Search NASA⌕ Search

SEARCH · Search NASA

Results for “reactive metal inks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Direct Metallization with Reactive Inks – Assessment of Reliability and Process Sensitivities

This project will reduce silver consumption in photovoltaic cells by a factor of almost ten – from 95 mg/cell (the median across technologies) to 10 mg/cell. To achieve this goal, we will replace screen-printed silver pastes with contact dispensed reactive inks that produce lower resistivity metallizations at lower temperatures and with thinner films. This project will generate the understanding necessary to scale this reactive ink technology from the bench-scale to commercial throughputs. Specifically, it will combine fundamental understanding on physics and chemistries involved in contact printing of reactive inks with detailed performance and reliability studies to quantify how tightly processing parameters need to be controlled in order to reliably metallize high efficiency solar cells at commercial throughputs of 36,000 cells/hour.

14 SOLAR ENERGY↗
DOE OSTI2024

Screen-Printed Complex Ag Inks for Si HJT Metallization

Metallization using reactive metal inks has recently attracted significant research interest due to its advantages in cost of materials and manufacturing, while still achieving performance comparable to traditional fire-through particle pastes. Here, we present for the first time the use of reactive silver (Ag) inks via industrial screen-printing and inkjet printing methods for the metallization of different Si surfaces used in tunneling oxide passivating contacts (TOPCon) and Silicon heterojunction (SHJ) solar cells. Printed Ag lines exhibit a conductivity of ~5 Mu O·cm, which is approximately 3 times that of bulk Ag (1.59 µO·cm). The printed metal has a thickness of ~0.5-1.5 Mu m, an order of magnitude smaller than the current fire-through metal finger thickness (~15 Mu m). Contact resistivity measurements of the screen-printed and inkjet-printed samples on a transparent conducting oxide (TCO) surface show a very low value of ~0.2-12 mO·cm 2. Photoluminescence images of the metallized samples demonstrate minimal surface passivation degradation compared to the non-metallized areas (?iVoc <3.5 mV). Scanning electron microscopy images (SEM) reveal the structure of the printed metals on the Si surfaces as porous but much denser than fire-through Ag by nanoparticle paste. In the final presentation, we will showcase our results of printing these reactive Ag inks on high-efficiency heterojunction and TOPCon solar cells with full-area M6 wafers. Additionally, the adhesion of these reactive Ag inks on different Si surfaces according to ASTM D3359-17, as well as the performance of solar cells after standard IEC 61215 freeze/thaw and damp heat tests, will be presented. These new metal inks show promising potential as an alternative to the currently dominant particle-based pastes, offering lower Ag consumption and lower processing temperatures without compromising performance.

heterojunction solar cells↗
DOE OSTI2025

Low-Cost, Screen-Printed Silver Metal Complex Inks for Silicon Heterojunction Solar Cells

Screen printing using metal particle pastes, the current photovoltaic industry metallization standard, provides fast and reliable metal grids for silicon solar cells. Recently, metal complex or reactive metal inks are attracting research interest due to their significantly low cost and higher performance compared to traditional nanoparticle silver pastes. In this work, we demonstrate, for the first time, screen-printed high-efficiency silicon heterojunction solar cells metallized by silver metal complex inks on industrial G1-size (158.75 x 158.75 mm2) wafers. We demonstrate screen-printed Ag metal complex ink grid patterns with continuous fingers ~100-120 ..mu..m wide. The printed Ag grid is very thin (~1 ..mu..m), which is an order of magnitude thinner than the current ~20-30 ..mu..m fingers printed with low-temperature nanoparticle-based pastes. Double printing allows silicon heterojunction devices with efficiencies >20%. This is the highest efficiency so far, to our knowledge, of industrial solar cell precursors using this metallization technology. Simulation results suggested that increasing the thickness of the metal film does not significantly improve efficiency due to the dense, highly conductive films. So, a single print of ~1 ..mu..m finger would be enough to produce cells that perform similarly to a ~20 ..mu..m thick nanoparticle paste printed cells. Additionally, solar cells printed on G1 wafers with silver metal complex ink required more than 10 times less silver (~0.03 g) compared to those using silver/copper nanoparticle paste (~0.4 g of Ag). These results indicate that metal complex inks are a very promising replacement for silver nanoparticle pastes for industrial-scale metallization in an age of resource scarcity and high costs of noble metals.

