SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ni-ion irradiated NiTi is nearly 50% harder, retains 85% recoverable deformation, and has reduced hysteresis. This work explores the feasibility of using ion beam modification to modulate the austenite to martensite phase transformation in NiTi, thereby achieving novel or localized properties in near-surface regions.
Ni-ion irradiated NiTi is nearly 50% harder, retains 85% recoverable deformation, and has reduced hysteresis. This work explores the feasibility of using ion beam modification to modulate the austenite to martensite phase transformation in NiTi, thereby achieving novel or localized properties in near-surface regions.
We report reconfigurable, mechanically responsive crystalline materials are central components in many sensing, soft robotic, and energy conversion and storage devices1,2,3,4. Crystalline materials can readily deform under various stimuli and the extent of recoverable deformation is highly dependent upon bond type1,2,5,6,7,8,9,10. Indeed, for structures held together via simple electrostatic interactions, minimal deformations are tolerated. By contrast, structures held together by molecular bonds can, in principle, sustain much larger deformations and more easily recover their original configurations. In this report we study the deformation properties of well-faceted colloidal crystals engineered with DNA. These crystals are large in size (greater than 100 µm) and have a body-centred cubic (bcc) structure with a high viscoelastic volume fraction (of more than 97%). Therefore, they can be compressed into irregular shapes with wrinkles and creases, and, notably, these deformed crystals, upon rehydration, assume their initial well-formed crystalline morphology and internal nanoscale order within seconds. For most crystals, such compression and deformation would lead to permanent, irreversible damage. The substantial structural changes to the colloidal crystals are accompanied by notable and reversible optical property changes. For example, whereas the original and structurally recovered crystals exhibit near-perfect (over 98%) broadband absorption in the ultraviolet–visible region, the deformed crystals exhibit significantly increased reflection (up to 50% of incident light at certain wavelengths), mainly because of increases in their refractive index and inhomogeneity.
Abstract Mechanical metamaterials inspired by the Japanese art of paper folding have gained considerable attention because of their potential to yield deployable and highly tunable assemblies. The inherent foldability of origami structures enlarges the material design space with remarkable properties such as auxeticity and high deformation recoverability and deployability, the latter being key in applications where spatial constraints are pivotal. This work integrates the results of the design, 3D direct laser writing fabrication, and in situ scanning electron microscopic mechanical characterization of microscale origami metamaterials, based on the multimodal assembly of Miura‐Ori tubes. The origami‐architected metamaterials, achieved by means of microfabrication, display remarkable mechanical properties: stiffness and Poisson’s ratio tunable anisotropy, large degree of shape recoverability, multistability, and even reversible auxeticity whereby the metamaterial switches Poisson’s ratio sign during deformation. The findings here reported underscore the scalable and multifunctional nature of origami designs, and pave the way toward harnessing the power of origami engineering at small scales.
Architected metamaterials such as foams and lattices exhibit a wide range of properties governed by microstructural instabilities and emerging phase transitions. Their macroscopic response–including energy dissipation during impact, large recoverable deformations, morphing between configurations, and auxetic behavior–remains difficult to capture with conventional continuum models, which often rely on discrete approaches that limit scalability. In this work, we propose a nonlocal continuum formulation that captures both stable and unstable responses of elastic architected metamaterials. The framework extends anisotropic hyperelasticity by introducing nonlocal variables and internal length scales reflective of microstructural features. Local polyconvex free-energy models are systematically augmented with two families of non-(poly)convex energies, enabling both metastable and bistable responses. Implementation in a finite element framework enables solution using a hybrid monolithic–staggered strategy. Simulations capture densification fronts, forward and reverse transitions, hysteresis loops, imperfection sensitivity, and globally coordinated auxetic modes. Overall, this framework provides a robust foundation for accelerated modeling of instability-driven phenomena in architected metamaterials, while enabling extensions to anisotropic, dissipative, and active systems as well as integration with data-driven and machine learning approaches.
