SEARCH · Search NASA

Results for “realtime measurements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS1996

Measuring Motor-Shaft Clearance And Wobble During Operation

Noncontact proximity sensor, preferably eddy-current liftoff probe, provides realtime measurement of distance and small variations of distance between two mechanical components designed to be maintained at precise, fixed distance. In particular, system intended for use in measuring lateral clearance and variations in lateral clearance (wobble) of motor shaft relative to motor housing while shaft turning. Provides early indication of wear in motor bearings. Rate of rotation also measured.

Chern, Engmin James↗

NASA NTRS1995

The Deep Space Network stability analyzer

A stability analyzer for testing NASA Deep Space Network installations during flight radio science experiments is described. The stability analyzer provides realtime measurements of signal properties of general experimental interest: power, phase, and amplitude spectra; Allan deviation; and time series of amplitude, phase shift, and differential phase shift. Input ports are provided for up to four 100 MHz frequency standards and eight baseband analog (greater than 100 kHz bandwidth) signals. Test results indicate the following upper bounds to noise floors when operating on 100 MHz signals: -145 dBc/Hz for phase noise spectrum further than 200 Hz from carrier, 2.5 x 10(exp -15) (tau =1 second) and 1.5 x 10(exp -17) (tau =1000 seconds) for Allan deviation, and 1 x 10(exp -4) degrees for 1-second averages of phase deviation. Four copies of the stability analyzer have been produced, plus one transportable unit for use at non-NASA observatories.

Breidenthal, Julian C.↗

NASA NTRS2001

A Thin Film Multifunction Sensor for Harsh Environments

The status of work at NASA Glenn Research Center to develop a minimally intrusive integrated sensor to provide realtime measurement of strain, heat flux and flow in high temperature environments is presented in this paper. The sensor can be beneficial as a single package to characterize multiple stress and strain modes simultaneously on materials and components during engine development and validation. A major technical challenge is to take existing individual gauge designs and modify them into one integrated thin film sensor. Ultimately, the goal is to develop the ability to deposit the sensors directly onto internal engine parts or on a small thin substrate that can be attached to engine components. Several prototype sensors constructed of platinum, platinum-rhodium alloy, and alumina on constant-strain alumina beams have been built and bench-tested. The technical challenges of the design. construction, and testing are discussed. Data from the preliminary testing of the sensor array is presented. The future direction for the sensor development is discussed as well.

Wrbanek, John D.↗

NASA NTRS2011

Comparative Validation of Realtime Solar Wind Forecasting Using the UCSD Heliospheric Tomography Model

The University of California, San Diego 3D Heliospheric Tomography Model reconstructs the evolution of heliospheric structures, and can make forecasts of solar wind density and velocity up to 72 hours in the future. The latest model version, installed and running in realtime at the Community Coordinated Modeling Center(CCMC), analyzes scintillations of meter wavelength radio point sources recorded by the Solar-Terrestrial Environment Laboratory(STELab) together with realtime measurements of solar wind speed and density recorded by the Advanced Composition Explorer(ACE) Solar Wind Electron Proton Alpha Monitor(SWEPAM).The solution is reconstructed using tomographic techniques and a simple kinematic wind model. Since installation, the CCMC has been recording the model forecasts and comparing them with ACE measurements, and with forecasts made using other heliospheric models hosted by the CCMC. We report the preliminary results of this validation work and comparison with alternative models.

MacNeice, Peter↗

NASA NTRS2019

Real-Time UAV Trajectory Prediction for Safety Monitoring in Low-Altitude Airspace

The rising number of small unmanned aerial vehicles (UAVs) expected in the next decade will enable a new series of commercial, service, and military operations in low altitude airspace as well as above densely populated areas. These operations may include on-demand delivery, medical transportation services, law enforcement operations, traffic surveillance and many more. Such unprecedented scenarios create the need for robust, efficient ways to monitor the UAV state in time to guarantee safety and mitigate contingencies throughout the operations. This work proposes a generalized monitoring and prediction methodology that utilizes realtime measurements of an autonomous UAV following a series of way-points. Two different methods, based on sinusoidal acceleration profiles and high-order splines, are utilized to generate the predicted path. The monitoring approach includes dynamic trajectory re-planning in the event of unexpected detour or hovering of the UAV during flight. It can be further extended to different vehicle types, to quantify uncertainty affecting the state variables, e.g., aerodynamic and other environmental effects, and can also be implemented to prognosticate safety-critical metrics which depend on the estimated flight path and required thrust. The proposed framework is implemented on a simplified, scalable UAV modeling and control system traversing 3D trajectories. Results presented include examples of real-time predictions of the UAV trajectories during flight and a critical analysis of the proposed scenarios under uncertainty constraints.