14 SOLAR ENERGY↗
DOE OSTI2020

Approaching the Practical Conductivity Limits of Aerosol Jet Printed Silver

Previous efforts to directly write conductive metals have been narrowly focused on nanoparticle ink suspensions that require aggressive sintering (>200°C) and result in low-density, small-grained agglomerates with electrical conductivities <25% of bulk metal. Here, we demonstrate aerosol jet printing of a reactive ink solution and characterize high-density (93%) printed silver traces having near-bulk conductivity and grain sizes greater than the electron mean free path, while only requiring low temperature (80°C) treatment. We have developed a predictive electronic transport model which correlates the microstructure to the measured conductivity and identifies a strategy to approach the practical conductivity limit for printed metals. Our analysis of how grain boundaries and tortuosity contribute to electrical resistivity provides insight into the basic materials science that governs how an ink formulator or process developer might approach improving the conductivity. Transmission line measurements validate that electrical properties are preserved up to 20GHz, which demonstrates the utility of this technique for printed RF components. Finally, this work reveals a new method of producing robust printed electronics that retain the advantages of rapid prototyping and three-dimensional fabrication while achieving the performance necessary for success within the aerospace and communications industries.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Nickel Interlayer for Improved Silver Complex Inks Metallization in GaAs Photovoltaic Devices

Large areas of III-V photovoltaic panels are essential to supplying operational energy for a growing demand of satellites of strategic importance to the United States military, covering a range of applications. High fabrication costs and low manufacturing throughput are key barriers to meeting the necessary supply, which can in turn jeopardize mission success. At the device level, metallization based on printing of complex metal inks has attracted significant research interest due to its potential to substantially reduce processing costs and increase throughput while achieving electrical performance comparable to those of conventional metallization schemes. For GaAs photovoltaic devices, however, reliable electrical contacting remains challenging due to the formation of an interfacial oxide layer at the metal-semiconductor interface. This oxide barrier severely limits current extraction from the PV absorber, resulting in unacceptably high contact resistance. In this study, we report the introduction of a reactive nickel (Ni) interfacial layer between the silver metal fingers and the GaAs substrate to suppress oxide formation while maintaining a low-resistance electrical interface, and show performance data from fully fabricated GaAs devices incorporating the Ni interlayer. These results demonstrate the potential of reactive Ni ink as an effective interfacial layer for improved electrical contacting in low-cost PV metallization schemes.

14 SOLAR ENERGY↗
DOE OSTI2021

Corrosion of novel reactive silver ink and commercial silver-based metallizations in diluted acetic acid

Silver-based metallizations in photovoltaic modules are susceptible to corrosion by acetic acid generated in ethylene vinyl acetate encapsulated modules, resulting in power losses over time. Here, three silver-based metallizations are exposed to diluted acetic acid, in concentrations representative of that found in field-exposed modules. Compositional, morphological, and structural changes of the metallizations are studied over 3000 h of exposure to diluted acetic acid using Raman spectroscopy mapping, X-ray diffraction, and scanning electron microscopy. The three metallizations studied are: 1) a commercial high-temperature fire-through Ag paste, commonly used for Si diffused junction solar cells; 2) a commercial low-temperature paste normally used for silicon heterojunction cells; and 3) a novel low-temperature reactive silver ink shown to be suitable for photovoltaic applications. We find distinct corrosion rates for the high-temperature silver paste and reactive silver ink in the presence of diluted acetic acid. However, the low-temperature silver paste appears to be more corrosion resistant, likely due to a polymer layer that protects the silver particles.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigation of Reactive Silver Ink Formula for Reduced Silver Consumption in Silicon Heterojunction Metallization

Silver is the most expensive non-silicon component in photovoltaic cells. This is particularly salient for silicon heterojunction (SHJ) cells, which rely on large quantities of low-temperature silver pastes (LT-SP). SHJ cells would benefit greatly from an industrially scalable metallization process that simultaneously offers low silver consumption, low finger resistivities (<20 μΩ·cm), and low processing temperatures. Printed reactive silver inks (RSI) are an innovative candidate to this end. Furthermore, this work furthers the research on RSI metallization by investigating the impact of ink formula on properties pertinent to SHJ cells, including electrical properties, line width, ink splatter, silver consumption, cell performance, and adhesion. We introduce a scalable, high-throughput flexible needle contact printing approach for metallization that solves many of the issues associated with drop-on-demand printing. The printed silver fingers are characterized using electrical measurements and top-down and cross-sectional microscopy. The best performing ink, consisting of silver acetate, ethylamine, and formic acid, achieved silver fingers with total resistivities of 3.1 μΩ·cm and contact resistivities of 3.2 mΩ·cm 2 when printed at 61 °C. This ink metallized a full-sized 156 mm × 156 mm SHJ cell. This is the first reported data for RSI metallization of a full-sized SHJ cell and shows how an optimized RSI can achieve similar performances to LT-SP while consuming 80–90% less silver.

