Search NASA⌕ Search

SEARCH · Search NASA

Results for “recycling behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Analytical Ion Thruster Discharge Performance Model

A particle and energy balance model of the plasma discharge in magnetic ring-cusp ion thrusters has been developed. The model follows the original work of Brophy in the development of global 0-D discharge models that utilize conservation of particles into and out of the thruster and conservation of energy into the discharge and out of the plasma in the form of charged particles to the walls and beam and plasma radiation. The present model is significantly expanded over Brophy's original work by including self-consistent calculations of the internal neutral pressure, electron temperature, primary electron density, electrostatic ion confinement (due to the ring-cusp fields), plasma potential, discharge stability, and time dependent behavior during recycling. The model only requires information on the thruster geometry, ion optics performance and electrical inputs such as discharge voltage and currents, etc. to produce accurate performance curves of discharge loss versus mass utilization efficiency. The model has been benchmarked against the NEXIS Laboratory Model (LM) and Development Model (DM) thrusters, and successfully predicts the thruster discharge loss as a function of mass utilization efficiency for a variety of thrusters. The discharge performance model will be presented and results showing ion thruster performance and stability given.

discharge chambers↗
NASA NTRS1972

Investigative study of holographic recording materials development

The potential of certain cis-trans isomers and doped LiNbO3 for the holographic read/write/erase memory application was investigated. The cis-trans work involved the photochemical investigation of a number of potential materials as well as specific molecular engineering efforts on alpha-methyl stilbene and its derivatives. These efforts resulted in an increase in the change in index of refraction, and thereby, in potential recording utility, of an order of magnitude. The work on LiNbO3 was directed toward a preliminary investigation of the dynamics of the writing process. Several samples and a variety of writing conditions were investigated. An unexpected and as yet unexplained improvement in material behavior with continued recycling was observed. In addition, some effort was devoted to an analysis of the physical conditions under which several current theories of the optical damage process are valid.

Source record↗
NASA NTRS1993

Two newly discovered millisecond pulsars

Two millisecond pulsars have been discovered in the course of systematic surveys being made with the Arecibo radio telescope. PSR J2019 + 2425 has a 3.935 ms period and moves in a nearly circular, 76.5 day orbit around a about 0.3 solar mass companion. PSR J2322 + 2057, with a period of 4.808 ms, is an isolated object. The two pulsars have unusually small period derivatives, corresponding to spin-down time scales of 7.5 +/- 0.5 and 11 +/- 5 Gyr, respectively. Both objects show pulse time-of-arrival residuals no larger than a few microseconds over many months, lending further support to the observation that 'recycled' pulsars have extremely stable rotational behavior. The timing results also confirm that physics related to the rotational dynamics of these strongly self-gravitating stars - in particular, the value of the gravitational coupling constant G - remains essentially constant over time scales comparable to the Hubble time. Dispersion measures of the two pulsars indicate distances of 0.8-0.9 kpc.

Nice, D. J.↗
NASA NTRS1992

Venus tectonic styles and crustal differentiation

Two of the most important constraints are known from Pioneer Venus data: the lack of a system of spreading rises, indicating distributed deformation rather than plate tectonics; and the high gravity/topography ratio, indicating the absence of an asthenosphere. In addition, the high depth/diameter ratios of craters on Venus indicate that Venus probably has no more crust than Earth. The problems of the character of tectonics and crustal formation and recycling are closely coupled. Venus appears to lack a recycling mechanism as effective as subduction, but may also have a low rate of crustal differentiation because of a mantle convection pattern that is more distributed, less concentrated, than Earth's. Distributed convection, coupled with the nonlinear dependence of volcanism on heat flow, would lead to much less magmatism, despite only moderately less heat flow, compared to Earth. The plausible reason for this difference in convective style is the absence of water in the upper mantle of Venus. We have applied finite element modeling to problems of the interaction of mantle convection and crust on Venus. The main emphasis has been on the tectonic evolution of Ishtar Terra, as the consequence of convergent mantle flow. The early stage evolution is primarily mechanical, with crust being piled up on the down-stream side. Then the downflow migrates away from the center. In the later stages, after more than 100 m.y., thermal effects develop due to the insulating influence of the thickened crust. An important feature of this modeling is the entrainment of some crustal material in downflows. An important general theme in both convergent and divergent flows is that of mixing vs. stratification. Models of multicomponent solid-state flow obtain that lower-density crustal material can be entrained and recycled, provided that the ration of low-density to high-density material is small enough (as in subducted slabs on Earth). The same considerations should apply in upflows; a small percent of partial melt may be carried along with its matrix and never escape to the surface. Models that assume melt automatically rising to the crust and no entrainment or other mechanism of recycling lower-density material obtain oscillatory behavior, because it takes a long time for heat to build up enough to overcome a Mg-rich low-density residuum. However, these models develop much thicker crust than consistent with estimates from crater depth/diameter ratios.

