SEARCH · Search NASA

Results for “radio attenuation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

DOE OSTI2022

60 GHz Outdoor Propagation Measurements and Analysis Using Facebook Terragraph Radios

The high attenuation of millimeter-wave (mmWave) would significantly reduce the coverage areas, and hence it is critical to study the propagation characteristics of mmWave in multiple deployment scenarios. In this work, we investigated the propagation and scattering behavior of 60 GHz mmWave signals in outdoor environments at a travel distance of 98 m for an aerial link (rooftop to rooftop), and 147 m for a ground link (light-pole to light-pole). Measurements were carried out using Facebook Terragraph (TG) radios. Results include received power, path loss, signal-to-noise ratio (SNR), and root mean square (RMS) delay spread for all beamforming directions supported by the antenna array. Strong line-of-sight (LOS) propagation exists in both links. We also observed rich multipath components (MPCs) due to edge scatterings in the aerial link, while only LOS and ground reflection MPCs in the other link.

60 GHz↗

DOE OSTI2022

A Wireless Underground Sensor Network Field Pilot for Agriculture and Ecology: Soil Moisture Mapping Using Signal Attenuation

Wireless Underground Sensor Networks (WUSNs) that collect geospatial in situ sensor data are a backbone of internet-of-things (IoT) applications for agriculture and terrestrial ecology. In this paper, we first show how WUSNs can operate reliably under field conditions year-round and at the same time be used for determining and mapping soil conditions from the buried sensor nodes. We demonstrate the design and deployment of a 23-node WUSN installed at an agricultural field site that covers an area with a 530 m radius. The WUSN has continuously operated since September 2019, enabling real-time monitoring of soil volumetric water content (VWC), soil temperature (ST), and soil electrical conductivity. Secondly, we present data collected over a nine-month period across three seasons. We evaluate the performance of a deep learning algorithm in predicting soil VWC using various combinations of the received signal strength (RSSI) from each buried wireless node, above-ground pathloss, the distance between wireless node and receive antenna (D), ST, air temperature (AT), relative humidity (RH), and precipitation as input parameters to the model. The AT, RH, and precipitation were obtained from a nearby weather station. We find that a model with RSSI, D, AT, ST, and RH as inputs was able to predict soil VWC with an R 2 of 0.82 for test datasets, with a Root Mean Square Error of ±0.012 (m 3 /m 3 ). Hence, a combination of deep learning and other easily available soil and climatic parameters can be a viable candidate for replacing expensive soil VWC sensors in WUSNs.

47 OTHER INSTRUMENTATION↗

DOE OSTI2023

Generalized Theory and Realization of Continuously Loss-Programmable Bandpass Filtering Attenuators

With the increased demand for modern wireless systems in various applications, the need for adjustable radio frequency (RF) systems has dramatically increased. These modern systems rely on operating in the microwave frequency spectrum (1 GHz to 1 THz) without interference from other devices while also retaining the ability to detect very low and very high power signals simultaneously. There is also an ever-increasing demand for reducing the cost, size, weight, and power (C-SWaP) of these modern RF systems, driving the demand for more agile filters in the microwave frequency spectrum. In this paper, a generalized theory of bandpass filtering attenuators (filtenuators) is proposed. A filtenuator is a device that combines the frequency- selective characteristics of a filter and the loss-programmable characteristics of an attenuator into a single component. The loss- programmable aspect of the filtenuator is based on the tuning of a π-network of resistances, which are implemented using PIN diodes to control the individual resistance values electronically. A loss-programmable, third-order Chebyshev bandpass filtenuator is designed, fabricated, and measured to verify the generalized theory. The filtenuator is designed to operate at 1 GHz and have a tunable attenuation range of 2-10 dB. This proposed filtenuator demonstrates the feasibility of a tunable, low C-SWaP solution to increase RF system dynamic range and a design process that allows for future development of filtenuators.