14 SOLAR ENERGY↗
DOE OSTI2022

All-atmospheric fabrication of Ag–Cu core–shell nanowire transparent electrodes with Haacke figure of merit >600 × 10–3 Ω−1

Abstract Transparent conducting electrodes (TCEs) are essential components in devices such as touch screens, smart windows, and photovoltaics. Metal nanowire networks are promising next-generation TCEs, but best-performing examples rely on expensive metal catalysts (palladium or platinum), vacuum processing, or transfer processes that cannot be scaled. This work demonstrates a metal nanowire TCE fabrication process that focuses on high performance and simple fabrication. Here we combined direct and plating metallization processes on electrospun nanowires. We first directly metallize silver nanowires using reactive silver ink. The silver catalyzes subsequent copper plating to produce Ag–Cu core–shell nanowires and eliminates nanowire junction resistances. The process allows for tunable transmission and sheet resistance properties by adjusting electrospinning and plating time. We demonstrate state-of-the-art, low-haze TCEs using an all-atmospheric process with sheet resistances of 0.33 Ω sq −1 and visible light transmittances of 86% (including the substrate), leading to a Haacke figure of merit of 652 × 10 –3 Ω −1 . The core–shell nanowire electrode also demonstrates high chemical and bending durability.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Importance of the Heat Treatment Scheme on Self-Reducing Reactive Silver Inks

Self-reducing reactive silver inks can print high-quality silver at reasonable temperatures. While numerous studies have explored the impact of processing temperature on electrical properties, the role of the heat treatment scheme has not yet been studied. Common heat treatment schemes include printing and drying inks at room temperature before heat treatment, performing heat treatments while the inks are still wet, and directly printing the inks onto heated substrates. Each scheme generates distinct heat transfer and mass transport kinetics that can affect the silver morphology and electrical properties. However, to date, the impact of different schemes has not been systematically investigated. To address this knowledge gap, this work investigates how different heat treatment schemes impact metal formation, sintering, and the resultant electrical properties of printed self-reducing reactive silver inks. Heat treatment on room-temperature dried inks and wet inks, with top-down (oven) and bottom-up (hot plate) heating sources, were compared. Inks dried at room temperature resulted in extremely porous films that required high heat treatment temperatures (>100 °C) for silver densification. However, these dried films could only densify locally, and their high initial porosities resulted in voids and high resistances (~0.6 Ω mm –1 ) even after heat treatments above 300 °C. Inks that were wet during heat treatment showed moderate improvements in electrical properties with resistances on the order of 0.4 Ω mm –1 at heat treatments of 250 °C. Printing reactive inks directly onto heated substrates yielded the best low-temperature results, with 0.46 Ω mm –1 (5.5 × bulk silver) line resistances achieved at only 90 °C. Overall, this work’s experimental results provide detailed insights into why printing onto a heated substrate results in superior electrical performance compared to more common heat treatment schemes. Additionally, controlling where the precipitation reaction occurs is critical to controlling the film morphology and properties. As a result, this work shows that even an ammonia-based silver reactive ink can achieve good, low-temperature electrical properties with the proper heat treatment scheme.

14 SOLAR ENERGY↗
DOE OSTI2026

Hybrid Additive Manufacturing and Electric Field-Assisted Sintering of High-temperature Heat Exchangers via Sacrificial Channel Molds

