Search NASA⌕ Search

SEARCH · Search NASA

Results for “rf”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Utilization of the CW magnetrons as coherent RF sources for superconducting RF accelerators

CW magnetrons designed and optimized for industrial heaters, driven by an injection-locking signal, were suggested to power Superconducting RF (SRF) cavities. However, the CW magnetrons, which are regenerative generators, are intended to operate in self-excitation mode, so, for reliable starting they use a large regenerative gain, causing a large regenerative instability in operation. Thus, power supply ripple, even shot noise, etc., lead to multiple sidebands forming a quasi-continuous noise spectrum at the carrier frequency. Therefore, in the traditionally used mode of operation and control, such magnetrons are inapplicable for powering high Q-factor SRF cavities. A new approach to operation and control of CW magnetrons considering non-stationary processes during start-up and operation makes it possible to find a mode of almost coherent RF generation of tubes with a significant reduction in regenerative instability and noise and increased efficiency. In our work is presented substantiation for the newly developed mode with an analysis of the new approach based on experimental results. •In this article, for the first time, non-stationary, regenerative processes are considered during the start-up and operation of CW magnetrons for powering high-Q superconducting RF cavities.•An analytical study, confirmed by experiments, showed that the traditionally used modes of starting and operating CW magnetrons are not suitable for powering high-Q superconducting RF cavities.•In fact, to make CW magnetrons suitable for such cavities, the physics of starting and operating CW magnetrons must be changed. This has been demonstrated in our work.•In developing the Stimulated Coherent Generation Mode [NIM A 980 (2020) 164366], we have shown the suitability of this mode for starting and operating CW magnetrons for high-Q superconducting RF cavities.•Analytical analysis, verified experimentally, substantiates in our article the suitability of the “Mode of stimulated coherent generation” of CW magnetrons for powering high-Q superconducting cavities in pulsed and continuous modes.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Modeling of standing wave RF cavities for tracking through multi-pass energy recovery linac

Short bunches, high current and multiple linac pass are all characteristics of Energy Recovery Linacs (ERLs), which may result in collective effects. They in turn, may affect the beam, degrading its quality, or even yield to instabilities causing a beam loss. To study and mitigate these effects one needs a numerical simulation code, that can take into account both the collective effects, as well as, particular ERL features, such as a multi-turn design that does not reach a steady state or the multiple passages of the beam through Radio-Frequency (RF) cavities at different energies. CODAL [1], a code developed by SOLEIL in collaboration with IJCLab, enables such studies. It is a 6 dimensional (6D) tracking code applying 'kicks' based on the integration of the local Hamiltonian for each element of the lattice. It is also capable of simulating space charge, wakefields and coherent synchrotron radiation. However, to correctly take into account the ERL dynamics, an upgrade had to be made to include the effect of a standing wave RF cavity in 6D. In this paper, we will concentrate on the implementation and benchmarking (with DESY’s tracking code ASTRA [2]) of both the longitudinal and the transverse models (by J.B. Rosenzweig and L. Serafini [3]), which we use to carry out tracking of fully analytical 6D RF cavity.

Bogacz, A.↗
DOE OSTI2025

Fast-RF-Shimming: Accelerate RF shimming in 7T MRI using deep learning

Ultrahigh field (UHF) Magnetic Resonance Imaging (MRI) offers an elevated signal-to-noise ratio (SNR), enabling exceptionally high spatial resolution that benefits both clinical diagnostics and advanced research. However, the jump to higher fields introduces complications, particularly transmit radiofrequency (RF) field ($B^{+}_{1}$) inhomogeneities, manifesting as uneven flip angles and image intensity irregularities. These artifacts can degrade image quality and impede broader clinical adoption. Traditional RF shimming methods, such as Magnitude Least Squares (MLS) optimization, effectively mitigate $B^{+}_{1}$ inhomogeneity, but remain time-consuming. Recent machine learning approaches, including RF Shim Prediction by Iteratively Projected Ridge Regression and other deep learning architectures, suggest alternative pathways. Although these approaches show promise, challenges such as extensive training periods, limited network complexity, and practical data requirements persist. In this paper, we introduce a holistic learning-based framework called Fast-RF-Shimming, which achieves a 5000 ​× ​speed-up compared to the traditional MLS method. In the initial phase, we employ random-initialized Adaptive Moment Estimation (Adam) to derive the desired reference shimming weights from multi-channel $B^{+}_{1}$ fields. Next, we train a Residual Network (ResNet) to map $B^{+}_{1}$ fields directly to the ultimate RF shimming outputs, incorporating the confidence parameter into its loss function. Finally, we design Non-uniformity Field Detector (NFD), an optional post-processing step, to ensure the extreme non-uniform outcomes are identified. Comparative evaluations with standard MLS optimization underscore notable gains in both processing speed and predictive accuracy, which indicates that our technique shows a promising solution for addressing persistent inhomogeneity challenges.

