Search NASA⌕ Search

SEARCH · Search NASA

Results for “pyroshock”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Controlled Pyroshock Test Transients Can Be Used To Better Match Operational Shock Transients and Reduce Artificial Pyroshock Test Failures [Slides]

Shock analysis is typically done via SRS (shock response spectrum). Oftentimes shock analysis is not performed because most loads specifications only supply SRS requirements with no representative shock transients that can be used for analysis. SRS analysis is too conservative. There is no structural dynamics involved as all modes are assumed to have peak responses simultaneously and in-phase with each other. It is possible that all other loads and combination of loads show the design to be good, whereas SRS analysis (1000 g’s are involved) results may require redesign. Multiple shock transients can satisfy a SRS, yet most loads documents don’t provide a representative shock transient that could be used for shock analysis. Shock testing is less common than harmonic and random vibration testing. Engineers typically go into shock tests with very little knowledge of what to expect. A pass/fail type of approach with very little engineering done to prepare for the test or to control the type of shock transient is used. Most engineers will not model the shock test fixture due to lack of knowledge about the details of the test setup. Shock analysis and testing is often an open loop type situation with no test setup modeling, no test correlation, and no control over the test shock transient. In this work, if we can create applied test force transient that comes close to matching calculated force transient then a more reasonable acceleration transient will be created at the test reference accelerometer that better matches operational shocks.

42 ENGINEERING↗

Development of an FPGA-based multipoint laser pyroshock measurement system for explosive bolts

Pyroshock can cause failure to the objective of an aerospace structure by damaging its sensitive electronic equipment, which is responsible for performing decisive operations. A pyroshock is the high intensity shock wave that is generated when a pyrotechnic device is explosively triggered to separate, release, or activate structural subsystems of an aerospace architecture. Pyroshock measurement plays an important role in experimental simulations to understand the characteristics of pyroshock on the host structure. This paper presents a technology to measure a pyroshock wave at multiple points using laser Doppler vibrometers (LDVs). These LDVs detect the pyroshock wave generated due to an explosive-based pyrotechnical event. Field programmable gate array (FPGA) based data acquisition is used in the study to acquire pyroshock signals simultaneously from multiple channels. This paper describes the complete system design for multipoint pyroshock measurement. The firmware architecture for the implementation of multichannel data acquisition on an FPGA-based development board is also discussed. An experiment using explosive bolts was configured to test the reliability of the system. Pyroshock was generated using explosive excitation on a 22-mm-thick steel plate. Three LDVs were deployed to capture the pyroshock wave at different points. The pyroshocks captured were displayed as acceleration plots. The results showed that our system effectively captured the pyroshock wave with a peak-to-peak magnitude of 303 741 g. The contribution of this paper is a specialized architecture of firmware design programmed in FPGA for data acquisition of large amount of multichannel pyroshock data. The advantages of the developed system are the near-field, multipoint, non-contact, and remote measurement of a pyroshock wave, which is dangerous and expensive to produce in aerospace pyrotechnic tests.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Introduction to the Demonstration of Pyroshock Response Prediction Methods Using NASA ShockSat Data Virtual Collection

Mechanical shocks, particularly pyroshocks, are environments that all spacecraft and launch vehicles experience. Pyroshocks can be challenging design environments for space hardware because these events are often high frequency, high intensity transients. Furthermore, since design decisions must be made relatively early in the design phase, understanding, and accurately defining pyroshock excitation and the loads that it imparts on components is important to ensure the high reliability required of spacecraft and rockets. Here, general guidelines about shock transmission through spacecraft structures are provided in NASA and MIL handbooks and standards, but these are relatively broad guidelines, and recent studies have shown that more accurate and less-conservative predictions are needed. However, predicting shock response accurately is still a challenge because of the high frequencies in a pyroshock excitation.

Babuska, Vit [Sandia National Laboratories (SNL-NM↗

Controlled Pyroshock Transients Can Be Used To Better Match Operational Shock Transients and Improve Shock Analysis and Testing

SRS analysis and testing to SRS is known to be conservative since SRS is generated from maxi-max shock transient data, maximum peaks are assumed to occur for each mode simultaneously, and the structural dynamics are not accounted for between the shock source and the test article. Knowing the structural dynamics of a shock test setup it is possible to subscribe a force shock transient applied at a particular strike location and direction to achieve a desired shock transient at a test reference accelerometer. The SRS at this test accelerometer reference location can be used to compare to the reference SRS, but the key reference is the shock transient not the SRS, which should lead to more realistic shock testing that better matches operational shock transient data and reduces artificial test failures that don’t occur in operational usage. The desired test shock transient should match operational shock transients. As such, the test shock transient should look similar to the operational shock transient and have similar positive and negative peaks, the same shape, and the same duration. Many shock transients can be created that satisfy an SRS, but better control of these shock transient parameters is needed to better match operational shock transients so that more realistic and less conservative shock testing can be performed. Three different shock transients are presented that satisfy a given SRS and the results are compared for an electronic board (test article) attached to a circular shock resonance test plate.

SRS, shock transient, frequency domain, FRF↗