UAV trajectory prognosis↗

DOE OSTI2022

Capturing the microbial volatilome: an oft overlooked 'ome'

Among the diverse metabolites produced by microbial communities, some are volatile. Volatile organic compounds (VOCs) are vigorously cycled by microbes as metabolic substrates and products and as signaling molecules. Yet, current microbial metabolomic studies predominantly focus on nonvolatile metabolites and overlook VOCs, which therefore represent a missing component of the metabolome. Advances in VOC detection now allow simultaneous observation of the numerous VOCs constituting the ‘volatilome’ of microbial systems. Here, we present a roadmap for integrating and advancing VOC and other ‘omics approaches and highlight the potential for realtime VOC measurements to help overcome limitations in discrete ‘omics sampling. Including volatile metabolites in metabolomics, both conceptually and in practice, will build a more comprehensive understanding of microbial processes across ecological communities.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS1984

Method and apparatus for calibrating the ionosphere and application to surveillance of geophysical events

The columnar electron content of the ionosphere between a spacecraft and a receiver is measured in realtime by cross correlating two coherently modulated signals transmitted at different frequencies (L1,L2) from the spacecraft to the receiver using a cross correlator. The time difference of arrival of the modulated signals is proportional to electron content of the ionosphere. A variable delay is adjusted relative to a fixed delay in the respective channels (L1,L2) to produce a maximum at the cross correlator output. The difference in delay required to produce this maximum is a measure of the columnar electron content of the ionosphere. A plurality of monitoring stations and spacecraft (Global Positioning System satellites) are employed to locate any terrestrial event that produces an ionospheric disturbance.

Macdoran, P. F.↗

NASA NTRS2014

CO2 Washout Testing Using Various Inlet Vent Configurations in the Mark-III Space Suit

Requirements for using a space suit during ground testing include providing adequate carbon dioxide (CO2) washout for the suited subject. Acute CO2 exposure can lead to symptoms including headache, dyspnea, lethargy and eventually unconsciousness or even death. Symptoms depend on several factors including inspired partial pressure of CO2 (ppCO2), duration of exposure, metabolic rate of the subject and physiological differences between subjects. Computational Fluid Dynamic (CFD) analysis has predicted that the configuration of the suit inlet vent has a significant effect on oronasal CO2 concentrations. The main objective of this test was to characterize inspired oronasal ppCO2 for a variety of inlet vent configurations in the Mark-III suit across a range of workload and flow rates. Data and trends observed during testing along with refined CFD models will be used to help design an inlet vent configuration for the Z-2 space suit. The testing methodology used in this test builds upon past CO2 washout testing performed on the Z-1 suit, Rear Entry I-Suit (REI) and the Enhanced Mobility Advanced Crew Escape Suit (EM-ACES). Three subjects performed two test sessions each in the Mark-III suit to allow for comparison between tests. Six different helmet inlet vent configurations were evaluated during each test session. Suit pressure was maintained at 4.3 psid. Suited test subjects walked on a treadmill to generate metabolic workloads of approximately 2000 and 3000 BTU/hr. Supply airflow rates of 6 and 4 actual cubic feet per minute (ACFM) were tested at each workload. Subjects wore an oronasal mask with an open port in front of the mouth and were allowed to breathe freely. Oronasal ppCO2 was monitored real-time via gas analyzers with sampling tubes connected to the oronasal mask. Metabolic rate was calculated from the total oxygen consumption and CO2 production measured by additional gas analyzers at the air outlet from the suit. Realtime metabolic rate measurements were used to adjust the treadmill workload to meet target metabolic rates. This paper provides detailed descriptions of the test hardware, methodology and results, as well as implications for future inlet vent designs and ground testing.

