SEARCH · Search NASA
Results for “quantum dots nanotubes”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Fine structure of current noise spectra in nanoelectromechanical resonators
Here, we study the frequency-dependent noise of a suspended carbon nanotube quantum dot nanoelectromechanical resonator induced by electron-vibration coupling. Using a rigorous Keldysh diagrammatic technique, we establish a formal framework connecting the vibrational properties to electrical measurements. We find that the noise power spectrum exhibits a narrow resonant peak at the frequency of the vibrational modes. However, this fine structure tends to disappear due to a coherent cancellation effect when the tunneling barriers are tuned to a symmetric point. Notably, measuring the electrical current noise spectra provides a sensitive alternative method for detecting the damping and dephasing of quantum vibrational modes.
Synthetic Pathways to gamma-Graphyne and Related Allotropes of Carbon
Graphynes, two-dimensional carbon lattices combining sp 1 and sp 2 hybridized atoms, were predicted theoretically more than three decades ago, but few structures have been realized to date. These carbons are believed to possess remarkable mechanical and electronic properties, including high charge carrier mobilities comparable to those in graphene (10 4 to 10 5 cm 2 V -1 s -1 ). Unlike graphene, certain graphynes are predicted to be intrinsic semiconductors. Among these intriguing structures, γ-graphyne stands out as the structurally simplest and most symmetric sp 1 /sp 2 lattice. γ-Graphyne was first theorized in 1987. In contrast with graphene, γ-graphyne will be a semiconductor with a small band gap suitable for fabrication of electronic devices. This solves one of the fundamental problems of carbon-based electronics, the necessity for inducing a band gap in graphene. γ-Graphyne has the potential to form the basis for the next generation of carbon-based electronics operating at speeds unattainable by traditional silicon chips. Unlike silicon, γ-graphyne is a direct band gap semiconductor, and it will feature exceptional strength comparable to that of other 2D carbon allotropes. Such combination of properties may enable a new generation of highly efficient, ultra-light and flexible solar cells. Despite being a potentially “magical” material, γ-graphyne remained synthetically elusive for over three decades. The primary goals of this project were: (1) Synthesis of bulk γ-graphyne phases through solution-phase 2D polymerizations; (2) Experimental exploration of the physical and chemical properties of γ-graphyne; and (3) Mechanistic and theoretical studies of the novel chemical transformations developed in Goal 1. Common pyrolytic and vapor-deposition methodologies used for the synthesis of graphitic allotropes are unsuitable for graphyne and other sp 1 -contaning structures, as acetylenes readily convert to graphene and amorphous carbon at high temperatures. In contrast, this proposal is based on solution-based 2D polymerization. The major advantages of this approach over the traditional high temperature techniques are the potential to adjust the structure of the material with atomic precision, and the possibility of using structurally complex and relatively fragile repeat units. The outcomes of this research can revolutionize carbon nanotechnology, expanding the field’s structural toolbox beyond primarily graphitic and benzenoid structures. Understanding the chemistry of sp 1 carbon allotropes can lead to entirely new classes of structures with unique properties, including graphyne ribbons, nanotubes, quantum dots, and heterostructures with other 2D materials. Furthermore, the development of reliable and robust synthetic pathways towards periodic covalent molecular sheets with atomically precise structures shall have a profound impact on chemistry and materials science.
Solar Powered CO.Sub.2 Conversion
Methods and devices for reducing CO.sub.2 to produce hydrocarbons are disclosed. A device comprises a photoanode capable of splitting H.sub.2O into electrons, protons, and oxygen; an electrochemical cell cathode comprising an electro-catalyst capable of reducing CO.sub.2; H.sub.2O in contact with the surface of the photoanode; CO.sub.2 in contact with the surface of the cathode; and a proton-conducting medium positioned between the photoanode and the cathode. Electrical charges associated with the protons and the electrons move from the photoanode to the cathode, driven in part by a chemical potential difference sufficient to drive the electrochemical reduction of CO.sub.2 at the cathode. A light beam is the sole source of energy used to drive chemical reactions. The photoanode can comprise TiO.sub.2 nanowires or nanotubes, and can also include WO.sub.3 nanowires or nanotubes, quantum dots of CdS or PbS, and Ag or Au nanostructures. The cathode can comprise a conductive gas diffusion layer with nanostructures of an electro-catalyst such as Cu or Co.
