Search NASA⌕ Search

SEARCH · Search NASA

Results for “reduction of thermo-mechanical stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A Double-side Cooled SiC MOSFET Power Module with Sintered-silver Interposers: I. Design, Simulation, Fabrication, and Performance Characterization

Planar, double-side cooled power modules are emerging in electric-drive inverters because of their low profile, better heat extraction, and lower package parasitic inductances. However, there is still concern about their reliability due to the rigid interconnection between the device chips and two substrates of the power module. In this paper, a porous interposer made of low-temperature sintered silver is introduced to reduce the thermo-mechanical stresses in the module. A double-side cooled half-bridge module consisting of two 1200 V, 149 A SiC MOSFETs was designed, fabricated, and characterized. By using the sintered-Ag instead of solid copper interposers, our simulation results showed that at a total power loss of 200 W, the thermo-mechanical stress at the most vulnerable interfaces (interposer-attach layer) was reduced by 42 % and in the SiC MOSFET by 50 % with a trade-off of only 3.6 % increase in junction temperature. The sintered-Ag interposers were readily fabricated into desired dimensions without post-machining and did not require any surface finishing for die-bonding and substrate interconnection by silver sintering. Here, the porous interposers were also deformable under a low force or pressure, which helped to accommodate chip thickness and/or substrate-to-substrate gap variations in the planar module structure, thus simplifying module fabrication. Experimental results on the electrical performance of the fabricated SiC modules validated the success of using the porous silver interposers for fabricating planar, double-side cooled power modules.

42 ENGINEERING↗
DOE OSTI2021

Analysis and Optimization of a Multi-Layer Integrated Organic Substrate for High Current GaN HEMT-Based Power Module

In this paper, analysis and optimization of a multi-layer organic substrate for high current GaN HEMT based power module are discussed. The organic multi-layer substrates can provide high electrical performance in terms of low parasitic inductance in the power loop by providing vertical layout, and shielding for reduction of common-mode noise, a common problem in fast switching power converters. Furthermore, high performance cooling solutions, such as micro-channel heat sinks, can be directly bonded to the substrate for optimum thermal management. The structure of the proposed architecture, thermal analysis and optimization of layer thickness, thermo-mechanical stress analysis of the GaN HEMT and development of a high-performance heat sink are discussed.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

FY25 Theory and Simulation Performance Target: Development of an integrated modeling framework for fusion reactor design and assessment (Final Report)

This report documents the FY25 Theory and Simulation Performance Target (TSPT) of developing an integrated modeling framework for fusion reactor design and assessment (FREDA). Over Q1-Q4, new capabilities were developed across both plasma and engineering domains and demonstrated on an example representation of a Compact Advanced Tokamak with a Dual Cooled Lead Lithium blanket. This represents a first-of-a-kind demonstration of coupled core-to-wall-to-engineering for a reactor. Self-consistent CESOL workflows were applied to provide core, pedestal, and SOL prediction; new modules were developed for energetic particle stability (FAR3D) and transport (TGLF-EP) analysis; and boundary plasma modeling (SOLPS-ITER, BOUT++/Hermes-3) was expanded to evaluate wall and divertor heat fluxes and interface with engineering thermal analysis. A parameterized CAD tool, TRACER, was expanded to generate medium-fidelity divertor, blanket, and coil geometries; OpenFOAM and Diablo workflows were applied for first-wall and divertor thermal analyses with helium cooling; and reduced-order models were created for high-mass-flux divertor cooling. Magnet multiphysics capabilities were verified between Elmer, Diablo, and a new MFEM-based solver, and workflows enable stress, thermal, and neutron-fluence analysis of TF coils with neutronics-driven heating. Nuclear and blanket analysis workflows were demonstrated, including tritium breeding, transport, and CFD-informed thermo-mechanical assessment. Preliminary multi-fidelity uncertainty quantification workflows were applied to boundary modeling codes and shown to achieve variance reductions with fewer high-fidelity boundary simulations. Key findings highlight the challenges of resolving the ITEP gap to find suitable balance between wall and divertor loads, neutron heating, and practical limits of PFC cooling. Next step priorities are to develop automated workflows to check boundary code convergence and detachment, implement tighter physics-engineering CAD provenance tracking, and inclusion of plasma-material interface models for SLAG and tungsten cracking behavior. Collectively, these developments establish sophisticated capabilities for predictive, multi-fidelity, whole-device modeling that integrates plasma physics, materials, magnets, and nuclear engineering to guide pathways to viable Fusion Pilot Plant design points.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Packaging Development for a 1200V SiC BiDFET Switch Using Highly Thermally Conductive Organic Epoxy Laminate