Kaula, W. M.↗
NASA NTRS1992

Diagnostics of disk-magnetosphere interaction in neutron star binaries

The interaction between the magnetospheres of accreting neutron stars and accretion disks plays at key role in determining the properties of many accretion-powered neutron star X-ray sources and the recycled binary and millisecond rotation-powered pulsars. Here we show that the behavior of the horizontal branch quasi-periodic intensity oscillations in low mass X-ray binaries and the correlation between the magnetic fields and periods of binary and millisecond pulsars are sensitive probes of the state of the inner disk.

Ghosh, Pranab↗
NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer-by-layer. Alloy 718 powder feedstocks for selective laser melting (SLM) additive manufacturing are produced commercially by both gas and rotary atomization and are available typically in the 10-45 or 15-45 microns size ranges. A comprehensive investigation was conducted to understand the impact of powder variability on the microstructure and mechanical behavior of SLM 718 heat treated to Aerospace Material Specification (AMS) 5664. This study included sixteen virgin powders and three once-recycled powders within the 10-45 and 15-45 microns size ranges that were obtained from seven direct source suppliers and one reseller. Although alike as highly regular spheroids, these powders showed distinct differences in composition (especially Al, C and N contents), particle size distributions, and powder features such as degree of agglomeration, fusion and surface roughness. Compositional differences expectedly had the strongest impact on microstructure. High N and C contents formed TiN-nitrides and/or (Nb,Ti,Mo)-C carbides on the grain boundaries, prevented recrystallization during heat treatment, and resulted in retained (001)-scalloped shaped grains that ranged from 19 to 41 microns in average size. In the absence of this particle pinning, the average grain size of the heat treated SLM 718 ranged from 51 microns to 90 microns. Room temperature tensile and high cycle fatigue (HCF) testing compared as-fabricated (AF) and low stress ground (LSG) surface conditions. Tensile testing revealed consistent behavior between the two surface conditions and amongst the powder lots. The finer grained SLM 718 builds displayed the lowest tensile properties. A SLM 718 build fabricated from a powder with eight times lower C content showed statistically better tensile properties presumably due to enhanced coarsening of (delta)-Ni3Nb precipitates. The specimens from once-recycled powders had slightly higher tensile strengths and slightly higher ductility compared to their virgin equivalents; once-recycling also did not substantially degrade the mean HCF life. The LSG fatigue lives agreed with conventionally manufactured 718 data, while AF lives exhibited a knock-down due to surface roughness. The fatigue lives of AF specimens were statistically equivalent across powder lots except for one and failures typically initiated at stress concentrators associated with SLM surface asperities. Fatigue testing of low stress ground specimens result in both transgranular and within facet crack initiations. More than half of the cracks initiated from these facets for the machined condition; however, these facets appeared to be within grains that were larger-than-average in size. A nitrogen-atomized powder with fine prior particles of TiN-nitrides and M(Ti,Nb,Mo)C carbides from atomization on powder surfaces resulted in the best fatigue performance with segregation of these particles to the SLM 718 grain boundaries leading to higher resistance to early-stage crack propagation. Typically the fine-grained builds with minor phases along the grain boundaries did not perform well in fatigue, whereas a larger-grain build with lower carbon content and coarser delta-Ni3Nb precipitates showed the next best HCF response. Further details of the build microstructure and its impact on tensile and fatigue behavior was considered.

laser deposition↗
NASA NTRS2016

NiTi Alloys for Tribological Applications: The Role of In-Situ Nanotechnology

Beginning in 2004, NASA initiated the investigation and development of, Nitinol 60, a nickel-rich and dimensionally stable version of shape memory alloy Nitinol 55, as an alternative to bearing steel. Early investigations showed it to be hard and impervious to aqueous corrosion but the fundamental reasons for these properties were unknown. Shape memory alloys made from equiatomic Ni-Ti are widely known for their unique dimensional instability behavior that can be triggered by thermal and mechanical stress. The nickel-rich alloys exhibit no such dimension change property and have high hardness but have largely been overlooked by industry and the engineering community. Though steel is the dominant material of choice for mechanical components (bearings and gears) it has intrinsic limitations related to corrosion and plastic deformation. In contrast, Ni-Ti alloys are intrinsically rustproof and can withstand high contact loads without damage (denting). Over the last decade, focused RD to exploit these alloys for new applications has revealed that in-situ nano-scale phases that form during processing are largely responsible for NiTis remarkable properties. In this presentation, the state-of-art of nickel-rich NiTi alloys will be introduced and the nanotechnology behind their intriguing behavior will be addressed. The presentation will include discussion of how NASA is adopting this new technology inside the space station water recycling system as a pathfinder for more down-to-earth tribological challenges.