Quantum dot modeling using NEMO 3-D
Explore the source record for details and available documents.
Nanostructured Materials Developed for Solar Cells
There has been considerable investigation recently regarding the potential for the use of nanomaterials and nanostructures to increase the efficiency of photovoltaic devices. Efforts at the NASA Glenn Research Center have involved the development and use of quantum dots and carbon nanotubes to enhance inorganic and organic cell efficiencies. Theoretical results have shown that a photovoltaic device with a single intermediate band of states resulting from the introduction of quantum dots offers a potential efficiency of 63.2 percent. A recent publication extended the intermediate band theory to two intermediate bands and calculated a limiting efficiency of 71.7 percent. The enhanced efficiency results from converting photons of energy less than the band gap of the cell by an intermediate band. The intermediate band provides a mechanism for low-energy photons to excite carriers across the energy gap by a two-step process.
Nanotube Sensors
Under this project, we explored the feasibility of utilizing carbon nanotubes in sensing applications. The grant primarily supported a graduate student, who worked on a number of aspects of the electrical properties of carbon nanotubes in collaboration with other researchers in my group. The two major research accomplishments are described below. The first accomplishment is the demonstration that solution carbon nanotube transistors functioned well in an electrolyte environment. This was important for two reasons. First, it allowed us to explore the ultimate limits of nanotube electronic performance by using the electrolyte as a highly effective gate, with a dielectric constant of approximately 80 and an effective insulator thickness of approximately 1 nm. Second, it showed that nanotubes function well under biologically relevant conditions (salty water) and therefore offer great promise as biological sensors. The second accomplishment was the demonstration that a voltage pulse applied to an AFM tip could be used to electrically cut carbon nanotubes. We also showed that a carefully applied pulse could also 'nick' a nanotube, creating a tunnel barrier without completely breaking the tube. Nicking was employed to make, for example, a quantum dot within a nanotube.
Low-dimensional solid-state single-photon emitters
Solid-state single-photon emitters (SPEs) are attracting significant attention as fundamental components in quantum computing, communication, and sensing. Low-dimensional materials-based SPEs (LD-SPEs) have drawn particular interest due to their high photon extraction efficiency, ease of integration with photonic circuits, and strong coupling with external fields. The accessible surfaces of LD materials allow for deterministic control over quantum light emission, while enhanced quantum confinement and light–matter interactions improve photon emissive properties. This perspective examines recent progress in LD-SPEs across four key materials: zero-dimensional (0D) semiconductor quantum dots, one-dimensional (1D) nanotubes, two-dimensional (2D) materials, including hexagonal boron nitride (hBN) and transition metal dichalcogenides (TMDCs). We explore their structural and photophysical properties, along with techniques such as spectral tuning and cavity coupling, which enhance SPE performance. Finally, we address future challenges and suggest strategies for optimizing LD-SPEs for practical quantum applications.
Spectral Performance of Multilayer Amorphous Selenium and Selenium–Tellurium Photodetectors
The ability to robustly and with scalability detect single photons in the visible spectrum with wavelength resolution would transform many imaging applications. Theoretical studies propose an array of carbon nanotubes (CNTs) functionalized with semiconductor quantum dots (QDs) as a physical realization of such photon sensors. In this work, we report approaches to synthesize these CNT-QD nanostructures using DNA as a smart glue to connect CNTs to QDs.
Nanostructured Materials Development for Space Power
There have been many recent advances in the use of nanostructured materials for space power applications. In particular, the use of high purity single wall nanotubes holds promise for a variety of generation and storage devices including: thin film lithium ion batteries, microelectronic proton exchange membrane (PEM) fuel cells, polymeric thin film solar cells, and thermionic power supplies is presented. Semiconducting quantum dots alone and in conjunction with carbon nanotubes are also being investigated for possible use in high efficiency photovoltaic solar cells. This paper will review some of the work being done at RIT in conjunction with the NASA Glenn Research Center to utilize nanomaterials in space power devices.