Deep learning↗
DOE OSTI2026

Analysis of RF Sheath-Driven Tungsten Erosion at RF Antenna in the WEST Tokamak

This study applies the newly developed STRIPE (Simulated Transport of RF Impurity Production and Emission) framework to analyze tungsten (W) erosion at RF antenna structures in the WEST tokamak. STRIPE integrates SolEdge3x for edge plasma backgrounds, COMSOL for 3D RF sheath potentials, RustBCA for sputtering yields, and GITR for impurity transport and ion energy–angle distributions. Building on prior work by Kumar et al. (2025) Nuclear Fusion, 65, 076039, which validated STRIPE for WEST ICRH discharge #57877, the present study provides a spatially resolved assessment of gross W erosion at both Q2 antenna limiters under ohmic and ICRH conditions. Simulations using 2D SolEdge3x profiles in COMSOL capture rectified sheath potentials exceeding 300 V, leading to strong upper-limiter localization. Both poloidal and toroidal asymmetries are observed and attributed to RF sheath effects, with modeled erosion patterns deviating from experiment—highlighting sensitivity to sheath geometry and plasma resolution. Erosion is driven primarily by high-charge-state oxygen ions (O6+–O8+), while D+ plays a negligible role. Assuming a plasma composition of 1% oxygen and 98% deuterium, STRIPE predicts a 30-fold increase in gross W erosion from ohmic to ICRH phases, consistent with a >25-fold rise in W-I (400.9 nm) brightness. Quantitative agreement is within 5% in the ohmic phase and 30% under ICRH, demonstrating predictive capability. Importantly, the study shows that the magnitude of ICRH-driven W erosion depends strongly on the concentration of light impurities (O, B, N, C), which drive sputtering through high charge states. Cleaner plasma conditions with reduced impurity content are therefore expected to substantially mitigate antenna W sources in WEST and other toroidal fusion devices. These findings establish STRIPE as a predictive framework for RF-induced plasma–material interactions and support its application to reactor-scale antenna design.

Kumar, Atul [ORNL] (ORCID:0000000277475210)↗
NASA NTRS2007

Airborne RF Measurement System (ARMS) and Analysis of Representative Flight RF Environment

Environmental radio frequency (RF) data over a broad band of frequencies (30 MHz to 1000 MHz) were obtained to evaluate the electromagnetic environment in airspace around several airports. An RF signal measurement system was designed utilizing a spectrum analyzer connected to the NASA Lancair Columbia 300 aircraft's VHF/UHF navigation antenna. This paper presents an overview of the RF measurement system and provides analysis of sample RF signal measurement data. This aircraft installation package and measurement system can be quickly returned to service if needed by future projects requiring measurement of an RF signal environment or exploration of suspected interference situations.

Koppen, Sandra V.↗
DOE OSTI2021

FEbeam: Cavity and electron emission data conversion, processing, and analysis. A freeware toolkit for rf injectors

FEbeam is an all-in-one field emission data processing interface with the capability to analyze the field emission cathode performance in an rf injector by extracting the field enhancement factor, local field, and effective emission area from the Fowler–Nordheim equations. It also has the capability of processing beam imaging micrographs using its sister software, FEpic. Furthermore, the current version of FEbeam was designed for the Argonne Cathode Test-stand of the Argonne Wakefield Accelerator facility switch yard. With slight modifications, FEbeam could work for many rf field emission injectors. This software is open-source and can be found at GitHub.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

RF sheath induced sputtering on Proto-MPEX. I. Sheath equivalent dielectric layer for modeling the RF sheath

The pulsed linear plasma device Prototype Material Plasma Exposure eXperiment (Proto-MPEX) uses a radio frequency (RF) helicon antenna with an aluminum nitride ceramic window for plasma production. The RF sheath created under the helicon antenna is sufficient to cause ion impact energies to be greater than the sputtering threshold of the AlN helicon window material and for impurities to be created. In this study, we investigate the RF sheath on the inner diameter of the helicon window and its impact on the impurity production rates in Proto-MPEX. Three models—a 3D COMSOL finite element RF model of the Proto-MPEX helicon region, a rectified DC sheath potential model, and the 3D Global Impurity TRansport code—are coupled together to study impurity production and transportation. This novel method of impurity generation and transport modeling spans length scales ranging from the sheath (millimeters or less) up to the full device (meters) and can be applied to other radio frequency sources and antennas in a wide range of plasma physics studies, including basic plasmas, low-temperature processing plasmas, plasma thrusters, and fusion plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Analysis of RF losses and material characterization of samples removed from a Nb 3 Sn-coated superconducting RF cavity

