Representative volume elements for plasticity and creep measured from high-resolution microscale strain fields
Not provided.
Materials Science↗
SEARCH · Search NASA
Results for “representative volume elements”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Measuring representative volume elements from high-resolution grain-scale strain fields
Most crystalline materials present a highly heterogeneous response at the microscale, which can be affected by both internal factors (such as microstructural parameters) and external factors (such as loading). Relating microscale inhomogeneities to the macroscale response of a material requires the use of homogenisation techniques, usually based on the concept of a representative volume element (RVE)—the smallest volume of material that represents the global average response. Here, in this work, we present a new and robust experimental method of measuring the size of a strain-based RVE from high-resolution grain-scale strain fields obtained using digital image correlation (DIC). The proposed method is based on the statistical (stereological) nature of the RVE, which has been widely adopted in numerical studies, and involves dividing a strain field into randomly selected regions of varying sizes and statistically analysing the distributions of average strains within them. To validate the new method, we generate a large number of synthetic strain fields from a fractional Gaussian noise algorithm. The proposed stereological method is shown to be capable of producing reliable RVE measurements from a very large range of possible microscale strain fields while at the same time being robust in that it can produce RVE measurement results even in cases where other existing methods may be unable to do so. The proposed method has a low field-of-view requirement, only needing a field-of-view about 1.2 times as large as the RVE to produce reliable measurements. In addition, the stereological method offers significant flexibility since its statistical nature allows for control over how strict the RVE measurement should be in each case.
36 MATERIALS SCIENCE↗
Observation and Modeling of Dynamic Fracture Behaviors of Battery Cell Under Impact Loading Using Enhanced Representative Volume Element Concept
The burgeoning electric automobile industry has increased interest in battery safety. Battery cells experience significant mechanical stress during operation, including the impact of accidents and vibrations from driving. The potential for thermal runaway reactions in battery cells raises safety concerns. Although numerous researchers have defined the dynamic behavior of battery cells and proposed numerical models to describe it, few studies have focused on the high-strain rate mechanical impact phase correlated with the onset of fracture. In this study, we describe the dynamic behavior of pouch battery cells and propose a modeling method to study their mechanical failure under impact situations. Impact tests are conducted at various velocities and heights. To overcome numerical issues commonly encountered under rapid deformation scenarios, a new finite element model is developed based on the representative volume element model. The proposed approach efficiently simulates continuous crack propagation and brittleness behavior during impact by permitting the individual behavior of the cell components. Therefore, engineers can reliably design safer electric vehicle battery cells by measuring the properties of the cell components.
ENERGY STORAGE↗
On the elastic problem of representative volume element for multiphase thin films
Not Available
Ahmad, Ahmad (ORCID:0000000249728954)↗
Graph neural networks for mechanical property prediction of 2D fiber composites
This work investigates the ability of graph neural networks (GNNs) to homogenize 2D fiber composite microstructures. We use different inhomogeneity and anisotropy indices to motivate and show that the Volume Elements (VEs) used in ML methods should ideally be far from their Representative Volume Element (RVE) size limit and, consequently, are notably anisotropic. Hence, training only the isotropic limit properties may not be acceptable. Another aspect is the need to normalize elastic stiffness values for ML, especially when high elastic contrast ratios are encountered between composite phases or in the material set. We introduce a normalization technique based on the mean-field method (MFM) to handle such high contrast ratios and train for the entire stiffness tensor. We show that the proposed GNN approaches exhibit high accuracy and efficiency compared to traditional methods and convolutional neural networks, utilizing unstructured graphs constructed from microstructure topology. Our model successfully predicts the stiffness tensor, peak strength under bulk damage, and brittle fracture initiation strength across diverse microstructure configurations while maintaining high accuracy even for extreme material contrasts and volume fractions. We also present a method to improve prediction accuracy for small dataset sizes using Voronoi partitioning.
Brittle strength↗
Statistical Homogenization of Elastic and Fracture Properties of a Sample Selective Laser Melting Material
Selective laser melting (SLM) is an additive manufacturing technique commonly used in the rapid prototyping of components. The complexity of the SLM microstructure poses a unique challenge to deriving effective mechanical properties at different length scales. Representative volume elements (RVEs) are often used to homogenize the material properties of composites. Instead of RVEs, we use statistical volume elements (SVEs) to homogenize the elastic and fracture properties of the material. This relates the inherent variation of a material’s microstructure to the variation in its mechanical properties at different observation scales. The convergence to the RVE limit is examined from two perspectives: the stability of the mean value as the SVE size increases for the mean-based approach, and the tendency of the normalized variation in homogenized properties to zero as the SVE size increases for the variation-based approach. Fracture properties tend to make the RVE limit slower than do elastic properties from both perspectives. There are also differences between vertical (normal to printing plane) and horizontal (in-plane) properties. While the elastic properties tend to make the RVE limit faster for the horizontal direction, i.e., having a smaller variation and more stable mean value, the fracture properties exhibit the opposite effect. We attributed these differences to the geometry of the melt pools.
