated Fracture Westerly Granite Sample

This dataset contains results from a pump and probe experiment conducted on a mated fracture Westerly Granite sample with a diameter of 1 inch and a height of 2 7/8 inches. The experiment was performed within an aluminum triaxial pressure vessel (TEMCO) to investigate the non-linear acoustic parameters of the sample under varying axial pressures. The confining pressure was maintained at 4 MPa, while the axial pressure was incrementally reduced from 17 MPa to 1 MPa in 1 MPa steps. 5 dynamic pressure oscillations of 0.5 MPa were applied over a 10 minute interval. The dataset includes pump controller data, linear variable differential transformer (LVDT) measurements, and acoustic data. The pump controller data tracks the confining and axial pressures, flow rates, and pump volumes. LVDT measurements provide detailed records of the axial displacement of the cell piston. Additionally, acoustic data captured by s-wave transducers is archived in a compressed file.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Relating Hydro–Mechanical and Elastodynamic Properties of Dynamically Stressed Tensile–Fractured Rock in Relation to Applied Normal Stress, Fracture Aperture, and Contact Area

We exploit nonlinear elastodynamic properties of fractured rock to probe the micro-scale mechanics of fractures and understand the relation between fluid transport and fracture aperture under dynamic stressing. Experiments were conducted on rough, tensile-fractured Westerly granite subject to triaxial stresses. We measure fracture permeability for steady-state fluid flow with deionized water. Pore pressure oscillations are applied at amplitudes ranging from 0.2 to 1 MPa at 1 Hz frequency. During dynamic stressing we transmit ultrasonic signals through the fracture using an array of piezoelectric transducers (PZTs) to monitor evolution of interface properties. We examine the influence of fracture aperture and contact area by conducting measurements at effective normal stresses of 10–20 MPa. Additionally, the evolution of contact area with stress is characterized using pressure sensitive film. These experiments are conducted separately with the same fracture and map contact area at stresses from 9 to 21 MPa. The measurements are a proxy for “true” contact area for the fracture surface and we relate them to elastic properties using the calculated PZT sensor footprints via numerical modeling of Fresnel zones. We compare the elastodynamic response of the fracture using the stress-induced changes in ultrasonic wave velocities for transmitter-receiver pairs to image spatial variations in contact properties. We show that nonlinear elasticity and permeability enhancement decrease with increasing normal stress. Additionally, post-oscillation wave velocity and permeability exhibit quick recoveries toward pre-oscillation values. Estimates of fracture contact area (global and local) demonstrate that the elastodynamic and permeability responses are dominated by fracture topology.

58 GEOSCIENCES↗
DOE OSTI2021

A Transported Livengood–Wu Integral Model for Knock Prediction in Computational Fluid Dynamics Simulation

This work describes the development of a transported Livengood–Wu (L–W) integral model for computational fluid dynamics (CFD) simulation to predict autoignition and engine knock tendency. The currently employed L–W integral model considers both single-stage and two-stage ignition processes, thus can be generally applied to different fuels such as paraffin, olefin, aromatics, and alcohol. The model implementation is first validated in simulations of homogeneous charge compression ignition (HCCI) combustion for three different fuels, showing good accuracy in prediction of autoignition timing for fuels with either single-stage or two-stage ignition characteristics. Then, the L–W integral model is coupled with G-equation model to indicate end-gas autoignition and knock tendency in CFD simulations of a direct-injection spark-ignition engine. This modeling approach is about 10 times more efficient than the ones that based on detailed chemistry calculation and pressure oscillation analysis. Two fuels with same Research Octane Number (RON) but different octane sensitivity are studied, namely, Co-Optima alkylate and Co-Optima E30. Feed-forward neural network model in conjunction with multivariable minimization technique is used to generate fuel surrogates with targets of matched RON, octane sensitivity, and ethanol content. The CFD model is validated against experimental data in terms of pressure traces and heat release rate for both fuels under a wide range of operating conditions. The knock tendency—indicated by the fuel energy contained in the autoignited region—of the two fuels at different load conditions correlates well with the experimental results and the fuel octane sensitivity, implying the current knock modeling approach can capture the octane sensitivity effect and can be applied to further investigation on composition of octane sensitivity.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

A transported Livengood-Wu integral model for knock prediction in CFD simulation

This work describes the development of a transported Livengood-Wu (L-W) integral model for computational fluid dynamics (CFD) simulation to predict auto-ignition and engine knock tendency. The currently employed L-W integral model considers both single-stage and two-stage ignition processes, thus can be generally applied to different fuels such as paraffin, olefin, aromatics and alcohol. The model implementation is first validated in simulations of homogeneous charge compression ignition combustion for three different fuels, showing good accuracy in prediction of auto-ignition timing for fuels with either single-stage or two-stage ignition characteristics. Then, the L-W integral model is coupled with G-equation model to indicate end-gas auto-ignition and knock tendency in CFD simulations of a direct injection spark ignition engine. This modeling approach is about 10 times more efficient than the ones that based on detailed chemistry calculation and pressure oscillation analysis. Two fuels with same Research Octane Number (RON) but different octane sensitivity are studied, namely Co-Optima Alkylate and Co-Optima E30. Feed-forward neural network model in conjunction with multi-variable minimization technique is used to generate fuel surrogates with targets of matched RON, octane sensitivity and ethanol content. The CFD model is validated against experimental data in terms of pressure traces and heat release rate for both fuels under a wide range of operating conditions. The knock tendency indicated by the fuel energy contained in the auto-ignited region of the two fuels at different load conditions correlates well with the experimental results and the fuel octane sensitivity, implying the current knock modeling approach can capture the octane sensitivity effect and can be applied to further investigation on composition of octane sensitivity.

Yue, Zongyu↗