A novel 1.2 kV/10A, 4H-SiC monolithic, bidirectional switch has been developed for use in cycloconverter applications to facilitate high-frequency direct AC-to-AC power conversion and enables new power converter topologies. A new packaging solution, utilizing a 100 µm flexible polyimide organic laminate substrate is developed to mitigate thermo-mechanical stress during power cycling and enable smaller form factor and lower cost. Multiphysics simulations and static tests were conducted to show performance characterization of the module and compare it against metallic substrates. A new organic laminate epoxy resin composite dielectric (ERCD) is also evaluated for superior thermal performance and shows 63% reduction in junction to case resistance compared to DBC substrates.

Silicon Carbide, Bi-directional switch, BiDFET, MO↗
DOE OSTI2024

Chloride-Induced Stress Corrosion Cracking of Friction Stir-Welded 304L Stainless Steel: Effect of Microstructure and Temperature

Dry storage canisters of used nuclear fuels are fabricated using SUS 304L stainless steel. Chloride-induced stress corrosion cracking (CISCC) is one of the major failure modes of dry storage canisters. The cracked canisters can be repaired by friction stir welding (FSW), a low-heat input ‘solid-phase’ welding process. It is important to evaluate the ClSCC resistance of the friction stir welded material. Stress corrosion cracking (SCC) studies were carried out on mill-annealed base materials and friction stir welded 304L stainless U-bend specimens in 3.5% NaCl + 5 N H2SO4 solution at room temperature and boiling MgCl2 solution at 155 °C. The engineering stress on the outer fiber of the FSW U-bend specimen was ~60% higher than that of the base metal (BM). In spite of the higher stress level of the FSW, both materials (FSW and BM) showed almost similar SCC failure times in the two different test solutions. The SCC occurred in the thermo-mechanically affected zone (TMAZ) of the FSW specimens in the 3.5% NaCl + 5 N H2SO4 solution at room temperature, while the stirred zone (SZ) was relatively crack-free. The failure occurred at the stirred zone when tested in the boiling MgCl2 solution. Hydrogen reduction was the cathodic reaction in the boiling MgCl2 solution, which promoted hydrogen-assisted cracking of the heavily deformed stirred zone. The emergence of the slip step followed by passive film rupture and dissolution of the slip step could be the SCC events in the 3.5% NaCl + 5 N H2SO4 solution at room temperature. However, the slip step height was not sufficient to cause passivity breakdown in the fine-grained SZ. Therefore, the SCC occurred in the partially recrystallized softer TMAZ. Overall, the friction-stirred 304L showed higher tolerance to ClSCC than the 304L base metal.

304L austenitic stainless steel↗
DOE OSTI2020

Tuning martensitic transformations via coherent second phases in nanolaminates using free energy landscape engineering

In this work we explore the possibilities and limitations of using a coherent second phase to engineer the thermo-mechanical properties of a martensitic alloy by modifying the underlying free energy landscape that controls the transformation. We use molecular dynamics simulations of a model atomistic system where the properties of a coherent, nanoscale second phase can be varied systematically. With a base martensitic material that undergoes a temperature-induced transformation from a cubic austenite to a monoclinic martensite, simulations show significant ability to engineer the transformation temperatures, from a ~50% reduction to a ~200% increase, with 50 at.% of the cubic second phase. We establish correlations between the properties of the second phase, the transformation characteristics, and the microstructure via the free energy landscape of the twophase systems. Coherency stresses have a strong influence on the martensitic variants observed and can even cause the non-martensitic second phase to undergo a transformation. Reducing the stiffness of the second phase increases the transformation strain and modifies the martensitic microstructure, increasing the volume fraction of the transformed material. This increase in transformation strain is accompanied by a significant increase in Af and thermal hysteresis, while Ms remains unaltered. Our findings on the tunability of martensitic transformations can be used for informed searches of second phases to achieve desired material properties, such as achieving room temperature, lightweight shape memory alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of Zn and Ca on the deformation texture evolution of Mg–Zn–Ca alloys at elevated temperatures