Low-dimensional carbon materials decorated FAPbI 3 for carbon-based perovskite solar cells
Carbon nanomaterials are at the forefront of research in perovskite solar cells (PSCs) due to their exceptional electrical, optical, and stability properties. Their diverse applications include serving as interfacial layers, additives, hole and electron transport materials, and back electrodes. While the influence of various low-dimensional carbon nanomaterial structures on crystallinity, optical and electrical performance, and overall device efficiency has been a topic of interest, it has not been thoroughly explored until now. In this study, we effectively integrated carbon quantum dots (CQDs), multi-walled carbon nanotubes (MWCNTs), and graphene into the FAPbI 3 photoactive layer using a two-step sequential deposition method. Our experiments revealed marked improvements in the photovoltaic performance of PSCs that incorporated all three types of carbon nanomaterials. In particular, the data shows significant enhancements in power conversion efficiency, demonstrating the effectiveness of these materials in optimizing device functionality. Notably, MWCNTs distinguished themselves by exhibiting a remarkable potential for enhancing long-term stability. This finding underscores the importance of selecting the right carbon nanomaterials for future PSC developments, paving the way for more reliable and efficient solar energy solutions. As a result, our research highlights the critical role of carbon nanomaterials in advancing perovskite solar technology.
Transformational Nano-confined Ionic Liquid Membrane for Greater than or Equal to 97 Percent Carbon Dioxide Capture from Natural Gas Combined Cycle Flue Gas
A transformational process based on nano-confined ionic liquid (NCIL) membranes was developed for capturing ≥97% CO 2 from natural gas combined cycle (NCCC) flue gas. The NCIL membranes were prepared by loading amino acid ionic liquid into a framework composed of single-walled carbon nanotube mesh filled with graphene oxide quantum dots. The membranes exhibited CO 2 permeance as high as 2,000 GPU with a CO 2 /N2 selectivity of 2,300 for a typical NGCC flue gas composition. When H 2 O vapor sweep was applied in the permeate side, 96.6% CO2 dry-basis purity and 97.6% CO 2 capture rate were achieved for a simulated NGCC flue gas with single stage. In the process design, a highly H 2 O-selective membrane would be needed to recover majority of the H 2 O vapor, and the recovered H 2 O vapor could be recycled to the permeate side of the NCIL membrane. Sulfonated poly(ether ether ketone) membranes were successfully developed for this purpose. These membranes exhibited H 2 O permeance great than 11,000 GPU and H 2 O/CO 2 selectivity greater than 1,000 at 70ºC for a feed mixture consisting of 14.5 vol% H2O and balanced CO 2 . A standalone membrane model using MATLAB platform was developed for process simulation. The model was validated with experimental data. Techno-economic analysis based on the testing data collected during the current program suggests this transformational membrane process can achieve 97% CO 2 capture efficiency with a cost of $47.8/tonne of CO 2 , which is a 21% reduction versus DOE’s reference case B31B.97.
Novel Materials, Processing and Device Technologies for Space Exploration with Potential Dual-Use Applications
We highlight results of a broad spectrum of efforts on lower-temperature processing of nanomaterials, novel approaches to energy conversion, and environmentally rugged devices. Solution-processed quantum dots of copper indium chalcogenide semiconductors and multiwalled carbon nanotubes from lower-temperature spray pyrolysis are enabled by novel (precursor) chemistry. Metal-doped zinc oxide (ZnO) nanostructured components of photovoltaic cells have been grown in solution at low temperature on a conductive indium tin oxide substrate. Arrays of ZnO nanorods can be templated and decorated with various semiconductor and metallic nanoparticles. Utilizing ZnO in a more broadly defined energy conversion sense as photocatalysts, unwanted organic waste materials can potentially be repurposed. Current efforts on charge carrier dynamics in nanoscale electrode architectures used in photoelectrochemical cells for generating solar electricity and fuels are described. The objective is to develop oxide nanowire-based electrode architectures that exhibit improved charge separation, charge collection and allow for efficient light absorption. Investigation of the charge carrier transport and recombination properties of the electrodes will aid in the understanding of how nanowire architectures improve performance of electrodes for dye-sensitized solar cells. Nanomaterials can be incorporated in a number of advanced higher-performance (i.e. mass specific power) photovoltaic arrays. Advanced technologies for the deposition of 4H-silicon carbide are described. The use of novel precursors, advanced processing, and process studies, including modeling are discussed from the perspective of enhancing the performance of this promising material for enabling technologies such as solar electric propulsion. Potential impact(s) of these technologies for a variety of aerospace applications are highlighted throughout. Finally, examples are given of technologies with potential spin-offs for dual-use or terrestrial applications.