Nb 3 Sn (T c ≈18 K and H sh ≈400 mT) is a prospective material to replace Nb (T c ≈9 K and H sh ≈200 mT) in SRF accelerator cavities for significant cost reduction and performance enhancement. Because of its material properties, Nb3Sn is best employed as a thin film (coating) inside an already built RF cavity structure. A particular test cavity noted as C3C4 was a 1.5 GHz single-cell Nb cavity, coated with Nb3Sn using Sn vapor diffusion process at Jefferson Lab. Cold measurements of the coated cavity indicated the superconducting transition temperature of about 18 K. Subsequent RF measurements indicated field-dependent surface resistance both at 4.3 K and 2.0 K. After initial cold measurements, the cavity RF loss distribution was studied with a thermometry mapping system. Loss regions were identified with thermometry and were cut out for material analysis. The presence of significantly thin patchy regions and other carbon-rich defects is associated with strong local field-dependent surface resistance. This paper summarizes RF and thermometry results correlated with material science findings.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

RF Accelerator Technology R&D: Report of AF7-rf Topical Group to Snowmass 2021

Accelerator radio frequency (RF) technology has been and remains critical for modern high energy physics (HEP) experiments based on particle accelerators. Tremendous progress in advancing this technology has been achieved over the past decade in several areas highlighted in this report. These achievements and new results expected from continued R&D efforts could pave the way for upgrades of existing facilities, improvements to accelerators already under construction (e.g., PIP-II), well-developed proposals (e.g., ILC, CLIC), and/or enable concepts under development, such as FCC-ee, CEPC, C 3 , HELEN, multi-MW Fermilab Proton Intensity Upgrade, future Muon Colloder, etc. Advances in RF technology have impact beyond HEP on accelerators built for nuclear physics, basic energy sciences, and other areas. Recent examples of such accelerators are European XFEL, LCLS-II and LCLS-II-HE, SHINE, SNS, ESS, FRIB, and EIC. To support and enable new accelerator-based applications and even make some of them feasible, we must continue addressing their challenges via a comprehensive RF R&D program that would advance the existing RF technologies and explore the nascent ones.

43 PARTICLE ACCELERATORS↗
NASA NTRS1979

Rate constant for the reaction H + NO2 from 195 to 400 K with FP-RF and DF-RF techniques

Measurements are made of the rate constant for the reaction H + NO2 yielding OH + NO over significant temperature ranges with the flash photolysis-resonance fluorescence (FP-RF) technique and also with the discharge flow-resonance fluorescence (DF-RF) technique. Since it is important to study chemical reactions with more than one technique, the above reaction is investigated with the FP-RF technique over the temperature range 230-400 K. The results reported do not agree with earlier determinations. Accordingly, a separate set of measurements is made with the DF-RF technique over the temperature range 195-368 K; the results are also reported. The reaction is also considered theoretically, especially with regard to the question of temperature dependence and absolute magnitude of the rate constant.

Michael, J. V.↗
NASA NTRS2007

Airborne RF Measurement System and Analysis of Representative Flight RF Environment

Environmental radio frequency (RF) data over a broad band of frequencies were needed to evaluate the airspace around several airports. An RF signal measurement system was designed using a spectrum analyzer connected to an aircraft VHF/UHF navigation antenna installed on a small aircraft. This paper presents an overview of the RF measurement system and provides analysis of a sample of RF signal measurement data over a frequency range of 30 MHz to 1000 MHz.

Koppen, Sandra V.↗
DOE OSTI2021

Superconducting RF Gun with High Current and the Capability to Generate Polarized Electron Beams

High-current low-emittance CW electron beams are indispensable for nuclear and high-energy physics fixed target and collider experiments, cooling high energy hadron beams, generating CW beams of monoenergetic X-rays (in FELs) and gamma-rays (in Compton sources). Polarization of electrons in these beams provides extra value by opening a new set of observables and frequently improving the data quality. We report on the upgrade of the unique and fully functional CW SRF 1.25 MeV SRF gun, built as part of the Coherent electron Cooling (CeC) project, which has demonstrated sustained CW operation with CsK2Sb photocathodes generating electron bunches with record-low transverse emittances and record-high bunch charge exceeding 10 nC. We propose to extend the capabilities of this system to high average current of 100 milliampere in two steps: increasing the current 30-fold at each step with the goal to demonstrate reliable long-term operation of the high-current low-emittance CW SRF guns. We also propose to test polarized GaAs photocathodes in the ultra-high vacuum (UHV) environment of the SRF gun, which has never been successfully demonstrated in RF accelerators.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Low RF loss DC conductive ceramic for RF windows