This work utilized crystal plasticity simulations and experimental thermo-mechanical processing to examine how Zn and Ca content affects texture evolution in Mg–Zn–Ca alloys during simulated hot rolling. Four different compositions were studied: unalloyed Mg and three Mg alloys of ZX0p50 (Mg- 0.5 wt% Zn- 0.1 wt% Ca), ZX30 (Mg-3 wt% Zn- 0.1 wt% Ca), and ZX31 (Mg-3 wt% Zn- 0.3 wt% Ca). Multi-pass Gleeble experiments simulated hot rolling using plane strain conditions. Unalloyed Mg developed a strong basal texture, while the addition of Zn and Ca significantly weakened the texture in ZX30 and ZX31; this reduction was not seen in ZX0p50. Notably, ZX31 exhibited a split basal texture aligned with the rolling direction. Crystal plasticity simulations revealed that the weaker basal texture in ZX30 and ZX31 resulted from reduced activation of basal and twinning modes compared to unalloyed Mg and Zx0p50. Increased Zn and Ca content raised the ratios of basal to pyramidal critical resolved sheer stress (CRSS) and twin to pyramidal CRSS, enhancing pyramidal slip activity and weakening the basal texture. Extension twinning played a critical role in texture development during the first deformation pass. In unalloyed Mg and ZX0p50, twinning led to a strong basal texture, while ZX30 and ZX31 had weak basal textures that increased only slightly with further deformation. The split basal poles simulated in ZX31 were consistent with the experimental findings, highlighting the interplay between alloy composition and texture evolution.

Crystal plasticity finite element↗
DOE OSTI2022

Steady state thermo-mechanics and material property definition framework for analyzing DCLL blanket in the fusion nuclear science facility

In this work, a thermo-mechanics model that relies on creating the material property definition framework (MPDF) and multiphysics coupling of the heat transfer and the solid mechanics modules is developed to determine the structural integrity of the recently designed dual cooled lead lithium (DCLL) inboard blanket (IB) for the Fusion Nuclear Science Facility under steady state loads. The MPDF is called to supply fusion relevant neutron irradiation and temperature induced changes in material properties during multiphysics finite element runs, and PbLi temperature profiles are used to approximate Magnetohydrodynamics effect and the nuclear volumetric heating on the PbLi. Neutron irradiation and temperature induced reduction of the yield and ultimate strengths of F82H steel at the first wall (FW) are quantified for one year. A blanket in an assembly with gaps between blanket sectors and another blanket in an assembly with no gaps between blanket sectors, both exposed to radiation damage that lasted for one year are analyzed. Analysis using the elastic ITER structural design criteria for in-vessel components (ITER SDC-IC) design rules and a linear isotropic-hardening-type elastoplastic material model are used where most appropriate. The IB blanket with gaps between blanket sectors will withstand the steady state combined thermal and coolant loads for one year operational period but will fail if no gaps are allowed between blanket sectors. It is recommended that a gap of about 7.62 mm should be provided between IB blanket sectors during assembly which would close up during service, stop neutron streaming, reduce stresses and reduce bending of the FW into the scrape-off layer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Dynamic flow stress of pure polycrystalline aluminum: Pressure-shear plate impact experiments and extension of dislocation-based modeling to large strains