Novel Materials, Processing, and Device Technologies for Space Exploration with Potential Dual-Use Applications
We highlight results of a broad spectrum of efforts on lower-temperature processing of nanomaterials, novel approaches to energy conversion, and environmentally rugged devices. Solution-processed quantum dots of copper indium chalcogenide semiconductors and multi-walled carbon nanotubes from lower-temperature spray pyrolysis are enabled by novel (precursor) chemistry. Metal-doped zinc oxide (ZnO) nanostructured components of photovoltaic cells have been grown in solution at low temperature on a conductive indium tin oxide substrate. Arrays of ZnO nanorods can be templated and decorated with various semiconductor and metallic nanoparticles. Utilizing ZnO in a more broadly defined energy conversion sense as photocatalysts, unwanted organic waste materials can potentially be re-purposed. Current efforts on charge carrier dynamics in nanoscale electrode architectures used in photoelectrochemical cells for generating solar electricity and fuels are described. The objective is to develop oxide nanowire-based electrode architectures that exhibit improved charge separation, charge collection and allow for efficient light absorption. Investigation of the charge carrier transport and recombination properties of the electrodes will aid in the understanding of how nanowire architectures improve performance of electrodes for dye-sensitized solar cells. Nanomaterials can be incorporated in a number of advanced higher-performance (i.e. mass specific power) photovoltaic arrays. Advanced technologies for the deposition of 4H-silicon carbide are described. The use of novel precursors, advanced processing, and process studies, including modeling are discussed from the perspective of enhancing the performance of this promising material for enabling technologies such as solar electric propulsion. Potential impact(s) of these technologies for a variety of aerospace applications are highlighted throughout. Finally, examples are given of technologies with potential spin-offs for dual-use or terrestrial applications.
Nanostructured Materials for Solar Cells
The use of both inorganic and organic nanostructured materials in producing high efficiency photovoltaics is discussed in this paper. Recent theoretical results indicate that dramatic improvements in device efficiency may be attainable through the use of semiconductor quantum dots in an ordinary p-i-n solar cell. In addition, it has also recently been demonstrated that quantum dots can also be used to improve conversion efficiencies in polymeric thin film solar cells. A similar improvement in these types of cells has also been observed by employing single wall carbon nanotubes. This relatively new carbon allotrope may assist both in the disassociation of excitons as well as carrier transport through the composite material. This paper reviews the efforts that are currently underway to produce and characterize these nanoscale materials and to exploit their unique properties.
Physics of Quantum Structures in Photovoltaic Devices
There has been considerable activity recently regarding the possibilities of using various nanostructures and nanomaterials to improve photovoltaic conversion of solar energy. Recent theoretical results indicate that dramatic improvements in device efficiency may be attainable through the use of three-dimensional arrays of zero-dimensional conductors (i.e., quantum dots) in an ordinary p-i-n solar cell structure. Quantum dots and other nanostructured materials may also prove to have some benefits in terms of temperature coefficients and radiation degradation associated with space solar cells. Two-dimensional semiconductor superlattices have already demonstrated some advantages in this regard. It has also recently been demonstrated that semiconducting quantum dots can also be used to improve conversion efficiencies in polymeric thin film solar cells. Improvement in thin film cells utilizing conjugated polymers has also be achieved through the use of one-dimensional quantum structures such as carbon nanotubes. It is believed that carbon nanotubes may contribute to both the disassociation as well as the carrier transport in the conjugated polymers used in certain thin film photovoltaic cells. In this paper we will review the underlying physics governing some of the new photovoltaic nanostructures being pursued, as well as the the current methods being employed to produce III-V, II-VI, and even chalcopyrite-based nanomaterials and nanostructures for solar cells.