36 MATERIALS SCIENCE↗
On the Representativity of Electrode Microstructure Parameters and Their Electrochemical Response for Lithium Ion Batteries
Lithium-ion battery electrochemical models require an accurate description of the electrodes microstructures to be predictive that can be achieved through nanoscale imaging. Such observations are however limited by their field of view (FOV), as they provide only a subset of the whole electrode volume that does not necessarily represent the whole electrode microstructure heterogeneity, and therefore can bias the microstructure analysis. A microstructure scale electrochemical model was used to investigate lithium plating onset, material non-uniform utilization, and in-plane heterogeneities for an NMC-graphite full cell. To evaluate the representativeness, and thus relevance, of these model predictions, a coupled representativity analysis has been performed on the microstructure parameters and, in a novel way, on the full cell electrochemical response. Electrode microstructure parameters representativeness has been first quantified using the representative volume element (RVE) methodology. The RVE major flaw is that ultimately it can only conclude if a FOV contains representative subvolumes of the FOV, but not if the FOV itself is representative of the electrode volume. Analysis can conclude negatively ('FOV is not representative'), but not positively ('FOV is representative'). One major contribution of this work was to quantify the convergence of the RVE size with the FOV, to actually investigate the FOV representativeness and thus partly remedy this intrinsic limitation. The analysis determined that performing a standard RVE calculation, without exploring its FOV convergence, is likely to strongly underestimate the actual RVE size. The new RVE methodology has been automated in the NREL open-source Microstructure Analysis Toolbox (MATBOX) and is available to the battery community. Representativeness of microstructure parameters is however only an intermediate step, as the end-results of an electrochemical model are performances predictions. Indeed, what is the practical consequence of a given deviation for a microstructure parameter? The microstructure parameter deviation propagations to the 3D microstructure scale electrochemical response have been then quantified for different charge rates. This defines a threshold for the microstructure parameters FOV for a desired maximum deviation of the electrochemical response. Such deviation propagation analysis is analogous to error propagation analysis and is necessary to determine the relevance of microstructure scale model predictions for macroscale predictions. Electrochemical model shows cell representative section areas are increasing with C-rate, due to higher in-plane heterogeneities, indicating larger FOVs are required specifically for fast charge modeling. Therefore, we introduced the novel concept of electrochemical RVE (eRVE) that is a function of the operating conditions (thus defined as a dynamic RVE), with an increasing dependence with the C-rate. Representativity analysis of the investigated cell determined a FOV of 144.4 x 54.4 m2 is large enough to establish a convergence on the representative section areas for low to intermediate C-rate (=2.5C), but not large enough to conclude for higher rates. This work aims to emphasize the importance of representativity analysis for LIB electrode microstructures, as it is required to estimate the error, and thus the relevance, of microstructure parameters intended to be used in macroscale models. The methodology and results can help researchers to select the relevant imaging and associated FOV required to provide accurate enough microstructure parameters.
ADVANCED PROPULSION SYSTEMS↗
Revisiting the empirical particle-fluid coupling model used in DEM-CFD by high-resolution DEM-LBM-IMB simulations: A 2D perspective
The work investigates the applicability of the unresolved Computational Fluid Dynamics and Discrete Element Method (CFDDEM) technique based on empirical equations for fluid-particle coupling. We first carry out a series of representative volume element simulations using the high-resolution particle-resolved Lattice Boltzmann method and Discrete Element Method (LBMDEM) coupled by an Immersed Moving Boundary (IMB) scheme. Then, we compare the results obtained by both LBMDEM and empirical equations used in unresolved CFDDEM with analytical solutions. It is found that the existing empirical equations used in solving fluid-particle interactions in 2D CFDDEM fail to accurately calculate the hydrodynamic force applied to solid particles. The underlying reason is that the existing empirical models are obtained based on 3D experimental results and thus are not applicable to 2D problems. Based on the simulation results, a new drag coefficient model is then proposed. The estimated drag forces using the new model are compared favourably with the simulated ones, indicating the good performance of the proposed model.