metals↗
NASA NTRS2004

Lunar and Planetary Science XXXV: Io, with a Dash of Titan

The session "Io, with a Dash of Titan" contained the following reports:A Deep Lava Channel on Io ; Volcanic Activity at Tvashtar Catena, Io; Characterization of Activity at Loki from Galileo and Ground-based Observations; Active and Passive Lava Resurfacing Processes on Io: A Comparative Study of Loki Patera and Prometheus; Loki Patera as the Surface of a Magma Sea; Lava Lakes on Io: New Perspectives from Modeling; Global Distribution of Active Volcanism on Io as Known at the End of the Galileo Mission Relationships Between Paterae, Mountains, and Hotspots on Io from a Global Database; Lithospheric Recycling on Io: The Role of Delamination; Building Mountains on Io: Implications for Io s Lithosphere ; The Effect of Large Melt Fraction on the Deformation Behavior of Peridotite: Implications for the Rheology of Io s Mantle; Matching Various Observations of Io with DSMC Modeling: Plume, Plume Shadow, Sodium Field Around Pele; and How Does Titan Retain a Finite Orbital Eccentricity?

Source record↗
NASA NTRSDate not supplied

Numerical analysis of Microgravity Bubble Separation in Open Channels with ISS Bemchmarks

Spacecraft fluid systems often require specific considerations to operate in a manner similar to those on Earth. For instance, an open wedge shaped channel can serve as a pathway for passively separating bubbles from a liquid in a two phase flow, analogous to buoyancy effects on Earth. As the bubbles merge within the channel, they become increasingly confined in the wedge, driving them upwards and outwards toward the free surface due to capillary forces. These same forces ensure coalescence and allow the bubbles to escape through the free surface. However, in low gravity environments, a challenge arises when bubbles are not sufficiently large. Under such conditions, the bubbles tend to follow trajectories near their inscribed elevations, never fully leaving the liquid. Such unseparated bubbles can lead to downstream pump failure, cavitation, flow instabilities, dryout, and other adverse effects aboard spacecraft. Understanding and exploiting the underlying mechanisms behind this behavior is crucial for enhancing the reliability of passive capillary fluids management in space applications, including cryogenic and storable fuels transport, thermal fluids circulation, water recycling for life support, plant watering systems, and more. The joint German Aerospace Center (DLR) and NASA Capillary Channel Flow (CCF) experiment conducted on the International Space Station has provided an extensive publicly available database documenting such phenomena (https://science.nasa.gov/physical sciences informatics psi). Leveraging this resource, we aim to establish benchmarks for our numerical investigation of zero gravity bubbly two phase flow in open wedge channels. Specifically, we seek to quantitatively understand the mechanisms governing ‘inscribed’ bubble motion, considering the apparent interplay of two competing forces: Saffman lift (causing upward/outward motion) and the Magnus effect (causing downward/inward motion). Our cross cutting findings directly inform the development of robust passive phase separation methods within spacecraft plumbing systems.

bubble↗
NASA NTRS2005

Mechanical and Structural Behavior of Granular Material Packed Beds for Space Life Support System Applications