NASA Tech Briefs, July 2004
Topics: Optoelectronic Sensor System for Guidance in Docking; Hybrid Piezoelectric/Fiber-Optic Sensor Sheets; Multisensor Arrays for Greater Reliability and Accuracy; Integrated-Optic Oxygen Sensors; Ka-Band Autonomous Formation Flying Sensor; CMOS VLSI Active-Pixel Sensor for Tracking; Lightweight, Self-Deploying Foam Antenna Structures; Electrically Small Microstrip Quarter-Wave Monopole Antennas; A 2-to-28-MHz Phase-Locked Loop; Portable Electromyograph; Open-Source Software for Modeling of Nanoelectronic Devices; Software for Generating Strip Maps from SAR Data; Calibration Software for use with Jurassicprok; Software for Probabilistic Risk Reduction; Software Processes SAR Motion-Measurement Data; Improved Method of Purifying Carbon Nanotubes; Patterned Growth of Carbon Nanotubes or Nanofibers; Lightweight, Rack-Mountable Composite Cold Plate/Shelves; SiC-Based Miniature High-Temperature Cantilever Anemometer; Inlet Housing for a Partial-Admission Turbine; Lightweight Thermoformed Structural Components and Optics; Growing High-Quality InAs Quantum Dots for Infrared Lasers; Selected Papers on Protoplanetary Disks; Module for Oxygenating Water without Generating Bubbles; Coastal Research Imaging Spectrometer; Rapid Switching and Modulation by use of Coupled VCSELs; Laser-Induced-Fluorescence Photogrammetry and Videogrammetry; Laboratory Apparatus Generates Dual-Species Cold Atomic Beam; Laser Ablation of Materials for Propulsion of Spacecraft; Small Active Radiation Monitor; Hybrid Image-Plane/Stereo Manipulation; Partitioning a Gridded Rectangle into Smaller Rectangles; Digital Radar-Signal Processors Implemented in FPGAs; Part 1 of a Computational Study of a Drop-Laden Mixing Layer; and Some Improvements in Signal-Conditioning Circuits.
NASA Tech Briefs, October 2003
Topics covered include: Cryogenic Temperature-Gradient Foam/Substrate Tensile Tester; Flight Test of an Intelligent Flight-Control System; Slat Heater Boxes for Thermal Vacuum Testing; System for Testing Thermal Insulation of Pipes; Electrical-Impedance-Based Ice-Thickness Gauges; Simulation System for Training in Laparoscopic Surgery; Flasher Powered by Photovoltaic Cells and Ultracapacitors; Improved Autoassociative Neural Networks; Toroidal-Core Microinductors Biased by Permanent Magnets; Using Correlated Photons to Suppress Background Noise; Atmospheric-Fade-Tolerant Tracking and Pointing in Wireless Optical Communication; Curved Focal-Plane Arrays Using Back-Illuminated High-Purity Photodetectors; Software for Displaying Data from Planetary Rovers; Software for Refining or Coarsening Computational Grids; Software for Diagnosis of Multiple Coordinated Spacecraft; Software Helps Retrieve Information Relevant to the User; Software for Simulating a Complex Robot; Software for Planning Scientific Activities on Mars; Software for Training in Pre-College Mathematics; Switching and Rectification in Carbon-Nanotube Junctions; Scandia-and-Yttria-Stabilized Zirconia for Thermal Barriers; Environmentally Safer, Less Toxic Fire-Extinguishing Agents; Multiaxial Temperature- and Time-Dependent Failure Model; Cloverleaf Vibratory Microgyroscope with Integrated Post; Single-Vector Calibration of Wind-Tunnel Force Balances; Microgyroscope with Vibrating Post as Rotation Transducer; Continuous Tuning and Calibration of Vibratory Gyroscopes; Compact, Pneumatically Actuated Filter Shuttle; Improved Bearingless Switched-Reluctance Motor; Fluorescent Quantum Dots for Biological Labeling; Growing Three-Dimensional Corneal Tissue in a Bioreactor; Scanning Tunneling Optical Resonance Microscopy; The Micro-Arcsecond Metrology Testbed; Detecting Moving Targets by Use of Soliton Resonances; and Finite-Element Methods for Real-Time Simulation of Surgery.