Recently, the shape memory effect with significant recoverable shape deformation has been discovered in small volume single-crystal zirconia. The application potential for such shape memory ceramics has spurred in-depth exploration of the martensitic transformation crystallography and high temperature shape memory effect. In this paper, the martensitic transformation of micron-sized zirconia has been studied in both a pristine as-produced condition and after micromechanical compression, using synchrotron scanning micro X-ray diffraction (μXRD). The pristine zirconia was found to transform into the monoclinic phase via a different crystallographic path than the compressed zirconia, resulting in distinct monoclinic variant preferences. The characteristic martensitic transformation temperatures were also found to be higher after uniaxial compression than in the pristine condition. Such observations provide insight on the differences between stress-induced and thermally-induced martensitic transformation. Moreover, we have observed a full cycle of the shape memory effect with large recoverable strain (7%) in micron-sized zirconia at a temperature of 400 °C. Finally, our findings provide an important guideline to tailor the high-temperature shape memory properties of zirconia for further scientific research and engineering applications.
The influence of the microstructure on the visco-elastic properties of concrete is investigated using finite element simulations at the meso-scale. We first derive a constitutive law for the creep of the cement paste which accounts for both recoverable and permanent deformations, as well as the influence of temperature and internal relative humidity. The model is calibrated on a set of experiments at the cement paste scale, and then validated after upscaling to the concrete scale. The model is then applied to study the influence of the microstructure on the macroscopic creep of concrete. We show that materials with finer particles exhibit less creep, and that the anisotropy of creep can be explained with the shape and orientation of the aggregates. Furthermore, the acceleration of the stress relaxation in the presence of damage is explained by the micro-mechanical interaction between the aggregates, the cement paste, and the micro-cracks.
The additive manufacturing of shape memory alloys into complex geometries enables fabrication of advanced functional systems across a variety of fields and domains. This work presents results focused on the mechanical behavior of additively manufactured shape memory pseudoelastic NiTi. The deformation induced solid state phase transformation from austenite to martensite allows this system to accommodate large recoverable strains. This deformation behavior is fundamentally driven by crystal-scale transformation physics. Laser powder bed fusion processing reveals that the resulting microstructure, both grain morphology and crystallographic texture, is strongly dependent on the manufacturing processing history. Exhaustive mechanical testing demonstrates that these microstructural factors strongly impact both tensile and cyclic stress–strain behavior. Cyclic dissipative behavior, however, is similar across all tested microstructures following an initial transient period. Remarkably, analysis of spatial strain fields during tensile loading reveals two distinctly different localization “modes”. The first is initiation of localized deformation bands which continuously propagate through the tensile bar during loading. In the second mode localization is observed but lacks propagation; instead additional localization cites nucleate during subsequent loading. The latter phenomena is suspected to be driven by grain-scale deformation physics as the localized band morphologies coincide with grain morphologies. These phenomena strongly impact the resulting aggregate stress–strain behavior. Hence, manufacturers and designers of psuedoelastic functional components must at the very least consider the potential variability in properties when considering additive manufacturing processing. More ideally the process–structure–property relations can be used to further tailor and optimize final functional performance.
Inspired by the multiscale configuration of the microstructure of cork, the paper describes the design, 3D printing, and evaluation of a new type of multilayered cellular composite (MCC) structure composed of hard brittle and soft flexible phases. The mechanical behavior of 3D printed MCC structures have been investigated both experimentally and numerically. The experiments show that the MCC structure absorbs four times the amount of energy of a conventional cellular configuration under compressive strains up to 70%. Finite element simulations and 2D digital image correlation (DIC) also show that the multilayered architecture provides a more uniform strain distribution and higher stress transfer efficiency, with a resulting progressive failure mode rather than a catastrophic one. Cyclic loading tests demonstrate that the MCC structure also possesses exceptional shape recoverability under compressive deformations up to 40%. These remarkable performance characteristics result from synergies between the properties of the two constituent materials and the chosen multilayered cellular microstructure. The soft phase, in particular, plays a pivotal role in absorbing elastic energy during loading and then releasing the stored energy while unloading. The volume fraction of the soft phase is also essential to control energy absorption and the transition of failure modes. The deformation mechanisms demonstrated here are robust and applicable to other architected cellular materials across multiple length scales and suggest new ways to design lightweight and high-resilience structural materials.