A hybrid manufacturing approach, integrating additive manufacturing (AM) with powder methodology via electric field-assisted sintering (EFAS), was developed for the fabrication of high-temperature compact heat exchangers (CHX) from refractory metals. The methodology employed additively manufactured sacrificial channel molds (SCMs) as shapeholders for CHX channels, which were embedded in metal powders using EFAS. Following embedding, the SCMs were chemically dissolved to form the internal channel network. SCMs were fabricated using both digital light processing (DLP) and direct ink writing (DIW) from chemically reactive, calcium-based ceramic feedstocks with varying ratios of Al2O3 reinforcement. The microstructure, phase composition, and dissolution behavior of both as-printed and embedded SCMs were investigated. The shrinkage behavior of the SCMs embedded in refractory metals, as well as the interfacial characteristics between the SCMs and metal matrix, were studied. The results showed that the SCMs containing sufficient chemical reactive ceramics dissolved effectively before and after embedding. The as-printed SCMs retained the phase composition of their feedstocks, but the embedded SCMs containing calcium-based ceramics and Al2O3 exhibited the formation of calcium aluminates due to high temperature exposure during embedding. Most SCMs exhibited a cellular Al2O3 network filled with Ca-rich ceramics. Shrinkage after embedding was strongly dependent on SCM density, with lower density SCMs exhibiting greater shrinkage. A thin SCM-affected zone was observed at the metal matrix surface, characterized by increased porosity compared to the bulk matrix. This effect was attributed to infiltration of the SCM materials into powder particle boundaries under pressure, followed by their removal during dissolution. This study demonstrates the feasibility of manufacturing CHXs from hard-to-process refractory metals for use in harsh environments.

36 - MATERIALS SCIENCE↗
NASA NTRS1981

Molybdenum-tin as a solar cell metallization system

The operations of solar cell manufacture are briefly examined. The formation of reliable, ohmic, low-loss, and low-cost metal contacts on solar cells is a critical process step in cell manufacturing. In a commonly used process, low-cost metallization is achieved by screen printing a metal powder-glass frit ink on the surface of the Si surface and the conductive metal powder. A technique utilizing a molybdenum-tin alloy for the metal contacts appears to lower the cost of materials and to reduce process complexity. The ink used in this system is formulated from MoO3 with Sn powder and a trace amount of titanium resonate. Resistive losses of the resulting contacts are low because the ink contains no frit. The MoO3 is finally melted and reduced in forming gas (N2+H2) to Mo metal. The resulting Mo is highly reactive which facilitates the Mo-Si bonding.

Boyd, D. W.↗
DOE OSTI2024

Large area nanoscale patterning of functional materials using organosilicate ink based nanotransfer printing

Abstract This paper presents a versatile nanotransfer printing method for achieving large-area sub-micron patterns of functional materials. Organosilicate ink formulations combined with effective release layers have been shown to facilitate patterning of materials through the commonly used patterning approaches—lift off, physical etching and chemical etching. In this paper, we demonstrate that organosilicate ink formulations function as an effective resist owing to its superior physico-chemical stability whereas the release layers ensure clean removal of the resist post patterning. We successfully demonstrate patterning of sub-micron structures (800 nm feature sizes) of chromium metal through the lift off approach, silicon through reactive ion etching technique and silicon dioxide through wet chemical etching technique illustrating the versatility of the reported method. This patterning methodology represents a significant advancement in enabling nanostructure fabrication within resource-constrained laboratories. The approach requires nothing more than a master mold containing the desired structures, a spin coater, a low-temperature hotplate, and a desktop reactive ion etch tool.

Engineering↗
DOE OSTI2021

Ligand Locking on Quantum Dot Surfaces via a Mild Reactive Surface Treatment

At the outermost surface of colloidal QDs are organic surface ligands which dynamically bind and release in solution to control the growth kinetics, control the size/shape of the crystals, passivate surface states, and provide colloidal stability through favorable interactions with the solvent. However, the dynamicity comes at the expense of the stability of the QD suspension. Here, we show that ligands can be permanently locked on the QD surface by a thin layer of an inert metal oxide which forms within the ligand shell, over the headgroup. By interrogating the surface chemistry with different spectroscopic methods, we prove the ligand locking on the QD surface. As a result, an exceptional stability of the coated QD inks is achieved in a wide concentration range, even in the presence of chemically competing surface ligands in solution. We anticipate that this critical breakthrough will benefit different areas related to colloidal QDs, spanning from single-particle studies to displays and solar cells and biological applications. Furthermore, the same chemistry could be easily translated to surface treatments of bulk materials and thin films.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1985

Real-time SEM studies in controlled reactive atmospheres

A unique scanning electron accessory has been developed that allows the observation of specimens under partial pressures of any gas. The sample is placed in a metal support boat inside a special sample holder. The sample in the boat is imaged on a CRT and is simultaneously recorded on a videotape, allowing the reaction between the sample and the gas to be observed in real time. Sample changes can be seen continuously as the sample is being heated or cooled. This process allows the observation of material transformations such as phase changes as they happen. Temperatures as high as 1000 C have been used and are continuously monitored using a thermocouple with a digital display on the CRT and videotape. X-ray analyses can also be run before and after any reactions. In the study described here, thick-film screen-printing inks using molybdenum/tin compositions as a replacement for silver were developed to be used on terrestrial photovoltaic cells. Pieces were placed on the sample stage and heated in both O2 and H2 atmospheres. The results were used to determine the most effective frits to be used in the thick-film inks.