42 ENGINEERING↗
An FFT-based approach for Bloch wave analysis: application to polycrystals
A method based on the Fast Fourier Transform is proposed to obtain the dispersion relation of acoustic waves in heterogeneous periodic media with arbitrary microstructures. The microstructure is explicitly considered using a voxelized Representative Volume Element (RVE). The dispersion diagram is obtained solving an eigenvalue problem for Bloch waves in Fourier space. To this aim, two linear operators representing stiffness and mass are defined through the use of differential operators in Fourier space. The smallest eigenvalues are obtained using the implicitly restarted Lanczos and the subspace iteration methods, and the required inverse of the stiffness operator is done using the conjugate gradient with a preconditioner. The method is used to study the propagation of acoustic waves in elastic polycrystals, showing the strong effect of crystal anistropy and polycrystaline texture on the propagation. It is shown that the method combines the simplicity of classical Fourier series analysis with the versatility of Finite Elements to account for complex geometries proving an efficient and general approach which allows the use of large RVEs in 3D.
97 MATHEMATICS AND COMPUTING↗
Modeling deformation and failure in AlSi-polyester abradable sealcoating material using microstructure-based finite element simulation
A plasma-sprayed aluminum-silicon (AlSi)/polyester coating is applied in modern gas turbine engines as an abradable sealcoating to maintain tight clearances between the rotating blades and the static casing. While running the engine, the rotating blades “rub” with the abradable coating, which results in extreme strain rate (up to 10 6 ) dynamics and a high-temperature environment. Due to the difficulty of collecting direct measurements, predictive computational models are important for analyzing the deformation and failure of the abradable material, to help meet the design target of avoiding damage to the blade tip and maintaining high fuel efficiency. In this research, a microstructure-based finite element (FE) computational model was developed to capture the complex mechanical behavior of the AlSi/polyester microstructure. The model is based on a virtual representative-volume-element (RVE) of a metal-polymer microstructure, reconstructed from x-ray computed tomography. It models the plastic deformation of, and damage to, each AlSi and polyester constituents, as well as the failure at their interface. The model was calibrated and validated with uniaxial tension and compression experiments, conducted at two temperatures (298 K and 533 K) at an applied strain rate of 10 3 - 10 4 s -1 . The material exhibited strongly asymmetric tension-compression behavior and a sensitivity to temperature, which was well captured by the model. The model was further applied to investigate changes in mechanical behavior due to variations in constituents’ volume fractions, which provides guidance to the microstructural design of AlSi/polyester abradable materials. The model is expected to facilitate the development of improved abradable materials by bypassing the conventional trial-and-error approach and extensive testing requirements.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Simulated effect of defect volume and location on very high cycle fatigue of laser beam powder bed fused AlSi10Mg
This study quantifies the interaction between volumetric defect location and size on the very high cycle fatigue (VHCF) of laser beam powder bed fused (LB-PBF) AlSi10Mg. Crystal plasticity finite element method (CPFEM) simulations were used to investigate the effects of defect location and size on the driving force for crack initiation. The CPFEM model was calibrated against uniaxial and cyclic experimental data of LB-PBF AlSi10Mg. Defect characteristics were informed by experimental data from the specimens produced in various geometries to create realistic representative volume elements (RVEs) with equivalent volume fractions of defects. By embedding defects of varying sizes and locations within the RVEs, fatigue indicator parameters (FIPs) were calculated to analyze the impact of defects’ characteristics on fatigue performance. Different combinations of defect volume and locations were generated for various microstructure instantiations, providing insight into extreme value fatigue responses. Larger defect volumes located on free surfaces consistently generated the highest FIPs, suggesting defect size and boundary proximity intensify stress concentration effects. RVEs with multiple smaller defects produced lower FIPs than those with single large critical defects. These findings underscore the critical role of defect characteristics on fatigue life, providing a foundation for future predictive modeling in fatigue-sensitive AM applications.
AlSi10Mg↗
An Advanced Meso-Scale Peridynamic Modeling Technology using High-Performance Computing for Cost-Effective Product Design and Testing of Carbon Fiber Reinforced Polymer Composites in Light-weight Vehicles
We study a peridynamic composite modeling technology based on the discontinuous Galerkin finite element method, implemented in the commercial LS-DYNA software, for modeling and prediction of failure in carbon fiber reinforced polymer composites. The proposed technology is developed for the material failure analysis at the meso-scale, which provides the prevailing fiber-matrix interaction mechanism, without adoption of the representative volume element method and thus avoiding complicated numerical calibration procedures. Three types of experimental tests—in-plane coupon test, out-of-plane coupon test, and a component crash test—are simulated in a high-performance computing environment to assess the performance of the proposed peridynamic composite modeling technology.