Long-term human mission to space, such as living in International Space Station (ISS), Lunar, and Martian bases, and travel to Mars, must m ake use of Advanced Life Support Systems (ALSS) to generate and recycle critical life supporting elements like oxygen and water. Oxygen Gen eration Assembly (OGA) and Water Processor Assembly (WPA), critical c omponents of ALSS, make use of series of granular material packed beds for generation and recycling of oxygen and water. Several granular m aterials can be used for generation, recycling, processing and recovery of oxygen and water. For example, they may include soft bed media, e.g. ion exchange resins for oxygen generation assembly and hard bed media such as, activated alumina, magchem (Magnesium oxide) and activa ted carbon to remove organic species like ethanol, methanol, and urea from wastewater in Water recovery/processing assembly. These beds are generally packed using a plate-spring mechanism to provide sufficien t compaction to the bed media throughout the course of operation. This paper presents results from an experimental study of a full-scale, 3 8.1 cm (15 inches) long and 3.7 cm (1.44 inches) diameter. activated alumina bed enclosed in a cylinder determining its force-displacement behavior, friction mobilizing force, and axial normal stress distribu tion under various axially applied loads and at different levels of packing. It is observed that force-displacement behavior is non-linear for low compaction level and becomes linear with increase in compaction of the bed media. Axial normal stress distribution along the length of the bed media decreased non-linearly with increase in depth from the loading end of the granular media. This paper also presents experimental results on the amount of particulates generated corresponding to various compaction levels. Particulates generated from each of the tests were measured using standard US sieves. It was found that the p articulates and the overall displacement of the bed media increased with decrease in initial compaction of the bed media. This effect could be attributed to the greater tendency for inter-particle sliding/rub bing due to smaller internal friction angles, as seen from the shear tests, at lesser initial compacted levels. Upon unloading, it was obse rved that there was no change in displacement (especially rebounding) in the bed media. This effect could be attributed to the fact that th e porous activated alumina particles fracture/break upon increase in applied load (during loading phase) and occupy void spaces in between the material grains; thereby leading to settling of the media. The lo ad-displacement curve becomes more linear with increase in initial compaction of the bed media. It is concluded that compaction considerabl y affects the load-displacement behavior of the bed media. A series of tests were also conducted on the packed bed media to determine the f orce required to mobilize the friction between the bed media and the housing cylinder. The results from these tests showed the existence of significant friction between the bed media and the encasing stainles s steel cylinder. Further, it was found that friction effects were more pronounced for media with higher initial compaction. Internal frict ion of the granular media was measured using direct shear apparatus. It was observed that the internal friction increased with increase in initial compaction of the bed media. In this study, a computational m odel (CM) is also developed using finite element software ANSYS to verify experimental results obtained for the distribution of the axial n ormal stress and axial displacement along the length of the full-scal e activated alumina bed media. In the computational model, the granular material is considered to have appropriate failure and frictional c ontact exists between the wall and the granular media. It is observed that the model predicts results closely with the experimental method. The compational results show that the axial normal stress distribution along the length of the activated alumina media decreases non-linea rly from the loading end and is negligible beyond a certain depth. Th is can be attributed to the existence of friction between the walls and the media and that the friction takes up most of the applied load.

Malla, Ramesh B.↗
NASA NTRS2019

A New Recycling Method to Generate Turbulent Inflow Profiles

The accuracy of the scale-resolving simulations for practical geometries strongly depends on the inflow boundary conditions. Imposing experimentally observed turbulent inflow profiles for the numerical simulations is a major challenge. Existing methods available in the literature assume self-similar behavior, which is not true for most of the experiments. In the present work, we formulate the turbulent inflow profile generation technique as an optimization problem. An adjoint technique is exploited to evaluate the sensitivities of multiple input parameters for the present problem. The present formulation is then tested to generate a laminar boundary layer profile, turbulent boundary layer profile, and turbulent jet profile.

Garai, Anirban↗
NASA NTRS2000

Detection of Extraterrestrial Ecology (Exoecology)

Researchers in the Astrobiology Technology Branch at Ames Research Center have begun investigating alternate concepts for the detection of extraterrestrial life. We suggest searching for extraterrestrial ecology, exoecology, as well as for extraterrestrial biology, exobiology. Ecology describes the interactions of living things with their environment. All ecosystems are highly constrained by their environment and are constrained by well-known system design principles. Ecology could exist wherever there is an energy source and living I things have discovered some means to capture, store, and use the available energy. Terrestrial ecosystems use as energy sources, light, organic molecules, and in thermal vents and elsewhere, simple inorganic molecules. Ecosystem behavior is controlled by matter and energy conservation laws and can be described by linear and nonlinear dynamic systems theory. Typically in an ecosystem different molecules are not in chemical equilibrium and scarce material is conserved, stored, or recycled. Temporal cycles and spatial variations are often observed. These and other -eneral principles of exoecology can help guide the search for extraterrestrial life. The chemical structure observed in terrestrial biology may be highly contingent on evolutionary accidents. Oxygen was not always abundant on Earth. Primitive sulfur bacteria use hydrogen sulfide and sulfur to perform photosynthesis instead of water and oxygen. Astrobiologists have assumed, for the sake of narrowing and focusing our life detection strategies, that extraterrestrial life will have detailed chemical similarities with terrestrial life. Such assumptions appear very reasonable and they allow us to design specific and highly sensitive life detection experiments. But the fewer assumptions we make, the less chance we have of being entirely wrong The best strategy for the detection of extraterrestrial life could be a mixed strategy. We should use detailed assumptions based on terrestrial biology to guide some but not all future searches for alien life. The systems principles of exoecology seem much more fundamental and inescapable than the terrestrial biology analogies of exobiology. We should search for exoecology as well as exobiology.