The mechanisms responsible for deformation behavior in Nb/NiTi composite during pre-straining were investigated systematically using in-situ synchrotron X-ray diffraction, transmission electron microscopy and tensile test. It is shown that upon loading, the composite experiences elastic elongation and slight plastic deformation of B19', B2 and β-Nb phases, together with the forward stress-induced martensitic (SIM) transformation from B2 to B19'. Upon unloading, the deformation mechanisms of the composite mainly involve elastic recovery of B19', B2 and β-Nb phases, compression deformation of β-Nb phase and incomplete B19'→B2 reverse SIM transformation. In the tensile loading-unloading procedure, besides the inherent elastic deformation and SIM transformation, the (001) compound twins in B19' martensite can also be conducive to the elastic deformation occurring in B19'-phase of the composite. Therefore, this composite can exhibit a large recoverable strain after unloading owing to the elastic deformation, and the partially reversible and consecutive SIM transformation together with the (001) compound twins.
The low modulus β-type Ti alloys usually have peculiar deformation behaviors due to their low phase stability. However, the study of the underlying mechanisms is challenging since some physical mechanisms are fully reversible after the release of the load. In this paper, the deformation behavior of a low modulus β-type Ti36Nb5Zr alloy was investigated with the aid of in situ synchrotron X-ray diffraction (SXRD) during tensile loading. The evolution of lattice strains and relative integrated diffraction peak intensities of both the β and α” phases were analyzed to determine the characteristics of the potential deformation mechanisms. Upon loading, the α” diffraction spots appeared at specific azimuth angles of the two-dimensional SXRD patterns due to the <110> fiber texture of original β grains and the selection of favorable martensitic variants. The nonlinear deformation behavior originated from a reversible stress-induced martensitic transformation (SIMT). However, the SIMT contributed a little to the large recoverable strain of over 2.0%, which was dominated by the elastic deformation of the β phase. Various deformation mechanisms were activated successively at different applied strains, including elastic deformation, SIMT and plastic deformation. Our investigations provide in-depth understandings of the deformation mechanisms in β-type Ti alloys with low elastic modulus.
The maximum recoverable strain of most crystalline solids is less than 1% because plastic deformation or fracture usually occurs at a small strain. In this work, we show that a SrNi 2 P 2 micropillar exhibits pseudoelasticity with a large maximum recoverable strain of ~14% under uniaxial compression via unique reversible structural transformation, double lattice collapse–expansion that is repeatable under cyclic loading. Its high yield strength (~3.8 ± 0.5 GPa) and large maximum recoverable strain bring out the ultrahigh modulus of resilience (~146 ± 19 MJ/m 3 ), a few orders of magnitude higher than that of most engineering materials. The double lattice collapse–expansion mechanism shows stress–strain behaviors similar to that of conventional shape-memory alloys, such as hysteresis and thermo-mechanical actuation, even though the structural changes involved are completely different. Our work suggests that the discovery of a new class of high-performance ThCr 2 Si 2 -structured materials will open new research opportunities in the field of pseudoelasticity.
Here we report that to date the majority of published research on thermokarst has been directed at documenting its form, occurrence, and rates of occurrence. The fundamental processes driving thermokarst have long been largely understood. However, the detailed physical couplings between, water, air, soil, and the thermal dynamics governing freeze-thaw and soil mechanics is less understood and not captured in models aimed at predicting the response of frozen soils to warming and thaw. As computational resources increase more sophisticated mechanistic models can be applied; these show great promise as predictive tools. These models will be capable of simulating the response of soil deformation to thawing/freezing cycles and the long-term, non-recoverable response of the land surface to the loss of ice. At the same time, advances in remote sensing of permafrost environments also show promise in providing detailed and spatially extensive estimates in the rates and patterns of subsidence. These datasets provide key constraints to calibrate and evaluate the predictive power of mechanistic models. In conclusion, in the coming decade, these emerging technologies will greatly increase our ability to predict when, where, and how thermokarst will occur in a changing climate.