42 ENGINEERING↗

DOE OSTI2022

Design of a 3rd Order Lumped-Element Filtering Attenuator

This paper presents a novel filtering attenuator (filtenuator) concept, which allows for adjustable passband attenuation and filtering characteristics in a single design. The mathematical equations relating the desired passband loss to required resistance values are provided and validated with ideal circuit simulations. A third-order Chebyshev static filtenuator is designed at 1 GHz with multiple values of attenuation using lumped-element components as a proof of concept. Simulated and measured results for a 3 dB filtenuator show good agreement and several attenuation levels are shown to validate the concept. The proposed static filtenuator has advantages of ease of modification, compact size, and low cost, which are necessities in meeting the needs of reducing size, weight, power, and cost (SWaP-C) in future radio frequency transceivers.

Filter, Attenuator, Band-pass Filter (BPF), Lumped↗

DOE OSTI2021

Imaging 192/193m Ir sources using digital autoradiography for nuclear forensic applications [Slides]

This work aims to develop a new methodology for assaying 192/193m Ir-containing materials. SDDs cannot determine activity spatially, thus it is important that the prepared samples are uniformly distributed. Autoradiography is used to image radioactive samples using imaging media by direct exposure. Using this technique, radio-iridium samples will be imaged to determine uniformity and self-attenuation as a function of mass.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2022

Hunting extreme BL Lacertae blazars with Fermi-Large Area Telescope

ABSTRACT The emission of very-high-energy (VHE) photons ($E\ \gt\ 100\ \mathrm{GeV}$) in blazars is closely connected to the production of ultra-relativistic particles and the role of these γ-ray sources as cosmic particle accelerators. This work focuses on a selection of 22 γ-ray objects from the 2BIGB catalogue of high-synchrotron-peaked sources, which are classified as blazar candidates of uncertain type in the 4FGL-DR2 catalogue. We study these sources by means of a re-analysis of the first 10 yr of γ-ray data taken with the Fermi-Large Area Telescope, including the attenuation by the extragalactic background light. Their broad-band spectral energy distributions are also evaluated, using multiwavelength archival data in the radio, optical, and X-ray bands, in terms of one-zone synchrotron-self-Compton models, adding an external Compton component when needed. Out of this analysis, we identify 17 new extreme high-synchrotron-peaked (EHSP) candidates and compare their physical parameters with those of prototypical EHSP blazars. Finally, the resulting models are used to assess their detectability by the present and future generation of ground-based Imaging Atmospheric Cherenkov Telescopes. We find two VHE candidates within the reach of the current and next generation of Cherenkov telescopes: J0847.0−2336 and J1714.0−2029.

Nievas Rosillo, M. (ORCID:0000000283219168)↗

DOE OSTI2020

Probing the angular and polarization reconstruction of the ARIANNA detector at the South Pole

The sources of ultra-high energy (UHE) cosmic rays, which can have energies up to 10 20 eV, remain a mystery. UHE neutrinos may provide important clues to understanding the nature of cosmic-ray sources. ARIANNA aims to detect UHE neutrinos via radio (Askaryan) emission from particle showers when a neutrino interacts with ice, which is an efficient method for neutrinos with energies between 10 16 eV and 10 20 eV. The ARIANNA radio detectors are located in Antarctic ice just beneath the surface. Neutrino observation requires that radio pulses propagate to the antennas at the surface with minimum distortion by the ice and firn medium. Using the residual hole from the South Pole Ice Core Project, radio pulses were emitted from a transmitter located up to 1.7 km below the snow surface. By measuring these signals with an ARIANNA surface station, the angular and polarization reconstruction abilities are quantified, which are required to measure the direction of the neutrino. After deconvolving the raw signals for the detector response and attenuation from propagation through the ice, the signal pulses show no significant distortion and agree with a reference measurement of the emitter made in an anechoic chamber. Furthermore, the signal pulses reveal no significant birefringence for our tested geometry of mostly vertical ice propagation. The origin of the transmitted radio pulse was measured with an angular resolution of 0.37° indicating that the neutrino direction can be determined with good precision if the polarization of the radio-pulse can be well determined. In this work, we obtained a resolution of the polarization vector of 2.7°. Neither measurement show a significant offset relative to expectation.