36 MATERIALS SCIENCE↗
Machine-Learning-Based Multiscale Methods for 3D Modelling of Granular Materials by Incorporating History-Dependent State Variables
Over the past decades, the prevalence of machine learning (ML) methods has made the development of ML-based constitutive models for granular materials undoubtedly a popular subject. Numerous studies have been made to feature the loading path or history-dependent stress-strain response of granular media using neural networks. In this work, a novel finite element method (FEM)–ML multiscale approach was developed by incorporating internal variables to improve the simulation accuracy of 3D history-dependent granular materials for the first time. To this end, a surrogate constitutive model based on the single-step-based multi-layer perceptron (MLP) neural network was used to replace representative volume element (RVE) simulations conducted by the discrete element method (DEM) in the multiscale FEM–DEM approach. Although the prediction principle of the MLP aligns with the FEM algorithm, artificially added internal variables are required to differentiate the loading history. To address this issue, history variables associated with the Frobenius norm are proposed to be fed into the MLP coupled with the strain tensor to extract the history-dependent behaviour of granular assemblies. The developed FEM–ML approach was demonstrated in 3D conventional triaxial compression (CTC) simulations. Compared to the multiscale FEM–DEM approach, the proposed FEM–ML method exhibits a significantly improved computational efficiency.
granular materials↗
Seamlessly joining length scales: From atomistic thermal graphs to anisotropic continuum conductivity
Thermal transport in complex solids is governed by local structure, defects, and anisotropy, yet most continuum models still rely on oversimplified and homogenized conductivities. Here, we bridge atomistic and continuum descriptions by building finite element (FE) models directly from the site-projected thermal conductivity (SPTC), an atomic-level decomposition of the Green–Kubo thermal conductivity. We introduce a toolkit, the “Simulator Collection for Atomic-to-Continuum Scales (SCACS)”, which uses a graph neural network to predict SPTC on large atomic structures, coarse-grains these fields into anisotropic conductivity tensors, and embeds them into the heat-flow FE equation with a customized, anisotropy-aware adaptive mesh refinement scheme. Applied to silicon nanostructures, the resulting FE models act as representative volume elements, reproduce bulk conductivities, and capture interfacial and defect-driven anisotropy while maintaining thermodynamic consistency. Additionally, SCACS predicts experimental conductance trends and fields. This work demonstrates a general route for transferring atomistic transport information into device-scale thermal simulations with physics-based approximations.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Multi-fidelity Uncertainty Quantification for Homogenization Problems in Structure-Property Relationships from Crystal Plasticity Finite Elements
Crystal plasticity finite element method (CPFEM) has been an integrated computational materials engineering (ICME) workhorse to study materials behaviors and structure-property relationships for the last few decades. These relations are mappings from the microstructure space to the materials properties space. Due to the stochastic and random nature of microstructures, there is always some uncertainty associated with materials properties, for example, in homogenized stress-strain curves. For critical applications with strong reliability needs, it is often desirable to quantify the microstructure-induced uncertainty in the context of structure-property relationships. However, this uncertainty quantification (UQ) problem often incurs a large computational cost because many statistically equivalent representative volume elements (SERVEs) are needed. In this article, we apply a multi-level Monte Carlo (MLMC) method to CPFEM to study the uncertainty in stress-strain curves, given an ensemble of SERVEs at multiple mesh resolutions. By using the information at coarse meshes, we show that it is possible to approximate the response at fine meshes with a much reduced computational cost. We focus on problems where the model output is multi-dimensional, which requires us to track multiple quantities of interest (QoIs) at the same time. In conclusion, our numerical results show that MLMC can accelerate UQ tasks around 2.23x, compared to the classical Monte Carlo (MC) method, which is widely known as ensemble average in the CPFEM literature.