Meta-magnetic shape-memory alloys combine ferroelastic order with ferromagnetic order and exhibit attractive multifunctional properties, but they are extremely brittle, showing hardly any tensile deformability, which impedes their practical application. Here, for the first time, an Ni–Cu–Co–Mn–In microwire has been developed that simultaneously exhibits a magnetic field-induced first-order meta-magnetic phase transition and huge tensile superelasticity. A temperature-dependent in situ synchrotron high-energy X-ray diffraction investigation reveals that the martensite of this Ni 43.7 Cu 1.5 Co 5.1 Mn 36.7 In 13 microwire shows a monoclinic six-layered modulated structure and the austenite shows a cubic structure. This microwire exhibits an oligocrystalline structure with bamboo grains, which remarkably reduces the strain incompatibility during deformation and martensitic transformation. As a result, huge tensile superelasticity with a recoverable strain of 13% is achieved in the microwire. This huge tensile superelasticity is in agreement with our theoretical calculations based on the crystal structure and lattice correspondence of austenite and martensite and the crystallographic orientation of the grains. Owing to the large magnetization difference between austenite and martensite, a pronounced magnetic field-induced magnetostructural transition is achieved in the microwire, which could give rise to a variety of magnetically driven functional properties. For example, a large magnetocaloric effect with an isothermal entropy change of 12.7 J kg -1 K -1 (under 5 T) is obtained. The realization of magnetic-field- and tensile-stress-induced structural transformations in the microwire may pave the way for exploiting the multifunctional properties under the coupling of magnetic field and stress for applications in miniature multifunctional devices.
We report on the mechanical behavior of a solid Li-ion conductor, lithium phosphorous oxynitride (Lipon), for solid-state batteries. In particular, the purpose of this investigation was to quantify the resistance to cracking (fracture toughness) of this material by nanoindentation. We observed surprising ductility and the ability to recover in Lipon. We were unsuccessful in inducing cracks in Lipon and observed accommodation of stress via pile-up and densification rather than by cracking at various strain rates. Simulations demonstrate that both deformation and densification depend on the alkali content. Densification appears to be recoverable at room temperature. We discuss the findings in comparison with nanoindentation-induced cracking in other inorganic solid electrolyte materials and provide possible explanations for high resistance of Lipon to Li filament propagation.
In a previous disclosure, the use of 60- NiTiNOL, an ordered intermetallic compound composed of 60 weight percent nickel and 40 weight percent titanium, was investigated as a material for advanced aerospace bearings due to its unique combination of physical properties. Lessons learned during the development of applications for this material have led to the discovery that, with the addition of a ternary element, the resulting material can be thermally processed at a lower temperature to attain the same desirable hardness level as the original material. Processing at a lower temperature is beneficial, not only because it reduces processing costs from energy consumption, but because it also significantly reduces the possibility of quench cracking and thermal distortion, which have been problematic with the original material. A family of ternary substitutions has been identified, including Hf and Zr in various atomic percentages with varying concentrations of Ni and Ti. In the present innovation, a ternary intermetallic compound consisting of 57.6 weight percent Ni, 39.2 weight percent Ti, and 3.2 weight percent Hf (54Ni-45Ti-1Hf atomic percent) was prepared by casting. In this material, Hf substitutes for some of the Ti atoms in the material. In an alternate embodiment of the innovation, Zr, which is close in chemical behavior to Hf, is used as the substitutional element. With either substitution, the solvus temperature of the material is reduced, and lower temperatures can be used to obtain the necessary hardness values. The advantages of this innovation include the ability to solution-treat the material at a lower temperature and still achieve the required hardness for bearings (at least 50 Rockwell C) and superelastic behavior with recoverable strains greater than 2%. Most structural alloys will not return to their original shape after being deformed as little as 0.2% (a tenth of that possible with superelastic materials like 60 NiTiNOL). Because lower temperatures can be used in the heat treatment process, less energy will be consumed, and there will be less dimensional distortion and quench cracking. This results in fewer scrap parts, less material waste from large amounts of material removal, and fewer machining steps to rework parts that are out of specification. This material has a combination of properties that have been previously unobtainable. The material has a Young s modulus of approximately 95 GPa (about half that of conventional steels), moderate density (10 to 15% lower than conventional steels), excellent corrosion resistance, and high hardness (58 to 62 HRC). These properties make this material uniquely suited for advanced bearings.
Abstract Single-crystalline nickel-rich cathodes are a rising candidate with great potential for high-energy lithium-ion batteries due to their superior structural and chemical robustness in comparison with polycrystalline counterparts. Within the single-crystalline cathode materials, the lattice strain and defects have significant impacts on the intercalation chemistry and, therefore, play a key role in determining the macroscopic electrochemical performance. Guided by our predictive theoretical model, we have systematically evaluated the effectiveness of regaining lost capacity by modulating the lattice deformation via an energy-efficient thermal treatment at different chemical states. We demonstrate that the lattice structure recoverability is highly dependent on both the cathode composition and the state of charge, providing clues to relieving the fatigued cathode crystal for sustainable lithium-ion batteries.