47 OTHER INSTRUMENTATION↗

DOE OSTI2025

Meter-scale High-temperature Superconducting RF Waveguides with Integrated Filters and Attenuators

Here, we report the performance of coplanar, multifilament waveguides manufactured from crystalline films of a well-known HTS compound, YBCO, transferred to a low-loss dielectric substrate, such as E-Kapton. The coplanar two-line waveguide delivers low cross-talk, below 20 dB level, and low attenuation, below 4 dB/m at 6 GHz, 77 K. Controlled-impedance 50 Ω waveguides would require a method for reliable patterning narrow, less than 100-micron wide, YBCO traces over a meter length. We report a lithography-etching approach that minimizes the difference in the etching rate of YBCO and the metallization layers of Ag and Cu. An array of metalized vias isolates the traces. We describe the via metallization process that is not damaging to YBCO and compatible with dense, 2 mm period, arrays of vias.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Shocks propagate in a 2D dusty plasma with less attenuation than due to gas friction alone

In a dusty plasma, an impulsively generated shock, i.e., blast wave, was observed to decay less than would be expected due to gas friction alone. In the experiment, a single layer of microparticles was levitated in a radio frequency glow-discharge plasma. In this layer, the microparticles were self-organized as a 2D solid-like strongly coupled plasma, which was perturbed by the piston-like mechanical movement of a wire. To excite a blast wave, the wire's motion was abruptly stopped, so that the input of mechanical energy ceased at a known time. It was seen that, as it propagated across the layer, the blast wave's amplitude persisted with little decay. This result extends similar findings, in previous experiments with 3D microparticle clouds, to the case of 2D clouds. In our cloud, out-of-plane displacements were observed, lending support to the possibility that an instability, driven by wakes in the ion flow, provides energy that sustains the blast wave's amplitude despite the presence of gas damping.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

The multiwavelength view of shocks in the fastest nova V1674 Her

Classical novae are shock-powered multiwavelength transients triggered by a thermonuclear runaway on an accreting white dwarf. V1674 Her is the fastest nova ever recorded (time to declined by two magnitudes is t 2 = 1.1 d) that challenges our understanding of shock formation in novae. We investigate the physical mechanisms behind nova emission from GeV γ-rays to cm-band radio using coordinated Fermi-LAT, NuSTAR, Swift, and VLA observations supported by optical photometry. Fermi-LAT detected short-lived (18 h) 0.1–100 GeV emission from V1674 Her that appeared 6 h after the eruption began; this was at a level of (1.6 ± 0.4) × 10 −6 photons cm −2 s −1 . Eleven days later, simultaneous NuSTAR and Swift X-ray observations revealed optically thin thermal plasma shock-heated to k $T$ shock = 4 keV. The lack of a detectable 6.7 keV Fe Kα emission suggests super-solar CNO abundances. The radio emission from V1674 Her was consistent with thermal emission at early times and synchrotron at late times. The radio spectrum steeply rising with frequency may be a result of either free-free absorption of synchrotron and thermal emission by unshocked outer regions of the nova shell or the Razin–Tsytovich effect attenuating synchrotron emission in dense plasma. The development of the shock inside the ejecta is unaffected by the extraordinarily rapid evolution and the intermediate polar host of this nova.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2025

Design of Transportation Frames for 650 MHz Cavities and High Power Couplers

This work presents the design of a transportation frame system for 650~MHz superconducting radio frequency cavities with high power couplers. Modal analysis identified the coupler antenna as the critical component with a 38~Hz natural frequency, leading to a dual-frame design with wire rope isolators that achieves 82\% vibration attenuation at the critical frequency. The system meets all transportation requirements, fits within standard shipping crates, and maintains structural integrity under 12g shock loads.