36 MATERIALS SCIENCE↗
A sensitivity analysis of twinning crystal plasticity finite element model using single crystal and poly crystal Zircaloy
The popularity of crystal plasticity finite element method (CPFEM) models is increasing due to their ability to predict the mechanical response of crystalline materials such as metals and metal alloys more accurately than traditional continuum mechanics models. This is since the crystal plasticity models consider the effect of atomic structure, microstructural morphology, and properties of individual grains. These CPFEM models use a large number of material parameters in order to capture the mesoscale physics which comes with the downside of the tedious calibration process. In this paper, a CPFEM code was developed to include the twinning induced grain reorientation and subsequent crystallographic slip for HPC material. The developed code is incorporated in a large-scale, parallelized nonlinear solver WARP3D. Further, a sensitivity analysis with respect to 22 material parameters was then conducted using single crystal and polycrystal representative volume element (RVE) of Zircaloy material. Loading was applied along five different crystallographic orientations for single crystal RVE and along three directions namely, rolling (RD), transverse (TD), and normal (ND) direction for polycrystal RVE. Results obtained from the sensitivity analysis were used for the calibration of material parameters for Zircaloy. Finally, developed code along with calibrated material parameters was used to investigate the effect of the hydride phase formation in Zircaloy which is a typical case observed for nuclear applications. It was found that the volume fraction of the hydride phase has a significant impact on the mechanical properties of Zircaloy.
36 MATERIALS SCIENCE↗
Non-conformal interface-cohesive modeling with the shifted boundary method
The accurate simulation of boundary- and interface-dominated problems on complex geometries remains challenging when boundary- or interface-fitted meshes are difficult to generate, particularly for curved boundaries, polycrystalline microstructures, and dense interface networks. The Shifted Boundary Method (SBM) alleviates this meshing burden by shifting the enforcement of boundary conditions from the true boundary to a nearby surrogate boundary and recovering the effect of the true boundary through geometric correction terms, thereby enabling standard finite element spaces on non-boundary-fitted meshes. In this report, we develop a general shiftedboundary and shifted-interface framework within the open-source MOOSE framework. We first present a general SBM implementation for complex geometries on non-boundary-fitted meshes. We then adopt the Shifted Interface Method (SIM) for internal interfaces and develop a unified shifted-interface treatment in which the interface law is enforced on a surrogate interface and the effect of the true interface is recovered through shifted jumps, fluxes, and tractions. This perspective brings scalar thermal-contact and vector-valued cohesive-zone mechanics into a single framework, the latter realized as the Shifted Cohesive Zone Method (SCZM) and coupled with history-dependent constitutive models from NEML2. We further extend the MOOSE mesh infrastructure to support cohesive-zone calculations on distributed meshes. The framework is verified and demonstrated through three progressive studies: Poisson’s equation on a smoothed starshaped domain, a manufactured thermal-contact problem on a non-interface-fitted mesh, and a two-dimensional polycrystalline representative volume element combining crystal plasticity with cohesive grain-boundary interfaces. Across these studies, the shifted formulations reproduce boundary- and interface-fitted reference solutions with high fidelity, indicating that the proposed framework provides an accurate and efficient route to boundary- and interface-dominated simulations on arbitrary geometries without requiring fitted meshes.
Yang, Cheng-Hau↗
Pore Resolved Simulations of Joule Heating in Fibrous Media using an Embedded Boundary Method
Joule heating has been regarded as an energy-efficient and sustainable method for heating materials and gases at large scales. The modeling of local temperature effects at pore-resolved scales for such systems, however, has been difficult to achieve due to challenges in coupling thermo-chemical processes in complex porous media and in large representative volume elements (RVEs). To this end, we developed an electro-thermal model at the pore scale to study Joule heating effects in large heterogeneous systems with different microstructures. This was achieved using the level set method to implicitly delineate distinct regions within the domain, and an embedded boundary method to facilitate heat exchange across the fluid-solid interface. Moreover, we applied this method to investigate unsteady non-linear electro-thermal effects in non-woven fibrous graphite conductors for RVEs with characteristic lengths of 2 mm, with different fiber orientations, porosity (80% – 90%) and fiber diameters (10 – 20µm). The coupled equations were solved numerically and they produced peak temperatures greater than 2000 K resulting in heating rates as high as 80,000 K/s. Moreover, the results depended strongly on the microstructure of the fiber skeleton and current density. Geometries with large fibers (∼ 20µm) had the highest average and peak temperatures with the mean temperature increasing by 3.9 % while the peak temperature increased by 9.9 %. Anisotropic domains on the other hand had the lowest mean and peak temperatures with peak and mean temperatures of 2293 K and 1437.7K respectively representing a corresponding 12.1% and 5.1% drop in the temperatures. An increase in porosity from 80% to 90%, however, led to an increase in the peak temperature by 5.1%.
Joule heating↗