Korona, F. Adam↗

DOE OSTI2021

Scale Up of High-Performance REBCO Tapes in a Pilot-Scale Advanced MOCVD Tool With In-Line 2D-XRD System

We have reported the development of an Advanced Metal-Organic Chemical Vapor Deposition (AMOCVD) method featuring ohmic heating of the substrate for REBCO film growth, direct tape temperature monitoring, and laminar precursor flow. This A-MOCVD method has been used to fabricate 4 – 5 m thick film REBCO tapes with record high performance: critical currents exceeding 8700 A/12 mm at 30 K, 3 T; and engineering current density of 5200 A/mm 2 at 4.2 K, 15 T. Recently, we constructed a pilot-scale reel-to-reel A-MOCVD system to scale up the technology to long tapes. Preliminary batches of tapes exhibit consistent performance and good uniformity along the length. An in-line 2D X-ray Diffraction (XRD) system has been integrated into the pilot A-MOCVD tool to monitor the REBCO texture and composition, RE 2 O 3 content, and the dimensions of BaMO 3 (BMO, M=Zr,Hf) nanorods that act as artificial pinning centers. Specifically, the streaking angle between REBCO (103) and BZO (101) has been found to correlate well with (Ba+M)/Cu of the film, lift factor in critical current over a range of temperatures and magnetic fields, and the size of the BMO nanorods. Furthermore, the in-line 2D-XRD is expected to serve as a valuable quality measuring tool supporting realtime feedback control for the process to yield uniform and consistent manufacturing of high performance REBCO tapes by Advanced MOCVD.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS2008

ULTOR(Registered TradeMark) Passive Pose and Position Engine For Spacecraft Relative Navigation

The ULTOR(Registered TradeMark) Passive Pose and Position Engine (P3E) technology, developed by Advanced Optical Systems, Inc (AOS), uses real-time image correlation to provide relative position and pose data for spacecraft guidance, navigation, and control. Potential data sources include a wide variety of sensors, including visible and infrared cameras. ULTOR(Registered TradeMark) P3E has been demonstrated on a number of host processing platforms. NASA is integrating ULTOR(Registerd TradeMark) P3E into its Relative Navigation System (RNS), which is being developed for the upcoming Hubble Space Telescope (HST) Servicing Mission 4 (SM4). During SM4 ULTOR(Registered TradeMark) P3E will perform realtime pose and position measurements during both the approach and departure phases of the mission. This paper describes the RNS implementation of ULTOR(Registered TradeMark) P3E, and presents results from NASA's hardware-in-the-loop simulation testing against the HST mockup.

Hannah, S. Joel↗

DOE OSTI2020

HIDES: Hybrid Intrusion Detector for Energy Systems

The establishment of a resilient electric grid accompanied by a secure communications network is an ongoing battle as advanced persistent threats continue to exploit existing vulnerabilities in legacy supervisory control and data acquisition system (SCADA) infrastructure. Traditional intrusion detection systems (IDSs) lack consistent performance because of the continuously evolving attack surface of SCADA systems. These shortcomings can be overcome by integrating logical system behavior, protocol-specific knowledge, and data-based learning to develop a comprehensive IDS solution. In this paper, we present a Hybrid Intrusion Detector for Energy Systems by integrating a network-based IDS, state-of-the-art machine learning-based IDS, and model-based IDS to detect unknown and stealthy cyberattacks targeting the SCADA networks. The proposed IDS uses synchrophasor measurements and cyber logs to learn patterns of different scenarios based on spatiotemporal behaviors of power systems. As a proof of concept, we implement and validate the proposed IDS by leveraging resources available at the National Renewable Energy Laboratory's Energy Systems Integration Facility test bed. Experimental results show promising performance in detecting cyberattacks while providing realtime visualization of power system measurements and cyber logs.

machine-learning intrusion detection system↗

DOE OSTI2020

Hydrogen Contamination Detector: Protecting the future of zero-emission fuel cell energy [Brief]

Los Alamos National Laboratory developed an electrochemical detector to protect zero-emission hydrogen fuel cells from contaminated fuels. Fuel cells power environmentally clean vehicles, fork lifts, drones, and provide auxiliary power. High-purity hydrogen is essential to avoid poisoning fuel cells. Current analysis methods are costly and cannot detect impurities in realtime. The Hydrogen Contamination Detector measures the two highest impact Department of Energy-identified impurities with a simple, low-cost unit that provides 24/7, point-of-service analysis. Los Alamos partnered with H2Frontiers to conduct field trials at hydrogen refueling stations and with Skyre LLC for commercialization through a DOE Technology Commercialization Fund project.