The dynamic thermo-mechanical behavior of pure aluminum has attracted renewed interest lately due to experimental observations of an anomalous increase in Hugoniot Elastic Limit (HEL) at incipient plasticity and elevated temperatures in polycrystalline pure metals. In context of current dislocation-mediated plasticity models for metals, this increase in dynamic strength is indicative of a transition in the rate controlling mechanism for dislocation glide from being thermally assisted to phonon-drag restricted due to increase in phonon viscosity at elevated temperatures. Though these studies have helped to shed light on these important mechanisms operative in FCC metals at incipient plasticity, the extent to which they contribute to flow stress, particularly at larger strains, remains unclear. Here, we address these questions through a combined experimental and modeling effort focused on investigating the evolution of dynamic flow stress in polycrystalline aluminum using experimental data gathered from a series of combined pressure-and-shear plate impact (PSPI) experiments designed to reveal the flow stress of pure aluminum at strain rates ~ 10 5 /s, plastic strains of up to 40% and temperatures ranging from room to 866 K. In all cases, the flow stress of aluminum, as inferred from the measured transverse particle velocity histories at the free surface of an elastic tungsten carbide target plate, reveals saturation with increasing plastic strains at stress levels that decrease with increasing test temperatures. Numerical simulations are performed to correlate the experimentally observed temperature and strain rate dependence of flow stress at small and large plastic strains using the Austin-McDowell dislocation-mediated plasticity model parametrized to normal plate impact experiments conducted in an earlier study by Zaretsky and Kanel (2012). Extensions to the model are made to better represent dynamic behavior of pure aluminum at larger plastic strains as observed in elevated temperature split Hopkinson Pressure bar (SPHB) experiments of Samanta (1971) and Lindholm and Yeakly (1965), and the combined pressure-and-shear plate-impact experiments conducted in the present study. The main theoretical extension to the Austin-McDowell model made in this paper is the introduction of a new rate- and temperature- dependent dynamic recovery function, which can potentially allow for an effective reduction in the rate of accumulation of dislocations at large plastic strains. The numerical predictions of the revised and re-calibrated plasticity model are brought into agreement with the experimental observations, correlating sufficiently well with dynamic yield stress at incipient plasticity and the flow stress levels at larger plastic strains, plastic strain rates in the range 10 3 – 10 6 /s, and elevated temperatures up to near melt. The model, in concert with the experimental measurements, suggests that at incipient plasticity the rate governing mechanism for plastic flow is phonon-drag restricted dislocation glide, whereas, at higher magnitudes of plastic strain, it transitions to stress-assisted thermally activated glide. The transition between these two rate governing mechanisms is controlled by the evolution of dislocations throughout the deformation process.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Local residual stresses and microstructure within recrystallizing grains in iron

The intragranular strains and the microstructure within recrystallizing grains in single phase pure iron have been systematically studied in 3D using synchrotron micro-diffraction. In contradiction to common knowledge we observe that residual elastic strains of up to 1–2 × 10 –3 are present in the recrystallizing grains. The local strain variations within individual grains can be similar in magnitude to those between different grains. The effects of processing parameters, including rolling reduction, recrystallized volume fraction, and cooling rate, as well as microstructural parameters, including grain size, orientation and internal misorientation, on the development of local residual elastic strains and microstructure have been quantified. It is suggested that the difference in local defect density between recrystallized grains and the surrounding deformed matrix, as well as the redistribution of medium to long-range residual stresses in the deformed grains, are the main reasons for the development of such strains in the recrystallized grains. The local residual stress levels are calculated and their possible impact on the mechanical properties and recrystallization processes are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Structure and Sulfur: Tuning the Viscoelastic and Surface Properties of Natural Keratin Fibers

Natural keratin fibers, such as wool, possess a complex hierarchical structure that governs their mechanical properties and surface energy. However, the extent to which these characteristics are influenced by combined contributions of structural variations (e.g., fiber diameter, intermediate filament (IF) packing) and chemical composition (e.g., disulfide bond density) remains poorly understood. In this study, we investigate wool fibers from five sheep breeds (Merino, Polwarth, Cheviot, Eider, and Devon) to elucidate how these factors influence viscoelasticity and surface interactions. Using a multimodal approach integrating interfacial and bulk characterization methods, including inverse gas chromatography (IGC), atomic force microscopy-infrared spectroscopy (AFM-IR), X-ray photoelectron spectroscopy (XPS), uniaxial tensile testing, and synchrotron small-angle X-ray scattering (SAXS), we show that the nanometer-thick 18-methyleicosanoic acid (18-MEA) layer is consistently present across all wool types and plays a key role in governing hydrophobicity and surface heterogeneity. A controlled isothermal treatment at 200 °C, designed to cleave disulfide bonds, results in a nearly 40% reduction in specific surface area across all fiber types, accompanied by a significant decrease in tensile strength and 80% reduction in elongation at break for Merino and Devon wool, but limited influence on the mechanical properties of Eider fibers. Furthermore, rate-dependent tensile testing within the elastic regime reveals distinct viscoelastic responses among the fiber types, suggesting that the sulfur-rich protein matrix surrounding IFs and its structure contribute actively to stress partitioning. Altogether, when combined with conclusions from SAXS measurements of IF spacing, our work offers compelling insights into the role of the keratin-associated protein (KAP) matrix in shaping wool fiber mechanics. Differences in mechanical behavior among wool types, despite similar IF spacing or sulfur content, highlight the importance of matrix composition and cross-linking density, suggesting that the molecular architecture of the KAP network may be a dominant factor in determining fiber performance.

X-ray scattering↗