Jones, Harry↗
NASA NTRS2012

The Role of Lightning in Controlling Interannual Variability of Tropical Tropospheric Ozone and OH and its Implications for Climate

Nitrogen oxides (NO(x) = NO + NO2) produced by lightning make a major contribution to the production of the dominant tropospheric oxidants (OH and ozone). These oxidants control the lifetime of many trace gases including long-lived greenhouse gases, and control the source-receptor relationship of inter-hemispheric pollutant transport. Lightning is affected by meteorological variability, and therefore represents a potentially important tropospheric chemistry-climate feedback. Understanding how interannual variability (IAV) in lightning affects IAV in ozone and OH in the recent past is important if we are to predict how oxidant levels may change in a future warmer climate. However, lightning parameterizations for chemical transport models (CTMs) show low skill in reproducing even climatological distributions of flash rates from the Lightning Imaging Sensor (LIS) and the Optical Transient Detector (OTD) satellite instruments. We present an optimized regional scaling algorithm for CTMs that enables sufficient sampling of spatiotemporally sparse satellite lightning data from LIS to constrain the spatial, seasonal, and interannual variability of tropical lightning. We construct a monthly time series of lightning flash rates for 1998-2010 and 35degS-35degN, and find a correlation of IAV in total tropical lightning with El Nino. We use the IAV-constraint to drive a 9-year hindcast (1998-2006) of the GEOS-Chem 3D chemical transport model, and find the increased IAV in LNO(x) drives increased IAV in ozone and OH, improving the model fs ability to simulate both. Although lightning contributes more than any other emission source to IAV in ozone, we find ozone more sensitive to meteorology, particularly convective transport. However, we find IAV in OH to be highly sensitive to lightning NO(x), and the constraint improves the ability of the model to capture the temporal behavior of OH anomalies inferred from observations of methyl chloroform and other gases. The sensitivity of OH is explained using photochemical reaction rates which show a "magnification" effect of the initial lightning NO perturbation on OH primary production, HO(x) recycling, and OH loss frequencies. This influence on OH may represent a negative feedback, if lightning increases in a warming world..

Murray, Lee T.↗
NASA NTRS2012

Design and Manufacturing Considerations for Shockproof and Corrosion-Immune Superelastic Nickel-Titanium Bearings for a Space Station Application

An intermetallic nickel-titanium alloy, 60NiTi (60wt%Ni, 40wt%Ti), is a promising tribological material for space mechanisms. 60NiTi offers a broad combination of physical properties that make it unique among bearing materials. 60NiTi is hard, electrically conductive, highly corrosion resistant, readily machined prior to final heat treatment, easily lubricated and is non-magnetic. It also falls within the class of superelastic alloys and can elastically endure large strains (beyond 5 percent) making it highly resistant to excessive and unexpected (shock) loads. Key material properties and characteristics such as elastic modulus, tensile fracture sensitivity and residual stress behavior, however, differ from conventional alloys such as steel and this significantly affects bearing design and manufacturing. In this paper, the preliminary design and manufacture of ball bearings made from 60NiTi are considered for a highly corrosive, lightly loaded, low speed bearing application found inside the International Space Station s water recycling system. The information presented is expected to help guide more widespread commercialization of this new technology into space mechanism and other applications.

DellaCorte, Christopher↗
NASA NTRS1988

Nd isotopes and crustal growth rate

Sm/Nd isotopic constraints on crustal growth is discussed. In order to constrain Sm/Nd fractionation between continental crust and depleted mantle, an extensive data base of isotopic measurements (assumed to be adequately representative of continental crust) was compiled. The results imply that the evolution of depleted mantles was roughly linear, with no major discontinuities over the course of geologic time. This is different from other determinations of depleting mantle evolution, which show nonlinear behavior. The Sm/Nd evolution lines for continental crust and depleted mantle intersect between 3.8 to 4.0 Ga, which may indicate that the onset of continental growth was later than 4.5 Ga. A mathematical model is described, the results of which imply that time integrated crustal additions from the mantle are about 1.8 to 2.5 cu km/a, whereas crustal subtractions by sediment recycling are about 0.6 to 1.5 cu km/a. This results in a net time integrated crustal growth rate of about 1 cu km/a, which is similar to present day rates determined, for example, by Reymer and Schubert.