08 HYDROGEN↗

NASA NTRS2010

NASA's STEREO Mission

NASA's Solar-TErrestrial Relations Observatory mission, launched in 2006 October, consists of two nearly identical spacecraft in heliocentric orbits and currently 1380 of heliolongitude apart. Instrumentation on both spacecraft monitor solar wind plasma and magnetic field parameters, energetic particles, radio flux, and provide EUV and visible-light imaging of the corona, as well as novel, visible-light images of the ecliptic heliosphere. In addition to higher-resolution telemetry that enables a broad range of research into the propagation of disturbances in the inner heliosphere, a low-bandwidth, space weather beacon telemetry stream provides near-realtime information on each of these measurement types.

Gurman, Joseph B.↗

NASA NTRS1999

TRMM Realtime Data Production, Transfer, and Future Plans

The Tropical Rainfall Measuring Mission, a joint US NASA and Japan NASDA mission, was launched on November 27, 1997 from Tanegashima Island, Japan on a NASDA provided H-II launch vehicle. The TRMM objectives are: to obtain and study multi-year science data sets of tropical and sub- tropical rainfall measurement; to understand how interactions between the sea, air, and land masses produce changes in global rainfall and climate; to help improve modeling of tropical rainfall processes; to test, evaluate, and improve the performance of satellite rainfall estimates measurements and techniques. The routine production and quick distribution of standard products provides an important underpinning to these objectives. The determination of standard TRMM algorithms and the requirements for routine production and distribution fall within the authority of the joint US-Japan Science Team. In April of 1998, the Joint TRMM Science team requested that TRMM data be made available in near real-time to approved international agencies and modelers. This request was an addition to the routine production of the standard TRMM data products. The science team requested that near-realtime products be as small as possible to facilitate their transfer via networks. Indeed, it was determined that only network transfer would be available. This presentation provides an overview of the type of products available from the realtime system and how the TRMM system was developed at the lowest cost in the shortest amount of time. It then describes the real-time data flow. The presentation also summarizes how the science quality of real-time data is maintained. It describes how interested groups can get access to this data and the importance of networks for the future of real-time data expansion. The presentation concludes real-time possibilities and improvements possible as part of the proposed Global Precipitation Mission. High speed network access availability is an important catalyst to real-time data flow during the proposed mission.

Stocker, Erich Franz↗

DOE OSTI2024

The data acquisition system of the LZ dark matter detector: FADR

The Data Acquisition System (DAQ) for the LUX-ZEPLIN (LZ) dark matter detector is described. The signals from 745 PMTs, distributed across three subsystems, are sampled with 100-MHz 32-channel digitizers (DDC-32s). A basic waveform analysis is carried out on the on-board Field Programmable Gate Arrays (FPGAs) to extract information about the observed scintillation and electroluminescence signals. This information is used to determine if the digitized waveforms should be preserved for offline analysis. The system is designed around the Kintex-7 FPGA. In addition to digitizing the PMT signals and providing basic event selection in real time, the flexibility provided by the use of FPGAs allows us to monitor the performance of the detector and the DAQ in parallel to normal data acquisition. Furthermore, the hardware and software/firmware of this FPGA-based Architecture for Data acquisition and Realtime monitoring (FADR) are discussed and performance measurements are described.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

NASA NTRS2006

Realtime Multichannel System for Beat to Beat QT Interval Variability

The measurement of beat-to-beat QT interval variability (QTV) shows clinical promise for identifying several types of cardiac pathology. However, until now, there has been no device capable of displaying, in real time on a beattobeat basis, changes in QTV in all 12 conventional leads in a continuously monitored patient. While several software programs have been designed to analyze QTV, heretofore, such programs have all involved only a few channels (at most) and/or have required laborious user interaction or offline calculations and postprocessing, limiting their clinical utility. This paper describes a PC-based ECG software program that in real time, acquires, analyzes and displays QTV and also PQ interval variability (PQV) in each of the eight independent channels that constitute the 12lead conventional ECG. The system also processes certain related signals that are derived from singular value decomposition and that help to reduce the overall effects of noise on the realtime QTV and PQV results.