42 ENGINEERING↗

DOE OSTI2025

Design of Transportation Frames for 650 MHz Cavities and High Power Couplers

Argento, Marco [Fermilab]↗

DOE OSTI2021

A ruthenium oxide thermometer for dilution refrigerators operating down to 5 mK

At the lowest temperatures achieved in dilution refrigerators, ruthenium oxide resistance thermometers often saturate and therefore lose their sensitivity. In an effort to extend the range of such temperature sensors, we built a thermometer which maintains sensitivity to 5 mK. A key component of this thermometer is an in situ radio frequency filter which is based on a modern rf absorption material. Here, we show that the use of such a filter is only effective when it is encased in the same rf-tight enclosure as the ruthenium oxide sensor. Our design delivers an attenuation level that is necessary to mitigate the effects of parasitic heating of a fraction of pW present in our circuit. Furthermore, we show that the likely origin of this parasitic heating is the black body radiation present within the experimental space of the refrigerator. We found that the equilibration time of the thermometer increases rapidly as the temperature is lowered; below 5 mK this thermometer becomes impractical because of the prohibitively long equilibration times.

47 OTHER INSTRUMENTATION↗

DOE OSTI2020

Investigating the Chemical Reactivity of Lithium Silicate Model SEI Layers

Silicon anodes suffer from an unstable solid electrolyte interphase (SEI) layer that contributes to undesirable capacity fade with cycling. A key part to addressing this unstable SEI formation is to examine how certain components of the SEI react with the electrolyte over time. One SEI component that has not been thoroughly studied in the context of the chemical reactivity against the electrolyte is lithiated silicate. Four model silicate thin films with increasing lithium content were deposited by radio frequency (RF) magnetron sputtering to study how the lithiation of the native oxide on a silicon anode affects the chemical stability of the anode surface. SiO2, Li2Si2O5, Li2SiO3, and Li3SiOx films were exposed to 1.2 M LiPF6 in the 3:7 wt% ethylene carbonate/ethyl methyl carbonate (EC/EMC) electrolyte for periods of time that are representative of the amount of time it takes to undergo cell formations. Soaked samples were rinsed, dried, and characterized by a combination of attenuated total reflectance-infrared spectroscopy (ATR-IR), focused ion beam-secondary electron microscopy (FIB-SEM), and X-ray photoelectron spectroscopy (XPS) depth profiling. It was found that the rate of the decrease in film thickness of the silicates exposed to the electrolyte over time increases as a function of the lithium content in the thin film. This reaction involves HF etching and LiPF6 salt degradation leading to silicate loss and fluorination throughout the bulk. Understanding this chemical instability is critical to determining the overall mechanism of SEI degradation over time.

ADVANCED PROPULSION SYSTEMS,ENERGY STORAGE↗

DOE OSTI2021

Underground Imaging by Sub-Terahertz Radiation

Sub-terahertz ground-penetrating radar systems offer an alternative to radio wave-based systems in the airborne imaging of buried objects. Laboratory prototype systems operating in W-band (75–110 GHz) and F-band (90–140 GHz) are presented, detecting the distance between target and source and imaging metal objects buried in mixed soil. The experimental results show that imaging in the 100–150 GHz frequency range is feasible for underground applications but significantly restricted by the attenuation characteristics of the medium covering the targets. A higher power source and more sensitive receiving components are essential to increase the penetration capability and expand the application settings of this approach.

42 ENGINEERING↗

DOE OSTI2025

Design of a shipping fixture for a compact cryomodule hermetic assembly

Two conduction-cooled 915 MHz superconducting radio frequency hermetic assemblies must be safely transported from the Jefferson Lab in Newport News, VA to General Atomics in San Diego, CA for perfor-mance testing in a custom horizontal test cryostat. One hermetic assembly consists of a 2-cell 915 MHz cavity, a coaxial fundamental power coupler, and the warm-to-cold transition beam tubes. The second hermetic assembly consists of a 2-cell 915 MHz cavity only. The assemblies will be transported on a flatbed air-ride trailer over the approximate 4000 km distance. Design requirements included adequate attenuation of 4g vertical axis, 5g beamline axis, and 1.5g lateral axis shock events. The isolation system was designed using helical wire-rope isolators with modal and transient finite element analysis performed in Ansys. Results show shock attenuation of a 10 ms half-sine pulse input to < 1g in the vertical axis, < 1.5g in the beam-line axis, and < 0.5g in the lateral axis for both assem-blies at the specified design loads and all structural stresses are kept below the material yield limits. Addi-tionally, the natural frequencies of both isolation sys-tems adequately attenuate the fundamental modes of the critical structures.