Charging of RF windows has historically been problematic, frequently resulting in damage to the window severe enough that the window needs to be replaced. Many attempts have been made to prevent charging and therefore improve window lifetime, the most successful and common of which is coating the window with titanium nitride (TiN). Surface coatings such as TiN rely on the secondary electron yield of the coating material being lower than that of the ceramic window material, reducing the number of electrons emitted from a variety of mechanisms. An alternative approach is to introduce a small amount of DC conductivity to the ceramic itself, turning the traditionally insulating window into a mildly conductive one. This allows any charge on the surface of the window to drain rather than build until a discharge happens. A magnesium titanate ceramic has been developed with a small DC conductivity and used to make RF windows. Several window assemblies have been produced and tested, including 1.3 GHz waveguide and 650 MHz coaxial designs. The results of the conductive ceramic window test program will be presented.

43 PARTICLE ACCELERATORS↗
NASA NTRS1988

Investigation of RF excited CW CO2 waveguide lasers local oscillator - RF excitation

A new local oscillator housing was built which seems to have improved laser life. Laser cooling was changed from internal water cooling to the more convenient thermal contact cooling. At the present time, a conclusion can not be made if the 20 percent reduction in power output is the result of poorer cooling or poorer grating alignment. The coupling-starting network was improved from 55 to about 90 percent. It can be adjusted by varying trimmers C sub 1 and C sub 2 to match RF power levels between 10 and 30 W. If the laser admittance changes greatly with laser life rematching will have to be achieved by remote control for space applications. The same holds true if the RF power level has to be changed with a maximum efficiency constraint.

Hochuli, U.↗
DOE OSTI2024

Observation of tantalum deposition and growth on TiB2 and ZrB2 from PISCES-RF deuterium and helium plasma exposures

Deuterium and helium plasma exposures on bulk TiB2 and ZrB2 samples were performed using the PISCES-RF linear plasma device. 40 and 90 eV deuterium ion plasma exposures were performed at 240 and 800 °C sample temperatures, and 80 eV helium ion plasma exposures were performed at 800 °C sample temperatures. Following plasma exposures, it was discovered that two plasma conditions (90 eV deuterium and 80 eV helium at 800 °C) resulted in thick (>200 nm) tantalum-rich (>10 at%) surface features on the targets, presumably from tantalum sourced from a tantalum adapter mask or cap used as part of the target holder. This work aims to characterize these tantalum-rich features and examine the mechanisms of impurity deposition.Plasma-induced surface morphology of the tantalum-rich surface layers depends on plasma properties and target temperature and chemistry. Greater titanium sputtering compared to zirconium resulted in more distinct surface features in the TiB2 samples compared to the ZrB2 samples via increased, prompt deposition onto tantalum surface impurities. There is still uncertainty as to why thick tantalum deposition only occurred under some plasma exposure conditions but not others; it is likely due to tantalum sputtering by a combination of boron molecules from the targets and carbon-impurities in the tantalum mask or targets. Impurity driven surface features are a well-documented phenomena in samples exposed to plasma from linear plasma device facilities—this work confirms the occurrence of this and emphasizes the need for chemistry characterization of isolated post-mortem surface features in plasma-exposed samples.

Nuckols, Lauren↗
DOE OSTI2022

Fusion RF Modeling Machine Learning (FusionML_RF) v1.0

FusionML_RF consists of multiple codes and trained machine learning (ML) models that perform low-cost output modeling from the Genray-CQL3D. Three machine learning techniques (multilayer perceptron, random forest, and Gaussian process) provide fast surrogate models for lower hybrid current drive (LHCD) simulations. For example, completing a single GENRAY/CQL3D simulation without radial diffusion of fast electrons requires several minutes of wall-clock time. On the other hand, these ML models achieve ~ms of inference time with high accuracy across the input parameter space. This software collection consists of multiple components. (1) codes that use ML methods and precomputed Genray-CQL3D simulation output to build regression models that enable approximate computations of Genray-CLQ3D outputs from arbitrary but physically meaningful input parameters (surrogate modeling); (2) three trained models created by the team, using a database of 16,000+ GENRAY/CQL3D simulations, to study the performance of ML models for surrogate modeling; (3) codes that load the trained models and simulation data, and then compute mean squared error between the models' predictions and the ground truth of simulation output data. This collection is being made available in conjunction with a scientific publication about the work to promote reusability and provide an artifact of the scientific work.

Bai, Zhe↗