Starc, Vito↗

NASA NTRS2017

Global Clear-Sky Surface Skin Temperature from Multiple Satellites Using a Single-Channel Algorithm with Angular Anisotropy Corrections

Surface skin temperature (T(sub s)) is an important parameter for characterizing the energy exchange at the ground/water-atmosphere interface. The Satellite ClOud and Radiation Property retrieval System (SatCORPS) employs a single-channel thermal-infrared (TIR) method to retrieve T(sub s) over clear-sky land and ocean surfaces from data taken by geostationary Earth orbit (GEO) and low Earth orbit (LEO) satellite imagers. GEO satellites can provide somewhat continuous estimates of T(sub s) over the diurnal cycle in non-polar regions, while polar T(sub s) retrievals from LEO imagers, such as the Advanced Very High Resolution Radiometer (AVHRR), can complement the GEO measurements. The combined global coverage of remotely sensed T(sub s), along with accompanying cloud and surface radiation parameters, produced in near-realtime and from historical satellite data, should be beneficial for both weather and climate applications. For example, near-realtime hourly T(sub s) observations can be assimilated in high-temporal-resolution numerical weather prediction models and historical observations can be used for validation or assimilation of climate models. Key drawbacks to the utility of TIR-derived T(sub s) data include the limitation to clear-sky conditions, the reliance on a particular set of analyses/reanalyses necessary for atmospheric corrections, and the dependence on viewing and illumination angles. Therefore, T(sub s) validation with established references is essential, as is proper evaluation of T(sub s) sensitivity to atmospheric correction source. This article presents improvements on the NASA Langley GEO satellite and AVHRR TIR-based T(sub s) product that is derived using a single-channel technique. The resulting clear-sky skin temperature values are validated with surface references and independent satellite products. Furthermore, an empirically adjusted theoretical model of satellite land surface temperature (LST) angular anisotropy is tested to improve satellite LST retrievals. Application of the anisotropic correction yields reduced mean bias and improved precision of GOES-13 LST relative to independent Moderate-resolution Imaging Spectroradiometer (MYD11_L2) LST and Atmospheric Radiation Measurement Program ground station measurements. It also significantly reduces inter-satellite differences between LSTs retrieved simultaneously from two different imagers. The implementation of these universal corrections into the SatCORPS product can yield significant improvement in near-global-scale, near-realtime, satellite-based LST measurements. The immediate availability and broad coverage of these skin temperature observations should prove valuable to modelers and climate researchers looking for improved forecasts and better understanding of the global climate model.

Scarino, Benjamin R.↗

DOE OSTI2021

A nudged hybrid analysis and modeling approach for realtime wake-vortex transport and decay prediction

Here, we put forth a long short-term memory (LSTM) nudging framework for the enhancement of reduced order models (ROMs) of fluid flows utilizing noisy measurements for air traffic improvements. Toward emerging applications of digital twins in aviation, the proposed approach allows for constructing a realtime predictive tool for wake-vortex transport and decay systems. We build on the fact that in realistic application, there are uncertainties in initial and boundary conditions, model parameters, as well as measurements. Moreover, conventional nonlinear ROMs based on Galerkin projection (GROMs) suffer from imperfection and solution instabilities, especially for advection-dominated flows with slow decay in the Kolmogorov n-width. In the presented LSTM nudging (LSTM-N) approach, we fuse forecasts from a combination of imperfect GROM and uncertain state estimates, with sparse Eulerian sensor measurements to provide more reliable predictions in a dynamical data assimilation framework. We illustrate our concept by solving the two-dimensional vorticity transport equation. We investigate the effects of measurements noise and state estimate uncertainty on the performance of the LSTM-N behavior. We also demonstrate that it can sufficiently handle different levels of temporal and spatial measurement sparsity, and offer a huge potential in developing next-generation digital twin technologies for aerospace applications.

42 ENGINEERING↗