Albarede, F.↗
NASA NTRSDate not supplied

Characterizing Electrical Arc Behavior in Ion Engines

Gridded ion engines represent a class of electric thrusters characterized by high propulsive efficiency and high total impulse capabilities. These engines operate by applying high voltage to multi-aperture electrodes, thereby electrostatically accelerating plasma to generate thrust. Within the course of normal operations, periodic occurrences of high voltage breakdowns manifest within the thruster. These breakdowns constitute an inherent aspect of operation, with observations indicating a diminishing frequency and total count over the thruster's operational lifespan. To safeguard the propulsion system during such occurrences, the power processing unit (PPU) employs an automated arc extinction sequence, termed "recycle," which is triggered upon detection of an over-current condition. The initial phase of this sequence involves momentarily deactivating the high voltage and reducing the discharge current to a predetermined level, minimizing plasma impingement as the ion beam is defocused. The high voltage is subsequently reapplied, and the discharge current is returned to its nominal value. The entire sequence typically spans approximately 800 milliseconds. Throughout a recycle event, the propulsion system experiences various current and voltage transients as the arc current traverses the system and different power supplies are toggled on and off.

electric propulsion↗
NASA NTRS1977

A model for eruption behavior of a volcanic vent in eastern Mare Serenitatis

The origin is considered of droplets of ultramafic composition which are present in all soils collected from the mare surface at the Apollo 17 landing site. The droplets consist of homogeneous orange glass or their partially crystallized equivalent, the black droplets. These clastic deposits have a mean grain size of 40 micrometers. The droplet formation ages range from 3.5 to 3.83 b.y. It has been proposed that the droplets formed as a spray of low viscosity melt during lava fountaining. Based upon the thermal history as determined by studying olivine and particle shapes, two models for the formation of the sequence of droplets represented by samples 74001 and 74220 are presented. Both models assume, as proposed by Heiken et al. (1974), that the droplets were formed as a spray from a lava fountain and the compound forms were evidence for 'recycling' of solid, cooler droplets back into the fountain, encountering molten droplets before being deposited.

Heiken, G.↗
NASA NTRSDate not supplied

Medical System Requirements Development for Lunar Operations

The major health hazards of spaceflight include higher levels of damaging radiation, altered gravity, extended periods of isolation and confinement, a closed and potentially hostile living environment, and the stress associated with being a long distance from Earth. As we increase the duration of lunar stays with foreseeable communication latencies and disruptions, there will be a progressive need for crew to maintain their own health and independently respond to critical medical events. The Exploration Medical Capability element of the NASA Human Research Program is developing a set of Medical System requirements for lunar transit and surface operations. These requirements specify the capabilities, processes and procedures of a habitat Medical System needed for a range of conditions known to occur during spaceflight. Requirement text is written so as not to constrain innovative design solutions necessary for a resilient system. The requirement set includes attributes and functions the Medical System imposes on eight additional habitat systems. A key property of the Medical System is the provision of medical knowledge that will be stored, updated, analyzed, and secured within a Habitat Data System. A Task Performance Support System will aid in medical data acquisition and interpretation, crew training, medical condition prevention, diagnosis and treatment, provide interactive procedures, and track medical inventory. A Wellness System will focus on the provision of countermeasures to prevent, mitigate or treat adverse physical and behavioral health effects while the Medical System recommends adjustments to these countermeasures to maintain crew health. An Environmental Monitoring System will share out-of-bounds readings of air and water quality, acoustics, and radiation exposure levels with the Medical System to help identify issues before they affect crew health and performance. A Communications System will provide secured and private consultations between crew and the ground medical team and their loved ones on Earth. The Medical System also imposes requirements on a Research & Testbed System, fostering advanced medical science such as human research. A Waste Management System provides biohazard waste containment and waste disposal options (recycle and reuse). An Extravehicular Activity System supports crew health during lunar surface activities. And finally, a Maintenance Support System ensures that medical equipment is performing as expected. These requirements are being specifically developed for lunar surface operations but could help to identify Medical System requirements for any space habitat (e.g., I-Hab, commercial endeavors, etc.).

technology↗