Gallagher, B. D.↗
DOE OSTI2023

Laboratory-Scale Coal-Derived Graphene Process (Final Report)

The Energy & Environmental Research Center (EERC) conducted a laboratory-scale coal-derived graphene (CDG) project focused on developing a technological process for making graphene from four U.S. domestic coal or coal wastes, including lignite from North Dakota, subbituminous coal from Wyoming, bituminous coal from Utah, and anthracite from Pennsylvania. The project was divided into two performance or budget periods (BPs), with BP1 comprising the up-front laboratory experiments to make graphene materials from coal beginning on May 1, 2020, to April 30, 2022. BP2 was conducted from May 1, 2022, to April 30, 2023, and was focused on analyzing the CDG process economic feasibility and the technical gaps for technological scale-up and commercialization. During this project, a few different coal-derived high-value products have been demonstrated, including graphite, graphene oxide (GO), reduced graphene oxide (rGO), and graphene quantum dots (GQDs). A new graphite microstructure was discovered and named “croissant graphite” because of the exterior morphological and textural resemblance to croissant food items sold in commercial groceries stores. The new graphite structure and the associated preparation from coal or coal waste feedstocks has been the subject of a U.S. patent application. The systematic experimental processes involving coal cleaning, upgrading, and conversion to high-value carbon products culminated into a developed upgraded coal-to-products (UCP) technology that is being pursued for potential fast-track commercialization, if funding is available. It is envisioned that commercialization of the UCP technology would increase consumption of U.S. domestic coals or coal wastes to make environmentally sustainable high-value products for the electronics industry, high-energy-storage applications, and clean energy technologies such as electric vehicle (EV) lithium-ion batteries (LIBs), for which graphite has become a critical mineral commodity. Croissant graphite microstructures, when observed by field emission scanning electron microscopy (FESEM), display wavy surface morphology and often grow from a base that is made of graphitized particles with honeycomb-like layers, which are believed to be graphene layers. While more studies are needed to fully ascertain the mechanisms of the croissant graphite microstructure formation, it is postulated that their growth may begin from curling of the graphene sheets into ribbon-like structures, and continuous growth and densification of the ribbon-like structures forms croissant microstructures. Additional studies are ongoing to evaluate the electrochemical performance of croissant graphite for LIB applications and to determine the experimental conditions necessary to tune on/off croissant formation so that it can be either optimized or suppressed depending on performance evaluation results. In addition to the discovery of croissant graphite, the graphitization process from the four coal ranks in general was successful. X-ray diffraction (XRD) analysis showed that the degree of graphitization (DoG) ranged from 12% to 80% in an early sample set, and further optimization on lignite coal produces a DoG of about 92%, which was spectacular to see as lignite is the lowest-rank coal. Thus, it is expected that the graphitization performance for higher-rank coals will be similar or better when optimized as well. The coal-derived graphite was used to make GO and rGO. Analytical characterization, e.g., by methods such as Raman spectroscopy, XRD, Fourier transform infrared (FTIR) spectroscopy and FESEM, showed that the sequence of converting the coal to graphite, exfoliating it to GO, and then chemically reducing the GO to rGO was successful. Although coal naturally contains aromatic compounds and some relatively small-sized condensed aromatic units, it does not contain graphene sheets. In the UCP process, the aromatic domains in the coals, particularly low-rank coals, are concentrated and condensed further into graphene sheets, which are ordered into a 3D stack during graphitization. The synthesized graphite is then unpacked by methods such as exfoliation to various graphene products. GQDs were synthesized from all four coal types, and their optical properties were demonstrated to be tunable by the coal precursor preprocessing treatments. In all four coal types, enhanced optical properties were observed for the produced GDQs with incremental improvements made to the coal precursors. GQDs produced from raw coal samples displayed lower ultraviolet–visible (UV–Vis) spectroscopy absorbance intensity compared to those obtained from cleaned and upgraded coal residues. The photoluminescence (PL) intensities also varied with pretreatment conditions and with the concentration of GQDs in aqueous solutions. GQDs obtained from anthracite show longer emission wavelengths and can be excited by visible light as opposed to GQDs derived from the other coal ranks. UV fluorescence 3D maps and spectra revealed that the emission wavelength at which the GQDs solutions display the highest intensity was slightly redshifted based on the coal precursor pretreatments. In low-rank coal (lignite and subbituminous) samples, two clusters were observed in the maps