Accelerator Physics↗

DOE OSTI2023

Constraints on redshifts of blazars from extragalactic background light attenuation using Fermi - LAT data

ABSTRACT The extragalactic high-energy γ-ray sky is dominated by blazars, which are active galactic nuclei with their jets pointing towards us. Distance measurements are of fundamental importance yet for some of these sources are challenging because any spectral signature from the host galaxy may be outshone by the non-thermal emission from the jet. In this paper, we present a method to constrain redshifts for these sources that relies only on data from the Large Area Telescope on board the Fermi Gamma-ray Space Telescope. This method takes advantage of the signatures that the pair-production interaction between photons with energies larger than approximately 10 GeV and the extragalactic background light leaves on γ-ray spectra. We find upper limits for the distances of 303 γ-ray blazars, classified as 157 BL Lacertae objects, 145 of uncertain class, and 1 flat-spectrum-radio quasar, whose redshifts are otherwise unknown. These derivations can be useful for planning observations with imaging atmospheric Cherenkov telescopes and also for testing theories of supermassive black hole evolution. Our results are applied to estimate the detectability of these blazars with the future Cherenkov Telescope Array, finding that at least 21 of them could be studied in a reasonable exposure of 20 h.

Astronomy & Astrophysics↗

DOE OSTI2025

Casing Annulus Monitoring of CO 2 Injection Using Wireless Autonomous Distributed Sensor Networks

Effective and secure carbon subsurface storage, involving the deep underground injection of CO 2 into geological formations where it is permanently trapped, is paramount to mitigating CO 2 emissions (Figure I). Ensuring the integrity of these storage sites and detecting potential leakage through the casing annulus necessitates robust monitoring. This work provides the first integrated demonstration of a wireless casing-annulus monitoring architecture that can operate in highly attenuating cement-brine environments relevant to CO 2 storage. This project focused on developing and validating a novel sensor system for integration with autonomous monitoring near the cement reservoir interface. The goal was a fully integrated Technology Readiness Level (TRL) 4/5 field validation of a distributed wireless intelligent sensor system providing real-time, direct subsurface formation measurements to enhance fluid movement monitoring in the cemented casing annulus. Achieving this objective required the development and integration of 1) wireless autonomous microsensor technology by California Institute of Technology (Caltech); 2) sensor packaging and emplacement technology by Research Triangle Institute (RTI); and 3) smart well completions using wireless active casing collars and NOV pipe by the Sandia National Lab (SNL). The collaboration with the Caltech team in this project aimed to develop millimeter-scale radio frequency identification (RFID) sensors capable of detecting CO 2 , pH, and/or methane levels. These sensors are engineered to be impervious to fluids, allowing them to be mixed with cement and installed within the casing annulus. They operate using RFID protocols at frequencies of 902–928 MHz for both power and communication. A Sandia National Laboratories’ team engaged their expertise in the development of a Smart Collar system designed for the wireless data collection from these RFID sensors embedded in the cement annulus and transmission of this information to the ground surface via IntelliPipe/IntelliServ NOV drill pipe. This is accomplished through inductive coupling at the collar, which facilitates data transfer through each segment of the pipe. Because the system cannot transmit a direct current signal to power the Smart Collar, both power and communication were implemented using alternating current and electromagnetic signals at varying frequencies. Furthermore, the developed microsensor technology had to be demonstrated and validated in comparison with reference transducer measurements in a field test site at The University of Texas at Austin (UT-Austin). Although the full sensor suite did not reach field-deployment readiness, the system-level integration achieved in this project establishes a validated pathway for future incorporation of advanced microsensors.

47 OTHER INSTRUMENTATION↗