for GQDs, which may suggest that there are potentially two types of fluorophores in solution or two main size populations. The ability to tune the properties of GQDs based on processing methods can be exploited to make GQDs for various optical display or optoelectronics applications. The results also highlight the importance of removing coal-borne impurities to improve the quality of the coal precursor for preparation of graphene products. Coal and/or coal wastes preprocessing methods were developed and applied to clean and upgrade the coal precursors prior to graphitization and subsequent conversion to graphene products. The preprocessing methods involve high specific-gravity separations, mineral acid cleaning (no hydrofluoric acid), and subsequent upgrading by reducing the coal-borne heteroatom (nitrogen, sulfur, and oxygen) content using proprietary chemical agents. Analytical characterization revealed that the preprocessing steps were successful, with ash reductions that range from 38% to 80% and residual ash content that was below the 5 wt% initial target. Based on proximate and ultimate analysis, the heteroatom reduction reactions produced upgraded coal residues with the oxygen content reduced by 8% to 24%, with additional reductions in the nitrogen and sulfur contents. An initial assessment of the waste streams from the UCP process shows very small to negligible environmental impact due to CO 2 , NO x , and SO x because most process steps are performed under inert atmosphere with argon. Consequently, reactive oxygen environments that tend to create these species are avoided. The inorganic and potentially hazardous species are released into aqueous waste streams that are easy to handle for proper disposal. The liquid waste streams were found to contain low-level concentrations of rare-earth elements (REEs), which could be concentrated and recovered as value-added by-products. Additionally, the volatile and gaseous fractions from carbonization and heat treatment contain useful organic compounds that can also be recovered as potential valuable by-products. Thus, the UCP technology is considered an environmentally sustainable and promising emerging technology for making high-value products from coal and coal wastes, with potential additional value-added by-products. Analysis of potential markets for the coal-derived carbon products shows a strong demand in both niche market sectors and across a wide variety of other industrial sectors. Graphite is currently considered a critical mineral commodity that has a large and growing demand in the LIB industry for EV applications. Based on data from Fortune Business Insights (2022) and Marketwatch (2023) reports, the average global graphite market is projected to reach about 33 billion by 2028, growing at a compound annual growth rate (CAGR) of about 7%, with much of this growth expected to be in the LIB industry. GO and rGO have strong market potentials in various application areas, such as coatings for anticorrosion, anti-icing, and antimicrobial protection, thermal barriers, wear resistance, sensors, additive manufacturing such as 3D inks, and others. GQDs are the emerging key player in the bioimaging, photovoltaics, and light-emitting diodes (LEDs) applications, with the potential to replace traditional semiconductor quantum dots (SQDs), which are based on metallic systems that are more toxic and more expensive. Biomedical applications of GQDs are becoming more attractive because of low to no toxicity and extremely low cost compared to SQDs. The major challenges for scale-up and commercialization of coal-derived carbon products such as graphene vary from the inherent attributes of graphene itself to reluctance to accept graphene in new manufacturing processes because of the uncertainty of the unknown. The 2D nature of graphene materials with a thickness of one atom presents significant challenges to proper handling/processing, and process scale-up becomes difficult because it requires high-end, expensive equipment, even for routine handling and analysis for quality assurance and control. Pristine graphene can also be extremely difficult to work into other matrices, thus hindering downstream processibility, especially at large scale. Currently, the cost of graphene and graphene products is still high and presents an economic risk that tends to slow down investment in scaling up emerging technologies. The lack of a standard for graphene materials for quality assurance and quality control poses a great challenge not only for the markets but also for commercialization efforts. A first-look economic feasibility analysis of the UCP technology provided valuable information that suggests the UCP process would be feasible, especially when it is scaled to a pilot scale and could be more competitive at the full scale. Graphitization was found to be the most energy-consuming and most capital-intensive step in the overall process. In small laboratory- and bench-scale experiments, labor is a significant contributor to the total process costs. Although these energy, capital, and labor constraints contribute to a higher selling price for the product, a preliminary economic model suggests that the process would be feasible at large scale when the process is fully integrated, optimized, and automated.

01 COAL, LIGNITE, AND PEAT↗